Car-and-Safety.com

Ford Fusion 2010 Safety Reports and Reviews



Ford Fusion 2010 Reviews



Ford Fusion 2010 Visibility Windshield

Ford Fusion 2010 Visibility Windshield Review #10267371

FORD FUSION 2010 car safety problem was reported on Apr 27, 2009.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with VISIBILITY:WINDSHIELD . tl*the contact owns a 2010 ford fusion sport. the contact stated that the windshield contained a stress crack due to the heat. the vehicle was purchased on april 13, 2009. the vehicle is currently at the dealer being repaired at the cost of $300, which is half of the repair bill. the manufacturer stated that the vehicle was not covered under warranty; therefore, he has to pay for half of the repair. the failure mileage was 1,300. updated 05/13/09 *bf the service department concluded that a rock hit the windshield and the hot weather caused the crack to expand. the consumer believed the windshield was defective. updated 05/13/09.*jb.0 person(s) were injured. 0 person(s) died.Mileage was 1300 miles. Vehicle Identification Number (VIN):3FAHP0KC2AR. Ford Fusion 2010 problem was reported in ARLINGTON, VA. Original Owner. Vehicle was purchased on Apr 13, 2009. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph. DEALER'S NAME: KOONS FORD . DEALER'S TELEPHONE NUMBER: 703-241-7250 . DEALER'S CITY: FALLS CHURCH . DEALER'S STATE CODE: VA. DEALER'S ZIPCODE: 22044 .

Ford Fusion 2010 Visibility Review #10270140

FORD FUSION 2010 car safety problem was reported on Apr 10, 2009.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with VISIBILITY . car was purchased new car is 2010 fusion hybrid. noticed crack in windshield starting under rearview mirror do west for approx 3 inches. crack hasn't gotten bigger. didn't notice at time of delivery. *tr.Mileage was 10 miles. Ford Fusion 2010 problem was reported in BALDWINSVILLE, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Service Brakes, Electric

Ford Fusion 2010 Service Brakes, Electric Review #10273260

FORD FUSION 2010 car safety problem was reported on May 27, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, ELECTRIC . i bought a 2010 ford fusion hybrid on may 23, 2009 from crown ford of fayetteville, nc. on may 27, while driving down the road, the breaks suddenly hit the floor and there was minimal resistance. i eventually brought the car to a halt in a parking lot. it was towed to crown ford and they said it was only air in the breaks and the car was now safe for my family. 4 days later on may 31st while i was idling at a stop light with my daughter in the back seat, the breaks went to the floor/failed again and i had to utilized the emergency break to maneuver it to a safe place. crown ford said it was the wiring this time. i do not think ford knows what is going on with this vehicle since it has this new regenerative breaking system. what i do know is that as soon as my fusion hybrid was "fixed" again, i drove it straight to another dealership and traded it in for a different vehicle. i would never put my kids back in that car and am worried about other families who choose to buy this type of vehicle. *tr.Mileage was 200 miles. Vehicle Identification Number (VIN):3FADP0L35AR. Ford Fusion 2010 problem was reported in FAYETTEVILLE, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Latches/locks/linkages

Ford Fusion 2010 Latches/locks/linkages Review #10281453

FORD FUSION 2010 car safety problem was reported on June 11, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with LATCHES/LOCKS/LINKAGES . the hood on my 2010 ford fusion hybrid unlatches itself at interstate highway speed. the safety catch has successfully restrained the hood from flying open completely. there have been four incidents with three different drivers since the car was delivered. the date below was the first incident. *tr.Mileage was 600 miles. Vehicle Identification Number (VIN):3FADP0L33AR. Ford Fusion 2010 problem was reported in ALEXANDRIA, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Fuel System, Gasoline

Ford Fusion 2010 Fuel System, Gasoline Review #10284037

FORD FUSION 2010 car safety problem was reported on Sept 15, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE . trouble starting like the starter is defective, but that doesn't seem to be the problem. automatic transmission that jerks when shifting. *tr .Mileage was 2000 miles. Ford Fusion 2010 problem was reported in EVANSVILLE, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10284037

FORD FUSION 2010 car safety problem was reported on Sept 15, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . trouble starting like the starter is defective, but that doesn't seem to be the problem. automatic transmission that jerks when shifting. *tr .Mileage was 2000 miles. Ford Fusion 2010 problem was reported in EVANSVILLE, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train Automatic Transmission Review #10285614

FORD FUSION 2010 car safety problem was reported on Sept 28, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . tl*the contact owns a 2010 ford fusion. when accelerating uphill, the vehicle rolled backwards. as a consequence, his risk for a vehicle crash was increased. the vehicle has not been inspected to determine the cause of the failure; however, he is concerned that the transmission has failed. the failure and current mileages were 200..Mileage was 200 miles. Vehicle Identification Number (VIN):3FAHP0JG4AR. Ford Fusion 2010 problem was reported in MENTOR, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Seats

Ford Fusion 2010 Seats Review #10287396

FORD FUSION 2010 car safety problem was reported on Aug 08, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SEATS . the head rest on my new 2010 ford focus (not a fusion as noted) protrudes forward beyond the top of the seat causing my head and neck to be pushed forward into an unnatural position with my spine. this, in turn, is a very unsafe driving position to be in due to misalignment of my head, neck and spine and causes unnecessary fatigue, neck pain and headache . it is especially awkward and difficult to drive and look toward the right rear of the vehicle while being forced into a "crook neck" position by the forward protruding head rest. i purchased to vehicle new under the cash for clunkers program and without driving it. this was a big mistake as i got myself into an apparent unsafe vehicle. after driving it for only 40 miles, i experienced neck pain. my investigation revealed that the forward protruding head rest was the problem. i promptly notified the dealer where i bought it and was advised by my sales person that several other people have also complained about these head rests. i then notified ford motor company customer services of the problem and was advised, "the head rests are made to our specifications". i indicated that this is a safety issue and suggested that they do something about it before they have another firestone tire type of problem to deal with. the company rep. then proceeded to hang up on me. as a remedy to my complaint. the dealer (service manager) removed the head rests from the front seats of my new car and suggested that i, "go to a salvage (junk) yard and try to get replacement head rests that do not cause the problem". i reminded him that i had just turned in a '93 aerostar that did not have the problem and he replied, "we just sell the cars - we don't build them". with the head rests removed, i now have no protection from whiplash which is another safety problem. i respectfully request that the nhtsa investigate these head rests (asap) to prevent injury, death or property damage. a recall is needed here. thank you *tr.Mileage was 50 miles. Vehicle Identification Number (VIN):1FAHP3FN2AW. Ford Fusion 2010 problem was reported in CANTON, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Seats Review #10294648

FORD FUSION 2010 car safety problem was reported on Nov 24, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SEATS . my complaint is not specific to any particular automobile, but instead concerns the front seat headrests in many late-model vehicles. these headrests are angled too far forward and are causing drivers and front seat passengers to experience significant neck, back, and shoulder discomfort. this change in headrest design is too extreme. on the internet, i have read that many car owners are removing the headrests and replacing them with the forward surface facing rearward. others are removing these headrests altogether. it is understood that whiplash injuries may occur less frequently with the new standards, however the discomfort experienced while driving for even a short period of time is causing people to have headaches and neck and back symptoms that may eventually lead to related chronic conditions. *tr.Ford Fusion 2010 problem was reported in CARNEGIE, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Seats Review #10296446

FORD FUSION 2010 car safety problem was reported on Mar 24, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SEATS . since buying a new 2010 ford fusion hybrid, the head rest/restraints for both front seat passengers are made too far forward and touch the back of the head while driving. although we are told they are made this way for our safety, they are very annoying . the angle can not even be changed and we are still looking to replace them if we could just find ones that are just 1" further back. i have gone on-line on the internet and see lots of people complaining about the same issue and wonder why the nhtsa has not issued a recall or even required ford to provide a replacement for a small fee? they bother my wife so much that she has removed them from the seats. now we do not have any protection from a rear end collision. *tr.Mileage was 0 miles. Ford Fusion 2010 problem was reported in FARMINGTON HILLS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10299496

FORD FUSION 2010 car safety problem was reported on Oct 01, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . tl*the contact owns a 2010 ford fusion. the contact was driving approximately 15 mph on normal road conditions and applied pressure to the accelerator pedal, followed by no power response. the engine began to rev excessively and the rpm's increased rapidly. in addition, the transmission exhibited a delay and a hard shift. the failure occurred intermittently. the vehicle was able to resume normal operation. the vehicle has not been repaired at this time. the failure mileage was 1,000. the current mileage was 3,077. updated 02/02/10 *bf the consumer stated he has experienced a problem with delayed acceleration. the delay was always followed by a delayed rough shift. the transmission would always slam into gear after acceleration hesitation. updated 02/05/10.*jb .Mileage was 1000 miles. Vehicle Identification Number (VIN):3FAHP0JG1AR. Ford Fusion 2010 problem was reported in BEVERLY HILLS, MI. Original Owner. Vehicle was purchased on Aug 20, 2009. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: BIFUEL. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 15 mph. DEALER'S NAME: ELDER FORD . DEALER'S TELEPHONE NUMBER: 248-585-4000 . DEALER'S CITY: TROY . DEALER'S STATE CODE: MI. DEALER'S ZIPCODE: 48083 .

Ford Fusion 2010 Structure

Ford Fusion 2010 Structure Review #10299884

FORD FUSION 2010 car safety problem was reported on Nov 28, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE . tl*the contact owns a 2010 ford fusion. the contact was unable to read the speedometer due to the reflection of the sunlight glare through the tinted windows in the vehicle. the vehicle was taken to an authorized dealer for inspection. the technician stated the problem experienced was a manufacturer design. the manufacturer was notified and there was concern of the safety risk involved. the failure mileage was 300. *cn updated 02/19/10.Mileage was 300 miles. Vehicle Identification Number (VIN):3FAHP0JG3AR. Ford Fusion 2010 problem was reported in TORRANCE, CA. Original Owner. Vehicle was purchased on Oct 30, 2009. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: BIFUEL. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. DEALER'S NAME: POWER FORD . DEALER'S TELEPHONE NUMBER: 310-748-4700 . DEALER'S CITY: TORRANCE . DEALER'S STATE CODE: CA. DEALER'S ZIPCODE: 90505 .

Ford Fusion 2010 Electrical System Instrument Panel

Ford Fusion 2010 Electrical System Instrument Panel Review #10299884

FORD FUSION 2010 car safety problem was reported on Nov 28, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM: INSTRUMENT PANEL . tl*the contact owns a 2010 ford fusion. the contact was unable to read the speedometer due to the reflection of the sunlight glare through the tinted windows in the vehicle. the vehicle was taken to an authorized dealer for inspection. the technician stated the problem experienced was a manufacturer design. the manufacturer was notified and there was concern of the safety risk involved. the failure mileage was 300. *cn updated 02/19/10.Mileage was 300 miles. Vehicle Identification Number (VIN):3FAHP0JG3AR. Ford Fusion 2010 problem was reported in TORRANCE, CA. Original Owner. Vehicle was purchased on Oct 30, 2009. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: BIFUEL. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. DEALER'S NAME: POWER FORD . DEALER'S TELEPHONE NUMBER: 310-748-4700 . DEALER'S CITY: TORRANCE . DEALER'S STATE CODE: CA. DEALER'S ZIPCODE: 90505 .

Ford Fusion 2010 Fuel System, Gasoline Storage Tank Assembly

Ford Fusion 2010 Fuel System, Gasoline Storage Tank Assembly Review #10303178

FORD FUSION 2010 car safety problem was reported on Jan 28, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY . tl* the contact owns a 2010 ford fusion hybrid. the contact stated that she noticed gas pouring out of her gas tank. she had the vehicle towed to the dealership and there was a hole in the tank about the size of a quarter. the fire department had to be called out due to the fuel leakage. she did not know how the puncture could have happened. she called the manufacturer and was told that they would compile a report but offered no further assistance at the time. the current and failure mileages were approximately 20,000. .Mileage was 20000 miles. Vehicle Identification Number (VIN):3FADP0L33AR. Ford Fusion 2010 problem was reported in CULLOM, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Service Brakes, Electric

Ford Fusion 2010 Service Brakes, Electric Review #10305554

FORD FUSION 2010 car safety problem was reported on Oct 20, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, ELECTRIC . 2010 ford fusion hybrid purchased 08/07/09 if i am reading the paperwork correctly it was manufactured in hermosillo, mexico 6/23/09 10/20/09 brakes failed (pedal goes to floor & warning dash lights lit), slowed with parking brake, brakes okay after engine turn off and restart. dealer found nothing, no codes, no tsb's, no ssm's 10/28/09 brakes failed as above, slowed with parking brake, brakes okay after engine turn off and restart. dealer found nothing, no codes. 10/30/09 brakes failed twice as above, slowed with parking brake, brakes okay after engine turn off and restart. dealer called ford. ford authorized free rental car and provided a technician to assist dealer. result: replaced brake booster travel sensor, reprogrammed pcm power train control module with later version of the software, there is a tech service bulletin on this but my car did not show the codes the first 2 times i brought it in. on the third time the factory showed the dealer how to look for codes in a different manner. 2/4/10 brakes are continuing to work fine since the dealer fixed them. this is not really a complaint, but i see others on the internet who are having this problem and the dealers appear to be having trouble like mind did. *tr.Mileage was 1602 miles. Vehicle Identification Number (VIN):3FADP0L36AR. Ford Fusion 2010 problem was reported in ORANGE, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Service Brakes, Electric Review #10307130

FORD FUSION 2010 car safety problem was reported on Oct 22, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, ELECTRIC . i experienced braking problems with my fusion hybrid multiple times nearly crashing into stopped cars. this was especially bad in rough conditions. the ford dealer told me it was my driving habits not the vehicle. *tw.Mileage was 550 miles. Vehicle Identification Number (VIN):3FADP0L37AR. Ford Fusion 2010 problem was reported in MENDHAM, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Equipment

Ford Fusion 2010 Equipment Review #10307311

FORD FUSION 2010 car safety problem was reported on Nov 30, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with EQUIPMENT . at times i am unable to read any information in the instrument cluster area. instruments are covered by a dark plastic and when the sun shines in the area of the instruments, you can not see them. my concern is the speed i am traveling. *tw.Mileage was 35 miles. Vehicle Identification Number (VIN):3FAHP0JG3AR. Ford Fusion 2010 problem was reported in TORRANCE, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10312927

FORD FUSION 2010 car safety problem was reported on Oct 15, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . our 2010 ford fusion is starting to split to split at the seams literally. on the passenger front door on the armrest where the window switch is, the panel is starting to separate & come apart. the top of the panel bulges upwards as if something in the door is pushing it up. my concern is especially here in nj with the recent snow & rain, moisture & dust could come in through the crack & either short out or disable the electrical wiring in the door (speakers, window, etc). the failure stared at 2000 miles & the split gets bigger each day & current mileage is 5300 miles. i'm sorry but i've bought ford for the last 15 years & this is probably the worst quality i've seen in ford cars. *tr.Mileage was 2000 miles. Ford Fusion 2010 problem was reported in BARNEGAT, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Structure

Ford Fusion 2010 Structure Review #10312927

FORD FUSION 2010 car safety problem was reported on Oct 15, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE . our 2010 ford fusion is starting to split to split at the seams literally. on the passenger front door on the armrest where the window switch is, the panel is starting to separate & come apart. the top of the panel bulges upwards as if something in the door is pushing it up. my concern is especially here in nj with the recent snow & rain, moisture & dust could come in through the crack & either short out or disable the electrical wiring in the door (speakers, window, etc). the failure stared at 2000 miles & the split gets bigger each day & current mileage is 5300 miles. i'm sorry but i've bought ford for the last 15 years & this is probably the worst quality i've seen in ford cars. *tr.Mileage was 2000 miles. Ford Fusion 2010 problem was reported in BARNEGAT, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Service Brakes, Electric

Ford Fusion 2010 Service Brakes, Electric Review #10313517

FORD FUSION 2010 car safety problem was reported on Feb 20, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, ELECTRIC . while under normal driving conditions and habits, we experienced a complete instrument cluster failure in our 2010 ford fusion hybrid this past saturday, feb 20. 2010. during the same incident we experienced a symptom of diminished power while accelerating as well as overly sensitive and /or mushy brakes. there have been other reported instances where the brake system has glitched as well during regenerative braking causing an abrupt application of hydraulic system over riding the regenerative system, brake system continues to have issues even after recall repair reprogramwas performed. we have had several instrument cluster glitches while driving the vehicle since purchase date of october 26, 2009. first incident was reported october 27, 2009. several. instrument cluster resets while driving since purchase date. first incident reported same date as previous.. on february 22, 2010 car stalled for no reason while driving 45mph in traffic to dealership to have instrument cluster and other issues addressed. restarted when car came ro a complete stop and placed in park. car is at dealer now and no codes were reported in systems. ford engineers state that with no codes reported there can't be any problems. *tr.Mileage was 6700 miles. Vehicle Identification Number (VIN):3FADP0L32AR. Ford Fusion 2010 problem was reported in COLONIAL HEIGHTS, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10313517

FORD FUSION 2010 car safety problem was reported on Feb 20, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while under normal driving conditions and habits, we experienced a complete instrument cluster failure in our 2010 ford fusion hybrid this past saturday, feb 20. 2010. during the same incident we experienced a symptom of diminished power while accelerating as well as overly sensitive and /or mushy brakes. there have been other reported instances where the brake system has glitched as well during regenerative braking causing an abrupt application of hydraulic system over riding the regenerative system, brake system continues to have issues even after recall repair reprogramwas performed. we have had several instrument cluster glitches while driving the vehicle since purchase date of october 26, 2009. first incident was reported october 27, 2009. several. instrument cluster resets while driving since purchase date. first incident reported same date as previous.. on february 22, 2010 car stalled for no reason while driving 45mph in traffic to dealership to have instrument cluster and other issues addressed. restarted when car came ro a complete stop and placed in park. car is at dealer now and no codes were reported in systems. ford engineers state that with no codes reported there can't be any problems. *tr.Mileage was 6700 miles. Vehicle Identification Number (VIN):3FADP0L32AR. Ford Fusion 2010 problem was reported in COLONIAL HEIGHTS, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10313517

FORD FUSION 2010 car safety problem was reported on Feb 20, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . while under normal driving conditions and habits, we experienced a complete instrument cluster failure in our 2010 ford fusion hybrid this past saturday, feb 20. 2010. during the same incident we experienced a symptom of diminished power while accelerating as well as overly sensitive and /or mushy brakes. there have been other reported instances where the brake system has glitched as well during regenerative braking causing an abrupt application of hydraulic system over riding the regenerative system, brake system continues to have issues even after recall repair reprogramwas performed. we have had several instrument cluster glitches while driving the vehicle since purchase date of october 26, 2009. first incident was reported october 27, 2009. several. instrument cluster resets while driving since purchase date. first incident reported same date as previous.. on february 22, 2010 car stalled for no reason while driving 45mph in traffic to dealership to have instrument cluster and other issues addressed. restarted when car came ro a complete stop and placed in park. car is at dealer now and no codes were reported in systems. ford engineers state that with no codes reported there can't be any problems. *tr.Mileage was 6700 miles. Vehicle Identification Number (VIN):3FADP0L32AR. Ford Fusion 2010 problem was reported in COLONIAL HEIGHTS, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Service Brakes, Electric

Ford Fusion 2010 Service Brakes, Electric Review #10316006

FORD FUSION 2010 car safety problem was reported on Feb 11, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, ELECTRIC . my wife called me after she was involved in a accident with our 2010 ford fusion hybrid. i told her to call our insurance company in carthage new york to report to them first as there was no damage to the car that she hit but some to ours. she gave the company the name and number of the other car involved to which they followed up with that they had no damage to their car. she took our car to the dealer to who i asked if they had any reports of brake failure on these cars. after being told of no trouble from ford i went online and found several issues with the hybrid brake system. i took the info back to them and they found the recall on these cars. my wife had no brakes when she tried to slow and hit the car to come to rest. no airbags were deployed as it was moving slow but after the original estimate of $120. to the high of $521. and because of the amount no claim to our insurance company i now after taking in to have repaired i have a new one of $1948. from the dealership. i contacted ford and they sent me forms if i decide to pursue a claim against them. the roads were dry,clear and she had no perceived braking on this car. the car has been fixed by the dealership on the recall and i certainly will file my claim with ford but the hoops that they want me to jump through appear to be unwarranted as to their brake problems that don't seem to get the attention that toyota is receiving on the same brake system. my dealer agrees with us that we are in no responsible for the repair but at this time i am stuck with trying to pursue litigation as the form states to resolve with ford. help please if you can or at least make aware that yes ford does have their own issues. the same brake failure or as ford says,perceived brake failure occurred with a consumer report engineer and that is where i originally found out to take the information to my dealership. thank you for any help you may be able to provide. *tr.Vehicle was involved in a crash. Mileage was 8800 miles. Vehicle Identification Number (VIN):3FADP0L32AR. Ford Fusion 2010 problem was reported in CARTHAGE, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10316620

FORD FUSION 2010 car safety problem was reported on Mar 04, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . this morning the gas pedal got stuck on the floor and i couldn't stop the car until a couple miles later. brakes did not stop the car until the gas pedal just came back up from the floor. please look into this before someone gets killed!! *tr.Mileage was 7440 miles. Vehicle Identification Number (VIN):3FADP0L3XAR. Ford Fusion 2010 problem was reported in WOODBRIDGE, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Vehicle Speed Control Review #10316655

FORD FUSION 2010 car safety problem was reported on Feb 04, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . my car is accelerating on its own. *tr.Mileage was 7600 miles. Ford Fusion 2010 problem was reported in CLAWSON, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10317487

FORD FUSION 2010 car safety problem was reported on Aug 01, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . ford fusion 2010 s - when the brake was depressed the car accelerated until i depressed a second time much harder. the consumer first began to notice the vehicle would intermittently not start in august. he took the vehicle to the dealer, but they were unable to duplicate the problem. the consumer insisted there was a problem and eventually, they found a technical service bulletin that addressed the issue. the problem was attributed to radio frequency intermittently corrupting the crankshaft position sensor and a new ground strip was installed. the problem seemed to be rectified. the weather stripping surrounding the rear window was loose, there was loose metal around the passenger rear wheel. *jb.Mileage was 11300 miles. Vehicle Identification Number (VIN):3FAHP0GA3AR. Ford Fusion 2010 problem was reported in SILVER SPRING, MD. Vehicle was purchased on June 28, 2009. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph. DEALER'S NAME: LINSAY FORD . DEALER'S CITY: WHEATON . DEALER'S STATE CODE: MD.

Ford Fusion 2010 Structure

Ford Fusion 2010 Structure Review #10317487

FORD FUSION 2010 car safety problem was reported on Aug 01, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE . ford fusion 2010 s - when the brake was depressed the car accelerated until i depressed a second time much harder. the consumer first began to notice the vehicle would intermittently not start in august. he took the vehicle to the dealer, but they were unable to duplicate the problem. the consumer insisted there was a problem and eventually, they found a technical service bulletin that addressed the issue. the problem was attributed to radio frequency intermittently corrupting the crankshaft position sensor and a new ground strip was installed. the problem seemed to be rectified. the weather stripping surrounding the rear window was loose, there was loose metal around the passenger rear wheel. *jb.Mileage was 11300 miles. Vehicle Identification Number (VIN):3FAHP0GA3AR. Ford Fusion 2010 problem was reported in SILVER SPRING, MD. Vehicle was purchased on June 28, 2009. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph. DEALER'S NAME: LINSAY FORD . DEALER'S CITY: WHEATON . DEALER'S STATE CODE: MD.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10317487

FORD FUSION 2010 car safety problem was reported on Aug 01, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . ford fusion 2010 s - when the brake was depressed the car accelerated until i depressed a second time much harder. the consumer first began to notice the vehicle would intermittently not start in august. he took the vehicle to the dealer, but they were unable to duplicate the problem. the consumer insisted there was a problem and eventually, they found a technical service bulletin that addressed the issue. the problem was attributed to radio frequency intermittently corrupting the crankshaft position sensor and a new ground strip was installed. the problem seemed to be rectified. the weather stripping surrounding the rear window was loose, there was loose metal around the passenger rear wheel. *jb.Mileage was 11300 miles. Vehicle Identification Number (VIN):3FAHP0GA3AR. Ford Fusion 2010 problem was reported in SILVER SPRING, MD. Vehicle was purchased on June 28, 2009. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph. DEALER'S NAME: LINSAY FORD . DEALER'S CITY: WHEATON . DEALER'S STATE CODE: MD.

Ford Fusion 2010 Service Brakes, Hydraulic

Ford Fusion 2010 Service Brakes, Hydraulic Review #10317487

FORD FUSION 2010 car safety problem was reported on Aug 01, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC . ford fusion 2010 s - when the brake was depressed the car accelerated until i depressed a second time much harder. the consumer first began to notice the vehicle would intermittently not start in august. he took the vehicle to the dealer, but they were unable to duplicate the problem. the consumer insisted there was a problem and eventually, they found a technical service bulletin that addressed the issue. the problem was attributed to radio frequency intermittently corrupting the crankshaft position sensor and a new ground strip was installed. the problem seemed to be rectified. the weather stripping surrounding the rear window was loose, there was loose metal around the passenger rear wheel. *jb.Mileage was 11300 miles. Vehicle Identification Number (VIN):3FAHP0GA3AR. Ford Fusion 2010 problem was reported in SILVER SPRING, MD. Vehicle was purchased on June 28, 2009. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph. DEALER'S NAME: LINSAY FORD . DEALER'S CITY: WHEATON . DEALER'S STATE CODE: MD.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10318072

FORD FUSION 2010 car safety problem was reported on Mar 05, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . i was pulled into a parking spot in the parking lot of my gym, and the car was close to stopping, or stopped. the car accelerated, and i hit the building. when the crash was over, i looked down and my car's gear was in park. either the car was already in park, and my foot was still on the brake, or my foot was on the break, and as the car accelerated forward, my hand hit the gear, putting it in park. i have pictures demonstrating skid marks (showing the brakes were engaged). the car is a hybrid model. *tr.Vehicle was involved in a crash. 1 person(s) were injured. 0 person(s) died.Mileage was 6500 miles. Vehicle Identification Number (VIN):3FADP0L35AR. Ford Fusion 2010 problem was reported in EL PASO, TX. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 3 mph.

Ford Fusion 2010 Electrical System Instrument Panel

Ford Fusion 2010 Electrical System Instrument Panel Review #10317590

FORD FUSION 2010 car safety problem was reported on Jan 01, 1901.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM: INSTRUMENT PANEL . 2010 ford fusion center instrument panel is hard to see in daylight when shadows are cast over it. also these features are at a great arm reach. *kb .Ford Fusion 2010 problem was reported in EMILY, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Electrical System Review #10320637

FORD FUSION 2010 car safety problem was reported on Feb 26, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . my 2010 ford fusion, has a problem not notice the car not starting up. when you start the car up, so i think i start the car up. put in drive, in actually not on. *tr.Ford Fusion 2010 problem was reported in FORESTVILLE, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Electrical System Review #10320678

FORD FUSION 2010 car safety problem was reported on Mar 15, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . my 2010 ford fusion sel 6cyl. has stalled twice once during a rolling stop and the second time fully stopped. both times the car just lost all power and the electronics inside the car quit working when restarted. after turning the car off a second time and restarting again the electronics started working again. nothing has been done to fix it yet as the dealer has not heard of the complaint and will charge me a service call if they can not find the problem even though the car has only 7500 miles on it. *tr.Mileage was 7500 miles. Vehicle Identification Number (VIN):3FAHP0JG3AR. Ford Fusion 2010 problem was reported in ADRIAN, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. VEHICLE SPEED: 3 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10320775

FORD FUSION 2010 car safety problem was reported on Mar 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . my car is experiencing a problem dealing with acceleration hesitation. many times i required acceleration to take over a car by depressing the gas pedal, followed by no power response in middle of the overtaking. during these episodes the engine began oscillating crazily between rev excessively and the rpm's increased rapidly (from 7000 to 10000 rpm) and decreasing without control without not power response. in addition, the transmission exhibited a delay and a hard shift. the failure occurred intermittently. this failure put me in a high risk during thetaking over in the highway as power did not response and i almost collided twice the vehicle is in the service shop from the dealer and has not been repaired at this time. first dealer diagnostic mentioned that it was a matter of reprogramming the car's computer systems however problem remained and they retained the car for further investigation giving a second diagnostic of body valves transmission problem. ford mentioned that new body valves will be available by march the 31st, i have not date from ford and dealer when car will be totally repaired and if this is the real solution. *tr.Mileage was 5716 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in OCOTLAN, 00. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10321597

FORD FUSION 2010 car safety problem was reported on Mar 16, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . tl* the contact owns a 2010 ford fusion. while driving at speeds of 40 mph, the vehicle would not accelerate. the vehicle would exhibit transmission failures. the failure occurred on several occasions. the vehicle was taken to the dealer but there were no repairs made to the vehicle. the vin was not available when the complaint was filed. the failure and current mileages were 12,000..Mileage was 12000 miles. Ford Fusion 2010 problem was reported in ROMEO, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Latches/locks/linkages Doors Latch

Ford Fusion 2010 Latches/locks/linkages Doors Latch Review #10322345

FORD FUSION 2010 car safety problem was reported on Mar 22, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with LATCHES/LOCKS/LINKAGES:DOORS:LATCH . tl* the contact owns a 2010 ford fusion. the passenger front door could not be opened or latched from the inside of the vehicle. the vehicle had not been inspected or repaired at the time of the complaint. the vehicle identification number was not available at the time of the complaint. the failure mileage was approximately 900. the current mileage was approximately 1,100. the vin was unavailable. updated 5/6/10 *cn updated 05/10/10.Mileage was 900 miles. Ford Fusion 2010 problem was reported in PITTSBURGH, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph. DEALER'S NAME: HERTZ RENTAL . DEALER'S CITY: PHOENIX . DEALER'S STATE CODE: AZ.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10323277

FORD FUSION 2010 car safety problem was reported on Mar 29, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl*the contact owns a 2010 ford fusion. the contact was driving into a parking space at 1 mph when the vehicle suddenly lunged forward and crashed into a fenced barrier. there were no injuries but a police report was filed. the vehicle was taken to an automotive body shop but no repairs had been performed. the current and failure mileages were 1,741. .Vehicle was involved in a crash. Mileage was 1741 miles. Vehicle Identification Number (VIN):3FAHP0JG5AR. Ford Fusion 2010 problem was reported in PHILADELPHIA, PA. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 1 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10323354

FORD FUSION 2010 car safety problem was reported on Mar 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . 2010 ford fusion -- transmission slips while accelerating, sometimes getting stuck in 3 gear or so before jerkily shifting to fourth..Mileage was 20000 miles. Vehicle Identification Number (VIN):3FAHP0GA7AR. Ford Fusion 2010 problem was reported in TROY, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10323502

FORD FUSION 2010 car safety problem was reported on Feb 15, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . tl*the contact owns a 2010 ford fusion. the contact stated that the vehicle shut off when she drove over a pothole in the road prefaced by a chiming sound. the contact was driving approximately 20 mph when the failure occurred. the vehicle was taken to an authorized dealership where the contact was informed that the vehicle needed an upload for the computer system; however, the upload did not remedy the failure. the vehicle was taken to the dealer a second time but the vehicle stalled again when the contact was driving it home. the contact took the vehicle to the dealership where it remained for two weeks before it was returned. the contact was unaware of how the vehicle was repaired but stated that the failure had not occurred since it was repaired the third time. the failure mileage was approximately 10,000. the current mileage was approximately 11,300..Mileage was 10000 miles. Vehicle Identification Number (VIN):3FADP0L32AR. Ford Fusion 2010 problem was reported in SENECA, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10323642

FORD FUSION 2010 car safety problem was reported on Mar 25, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . transmission slips out of gear. *tr.Mileage was 10000 miles. Vehicle Identification Number (VIN):3FAHP0JG5AR. Ford Fusion 2010 problem was reported in MARANA, AZ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Seats

Ford Fusion 2010 Seats Review #10324793

FORD FUSION 2010 car safety problem was reported on Dec 09, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SEATS . iinformation redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6) have recently purchased a 2010 ford fusion hybrid, vin [xxx]. i love everything about the car except the front seat head restraints. they are angled too far forward and are not adjustable except for height. they force the head to bend forward, chin down, so that to look out the windshield one has to have the eyes in a "looking up" position, causing eye muscle strain. my wife has back problems and this non-adjustable design exacerbates the situation in her opinion and in her chiropractor's opinion. we think ford should provide replacement headrests that allow the upper cervical vertebrae to be aligned with the lower spine when the rider's back is in full contact with the seat back. i have enjoyed having cars in which the headrest can be pivoted to allow drivers of different builds to find a comfortable head and neck position without compromising the goal of protection against whiplash injury. please get ford motor company to replace these uncomfortable, intrusive headrests with redesigned ones! *tr.Mileage was 0 miles. Vehicle Identification Number (VIN):3FADP0L39AR. Ford Fusion 2010 problem was reported in BIG SPRING, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Air Bags

Ford Fusion 2010 Air Bags Review #10325611

FORD FUSION 2010 car safety problem was reported on Mar 10, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with AIR BAGS . i bought a ford fusion 2010, jan 6, servicetrack light stays on, did not drive. jan 8 , send to dealer, dealer said rcm(module controls airbag,etc) is not working,order rcm from ford. they replaced the rcm for the new car, and i noticed that "serviceadvansetrac " prompt user at the start,comes with a warning sound, annoy and feels very unsafe,i deal with ford but they claim it is normal!!!!!. i think that this is still problem from rcm and it controls air bag, i am very very upset about the car. *tr .Mileage was 3 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in HARRISON, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10325653

FORD FUSION 2010 car safety problem was reported on Mar 31, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . tl* the contact owns a 2010 ford fusion. the contact stated that in order to shift gears, she would have to allow the vehicle to idle for approximately eight minutes. the dealer was unable to offer a remedy for the failure. the contact confirmed she had experienced the failure on multiple occasions. the failure mileage was 9 and the current was 900. updated 05/18/2010. *lj .Mileage was 9 miles. Vehicle Identification Number (VIN):3FAHP0HA2AR. Ford Fusion 2010 problem was reported in FRIDLEY, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train Automatic Transmission Review #10325841

FORD FUSION 2010 car safety problem was reported on Apr 14, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . hard shift/clunking noise, left wheel hop then no gear (neutral) usual shifting from 2 - 3. no passing in this vehicle, will jump out of gear when shifting from 2 - 3. *tr.Mileage was 18123 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in GRAND BLANC, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 33 mph.

Ford Fusion 2010 Visibility

Ford Fusion 2010 Visibility Review #10326979

FORD FUSION 2010 car safety problem was reported on Apr 16, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY . tl*the contact owns a 2010 ford fusion. the contact stated that on april 16, 2010 while driving at approximately 55 mph, a ?pea sized stone? hit the windshield in the center near the wiper blades. the windshield initially had a ?chip? in it which expanded to a crack about 18 inches long. the vehicle had not been repaired at the time of the complaint. the contact called the manufacturer but was offered no assistance. the failure mileage was 968. the current mileage was 988. .Mileage was 968 miles. Vehicle Identification Number (VIN):3FAHP0HG8AR. Ford Fusion 2010 problem was reported in ETHAN, SD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 988 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10327597

FORD FUSION 2010 car safety problem was reported on Apr 15, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . i bought a 2010 ford fusion from shaefer ford in cumberland md on 3/17/10. on 4/15/10 i was driving on 220 south from my home in bedford to cumberland. i passed a truck and then tried to slow down and the accelerator would not respond to the brake pressure. for over 1 mile i had brake all the way to the floor and the vehicle was still going at 45 mph. i saw 4-5 cars stopped in front of me so i turned off the car and was able to steer to the shoulder and the truck passed me. i called shaeffer ford and was towed to their lot. i left the car and later that day i was told that the floor pad had hooked onto the accelerator so that it did not decelerate. they said they check everything and that everything was ok and the brakes were not damaged. i drove the car home that afternoon. *tr.Mileage was 2000 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in BEDFORD, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10328461

FORD FUSION 2010 car safety problem was reported on Apr 30, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . transmission slips and clunking noise. car goes from 1st to 2nd gear and bucks. almost got rear ended twice. also transmission slips at high speeds. *tr.Mileage was 14000 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in CENTER VALLEY, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Exterior Lighting

Ford Fusion 2010 Exterior Lighting Review #10329102

FORD FUSION 2010 car safety problem was reported on Apr 24, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with EXTERIOR LIGHTING . 2010 ford fusion se, head lights and dash board lights are on at all times but the tail lights are not, this model does not have automatic on switch. first night i drove the car a neighbor told me i had no tail lights, i had strong running lights that i was driving by that i though were automatically switched head lights. my husband drove the car and assumed the same. we did figure it out. on 4/24 i was issued a warning for no tail lights. i spoke to other owners and they too have been pulled over for no taillights. also was following a fusion last week that did not have tail lights. this is dangerous, the tail lights should be part of the running light circuit or the running lights should not be sufficient to drive by. i just wanted to be on the record before i get rear ended at dusk after i realize that i have not turned on my tail lights. *tr.Mileage was 20 miles. Vehicle Identification Number (VIN):3FAHP0HA4AR. Ford Fusion 2010 problem was reported in LAKELAND, FM. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10329129

FORD FUSION 2010 car safety problem was reported on Apr 19, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . tl* the contact owns a 2010 ford fusion sel. while driving approximately 45 mph on a hill, the transmission failed and the contact was unable to change gears. the vehicle was towed to the dealer where the contact was advised that the transmission would need to be replaced. the failure and current mileages were 6,005. .Mileage was 6005 miles. Vehicle Identification Number (VIN):3FAHP0JA4AR. Ford Fusion 2010 problem was reported in RESIDENTIAL, NM. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10329285

FORD FUSION 2010 car safety problem was reported on Mar 06, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . transmission slips and loud bumping noise. car goes from 1st to 2nd gear and jerks. transmission slips between 60-70mph. i was almost t-boned!!!! *tr.Ford Fusion 2010 problem was reported in TALKING ROCK, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Latches/locks/linkages

Ford Fusion 2010 Latches/locks/linkages Review #10329489

FORD FUSION 2010 car safety problem was reported on May 08, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with LATCHES/LOCKS/LINKAGES . i own a 2010 ford fusion hybrid with 7,722 miles. yesterday, while traveling on the interstate (in sd) at 80 mph, the right front door spontaneously opened. (there seemed to be a safety latch similar to one on the hood of a car, so it popped open and the interior "lock/unlock" switches opened but the door itself did not open any distance.) we checked the lock mechanism and also tried to recall if we could have done anything to cause the door to open but could find/recall nothing. *tr.Mileage was 7722 miles. Vehicle Identification Number (VIN):3FADP0L36AR. Ford Fusion 2010 problem was reported in CHEVY CHASE, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 80 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10329546

FORD FUSION 2010 car safety problem was reported on Apr 17, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . transmission slips . makes loud banging noise. first occurred with 750 miles on car. car taken in for service, was told "module" was replaced, not so. they have thus far refused to provide documentation as to what they did. same thing happened again 4 days later. again took in for service, this time i was told "computer" was replace, once again not so. he have so far refused to provide documentation as to what was done. same thing again again about 1 week later. 1035 miles. car now at dealer for repairs, there now for 7 days ?? *tr.Mileage was 750 miles. Vehicle Identification Number (VIN):3FAHP0HA2AR. Ford Fusion 2010 problem was reported in PALMERTON, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10331488

FORD FUSION 2010 car safety problem was reported on May 19, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . when driving the automatic transmission sometimes slips out of gear and goes to neutral. this problem happens from 10-40mph at 0-50% throttle. loss of power happens between 5-10 seconds and the engine rpms will increase to 7,000 rpms. depressing the throttle allows the transmission to engage again with an abrupt and hard shift. accelerating again after this is very slow and sluggish and is believed that the car is in an upper gear. almost caused a wreck that could have ended my life between two tractor trailers because of loss of power and failure to accelerate. *tr.Mileage was 14000 miles. Vehicle Identification Number (VIN):3FAHP0HA4AR. Ford Fusion 2010 problem was reported in HUMBLE, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10332233

FORD FUSION 2010 car safety problem was reported on Apr 16, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . several weeks before the incident, i removed the driver's side all-weather floor mat (the factory-developed optional one) from our 2010 ford fusion hybrid and tossed it in the trunk. in the days leading up to this incident, the car had been to the body shop and the car wash. as near as i can tell an attendant at one of those places must have discovered the mat in the trunk and "helpfully" reinstalled it. but i didn't notice this right away. when commuting to work on april 16th, i pressed the accelerator to the floor as i moved into a much faster traffic lane. upon completion of this maneuver i eased up on the gas, but the pedal stayed down and the car kept accelerating, unintentionally at this point. at first i wasn't sure what was going on, but after about 3 or 4 seconds i heard a "click", the pedal returned to normal and the car slowed. it was then that i thought of the all-weather floor mat, and when traffic cleared i tried another experimental full-throttle dab to see if i was correct. it happened again (but i was ready for it), with the pedal releasing on its own after a few seconds, just like before. at this point i was careful not to disturb the mat's position so i could take video of the problem once i arrived at work. once in the garage, and with the engine off, i was able to replicate the floor mat-throttle interference on-camera. as before, the pedal stayed stuck for about 3 seconds after i pressed it to the floor. i was able to repeat this several times. but in one trial the stuck throttle persisted for over 30 seconds, with the pedal staying stuck despite vigorous stamping in an effort to free it. the only way it came loose was by lifting my heel which, in the normal driving posture, had apparently been pinning the mat down and making it less flexible. with the heel pressure removed, the mat bent up out of the way and the pedal began a slow return. a you tube video link is available upon request. *tr.Mileage was 4525 miles. Vehicle Identification Number (VIN):3FADP0L32AR. Ford Fusion 2010 problem was reported in YORBA LINDA, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10332584

FORD FUSION 2010 car safety problem was reported on May 14, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . 2010 ford fusion transmission slipped on highway at 70 miles per hour. rpm's increased, loss of speed - had to exit freeway across traffic at a very low speed - was afraid the car was going to stall. ford roadside assistance towed vehicle to briarwood ford in saline - waiting for repairs. requested new transmission vs. repair - ford not complying. vehicle had just been at suburban ford in waterford for oil change and "recall" on transmission celluloid issue 6 days prior. was told that it checked out fine. *tr.Mileage was 15863 miles. Vehicle Identification Number (VIN):3FAHP0JG3AR. Ford Fusion 2010 problem was reported in WHITE LAKE, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10334010

FORD FUSION 2010 car safety problem was reported on May 26, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . tl* the contact owns a 2010 ford fusion. the contact stated that his vehicle was serviced at an authorized dealer for an unknown transmission repair. afterward, whenever he would release his foot from the accelerator pedal, the vehicle would down shift and the failure would recur at any traveled speed. the dealer informed the contact that they had recalibrated the power control module in accordance with a new federal regulation. the vehicle was not further repaired and the failure continued to recur. the failure mileage was 1,500 and the current mileage was 1,900. .Mileage was 1500 miles. Vehicle Identification Number (VIN):3FAHP0JGXAR. Ford Fusion 2010 problem was reported in HAZEL PARK, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Structure

Ford Fusion 2010 Structure Review #10334123

FORD FUSION 2010 car safety problem was reported on Oct 31, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE . safety issue. design/engineering defect. 2010 fusion hybrid. foot space between the knee airbag housing and brake pedal is severely and dangerously restricted by the physical presence, bulk, and location of the knee airbag. this delays response for instant brake deployment for emergency deceleration. vertical clearance is ~4" and is less if approached at an angle, swiveling on heel from accelerator to brake. lifting foot with leg from hip bumps foot against airbag housing, stopping smooth transition to pedal with either foot. foot then must slide horizontally into narrow space to engage brakes. foot space is dangerously restricted even with driving mocs. i have excellent reflexes and 60-year safe driving record with no moving violations. but in congested freeway conditions during a 3600-mile road trip i felt required to drive with left foot poised above the brake pedal to limit emergency response time. with only short trips for 1500 miles, i at first thought i might get used to this problem. this limitation and the extraordinary driving practices required for safety only became painfully apparent during the road trip. this safety issue was reported to ford motor company today. desire physical removal of knee airbag with all mounting hardware and reprogramming of software to ignore its absence. note: the required "incident date" on this form is the approximate date of manufacture, listed on the rocker panel as 10/09. this is an engineering design defect which appears to have been an afterthought. no accident has resulted only because i have devoted assiduous attention to mitigating the problem by shoe choice and extremely careful driving practice. *tr.Mileage was 0 miles. Vehicle Identification Number (VIN):3FADP0L35AR. Ford Fusion 2010 problem was reported in SPOKANE, WA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10334127

FORD FUSION 2010 car safety problem was reported on May 25, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . i was driving a ford fusion that i had rented from hertz in minot, north dakota. i was pulling out of the parking space and luckily had my foot on the brake when the car suddenly accelerated. i had to push down very hard on the brake pedal to keep the car under control. i immediately put the car in "park" and the acceleration slowed down. i drove the car that day but reported the incident to hertz and urged them to get the car checked. the ford fusion had less than 3000 miles on the odometer so i assume that it was a 2010 model. *tr.Mileage was 2574 miles. Ford Fusion 2010 problem was reported in HOUSTON, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Visibility

Ford Fusion 2010 Visibility Review #10334141

FORD FUSION 2010 car safety problem was reported on May 27, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY . while driving our brand new ford fusion sedan se on the freeway around 2pm. i was far away from cars and i don't drive near semi's or dump trucks i heard a noise in the windshield frame on the passenger side mid way up and then a horizontal crack approx 14 inches appeared. i got off the next exit and called our dealer immediately and they said bring into service dept 7am next morning. the service dept looked at windshield and frame and stated it was a microscopic chip. we had to pay almost $400 for a new windshield and we still think it was a defective windshield. it was at approx 1,000 miles. it's interesting and concerning a friend of ours bought a ford fusion s at the same dealer over a month ago and after 2 weeks his windshield did the same thing. we'd appreciate you checking into this. i spoke with the business manager at the dealer the day it happened and he said maybe it's the heat. i had 2 of the windows down partially in the back. where's the quality checks they make. thank you. *tr.Mileage was 1000 miles. Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in COLUMBUS, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Equipment

Ford Fusion 2010 Equipment Review #10334211

FORD FUSION 2010 car safety problem was reported on Mar 14, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with EQUIPMENT . 2010 ford fusion hybrid. floor mat as installed at dealer jammed against accelerator. driver was able to stop the vehicle and correct the problem by unstacking deep weather floor mats from regular floor mat. *tr.Mileage was 8000 miles. Vehicle Identification Number (VIN):3FADP0L33AR. Ford Fusion 2010 problem was reported in LUBEC, ME. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10334376

FORD FUSION 2010 car safety problem was reported on May 31, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . i have a ford fusion 2010. i first noticed my car had an issue in april. i was behind a truck and it was slowing down so i stepped on the brake. i took my foot off the brake and the car accelerated by itself. i was in ky over the weekend and noticed the car speeding up into passing gear after i stepped on the brake. i get home from ky and find a recall for a transmission issue. i did not report the problems i was having to the dealer because i saw what the media did to owners of toyotas saying that their foot slipped off the brake and on to the gas. i took the car to the dealer for the recall issue this past tuesday. it was noted i was the first to report that the car accelerated by itself. im not sure if i fall into the stupid category or not but i did notice in the paper yesterday that floor mats maybe causing the accelerating issue. who ever said this is really the stupid one. and please do not blame this on driving habits im averaging 25.1 miles per gallon. do i trust my car with only 4100 miles on it? would you? *tr.Mileage was 4100 miles. Vehicle Identification Number (VIN):3FAHP0JGXAR. Ford Fusion 2010 problem was reported in PLEASANT GARDEN, NC. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10334467

FORD FUSION 2010 car safety problem was reported on Sept 01, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . tl* the contact owns a 2010 ford fusion. the contact stated the engine would intermittently stall without warning and lose all power. the dealer performed diagnostic testing and found the air filter was not properly installed and was causing the vehicle to stall. the failure persisted. the vehicle was taken back to the dealer where they were unable to duplicate the failure. the manufacturer advised there could be no repairs made to the vehicle until the failure was able to be diagnosed. the vehicle was not repaired. the failure mileage was approximately 900 and the current mileage was approximately 14,000. updated10/27/10.*lj .Mileage was 900 miles. Vehicle Identification Number (VIN):3FAHP0JA1AR. Ford Fusion 2010 problem was reported in HEBRON, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Engine And Engine Cooling Review #10334937

FORD FUSION 2010 car safety problem was reported on June 06, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . i own a 2010 ford fusion hybrid. i was pulling my car into my garage to park it. i had slowed my car down very slowly before i pulled into my driveway. the car was "idling" into the driveway. about 5 feet from the wall and 2 feet from where i usually stop, the accelerator slowly pulled down toward the floor. it took me one or two seconds to realize what was happening. during that time, my car moved head on toward the garage wall. i pressed on the brake and the car stopped. the car had already slammed straight into the wall of my garage. my toddler was in the backseat of the car and started crying. i was shocked by what had happened. i loved that car and always believed that it was the perfect car. now, i have damage to the car and to my house. most importantly, the car spontaneously accelerated and a person could have been caught between my car and that garage. i was going to go to a popular grocery store in my neighborhood that day. but, i decided not to do so because my toddler was looking sleepy. if i had gone to the store, i could have run a shopper over with my out-of-control car. i called the dealership who sold me the car immediately. they did not call me back. *tr.Vehicle was involved in a crash. Vehicle Identification Number (VIN):3FADP0L33AR. Ford Fusion 2010 problem was reported in FULLERTON, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 5 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10335090

FORD FUSION 2010 car safety problem was reported on June 03, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl*the contact owns a 2010 ford fusion. while stopped with her foot on the brake, the contact stated that the vehicle attempted to surge forward. the contact applied heavy pressure to the brake to keep the vehicle from moving while it attempted to surge forward three times. once the engine stopped revving, the contact attempted to accelerate but the vehicle would only move very slowly. the service engine light illuminated on the instrument panel so the contact pulled over and shut off the vehicle. upon restart the vehicle operated as normal and was towed to an authorized dealership where the contact was told there was nothing wrong with the vehicle. the failure and current mileages were approximately 1,100. .Mileage was 1100 miles. Vehicle Identification Number (VIN):3FAHP0HG4AR. Ford Fusion 2010 problem was reported in TROY, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10335125

FORD FUSION 2010 car safety problem was reported on Jan 04, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . vehicle shifts unusually between 2nd & 3rd gear and 3rd & 4th gear. the condition is worse in wet and/or cold weather. on top of the regular malfunction of the gear shifting, on three separate occasions the vehicle has slammed between gears creating a "rear end crash type feel" to the passengers inside the vehicle. the dealership claims that the car shifts properly in comparison to "like" vehicles which makes the unusual shifting condition "normal" to the 2010 ford fusion. *tr.Mileage was 150 miles. Vehicle Identification Number (VIN):3FAHP0HG5AR. Ford Fusion 2010 problem was reported in BEAVERTON, OR. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10336813

FORD FUSION 2010 car safety problem was reported on June 16, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. while driving in extremely heavy traffic approximately between 3-4 mph, an unexpected increase of acceleration occurred. the contact applied pressure to the brake pedal and the vehicle continued to accelerate which caused the vehicle to crash into the proceeding vehicle. there was no personal injury or damage to the vehicle. a police report was not filed. the authorized dealer was notified of the acceleration failure. the contact stated the vehicle would be taken to the authorized dealer for diagnosis. the failure mileage was 960. updated 07/12/10*jb.Vehicle was involved in a crash. Mileage was 960 miles. Ford Fusion 2010 problem was reported in STAMFORD, CT. Vehicle was purchased on May 20, 2010. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 3 mph.

Ford Fusion 2010 Visibility Windshield

Ford Fusion 2010 Visibility Windshield Review #10339288

FORD FUSION 2010 car safety problem was reported on June 19, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:WINDSHIELD . on june 19, 2010 a large crack developed in my windshield of my 10 month-old 2010 fusion hybrid. no foreign object struck it. a ford dealership is attempting to attribute the crack to a foreign object with no objective explanation. the crack continued to grow across the entire windshield making the vehicle unsafe to operate. *tr.Mileage was 14912 miles. Vehicle Identification Number (VIN):3FADP0L31AR. Ford Fusion 2010 problem was reported in CHARLOTTE, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Steering

Ford Fusion 2010 Steering Review #10339693

FORD FUSION 2010 car safety problem was reported on Mar 14, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with STEERING . tl* the contact owns a 2010 ford fusion. the contact stated when applying the brakes from any speed, the steering wheel would slightly turn to the right. the vehicle was not diagnosed and the contact stated he noticed that failure since purchasing the vehicle. the current and failure mileages were 1,300. updated 08/11/10. *lj the consumer stated the vehicle would pull to the left or right when coming to a stop. updated 08/17/10*jb .Mileage was 1300 miles. Vehicle Identification Number (VIN):3FAHP0HG5AR. Ford Fusion 2010 problem was reported in SHREWSBURY, MA. Original Owner. Vehicle was purchased on Feb 26, 2010. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: BIFUEL. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 5 mph. DEALER'S NAME: HERB CHAMBERS FORD . DEALER'S TELEPHONE NUMBER: 508-366-8311 . DEALER'S CITY: WESTBOROUGH . DEALER'S STATE CODE: MA. DEALER'S ZIPCODE: 01581 .

Ford Fusion 2010 Seats

Ford Fusion 2010 Seats Review #10339936

FORD FUSION 2010 car safety problem was reported on June 24, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SEATS . i just bought a 2010 ford fusion. i know now why they only allow you to test drive these cars around the block. the first time i drove it, i got a burning pain down my neck and a piercing headache. the headrest is a wedge with the greatest protrusion hitting the greatest protrusion of the back of your head. no adjustment of the seat or headrest helps. i tried to return the car immediately, but they refused. this weird angle puts your chin down on your chest and your sight line in a hazardous alignment. if there were a wreck, the angle would cause your neck to snap. ford is aware of this, apparently, and has received many complaints, yet does nothing. people are resorting to turning the headrest around, which will not protect against whiplash, or having it bent in a vise, which could allow it to break in a collision. all the fords now have this dangerous torture device, so you cannot change them. help! *tr.Mileage was 70 miles. Vehicle Identification Number (VIN):3FAHP0HG0AR. Ford Fusion 2010 problem was reported in RALEIGH, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10339980

FORD FUSION 2010 car safety problem was reported on June 24, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact lightly depressed the accelerator pedal from a complete stop when the vehicle abnormally accelerated at a rapid rate of speed. she was able to stop the unintended acceleration by applying the brakes and moved the vehicle off the roadway. the vehicle was towed to the dealer where the contact was awaiting a diagnosis of the failure. the failure and current mileage was 8,000. updated 08/11/10. *lj updated 08/17/10*jb.Mileage was 8000 miles. Vehicle Identification Number (VIN):3FAHP0HG2AR. Ford Fusion 2010 problem was reported in BATAVIA, IL. Original Owner. Vehicle was purchased on Aug 14, 2009. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 2 mph. DEALER'S NAME: GJOVIK FORD MECURY . DEALER'S CITY: SANDWICH . DEALER'S STATE CODE: IL. DEALER'S ZIPCODE: 60548 .

Ford Fusion 2010 Seats

Ford Fusion 2010 Seats Review #10340920

FORD FUSION 2010 car safety problem was reported on June 30, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SEATS . the 2010 ford fusion has poorly designed driver/passenger head restraints. i, of height 5'7", test drove one yesterday, and got no further than 0.25 miles before needing to park. the headrest is angled forward, causing excessive neck strain, and there is no way to adjust its tilt to a more vertical position. i did subsequently complete the test drive, albeit with frequent bodily adjustments. driving this vehicle with proper posture is impossible with these head restraint design. ps: the link below for emailing the nhtsa is broken. http://www.nhtsa.gov/nhtsa-dpmextn/jsp/email/email_nhtsa.jsp. *tr.Ford Fusion 2010 problem was reported in SUNNYVALE, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10342296

FORD FUSION 2010 car safety problem was reported on June 08, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl*the contact owns a 2010 ford fusion. the contact stated that while driving 65 mph with the cruise control engaged down hill it would not adjust the speed; yet, the rpms increased to 4000 while the engine made a high pitch screaming noise. the vehicle was taken to the dealer to have the software repaired; however, it would not solve the problem. the manufacturer was contacted and stated that it must be a characteristic of the vehicle and they don't know how to repair the failure. the failure and current mileages were 13,000. updated 10/21/10. *lj the consumer stated instead of slowing the engine down to maintain speed when going down a steep grade, it revs really high. a service technician stated there was definitely something wrong, but there was no fix for it. updated 10/26/10.Mileage was 13000 miles. Vehicle Identification Number (VIN):3FAHP0HA9AR. Ford Fusion 2010 problem was reported in LINDLEY, NY. Vehicle was purchased on Aug 15, 2009. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 65 mph. DEALER'S NAME: WESTHERRFORD . DEALER'S TELEPHONE NUMBER: 888-298-2246 . DEALER'S CITY: HAMBURG . DEALER'S STATE CODE: NY.

Ford Fusion 2010 Seats Front Assembly Head Restraint

Ford Fusion 2010 Seats Front Assembly Head Restraint Review #10342590

FORD FUSION 2010 car safety problem was reported on Mar 19, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SEATS:FRONT ASSEMBLY:HEAD RESTRAINT . tl*the contact owns a 2010 ford fusion s. the contact stated that when the headrest were in their proper forward position, they would push the passengers heads forward and cause him to lean forward. the head rests were turned backwards to alleviate the pressure. the dealer advised the contact that they were unable to provide any assistance or repair the vehicle in order to correct the design of the headrest. the manufacturer was not contacted. the failure mileage was approximately 100 and the current mileage was approximately 7,000. updated 09/16-10 *bf updated 09/20/10*jb .0 person(s) were injured. 0 person(s) died.Mileage was 100 miles. Vehicle Identification Number (VIN):3FAHP0GA5AR. Ford Fusion 2010 problem was reported in TOMS RIVER, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS.

Ford Fusion 2010 Seats Review #10342735

FORD FUSION 2010 car safety problem was reported on July 12, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SEATS . 2010 ford fusion head rests really hurt the neck and shoulders after any period of driving. ford needs to replace with better ergo head rests. *tr.Ford Fusion 2010 problem was reported in HARKER HEIGHTS, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10343636

FORD FUSION 2010 car safety problem was reported on Mar 16, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact stated when depressing the accelerator pedal, there was an abnormal increase in engine rpms. the vehicle would sporadically accelerate at a rapid pace. the failure would persist even after the contact would remove her foot from the accelerator pedal. the dealer contacted the manufacturer who advised him not to make any repairs to the vehicle. the manufacturer advised that after sixty days, the vehicle should correct itself. the vehicle was not repaired. the failure mileage was 1,200 and the current was unknown. .Mileage was 1200 miles. Vehicle Identification Number (VIN):3FAHP0JA6AR. Ford Fusion 2010 problem was reported in THE VILLAGES, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10343821

FORD FUSION 2010 car safety problem was reported on May 20, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . after the car has been unused for 2 or more days, the transmission evidences an engine flair where the gears are disengaged, followed by a very hard shift between 2nd and 3rd gears. sometimes it also flares between 4th and 5th. this is a safety issue on left turns and when merging into traffic. *tr.Mileage was 2300 miles. Vehicle Identification Number (VIN):3FAHP0HGXAR. Ford Fusion 2010 problem was reported in GREENWOOD, DE. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10344087

FORD FUSION 2010 car safety problem was reported on June 10, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . i have a 2010 ford fusion which was recalled for the transmission problems. i brought it in for the hard shifts and when put into drive it feels as if the transmission is going to fall out of the front end. they keep telling me nothing is wrong with the car. this is crazy seeing this is a new vehicle with only 5,000 miles on it. *tr.Mileage was 2500 miles. Vehicle Identification Number (VIN):3FAHP0JA0AR. Ford Fusion 2010 problem was reported in SCOTT TOWNSHIP, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Power Train Automatic Transmission Control Module (tcm, Pcm)

Ford Fusion 2010 Power Train Automatic Transmission Control Module (tcm, Pcm) Review #10344284

FORD FUSION 2010 car safety problem was reported on Apr 15, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM, PCM) . tl*the contact owns a 2010 ford fusion. while driving approximately 30 mph the contact stated that the vehicle began to shift hard. he stated that the transmission slips, and at times when he engaged the accelerator pedal it hesitated. the vehicle was taken to an authorized dealer who reprogrammed the pcm. the contact stated that the failure occurred again and the dealer replaced the value body. he stated that the failure occurred three times. the vehicle was taken to the dealer when the complaint was filed. the approximate failure mileage was 7,200 and the current mileage was 8,300. .Mileage was 7200 miles. Vehicle Identification Number (VIN):3FAHP0GA8AR. Ford Fusion 2010 problem was reported in WALDORF, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10345112

FORD FUSION 2010 car safety problem was reported on July 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . in yellowstone national park, i was driving north from canyon village to tower falls. a sign said, "7% downgrade 6 miles all vehicles use lower gear". the ford fusion se v6 with automatic gives the choice of first, which redlines at about 35 mph, or drive, which will shift to 6th gear even on the level at 35mph. i had to ride the brakes for the next six miles. at the bottom of the hill is a pedestrian crossing and a speed limit of 15 mph. i pulled off to the parking lot at tower falls and the smell of hot brakes was everywhere. the vehicle's wheels were hot. if the brakes had faded, i would have hit the pedestrian crossing at high speed unless i found a nice rock wall to run into instead. the vehicle desperately needs engine braking. the engine ran at about 1,000 rpm all the way down the mountain. it idles at about 500 rpm when hot, so the engine braking was nearly nonexistent. *tr.Ford Fusion 2010 problem was reported in CEDAR RAPIDS, IA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10345179

FORD FUSION 2010 car safety problem was reported on July 06, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . transmission on 2010 ford fusion skips out of gear and clunks into gear at times. failed to go into gear when i was pulling out onto a busy highway. i had to pull off the road to avoid being hit by the car from behind.near accident. ford earlier issued a recall on the transmission and re- calibrated the powertrain module. this obviously did not work because of the ensuing accident. i took it back to the dealer and they could find nothing wrong with it. this was in june of 2010. by july, it was worse and i took it back again. this time they kept the car. they said they would take the transmission apart and get instructions from ford headquarters. when i checked the internet, i found page after page of complaints by fusion 2010 owners with the similar transmission problems. some, l occur after 7-10 months(12,000 miles) and some much sooner. i am concerned that it will be fixed properly because some owners received re-built transmissions and some received new transmissions, and these fixes did not always work according to owner testimony. my car has been in the shop for well over a week already. all i want is my car back without any transmission problems. let's hope nobody gets in a serious accident because of this condition. my complaint is with ford headquarters, not the dealer. the dealer is not in control. *tr.Mileage was 14000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in AVON, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10345322

FORD FUSION 2010 car safety problem was reported on July 15, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . my wife's 2010 ford fusion sel has 14000 miles and the transmission began to slip. so much so, she feared for her life on the washington, dc suburban streets she drives. the car would not shift into low gear causing several "almost accidents" with other drivers almost rear-ending her in traffic. we took the car into koons sterling ford in sterling, va on 16 february. we were told that it was an issue and that our car would be there for several days. they claimed that "ford does not allow them to put in a new or rebuilt transmission" but that they were going to "tear the transmission down and replace bands and clutches" in my new car. i contacted ford corporate who said they would be putting a rebuilt transmission in my car. that did not sound correct to me because they will have had it for most of two weeks - i conferred with the dealer who confirmed that they were rebuilding my transmission from scratch (bands and clutches). i called ford back and they apologized for the misinformation they gave me. ford is clueless as to what the problem is, much less how to fix it. i consider this as much of an issue as the toyota acceleration problem. when a new car scares your wife, there is something wrong. this car was motor trend's "car of the year..." *tr.Mileage was 14000 miles. Vehicle Identification Number (VIN):3FAHP0CG6AR. Ford Fusion 2010 problem was reported in STERLING, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10345830

FORD FUSION 2010 car safety problem was reported on July 27, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact stated while driving at 45 mph, the vehicle abnormally accelerated up to 85 mph. the contact was unable to stop the unintended acceleration by depressing the brake pedal. he then shifted into neutral and applied extreme force to the brake pedal before the vehicle came to a stop. the contact stated as the vehicle was coming to a stop, there was an abnormal increase in engine rpms. he also noticed the floor mats were holding down the accelerator pedal. the contact stated the floor mat was purchased as an aftermarket floor mat. he removed the floor mats and contacted the manufacturer who advised that the failure would not have occurred if the floor mat was purchased from the manufacturer. the contact stated there was no information in the owner's manual pertaining to proper floor mat usage. the failure and current mileages were 250. updated 10/20/10 *bf updated 10/21/10*jb.Mileage was 250 miles. Vehicle Identification Number (VIN):3FAHP0CG7AR. Ford Fusion 2010 problem was reported in BLAIRSVILLE, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: BIFUEL. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10346249

FORD FUSION 2010 car safety problem was reported on Apr 03, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . i purchased a 2010 ford fusion in august of 2009. the car always shifted out of park and into gear very hard, especially after sitting for several hours. i thought nothing of it. then the transmission began to "flare" between gear shifts. essentially the car would shift out of gear (into neutral) and then hard shift into the next gear. a ford engineer gave me the term they use "flaring". ford reflashed the transmission without resolving the problem and then reflashed it again without resolving the problem. this is a safety issue. *tr.Mileage was 10000 miles. Vehicle Identification Number (VIN):3FAHP0JA3AR. Ford Fusion 2010 problem was reported in SOUTH LYON, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10346489

FORD FUSION 2010 car safety problem was reported on July 13, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . i own a 2010 ford fusion se v4, the car is having transmission problem and not fixed even after it was at the dealership for 2 weeks. after all the arguments i manage to get the rental car (focus) for only 5 days. i wrote letter to both company and the dealership but i don't know how serious they are taking this matter. please have them replace the transmission or fix the problem asap before car breaks down in middle of no where and somebody ends up getting hurt. thank you *tr.Mileage was 4989 miles. Vehicle Identification Number (VIN):3FAHP0HAXAR. Ford Fusion 2010 problem was reported in ROCHESTER HILLS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Fuel System, Gasoline

Ford Fusion 2010 Fuel System, Gasoline Review #10346883

FORD FUSION 2010 car safety problem was reported on July 29, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE . tl* the contact owns a 2010 ford fusion. the vehicle was equipped with a cap less fuel tank. the contact observed whenever dispensing fuel into the fuel tank to the full capacity, the automatic shut off would not function and fuel continued to spill out of the filler neck onto the ground. the vehicle had not been inspected at the time of the complaint. the contact had significant t concern of the potential safety hazard. the failure mileage was 3,600. .Mileage was 3600 miles. Vehicle Identification Number (VIN):3FAHP0KC5AR. Ford Fusion 2010 problem was reported in REDLAND, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10347961

FORD FUSION 2010 car safety problem was reported on Aug 07, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . car had not been driven for one week. experienced a jerky transmission shift, most severely when accelerating to about 35, then letting off the gas to maintain speed. feels like the transmission shift for not good reason, and the engine jerks. *tr.Mileage was 7600 miles. Vehicle Identification Number (VIN):3FAHP0JA0AR. Ford Fusion 2010 problem was reported in QUAKERTOWN, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10348327

FORD FUSION 2010 car safety problem was reported on Aug 06, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . transmission was reprogrammed at a ford dealership. a week later, the transmission exhibited periods of not wanting to engage and when it did the car would lunge forward. you could step on the gas pedal and your engine rpm's would increase but you would just sit there, not moving then suddenly the car will lunge forward. there are also instances where when slowing down for a stop sign the car would start to jerk. it's a dangerous situation since there were other cars at the intersection when the car decided to lunge forward after applying pressure to the accelerator and having the transmission not engage immediately. it occurs after the transmission is at full operating temperature. it is currently sitting at a dealership awaiting diagnosis and repair. *tr.Mileage was 16458 miles. Ford Fusion 2010 problem was reported in OSCEOLA, IA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10349037

FORD FUSION 2010 car safety problem was reported on July 20, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . i believe i was sold a defective 2010 ford fusion. i believe the transmission wa faulty and they knew about it. the car was slow to shift bolted when put into reverse. the car was recalled. *tr.Mileage was 15783 miles. Vehicle Identification Number (VIN):3FAHP0HA9AR. Ford Fusion 2010 problem was reported in AUBURN, WA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 2 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10349981

FORD FUSION 2010 car safety problem was reported on May 19, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . 2010 ford fusion 4 cylinder, 6 speed automatic transmission. problem: automatic transmission. engine speeds-up, between up-shifts 3-4 and 4-5. problem started within 1st week of ownership. vehicle has been in for transmission related problems 2-times, waiting to schedule 3rd. all 3000 miles or less. *tr.Mileage was 1900 miles. Vehicle Identification Number (VIN):3FAHP0HA9AR. Ford Fusion 2010 problem was reported in OWENSBORO, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Visibility Windshield

Ford Fusion 2010 Visibility Windshield Review #10350009

FORD FUSION 2010 car safety problem was reported on Aug 17, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:WINDSHIELD . cracked windshield. *tr.Mileage was 1600 miles. Vehicle Identification Number (VIN):3FAHP0KC2AR. Ford Fusion 2010 problem was reported in EDGEWATER, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Service Brakes, Hydraulic

Ford Fusion 2010 Service Brakes, Hydraulic Review #10350026

FORD FUSION 2010 car safety problem was reported on Aug 14, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC . i was traveling from ca to nv in my 2010 ford fusion hybrid. i drove to minden, nv to go to a store and after leaving the store i noticed that all of my braking lights were on the dashboard. i pulled over into a parking lot and proceeded to turn the car on and off to see if it would reset something, it did not. i contacted a dealership in carson city and told them that i was having the problem, they said that they could not help me, i reiterated the problem and said that i was from out of town and that i needed the car looked at immediately. they conceded to let me come in. i drove in and then said the car would have to wait until monday when they could have a certified hybrid mechanic look at it. monday the mechanic looked at it and by that time the lights were off. they ran a diagnostic and saw that there was an error. they cleared the error and then drove the car around. they called me to say that the car was ready. they went to move the car from the bay and the lights came on again. they finally determined that the connector at the vac pump was not plugged all the way in and they then reconnected it. the car is now working fine. *tr.Mileage was 11646 miles. Vehicle Identification Number (VIN):3FADP0L34AR. Ford Fusion 2010 problem was reported in MORGAN HILL, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 25 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10351655

FORD FUSION 2010 car safety problem was reported on Mar 10, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . incident: 2010 ford fusion, 4 cyl, 6 spd auto. vehicle experiencing harsh shifting at low speeds or initially shifting into gear. violent shifting when accelerating to enter a highway. high rpms when resuming the 60 mph set cruise control speed from 35 mph, the transmission cannot seem to finally shift into 6 spd. the vehicle computer has been reset by ford service and the problem has gotten worse. the car is again being looked at by ford. service manager commented that the computer remedy might not work if not done prior to 7000 miles. why then has ford waited to inform owners about their known transmission problem? ford needs to take responsibility and work with the transmission supplier to remedy and replace the defective transmissions. transmission breakdowns will become move prevalent as more of these highly touted vehicles are sold and driven if ford doesn't own up to the problem. please intercede on behalf of consumers that own these vehicles and have had no luck with ford fixing the problematic transmission. i presently have 13000+ miles on the car and purchased it to provide safe transportation and ford assured me it could be recreational towed with no problems as long as the manual instructions were followed. updated 09/23/10 *bf the consumer stated since filing the complaint, the transmission in his vehicle was totally destroyed. the damage occurred while the vehicle was being towed. updated ivoq 09/24/10 *tr.Mileage was 7900 miles. Vehicle Identification Number (VIN):CARATDEA0LE. Ford Fusion 2010 problem was reported in LAKE WALES, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10352211

FORD FUSION 2010 car safety problem was reported on Aug 25, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . my car went to a ford dealership back in april of 2010 to have recall 10b15 (powertrain control module reprogramming) performed. ever since the recall has been performed the car is experiencing a problem with a pause in acceleration around 25 mph. whenever i am driving at or just around 25 mph in city driving conditions the car will experience a long delay between the time i push the gas pedal and the time it actually takes the car to move forward. there have been several occurrences where i have almost been rear ended due to my car not moving forward immediately like it is suppose to during normal gas pedal operation. my car was taken back to the same dealership regarding this problem and after test driving they said the car was working properly at this time. i wish a recall would be forced upon ford to remedy this problem before someone gets injured or killed! *tr.Mileage was 6700 miles. Vehicle Identification Number (VIN):3FAHP0JG1AR. Ford Fusion 2010 problem was reported in BEVERLY HILLS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 25 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10352701

FORD FUSION 2010 car safety problem was reported on Aug 28, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl*the contact owns a 2010 ford fusion sel. the contact stated that when attempting to apply the brakes to park, the vehicle surged forward over two curbs, hit a fence, and continued to accelerate through a field. the air bags did not deploy. there were no injuries. a police report was filed. the contact had not spoken with the manufacturer. the current and failure mileages were approximately 600. updated 12/7/10 *cn.Vehicle was involved in a crash. Mileage was 600 miles. Vehicle Identification Number (VIN):3FAHP0JA3AR. Ford Fusion 2010 problem was reported in DALLAS, TX. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10353716

FORD FUSION 2010 car safety problem was reported on May 14, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . tl*the contact owns a 2010 ford fusion. the contact stated that while driving at freeway speeds the vehicle would shift out of gear, making the vehicle coast as if it were in neutral then it would lock into third gear making the rpm's increase and the vehicle accelerate. the failure occurred four times. the dealer stated that the service manager test drove the vehicle; however, there were no codes and the service manager determined that there was nothing wrong with the vehicle. the failure happened again and the contact stated the dealer determined that it was a main computer failure, which was repaired. (pcm reprogram) on september 1, 2010, the failure happened again and the vehicle was taken back to the dealer while it was locked into third gear. the mechanic found an abs code and a coolant refrigerator code. he drove the vehicle 20 miles and again stated that there was nothing wrong with the vehicle that would cause the failure. the failure happened again the same day. the wrench light was illuminated and the vehicle was taken back to the dealer. the vehicle was at the dealership waiting for repairs. the contact stated that this was a severe safety issue because of the way the vehicle lost and gained power in heavy traffic. he does not believe that the vehicle is safe to drive. the contact wanted ford to buy the vehicle back. the failure mileage was approximately 20, 056. the current mileage was 24,100. updated 12/23/10*lj updated 01/04/11.Mileage was 20056 miles. Vehicle Identification Number (VIN):3FAHP0GA0AR. Ford Fusion 2010 problem was reported in REDLANDS, CA. Vehicle was purchased on May 07, 2010. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 65 mph. DEALER'S NAME: REYNOLDS BUICK . DEALER'S TELEPHONE NUMBER: 1-800-576-4259 . DEALER'S CITY: WEST COVINA . DEALER'S STATE CODE: CA. DEALER'S ZIPCODE: 91791 .

Ford Fusion 2010 Power Train Automatic Transmission Review #10354055

FORD FUSION 2010 car safety problem was reported on Aug 12, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . i purchased a ford fusion in march 2010. about 2 months after i received a recall notice stating the transmission needed some type of new valve and if it did not get it the clutch on my car could wear out. i immediately brought my car in and had the recall work done. soon after i starting feeling the transmission "slip" between gears. this issue almost caused an accident on the highway. i brought my car back to the dealer after having the transmission light turn on while driving to work and experiencing slippage between gears again. i was told they would check it out and try to duplicate the issue. they had the car for 8 days and said they could not find anything wrong. research on transmission problems with ford fusions proved this is a wide spread issue. after having my car for 2 days the transmission slipped again. i would appreciate any help i can get! [xxx] information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6). *tr.Mileage was 14500 miles. Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in JACKSON, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10354182

FORD FUSION 2010 car safety problem was reported on Feb 15, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . 2010 ford fusion se, transmission problems jerking slipping this is the second time i have had the car in the shop. first time they put a new part on who knows what is going on now. i bought a new car not a car with rebuilt items. this is ridiculous and unfair. ford did well this year off the hard earned money of americans and they should be ashamed for the unprofessional and down right nasty way they have treated this problem. and from what i have read it has been an on going problem for a few year. *tr.Ford Fusion 2010 problem was reported in LEBANON, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10354207

FORD FUSION 2010 car safety problem was reported on June 17, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl*the contact owns a 2010 ford fusion. the contact stated that while driving 3 mph the vehicle suddenly accelerated up to 30 mph. while trying to stop the vehicle the vehicle it crashed into another vehicle. the contact had to shift the vehicle into park in order to stop the vehicle. the contact was not injured during the crash. the contact did not file a police report. the contact called the manufacturer and they did not provide any assistance. the contact noticed numerous complaints regarding the sudden acceleration problem with this year make and model and refused to drive the vehicle in fear of causing a crash. the failure mileage was unknown. .Vehicle was involved in a crash. Mileage was 704 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in ALEXANDRIA, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 3 mph.

Ford Fusion 2010 Vehicle Speed Control Review #10355448

FORD FUSION 2010 car safety problem was reported on Sept 10, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact stated as his wife turned slowly into a parking space, the vehicle suddenly accelerated. jumped onto the sidewalk and hit a metal railing which in turn broke the store front window. there were no injuries. the following day while sitting at a complete stop, the contact removed his foot from the brake pedal and the vehicle abnormally accelerated again. the contact was able to stop the unintended acceleration by depressing the brakes. the contact called the manufacturer who advised him to take the vehicle to the dealer for diagnosis and possible repairs. the vehicle was not inspected or repaired. the failure mileage was approximately 1,310 and the current mileage was 1,364. updated 01/06/11. *lj updated 04/12/11.Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Mileage was 1310 miles. Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in WHEATON, MD. Original Owner. Vehicle was purchased on June 01, 2010. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. DEALER'S NAME: KOONS OF SILVER SPRING . DEALER'S CITY: SILVER SPRING . DEALER'S STATE CODE: MD. DEALER'S ZIPCODE: 20906 .

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10355639

FORD FUSION 2010 car safety problem was reported on Aug 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . 2010 ford fusion. hard shift with second gear, taken to dealership and recall work done. they reprogrammed the transmission twice. the car remained with hard shift in second gear and high pitch sound under the hood, heard in the vehicle any time over 100 rpms. they replaced the transmission. i had the car back 2 days and the car did not engage in second gear this morning for 2 sec. loud sound from under the hood. this is the third time back to the shop in less than a month for the transmission. *tr.Mileage was 14000 miles. Ford Fusion 2010 problem was reported in VALATIE, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 25 mph.

Ford Fusion 2010 Seats Front Assembly Head Restraint

Ford Fusion 2010 Seats Front Assembly Head Restraint Review #10355948

FORD FUSION 2010 car safety problem was reported on Sept 10, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SEATS:FRONT ASSEMBLY:HEAD RESTRAINT . tl*the contact owns a 2010 ford fusion. while traveling at any speed the contact noticed that the head rest was causing headaches and back pains due to the forward leaning position of the head rest. the current and failure mileages were 400. updated 12/23/10*lj updated 01/04/11.Mileage was 400 miles. Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in LITITZ, PA. Original Owner. Vehicle was purchased on Sept 02, 2010. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. DEALER'S NAME: WANNER FORD . DEALER'S TELEPHONE NUMBER: 717-733-4700 . DEALER'S CITY: EPHRATA . DEALER'S STATE CODE: PA. DEALER'S ZIPCODE: 17522 .

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10355953

FORD FUSION 2010 car safety problem was reported on Aug 07, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . purchased the ford fusion se 2010 on 8/4/10 drove it 100 miles and on 8/7/10 it was dead in my drive way. called road service and it was jumped and towed to dealership. there two days was told there was nothing wrong with the vehicle other than the battery was no good - they replaced the battery. drove it approximately 900 miles and on 9/5/10 it was dead in the driveway again. roadservice came jumped the car and i drove it into the dealership they replaced the battery and asked me to bring the car into service after the weekend. on 9/7/10 at 8am i dropped the car at the dealership as per their request. i received a call on 9/14/10 from the service department to tell me that they can't resolve the matter and that an engineer is coming out from ford corp to look at the car. not sure what to think at this point maybe i should ask for my money back or another car? also, i have noticed the drivers headrest is really not at all comfortable but that is really the least of my troubles with my new car. *tr.Mileage was 197 miles. Ford Fusion 2010 problem was reported in FREMONT, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10356179

FORD FUSION 2010 car safety problem was reported on Sept 14, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . 2010 ford fusion reference odi # 10351655 since the first registered complaint of rough and erratic shifting (odi 10351655) my transmission has completely failed. the ford service manager where we are waiting repair said he had not seen one in such a physical state, anything that could have melted was melted. ford has a problem with this tranmission as it is recommended for recreational towing. the unit had been adjusted and "fixed" twice before according to ford specifications and the information in bulliten (ford tsb 09-20-13) was followed. while traveling at a speed of approximately 62 mph the transmission malfunctioned and became totally disabled. if we weren't towing this vehicle securely behind a motorhome but rather driving at that rate and the cars transmission self-destructs what possible damage to life and property might have occurred???? this faulty transmission is not the only isolated incident! other dealers have been waiting for weeks for replacement parts to rebuild transmissions as a remedy to the problem. i've been assured that i will be receiving another transmission (possibly a remanufactured unit) that has received modifications for flat/ recreational towing. i would hope your agency investigates this situation thoroughly before anyone is seriously injured or killed as a result of a malfunctioning transmission in the ford fusion and 2009-2010 escape along with the mercury 2010 milan and 2009-2010 mariner. i was also lead to believe that ford had distributed information through their fmc dealer network concerning the remanufactured transmission units that had been modified for flat towing. if this information is not released publically anyone is at risk, whether driving the vehicle or traveling on the roadways along with vehicles that have the defective transmissions. please contact me at [xxx] regarding this matter. information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6). *tr .Mileage was 14600 miles. Vehicle Identification Number (VIN):3FAHP0JA5AR. Ford Fusion 2010 problem was reported in LAKE WALES, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 62 mph.

Ford Fusion 2010 Engine And Engine Cooling Engine

Ford Fusion 2010 Engine And Engine Cooling Engine Review #10357818

FORD FUSION 2010 car safety problem was reported on Sept 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE . 2010 ford fusion sel 4 cyl at . vehicle "downshifts" unexpectedly while driving highway speeds. *tr.Mileage was 15250 miles. Vehicle Identification Number (VIN):3FAHP0JA7AR. Ford Fusion 2010 problem was reported in BOWIE, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10358157

FORD FUSION 2010 car safety problem was reported on Sept 28, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . my 2010 ford fusion sel is in the shop for the 4th time due to transmission issues. the first time was based on my observation that something was wrong with the reverse gear. the dealer could find nothing. then several weeks later we received a service bulletin that something needed to be reprogrammed to fix a reverse issue--surprise! 2nd visit to service. since then, the transmission has had hard shifts from 2nd to 3rd (around 25 mph) and sometimes it feels like the gears are slipping. was in shop for the 3rd time for 5 days but "they could not re-create the problem", car returned and the same problem has continued. today, the car stopped accelerating while on the road, started to idle roughly and "shudder" and then the wrench light came on. dealer claims it is a defective throttle body. *tr.Mileage was 9500 miles. Vehicle Identification Number (VIN):3FAHP0JG5AR. Ford Fusion 2010 problem was reported in SAINT LOUIS, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10360157

FORD FUSION 2010 car safety problem was reported on May 10, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . tl*the contact owns a 2010 ford fusion. while traveling 35 mph, the contact heard a banging noise from outside the vehicle; suddenly the front drivers side tire locked up, causing a loss of control of the vehicle. the vehicle was taken to an authorized dealer where the contact was told that the cause of the failure could not be determined. the failure mileage was approximately 10,000 and the current mileage was approximately 17,000. updated 01/04/11*lj updated 01/07/11.Mileage was 10000 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in SUMMERVILLE, SC. Vehicle was purchased on Oct 10, 2009. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 35 mph. DEALER'S NAME: SUMMERVILLE FORD . DEALER'S TELEPHONE NUMBER: 843-873-3550 .

Ford Fusion 2010 Suspension

Ford Fusion 2010 Suspension Review #10360157

FORD FUSION 2010 car safety problem was reported on May 10, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION . tl*the contact owns a 2010 ford fusion. while traveling 35 mph, the contact heard a banging noise from outside the vehicle; suddenly the front drivers side tire locked up, causing a loss of control of the vehicle. the vehicle was taken to an authorized dealer where the contact was told that the cause of the failure could not be determined. the failure mileage was approximately 10,000 and the current mileage was approximately 17,000. updated 01/04/11*lj updated 01/07/11.Mileage was 10000 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in SUMMERVILLE, SC. Vehicle was purchased on Oct 10, 2009. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 35 mph. DEALER'S NAME: SUMMERVILLE FORD . DEALER'S TELEPHONE NUMBER: 843-873-3550 .

Ford Fusion 2010 Engine And Engine Cooling Engine

Ford Fusion 2010 Engine And Engine Cooling Engine Review #10362557

FORD FUSION 2010 car safety problem was reported on Oct 26, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE . we have a 2010 ford fusion s. we bought it in may and it have a starting up problem. when you try to start it (after holding the key in the on position for like 3 seconds...as it should be) , it doesn't start and then after letting the key "go", the car keeps trying to start himself up. this makes a weird noise offcourse....and then you have to quickly turn down the key to the off position for it to stop trying . this morning was the fifth time already this happened. the last time i had to try 3 times before finally getting the car to start up. this car will be going to the service/repair dep. soon at the dealer. i can't believe these problems occurs already , and the car is only 5 months old ! *tr.Mileage was 8500 miles. Ford Fusion 2010 problem was reported in ARUBA, 00. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10362690

FORD FUSION 2010 car safety problem was reported on June 30, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . stopped at a traffic light, waiting to make left turn. upon accelerating car lurched forward like it was going to come off it's chasis and then lost all acceleration. car rolled to stop and needed towing dealership had car for 25 days. claims to have replaced a throttle module which corrected the issue. ford claimed all defective parts and indicated they had no responsibility to inform me of the defect which caused the incident. *tr .Mileage was 4500 miles. Vehicle Identification Number (VIN):3FAHP0JA6AR. Ford Fusion 2010 problem was reported in OXFORD, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 5 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10362690

FORD FUSION 2010 car safety problem was reported on June 30, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . stopped at a traffic light, waiting to make left turn. upon accelerating car lurched forward like it was going to come off it's chasis and then lost all acceleration. car rolled to stop and needed towing dealership had car for 25 days. claims to have replaced a throttle module which corrected the issue. ford claimed all defective parts and indicated they had no responsibility to inform me of the defect which caused the incident. *tr .Mileage was 4500 miles. Vehicle Identification Number (VIN):3FAHP0JA6AR. Ford Fusion 2010 problem was reported in OXFORD, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 5 mph.

Ford Fusion 2010 Vehicle Speed Control Review #10362884

FORD FUSION 2010 car safety problem was reported on July 18, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl*the contact owns a 2010 ford fusion. the contact stated that when she moved toward a stop sign and attempted to stop, the vehicle suddenly accelerated forward. she attempted to brake but the vehicle would not slow down. she also noticed that the rpms were increasing rapidly and the vehicle vibrated. at the next stop, the failure occurred again. after that stop sign, the vehicle seemed to function correctly. the failure occurred another time so the contact turned the vehicle off and restarted it. the vehicle had not been inspected or repaired. the contact called the manufacturer who stated that someone would get back with her. the current mileage was approximately 1,800. the failure mileage was 75. updated 3/21/11 *cn the consumer stated as she approached a stop sign, the engine started making a loud noise and vibrating. the consumer put the vehicle in neutral and put both of her feet on the brake, but the vehicle kept pulling around the corner as she was trying to make a right. she tried to turn the vehicle off, but the vehicle accelerated out of control, hit a fence, spun around and headed toward a tree, dragging fence and poles. the vehicle finally cut off. updated 08/05/11 updated 11/22/11 *cn.Vehicle was involved in a crash. 1 person(s) were injured. Mileage was 75 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in CHARLOTTE, NC. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. DEALER'S NAME: MOORESVILLE FORD . DEALER'S TELEPHONE NUMBER: 704-664-1300 . DEALER'S CITY: MOORESVILLE . DEALER'S STATE CODE: NC. DEALER'S ZIPCODE: 28115 .

Ford Fusion 2010 Vehicle Speed Control Review #10363007

FORD FUSION 2010 car safety problem was reported on Oct 29, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . no crashes or injuries yet! i drive a 2006 ford fusion>>> well driving down the highway while on cruise control the cruise control totally stops and it the speed when from 70 down to i don't know what right away.. the reason i don't know is because the odometer error came up causing the speedometer to stop working. and to add to the confusion... the starter stopped working... all this happened on the day my dad died leaving me without a car to see my family which live 200 miles away... *tr.Mileage was 66273 miles. Ford Fusion 2010 problem was reported in MARYVILLE, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train Driveline

Ford Fusion 2010 Power Train Driveline Review #10363007

FORD FUSION 2010 car safety problem was reported on Oct 29, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:DRIVELINE . no crashes or injuries yet! i drive a 2006 ford fusion>>> well driving down the highway while on cruise control the cruise control totally stops and it the speed when from 70 down to i don't know what right away.. the reason i don't know is because the odometer error came up causing the speedometer to stop working. and to add to the confusion... the starter stopped working... all this happened on the day my dad died leaving me without a car to see my family which live 200 miles away... *tr.Mileage was 66273 miles. Ford Fusion 2010 problem was reported in MARYVILLE, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10363036

FORD FUSION 2010 car safety problem was reported on Oct 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . within two weeks of the april, 2010 purchase date, we noticed transmission problems in our 2010 ford fusion (6f35 transmission) on a cold start, namely rough shifting, transmission slipping, engine revving excessively but the car not accelerating, and the vehicle lurching forward before slamming into gear. normally, after the engine warms, the transmission smoothes out and we do not experience further problems that day. however, one episode, which recently occurred after we had driven the car continuously for 180 miles, leads us to believe that we simply cannot trust the vehicle to transport us safely. when we took off in heavy traffic after stopping for a red light, the transmission seemed to shift into neutral. after several seconds, the car slammed into gear. we were lucky to avoid being hit from the rear. the vehicle has been in for multiple transmission repair attempts--including pcm reprogramming, replacement of valve body, and rebuilding the transmission. on the last repair attempt, ford brought in a field service engineer who again "captured" the problem. yet the flaring continues. we can replicate it every day by driving the vehicle cold and accelerating normally from 0 to 55 mph on the first shifting sequence. we are convinced that a major design flaw exists in the transmission of the 2010 ford fusion. ford needs to address this serious safety issue immediately! *tr.Vehicle Identification Number (VIN):3FAHP0JA8AR. Ford Fusion 2010 problem was reported in GREENVILLE, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Steering

Ford Fusion 2010 Steering Review #10363555

FORD FUSION 2010 car safety problem was reported on Oct 30, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with STEERING . i have a brand new 2010 ford fusion that has approximately 3000 miles on it. i had a bad experience where the power steering suddenly stopped working while pulling my car out of a parking garage. the vehicle console display showed a 'power steering assist failure' message. i pulled my car over to the side with considerable effort and shut the ignition off. after a few minutes wait, i restarted the car and everything was normal. within a few minutes, a less than a mile traveled, the same failure occurred and the same message was displayed while in a round-about. i again pulled my car over and shut it off. it again restarted and steered fine and i drove immediately to my dealership. the dealership read the code, cleared it and informed me that they could not get the vehicle to reproduce the problem. this is a very scary issue and no components were replaced. i am a prior owner of a chevrolet cobalt and i am familiar with their recall for the electric assist. my cobalt did not fail, but they replaced the assist motor under recall. i did not realize that the ford fusion now has electric assist. are other fusion owners having intermittent failures with their steering? *tr.Mileage was 3500 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in FARMLAND, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 1 mph.

Ford Fusion 2010 Wheels Lugs/nuts/bolts

Ford Fusion 2010 Wheels Lugs/nuts/bolts Review #10364337

FORD FUSION 2010 car safety problem was reported on Nov 07, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS:LUGS/NUTS/BOLTS . i went to move my 2010 ford fusion in my driveway and noticed that one of my driver side rear tire lug nuts was missing. looking closer the whole stud had sheared off. the car only has 9788 miles and an identical problem on another 2010 ford fusion with 10500 miles had three studs sheared on the rear passenger side wheel. *tr.Mileage was 9788 miles. Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in MASON, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10366657

FORD FUSION 2010 car safety problem was reported on Feb 21, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . tl*the contact owns a 2010 ford fusion. while the contact was driving approximately 45 mph, the transmission began to exhibit erratic and violent shifting. the vehicle was taken to an authorized dealer where the transmission was replaced for the third time. the failure mileage was 9,700. .Mileage was 9700 miles. Vehicle Identification Number (VIN):3FAHP0JA5AR. Ford Fusion 2010 problem was reported in LAKE WALES, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Seats

Ford Fusion 2010 Seats Review #10366890

FORD FUSION 2010 car safety problem was reported on Nov 15, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SEATS . 2011 ford fusion headrest is so far forward that it forces my wife's head forward, causing severe neck pain. as a result she removed the headrest. this is unsafe situation but necessary for her to be able to drive the card. *tr.Ford Fusion 2010 problem was reported in LAPEER, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10369166

FORD FUSION 2010 car safety problem was reported on Oct 10, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . purchased a new 2010 ford fusion se, 4 cyl with 6 speed auto trans. transmission started slipping within 2 months of purchase. the car has been taken back to dealer 3 times. 10/12/10 at dealer-they stated they could not duplicate the problem. 2nd time 10/25/10 dropped car off at dealer. same problem, transmission slipping between 2nd and 3rd gear-safety issue with pulling out on busy streets. dealer performed "reinstall valve body codes and clear tcm. learn road test performed." they stated they could not duplicate the problem. end of november wife and kids in car and slipped between 2nd and 3rd gear on while on busy road-huge safety concern due to almost rear-ended. took car back to dealer on 11/29/10 with the same problem. dealer kept for several days but "could not duplicate the problem." i have contacted ford motor company several times and spoke with customer service. they have documented these complaints also. this is a major safety issue as this problem can happen at any time. i does not happen everyday, but the last time was on a busy road and could have been involved in an accident due to mechanical failure. *tr.Mileage was 2500 miles. Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in TEMPERANCE, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10369450

FORD FUSION 2010 car safety problem was reported on Dec 05, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . i have a 2010 for fusion that was part of the transmission recall ,which has been taken care of. i have been experiencing slow delays of acceleration after pressing the gas pedal. twice i have experienced where my car won't shift out of gear. the last time i was on the highway and the rpm was stuck at 4 with a speed of 60. the car finally switched gears, but the car then raced forward. luckily no one was in front of me. i feel that this is a major safety risk for the owners of these cars. i have an appt scheduled on 12/13 with the dealer. *tr.Mileage was 12500 miles. Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in PARMA HTS, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10369468

FORD FUSION 2010 car safety problem was reported on Jan 05, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . tl* the contact owns a 2010 ford fusion. the contact was driving approximately 55 mph when she noticed that the vehicle was jumping gears abnormally. the vehicle was also exhibiting an unusual increase in engine rpms and loud roaring noise. the contact stated that the failure would occur whether sitting idle, in park or in drive. the vehicle was inspected by the dealer who informed the contact that they were unable to diagnose the problem. the vehicle was not repaired. the failure mileage was approximately 14,000. .Mileage was 14000 miles. Vehicle Identification Number (VIN):3FAHP0GA4AR. Ford Fusion 2010 problem was reported in MISSION HILLS, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10370431

FORD FUSION 2010 car safety problem was reported on Oct 24, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . on oct 24, 2010 while driving approximately 75-80 mph (left lane) of a major freeway, tachometer revved to 4,000 rpm and stuck there. vehicle rpm's would not go up or down and transmission appeared to be slipping in 6th gear. this incident occurred at 27,522 miles. managed to get car to side of road, where rpm's returned to normal for idling condition. at this point, the little "wrench" light appeared on the dash. the car was shut off and restarted in an attempt to reset the code. all appeared well, and i proceeded to re-enter the freeway. at approximately 27,533 miles (11 miles later), the vehicle experienced the same thing. please note that on june 14, 2010 the vehicle was taken to dealership and the "customer satisfaction program (program number 10b15) was performed on vehicle (mileage: 19,936 miles). as it appears that something is major wrong with this transmission, the vehicle was once again taken to the dealership (oct. 29, 2010: mileage: 27,760 miles) to have this issue re-evaluated. at this time, the dealership performed tsb 10-21-9. there was a noticeable difference in the shift quality of the vehicle. this same problem occurred again on dec. 1, 2010 (mileage: 30,138 miles) while driving 70 mph; the transmission appeared to slip and rpm's revved up to 4,000 rpm. the vehicle has not been taken back to the dealership at this time as problem is not reproducible and is unpredictable. this is a potential safety hazard as transmission could fail at any time while traveling on the freeway. *tr.Mileage was 27522 miles. Vehicle Identification Number (VIN):3FAHP0HA4AR. Ford Fusion 2010 problem was reported in NOVI, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 75 mph.

Ford Fusion 2010 Air Bags

Ford Fusion 2010 Air Bags Review #10370449

FORD FUSION 2010 car safety problem was reported on Nov 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with AIR BAGS . tl*the contact owns a 2010 ford fusion. the contact stated that the air bag warning light illuminated intermittently. the dealer made two attempts to diagnose the failure. the air bag sensor was replaced; however, the warning light continued to illuminate. the vehicle was being repaired by an authorized dealer. the current mileage was approximately 6,000. the failure mileage was approximately 4,000. the vin was unavailable. .Mileage was 4000 miles. Ford Fusion 2010 problem was reported in CONCORD, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Seats

Ford Fusion 2010 Seats Review #10370606

FORD FUSION 2010 car safety problem was reported on Mar 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SEATS . i have a 2010 ford fusion sel and the headrest is too far forward as not to be comfortable. i have back and neck problems as it is and this only makes it worse! i have to put the seat back back so far to not have my head crunched forward. *tr.Mileage was 0 miles. Vehicle Identification Number (VIN):3FAHP0JA2AR. Ford Fusion 2010 problem was reported in SAHUARITA, AZ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Visibility

Ford Fusion 2010 Visibility Review #10370611

FORD FUSION 2010 car safety problem was reported on May 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY . i have a 2010 ford fusion sel and right after i first got it i had a crack in windshield and thought a rock must have hit it. i got it repaired (after many problems with the repairs) and not long after i got a star burst. will have to have it fixed now too! i have had many cars throughout the years and have never had to replace the windshield, this one now twice and only 10,000 miles on it???? *tr.Mileage was 4000 miles. Vehicle Identification Number (VIN):3FAHP0JA2AR. Ford Fusion 2010 problem was reported in SAHUARITA, AZ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10370999

FORD FUSION 2010 car safety problem was reported on Dec 16, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . transmission slips between 2nd and 3rd gear every day when the engine is cold. three times has caused violent shaking of the vehicle. i was close to being t boned due to the slippage once as the car wouldn't continue on the proper acceleration path. *tr.Mileage was 13400 miles. Vehicle Identification Number (VIN):3FAHP0JG5AR. Ford Fusion 2010 problem was reported in ELKHART, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10371175

FORD FUSION 2010 car safety problem was reported on Dec 18, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . i have a 2010 ford fusion with 13k miles on it, that has been providing me with tremendous amount of heartache. the vehicle will automatically slip into random gears while driving, even to the extent of shifting from 6 gear all the way down to 1st. i was driving down i-17 in arizona doing the speed limit of 75mph when for the second time it slipped all the way in to 1st gear. both times this occurred it nearly caused an accident because my speed decreased so suddenly i was almost rear end at 75mph. i am actually fearful for my wife, who primarily drives it, and my son safely. i have brought the vehicle in before and they cant find anything wrong with it, but yet there are numerous customers with the same complaint. a simple online search will reveal that. ford is aware of this problem, but individual dealers are only treating the symptoms and not actually fixing the problem. this has to be corrected before someone dies. *tr.Mileage was 13900 miles. Vehicle Identification Number (VIN):3FAHP0JA4AR. Ford Fusion 2010 problem was reported in PEORIA, AZ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10371175

FORD FUSION 2010 car safety problem was reported on Dec 18, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . i have a 2010 ford fusion with 13k miles on it, that has been providing me with tremendous amount of heartache. the vehicle will automatically slip into random gears while driving, even to the extent of shifting from 6 gear all the way down to 1st. i was driving down i-17 in arizona doing the speed limit of 75mph when for the second time it slipped all the way in to 1st gear. both times this occurred it nearly caused an accident because my speed decreased so suddenly i was almost rear end at 75mph. i am actually fearful for my wife, who primarily drives it, and my son safely. i have brought the vehicle in before and they cant find anything wrong with it, but yet there are numerous customers with the same complaint. a simple online search will reveal that. ford is aware of this problem, but individual dealers are only treating the symptoms and not actually fixing the problem. this has to be corrected before someone dies. *tr.Mileage was 13900 miles. Vehicle Identification Number (VIN):3FAHP0JA4AR. Ford Fusion 2010 problem was reported in PEORIA, AZ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Steering

Ford Fusion 2010 Steering Review #10373154

FORD FUSION 2010 car safety problem was reported on Dec 19, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with STEERING . tl* the contact owns a 2010 ford fusion. the contact was driving in reverse 2 mph when the power steering assist fault light illuminated. the vehicle was taken to the dealer where they advised the contact that the power steering assist module was defective. the vehicle was left with the dealer where the contact was awaiting repairs. the failure and current mileage was 52,039..Mileage was 52039 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in COLUMBIANNA, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 2 mph.

Ford Fusion 2010 Wheels Lugs/nuts/bolts

Ford Fusion 2010 Wheels Lugs/nuts/bolts Review #10373257

FORD FUSION 2010 car safety problem was reported on Dec 17, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS:LUGS/NUTS/BOLTS . involves 3 identical 2010 ford fusions that were purchased new for our company fleet, purchased total of 22 cars in this delivery. on 3 separate occasions involving 3 separate cars our fleet drivers experienced vibration and shimmy/shake while operating cars. it was determined in both cases that the vehicles lug nut on one vehicle and 3 on another had failed. these vehicles were never serviced other than a oil change and were less than 3 months in service when the incidents occurred. they occurred approximately one month apart and involved 3 different drivers. the cars were fixed under warranty by local ford dealers who could not explain the reasoning other than to say someone may have tried to steal them or overtorqued the lug nuts. vehicles were not garaged at same addresses and again were never serviced as they were new and the tires were steel wheel with hubcaps. the likeliness that 3 different cars on 3 different occasions had attempted wheel thefts is fairly low. we questioned why a thief would overtighten lug nuts, and both dealers replaced parts under warranty. parts replaced involved wheel lug nuts and studs. parts were retained by dealers. *tr.Mileage was 5000 miles. Vehicle Identification Number (VIN):3FAHP0HA2AR. Ford Fusion 2010 problem was reported in MT LAUREL, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10374127

FORD FUSION 2010 car safety problem was reported on June 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . tl* the contact owns a 2010 ford fusion. while driving approximately 70 mph, the contact stated that the transmission disengaged from the engine, causing loss of all power without warning. the vehicle was taken to the dealer who reprogrammed the computer in june 2010; however, the problem occurred again in january 2011. the contact did not inform the manufacturer nor was the vehicle repaired. the current mileage was approximately 34,000. the failure mileage was approximately 23,000. the vin was unavailable. .Mileage was 23000 miles. Ford Fusion 2010 problem was reported in HELLRUNG, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10374867

FORD FUSION 2010 car safety problem was reported on Jan 05, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . i am experiencing chronic shifting problems with the 6f35 transmission. this transmission suffers from slipping gears, shift flares, harsh shifting, and funny shifting that will be followed by an uncontrollable forward lurch. the dealership determined that my valve body failed at 3,744 miles and proceeded to replace the valve body and solenoid assembly. then at 4,526 miles i had the recall 10b15 powertrain control module reprogramming performed on my car. next, at 4,727 miles the dealer informed me that my car passed the transmission load test. at 9,181 miles the dealership verified my shift flaring problem. they reflashed my pcm with an updated software program. trans tech drove vehicle and the trans continued to flare. the dealer then removed my transmission and mounted to the bench for overhaul. the dealer discovered that my valve body had 3 melted bolts, my valve body was damaged, and that my clutches had burned out. the dealer proceeded to install a new valve body, forward clutch, overdrive clutch, piston, seals, and gaskets. at 9,702 miles my car returned to the dealership for shifting problems and poor overall transmission operation. i was told by the dealership that everything was normal at this time. i believe that i was told this because there are no more repairs available at this time. i am sick and tired of ford giving everyone the run around on these transmissions. they need to man up and let people know what is really going on. my transmission continues to experience shift flaring, violent downshift slams, erratic shifting, delayed shifting, forward lurches, and struggles on takeoff. with every repair attempt the overall performance of this transmission worsens every time. it shifts as though it was designed by a bunch of amateur's. i no longer feel safe driving my car due to the uncontrollable forward lurches and extended delayed shift where the car won't move for a few seconds. please fix this before someone gets killed or injured! *tr.Mileage was 9800 miles. Vehicle Identification Number (VIN):3FAHP0JG1AR. Ford Fusion 2010 problem was reported in BEVERLY HILLS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10374923

FORD FUSION 2010 car safety problem was reported on Feb 05, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . purchased a new 2010 ford fusion se i-4 in october, 2009. i drove the vehicle for 4 months and noticed a water-sloshing/waterfall sound (similar to a dishwasher) coming from the dashboard area upon start-up and low acceleration in cold weather. took the vehicle to the same ford dealership it was purchased from to perform service. after 5 visits and nearly 1 year later, the issue is still remaining. ford has issued 2 technical service bulletins on the issue, none of which have been able to solve the issue. ford claims to not know what is causing the sound, but maintains that it is not a safety or drive-ability issue. ford claims the issue is air bubbles trapped in the heater core, but during a service visit, no air was removed from the heater core system and the problem persisted. this is unacceptable for a brand new vehicle. *tr.Mileage was 5000 miles. Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in ADA, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. VEHICLE SPEED: 5 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10375247

FORD FUSION 2010 car safety problem was reported on Jan 08, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . ford fusion 2010 - automatic transmission failure - can not trust this car to work properly - hard shifting - lurching forward - transmission tripping over itself like a 13 year old car at 1 month - 2 months acceleration problems - 3 months lurching forward and not moving when put into reverse - 6 months out of the blue violent shaking of the vehicle as if a wheel was about to fall off. at 6 months old that car is behaving mechanically worse than a 13 year old car - this car is unsafe - seriously thinking about dumping it back at the dealership as it is a lease. 31,000 km is when the violent shaking at higher speeds began (out of the blue). *ln.Mileage was 31000 miles. Ford Fusion 2010 problem was reported in BRAMPTON, 00. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Engine And Engine Cooling Engine

Ford Fusion 2010 Engine And Engine Cooling Engine Review #10376339

FORD FUSION 2010 car safety problem was reported on Dec 15, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE . the area of the heater / dashboard makes a gurgle or sloshing noise at startup and upon acceleration. there is clearly air in the heating/cooling system that could be damaging internal parts. ford does not currently have a repair for this issue. *tr.Mileage was 10000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in ROOTSTOWN, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Engine And Engine Cooling Review #10376339

FORD FUSION 2010 car safety problem was reported on Dec 15, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . the area of the heater / dashboard makes a gurgle or sloshing noise at startup and upon acceleration. there is clearly air in the heating/cooling system that could be damaging internal parts. ford does not currently have a repair for this issue. *tr.Mileage was 10000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in ROOTSTOWN, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Visibility Sun Roof Assembly

Ford Fusion 2010 Visibility Sun Roof Assembly Review #10377402

FORD FUSION 2010 car safety problem was reported on Dec 06, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:SUN ROOF ASSEMBLY . 2010 ford fusion. consumer writes regarding a large hole measuring approximately 15 inches wide and 10 inches deep due to the sunroof cover inside the vehicle opened up while driving *tgw the consumer stated sunroof glass and fragments were everywhere in the sunroof well. *jb .Ford Fusion 2010 problem was reported in CUMMING, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Wheels Lugs/nuts/bolts

Ford Fusion 2010 Wheels Lugs/nuts/bolts Review #10378953

FORD FUSION 2010 car safety problem was reported on Dec 17, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS:LUGS/NUTS/BOLTS . involves 3 identical 2010 ford fusions that were purchased new for our company fleet, purchased total of 22 cars in this delivery. on 3 separate occasions involving 3 separate cars our fleet drivers experienced vibration and shimmy/shake while operating cars. it was determined in both cases that the vehicles lug nut on one vehicle and 3 on another had failed. these vehicles were never serviced other than a oil change and were less than 3 months in service when the incidents occured. they occured approxiimately one month apart and involved 3 different drivers. the cars were fixed under warranty by local ford dealers who could not explain the reasoning other than to say someone may have tried to steal them or overtorqued the lug nuts. vehicles were not garaged at same addresses and again were never serviced as they were new and the tires were steel wheel with hubcaps. the likeliness that 3 different cars on 3 different occasions had attempted wheel thefts is fairly low. we questioned why a thief would overtighten lug nuts, and both dealers replaced parts under warranty. parts replaced involved wheel lug nuts and studs. parts were retained by dealers..Mileage was 10654 miles. Vehicle Identification Number (VIN):3FAHP0HA4AR. Ford Fusion 2010 problem was reported in MT LAUREL, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Wheels Lugs/nuts/bolts Review #10378954

FORD FUSION 2010 car safety problem was reported on Dec 17, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS:LUGS/NUTS/BOLTS . involves 3 identical 2010 ford fusions that were purchased new for our company fleet, purchased total of 22 cars in this delivery. on 3 separate occasions involving 3 separate cars our fleet drivers experienced vibration and shimmy/shake while operating cars. it was determined in both cases that the vehicles lug nut on one vehicle and 3 on another had failed. these vehicles were never serviced other than a oil change and were less than 3 months in service when the incidents occured. they occured approxiimately one month apart and involved 3 different drivers. the cars were fixed under warranty by local ford dealers who could not explain the reasoning other than to say someone may have tried to steal them or overtorqued the lug nuts. vehicles were not garaged at same addresses and again were never serviced as they were new and the tires were steel wheel with hubcaps. the likeliness that 3 different cars on 3 different occasions had attempted wheel thefts is fairly low. we questioned why a thief would overtighten lug nuts, and both dealers replaced parts under warranty. parts replaced involved wheel lug nuts and studs. parts were retained by dealers..Mileage was 8000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in MT LAUREL, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10378957

FORD FUSION 2010 car safety problem was reported on June 21, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . i purchased my vehicle on may 15, 2010. the vehicle began to stall almost 1 month later at 2100 miles. i was coming to a stop at a red light when i noticed that my vehicle had lost all power when i began to apply the brake. i took the vehicle into the dealer and they told me that they were not able to replicate the problem and no codes were showing up when diagnosed. after the first time the vehicle stalled on me i started to notice an acceleration problem prior to the vehicle stalling again. it feels like the vehicle is not shifting gears correctly when i'm pressing the gas for acceleration. the vehicle has trouble accelerating properly and i fear that i may get rear ended. when the vehicle stalls it does not give me any warning signs and just looses power. i have to turn off the ignition and turn it back on. the vehicle starts up right away like if nothing happened. meanwhile i loose power in the middle of the freeway or on the street, fearing that i will get rear ended. the vehicle has stalled on me numerous times and each time i take it into the dealer they are not able to replicate the problem. the dealer placed a flight recorder to monitor the vehicle and they still weren't able to capture anything when the vehicle stalled, so they say. i have contact ford corporation and have notified them of the problem but they are not working to fix the problem. they keep changing me from dealer to dealer and they have not sent out a ford technician as promised to look at the vehicle. this is a huge safety concern that ford is not addressing. i have put in numerous calls to ford corporation and they have not fixed the problem to this day. .0 person(s) were injured. 0 person(s) died.Mileage was 2100 miles. Vehicle Identification Number (VIN):3FAHP0JG5AR. Ford Fusion 2010 problem was reported in CERRITOS, CA. Vehicle was not using Cruise Control. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10378957

FORD FUSION 2010 car safety problem was reported on June 21, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i purchased my vehicle on may 15, 2010. the vehicle began to stall almost 1 month later at 2100 miles. i was coming to a stop at a red light when i noticed that my vehicle had lost all power when i began to apply the brake. i took the vehicle into the dealer and they told me that they were not able to replicate the problem and no codes were showing up when diagnosed. after the first time the vehicle stalled on me i started to notice an acceleration problem prior to the vehicle stalling again. it feels like the vehicle is not shifting gears correctly when i'm pressing the gas for acceleration. the vehicle has trouble accelerating properly and i fear that i may get rear ended. when the vehicle stalls it does not give me any warning signs and just looses power. i have to turn off the ignition and turn it back on. the vehicle starts up right away like if nothing happened. meanwhile i loose power in the middle of the freeway or on the street, fearing that i will get rear ended. the vehicle has stalled on me numerous times and each time i take it into the dealer they are not able to replicate the problem. the dealer placed a flight recorder to monitor the vehicle and they still weren't able to capture anything when the vehicle stalled, so they say. i have contact ford corporation and have notified them of the problem but they are not working to fix the problem. they keep changing me from dealer to dealer and they have not sent out a ford technician as promised to look at the vehicle. this is a huge safety concern that ford is not addressing. i have put in numerous calls to ford corporation and they have not fixed the problem to this day. .0 person(s) were injured. 0 person(s) died.Mileage was 2100 miles. Vehicle Identification Number (VIN):3FAHP0JG5AR. Ford Fusion 2010 problem was reported in CERRITOS, CA. Vehicle was not using Cruise Control. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10381337

FORD FUSION 2010 car safety problem was reported on Jan 30, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . 2010 fusion se l2.5l fwd-transmission leaks oil at the driver side half shaft seal. its zero out and & the grove box manual has no sub freezing procedure to check the atf. after 2 days of ownership i contacted ford service and they were unaware of any tsb's for this problem. after some googling i found 6 or so tsb's on this 6f35 transmission and many customer complaints chronicled in forums. even fords own fusion forum has more negative than positive about this transmission. fordfusionforum.com. *tr.Ford Fusion 2010 problem was reported in BLOOMINGTON, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Ford Fusion 2010 drive type:FWD.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10381431

FORD FUSION 2010 car safety problem was reported on Oct 10, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . broken wheel studs 2010 fusion 2 broke oct 2010 left rear whell replace 2-8-11 noticed 1 missing passenger front 1 missing driver rear. delaer will not replace all as i requested for safety. updated 02/11/11 *bf updated ivoq 03/16/11 *tr.Mileage was 6597 miles. Vehicle Identification Number (VIN):3FAHP0HG0AR. Ford Fusion 2010 problem was reported in ROCKWOOD, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: BIFUEL. VEHICLE SPEED: 0 mph. DEALER'S NAME: GORNO FORD . DEALER'S TELEPHONE NUMBER: 734-676-2200 . DEALER'S CITY: WOODHAVEN . DEALER'S STATE CODE: MI. DEALER'S ZIPCODE: 48183 .

Ford Fusion 2010 Wheels Lugs/nuts/bolts

Ford Fusion 2010 Wheels Lugs/nuts/bolts Review #10381431

FORD FUSION 2010 car safety problem was reported on Oct 10, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS:LUGS/NUTS/BOLTS . broken wheel studs 2010 fusion 2 broke oct 2010 left rear whell replace 2-8-11 noticed 1 missing passenger front 1 missing driver rear. delaer will not replace all as i requested for safety. updated 02/11/11 *bf updated ivoq 03/16/11 *tr.Mileage was 6597 miles. Vehicle Identification Number (VIN):3FAHP0HG0AR. Ford Fusion 2010 problem was reported in ROCKWOOD, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: BIFUEL. VEHICLE SPEED: 0 mph. DEALER'S NAME: GORNO FORD . DEALER'S TELEPHONE NUMBER: 734-676-2200 . DEALER'S CITY: WOODHAVEN . DEALER'S STATE CODE: MI. DEALER'S ZIPCODE: 48183 .

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10383010

FORD FUSION 2010 car safety problem was reported on Jan 14, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . transmission shifting problems in 2010 ford fusion, 4 cyl, 6 speed automatic transmission. transmission replaced at 12,000 miles by ford under warranty. vehicle now has 36,000 miles and shifts erratically on a random basis. typically vehicle must be driven at least 8 miles before problems occurs. common problem involves 1-2 shift and 2-3 shift. transmission will shift hard or will shift into neutral. ford diagnostic computers indicate transmission is operating properly. internet search reveals that this is a common problem. dangerous condition presented when vehicle driven in traffic, up hills, and when entering interstate system. *tr.Mileage was 12000 miles. Ford Fusion 2010 problem was reported in SANTA CLARITA, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10383179

FORD FUSION 2010 car safety problem was reported on Jan 07, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . 2010 ford fusion 6000 miles experiencing transmission shifting issues since 3000 miles. dealer says they don't notice anything and no tsb's but there are tons of web posts about defective transmissions and recalls noting the same issues, hard shifting , delays, etc. *tr.Mileage was 3500 miles. Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in RIVERSIDE, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10383227

FORD FUSION 2010 car safety problem was reported on Jan 24, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . tl*the contact owns a 2010 ford fusion hybrid. while the vehicle was parked the ignition would not start. the vehicle was towed to the dealer. the technicians replaced the battery. the contact stated that the failure occurred a second time and the vehicle was towed to the dealer. the technicians were able to duplicate the failure but could not diagnose the failure. the vehicle was not repaired. the approximate failure mileage was 10,700. updated 04/15/11*lj updated 5/2/11 *cn updated 05/13/11 updated 12/28/2011 *ln.Mileage was 10700 miles. Vehicle Identification Number (VIN):3FADP0L3XAR. Ford Fusion 2010 problem was reported in MARIETTA, GA. Original Owner. Vehicle was purchased on Apr 23, 2009. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: HYBRID ELECTRIC. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph. DEALER'S NAME: HARDY FAMILY FORD . DEALER'S TELEPHONE NUMBER: 770-443-8891 . DEALER'S CITY: DALLAS . DEALER'S STATE CODE: GA. DEALER'S ZIPCODE: 30157 .

Ford Fusion 2010 Engine And Engine Cooling Cooling System

Ford Fusion 2010 Engine And Engine Cooling Cooling System Review #10383311

FORD FUSION 2010 car safety problem was reported on Dec 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:COOLING SYSTEM . i have a 2010 ford fusion i bought it brand new in july 2010, already i have had to replace the radiator it was not covered under the manufac warranty. there is slots in the grill of the car pretty big they told me a rock must of went thru there when i was driving and made the hole in the radiator my insurance had to pay and i paid my 300 deductible . for a couple weeks prior to that i heard a gurgling sound under the dash board. good thing i went to the dealer the day i did because the heat was blowing cold air. my radiator was bone dry and the noise under the dash was real loud at this point . well anyway i went to pick the car up and they said it was fixed but i heard the gurgling sound still under the dash {near the glove comp} i don't know what they did{the guy tried to tell me it was normal at first until he heard the noise himself} well anyway he brought it back into the service dept quirk chevrolet in quincy mass and they fixed the problem. but what i am getting at is i think there is a huge defect in the slats in the grill that it would allow anything in to hurt the radiator i have owned many cars in my life and this has never happened to me before. also the door handle is falling off already on the drivers] inside] door. *tr.Mileage was 6000 miles. Vehicle Identification Number (VIN):1G1LD55M1RY. Ford Fusion 2010 problem was reported in DORCHESTER, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10383970

FORD FUSION 2010 car safety problem was reported on July 11, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . i have a transmission problem where it slip into neutral for a few seconds between 1-2 and 2-3 causing an acceleration delay while in traffic. the engine just revs and then a shuttered lurch when the transmission slams into the next gear. i have had the car in for repair, was told the transmission was fine and all it needed was a reprogram. now i still have the issue, im taking the car back in and im dismayed to hear that even if they now rebuild the trans, ill still have to deal with the problem as ford doesnt know how to fix it. and i have been told by the dealership you can bring it in and well check it out but i dont think we can fix it. nhtsa has to step in, ford owners are in jeopardy. *tr.Mileage was 10000 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in STERLING HEIGHTS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Power Train Review #10384933

FORD FUSION 2010 car safety problem was reported on Oct 12, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . this vehicle has been serviced nine times at dealer with symptoms of transmission slipping between 2nd and 3rd gear. it continues to do the same with harsh transmission engagements, slipping causing rpm's greater than 5000. a vehicle event recorder was installed into the vehicle and problem identified. valve body has been cleaned, new transmission solenoid, "re-flashed" 2 times with no changes. ford customer service involved from beginning. at one point received call from customer service district manager stating it is "normal" for the car to shift this way and there is no problem even after the problem has been identified. this continues to be a huge safety issue as the car slips at any time in any traffic. there has not been a solution to fix this problem nor any guarantee. something has to be done to fix the problem that affects many owners with this 6 speed automatic transmission. previous complaint odi 10369166. .Mileage was 2400 miles. Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in TEMPERANCE, MI. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Power Train Review #10384933

FORD FUSION 2010 car safety problem was reported on Oct 12, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . this vehicle has been serviced nine times at dealer with symptoms of transmission slipping between 2nd and 3rd gear. it continues to do the same with harsh transmission engagements, slipping causing rpm's greater than 5000. a vehicle event recorder was installed into the vehicle and problem identified. valve body has been cleaned, new transmission solenoid, "re-flashed" 2 times with no changes. ford customer service involved from beginning. at one point received call from customer service district manager stating it is "normal" for the car to shift this way and there is no problem even after the problem has been identified. this continues to be a huge safety issue as the car slips at any time in any traffic. there has not been a solution to fix this problem nor any guarantee. something has to be done to fix the problem that affects many owners with this 6 speed automatic transmission. previous complaint odi 10369166. .Mileage was 2400 miles. Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in TEMPERANCE, MI. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10383986

FORD FUSION 2010 car safety problem was reported on May 10, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . tl* the contact owns a 2010 ford fusion. the contact stated that the reprogramming of the computer for shift modification was affecting the overall fuel mileage and performance of the vehicle. the contact informed the dealer who was not willing to address the issue and ignored the failure. the vehicle had not been repaired. the current mileage was 32,000 and the failure mileage was 14,000. updated 04/15/11*lj the transmission was replaced. updated 11/18/11 .Mileage was 14000 miles. Vehicle Identification Number (VIN):3FAHP0GA0AR. Ford Fusion 2010 problem was reported in REDLANDS, CA. Vehicle was purchased on May 07, 2010. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10384842

FORD FUSION 2010 car safety problem was reported on Dec 03, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . transmission had to be rebuilt around 20,000 miles. after it was rebuilt the car had no power so they reprogrammed it for the 6th time with the third different program. now drives worse than ever. routinely shifts between 5000 and 6000 rpm. gas mileage has decreased. i was told the new program is designed to make the car shift higher so the clutch doesn't burn out again. *tr.Mileage was 20000 miles. Vehicle Identification Number (VIN):3FAHP0JA4AR. Ford Fusion 2010 problem was reported in GLADSTONE, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10388630

FORD FUSION 2010 car safety problem was reported on Feb 09, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . after driving about 1.5 miles from home, my wife came to a set of lights and stepped on the brake to stop. the brake pedal went nearly to the floor and several dash lights came on including the brakes & anti-swerve. the vehicle slowed to a stop as she entered the intersection. fortunately 2 things were in her favor, there was no one ahead of her and there was no cross traffic at the light. either could have resulted in an accident. she drove the vehicle back home since she considered that the brakes had failed and she may not be able to stop the vehicle. she called me. i told her to call the dealership. she left the vehicle running thinking that perhaps as it warmed up it would work and tested it several times over an hour's time in the driveway. she pulled out the car's manual to see if there was anything listed regarding the brake failure. she read in another part of the manual about resetting the car's computer by shutting off the engine. when she restarted the vehicle, the dash lights went out and brakes returned to normal. the dealer said they "never heard of this problem" and said the earliest they could see the vehicle was 5 days later. we dropped the vehicle off the night before with a description of what was experienced. the dealer said they "could not verify the concern" and ford does not provide any guidance regarding the issue. i was able to find quite of few instances by simply doing a "google" search including a video by 'consumer reports' who experienced the exact same problem. ford assured them it was a 'software' issue and claimed that all 2010 fusion hybrid owners would be notified to have the software updated. my car was a newer model 2010 and apparently not under this notification since we did not receive anything from ford. the 'ford customer care' suggested taking the vehicle to another dealer for service who said, "there is nothing we can do.".Mileage was 14000 miles. Vehicle Identification Number (VIN):3FADP0L35AR. Ford Fusion 2010 problem was reported in APPLETON, WI. Vehicle was not using Cruise Control. VEHICLE SPEED: 25 mph.

Ford Fusion 2010 Unknown Or Other

Ford Fusion 2010 Unknown Or Other Review #10388630

FORD FUSION 2010 car safety problem was reported on Feb 09, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with UNKNOWN OR OTHER . after driving about 1.5 miles from home, my wife came to a set of lights and stepped on the brake to stop. the brake pedal went nearly to the floor and several dash lights came on including the brakes & anti-swerve. the vehicle slowed to a stop as she entered the intersection. fortunately 2 things were in her favor, there was no one ahead of her and there was no cross traffic at the light. either could have resulted in an accident. she drove the vehicle back home since she considered that the brakes had failed and she may not be able to stop the vehicle. she called me. i told her to call the dealership. she left the vehicle running thinking that perhaps as it warmed up it would work and tested it several times over an hour's time in the driveway. she pulled out the car's manual to see if there was anything listed regarding the brake failure. she read in another part of the manual about resetting the car's computer by shutting off the engine. when she restarted the vehicle, the dash lights went out and brakes returned to normal. the dealer said they "never heard of this problem" and said the earliest they could see the vehicle was 5 days later. we dropped the vehicle off the night before with a description of what was experienced. the dealer said they "could not verify the concern" and ford does not provide any guidance regarding the issue. i was able to find quite of few instances by simply doing a "google" search including a video by 'consumer reports' who experienced the exact same problem. ford assured them it was a 'software' issue and claimed that all 2010 fusion hybrid owners would be notified to have the software updated. my car was a newer model 2010 and apparently not under this notification since we did not receive anything from ford. the 'ford customer care' suggested taking the vehicle to another dealer for service who said, "there is nothing we can do.".Mileage was 14000 miles. Vehicle Identification Number (VIN):3FADP0L35AR. Ford Fusion 2010 problem was reported in APPLETON, WI. Vehicle was not using Cruise Control. VEHICLE SPEED: 25 mph.

Ford Fusion 2010 Service Brakes, Hydraulic

Ford Fusion 2010 Service Brakes, Hydraulic Review #10388630

FORD FUSION 2010 car safety problem was reported on Feb 09, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC . after driving about 1.5 miles from home, my wife came to a set of lights and stepped on the brake to stop. the brake pedal went nearly to the floor and several dash lights came on including the brakes & anti-swerve. the vehicle slowed to a stop as she entered the intersection. fortunately 2 things were in her favor, there was no one ahead of her and there was no cross traffic at the light. either could have resulted in an accident. she drove the vehicle back home since she considered that the brakes had failed and she may not be able to stop the vehicle. she called me. i told her to call the dealership. she left the vehicle running thinking that perhaps as it warmed up it would work and tested it several times over an hour's time in the driveway. she pulled out the car's manual to see if there was anything listed regarding the brake failure. she read in another part of the manual about resetting the car's computer by shutting off the engine. when she restarted the vehicle, the dash lights went out and brakes returned to normal. the dealer said they "never heard of this problem" and said the earliest they could see the vehicle was 5 days later. we dropped the vehicle off the night before with a description of what was experienced. the dealer said they "could not verify the concern" and ford does not provide any guidance regarding the issue. i was able to find quite of few instances by simply doing a "google" search including a video by 'consumer reports' who experienced the exact same problem. ford assured them it was a 'software' issue and claimed that all 2010 fusion hybrid owners would be notified to have the software updated. my car was a newer model 2010 and apparently not under this notification since we did not receive anything from ford. the 'ford customer care' suggested taking the vehicle to another dealer for service who said, "there is nothing we can do.".Mileage was 14000 miles. Vehicle Identification Number (VIN):3FADP0L35AR. Ford Fusion 2010 problem was reported in APPLETON, WI. Vehicle was not using Cruise Control. VEHICLE SPEED: 25 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10386863

FORD FUSION 2010 car safety problem was reported on Mar 07, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . i bought a slightly used (it was a dealer auto) 2010 ford fusion sel. since i first purchased in february 2010, i have experienced very jerky and uneven shifting. i even brought the car back after owning it for about 1 week, but the dealer monaco ford in ct talked me into keeping the car, saying that it is different type of engine (6 cylinder) than i was used to. but it felt wrong and always has. then, i got a recall notice in the mail or service notice notifying me of transmission problems with the make/model of my car. it came from ford and i was instructed to bring the car in for service. i did, but nothing changed. i learned to live with it, but over the past month, the car has become worse and worse - shifting has become so jerky that i experienced severe jolts and whiplash about 5 times. i brought the car in on march 7, 2011 and the transmission is damaged due to a broken front axle seal - i looked online and this seems to be related to the problems with my make/type of vehicle. i need help - i can't afford to keep a car that is not safe. the dealer told me it is not safe to drive and all reports i have read state that these problems are often not fixable - with one problem after another recurring with the transmissions in the affected vehicles. as i bought the car slightly used, i don't think i can sue through the lemon law. i need help! *tr.Mileage was 28000 miles. Ford Fusion 2010 problem was reported in GLASTONBURY, CT. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10389641

FORD FUSION 2010 car safety problem was reported on Oct 14, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . tl* the contact owns a 2010 ford fusion. the contact stated that the rear tire studs fractured several times and were replaced yet the failure consistently recurred. the dealer advised that the failure was not common for a vehicle with such low mileage. the vin was unavailable. the failure mileage was 5,000 and the current mileage was 7,500. .Mileage was 5000 miles. Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in TOPEKA, KS. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Wheels Review #10389940

FORD FUSION 2010 car safety problem was reported on Mar 12, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . i discovered missing lug nuts on two separate wheels on my 2010 ford fusion se. the front passenger side wheel and the rear drivers side wheel. as i looked closer, i noticed that the wheel stud bolt had broken off. i do not know when the wheel studs broke although the one on the rear driver side appears to have happened some time ago as the surface of the break has already corroded. the surface of the break on the front passenger wheel appears to be more recent as there is little to no corrosion. this issue did not cause an accident or any vehicle damage that i am aware of at this time. the vehicle has 17,460 miles on it and was purchased at the end of may 2010. this vehicle is used for personal use - i drive it to and from work which is a 65 mile round trip. *tr.Mileage was 17460 miles. Vehicle Identification Number (VIN):3FAHP0HAXAR. Ford Fusion 2010 problem was reported in PORTAGE, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10391941

FORD FUSION 2010 car safety problem was reported on Jan 20, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . this vehicle was recalled for a known transmission issue in june 2010. ford appears to have reprogrammed the computer to change shift points. shifting is smoother but still it does not perform like a normal ford transmission (i have driven fords since 1964). time out of service was one day. jan 20, 2011 while my wife was driving at approximately 55 mph, the transmission completely disengaged. there was no power and car had to coast to a stop on the side of the road. after sitting for the amount of time that was required for me to reach her i was able to drive the vehicle to the dealership about four miles away. the transaxle seal was leaking and fluid was low. the required parts were on backorder at ford and we had to wait for parts. the vehicle was returned on jan. 31, 2011 (11 days out of service). on feb.12, 2011, the vehicle was being driven by me at approximately 55 mph when the transmission again disengaged. i had to coast to the side of the road and call ford road service for a tow. i parked the vehicle and turned the ignition off. i tried to start the engine to record the mileage and the engine would not run, acting as if the timing was completely out of sync. it bucked and missed fired as if the timing was not correct (i had experienced this once before when starting the vehicle one morning in late sept. 2010 but had not experienced it since that time thought we had gotten some bas gasoline). on both occasions when the transmission has disengaged, the check engine, maintenance required and transmission service required was displayed on the dash by the computer but the dealer claims there was no error code recorded by the computer system. the transmission disengaged again ant highway on march 11, 2011. this is well documented on the web and will cause a death if ford does not correct the problem..Mileage was 14959 miles. Vehicle Identification Number (VIN):3FAHP0HG1AR. Ford Fusion 2010 problem was reported in RALEIGH, NC. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Power Train Review #10391941

FORD FUSION 2010 car safety problem was reported on Jan 20, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . this vehicle was recalled for a known transmission issue in june 2010. ford appears to have reprogrammed the computer to change shift points. shifting is smoother but still it does not perform like a normal ford transmission (i have driven fords since 1964). time out of service was one day. jan 20, 2011 while my wife was driving at approximately 55 mph, the transmission completely disengaged. there was no power and car had to coast to a stop on the side of the road. after sitting for the amount of time that was required for me to reach her i was able to drive the vehicle to the dealership about four miles away. the transaxle seal was leaking and fluid was low. the required parts were on backorder at ford and we had to wait for parts. the vehicle was returned on jan. 31, 2011 (11 days out of service). on feb.12, 2011, the vehicle was being driven by me at approximately 55 mph when the transmission again disengaged. i had to coast to the side of the road and call ford road service for a tow. i parked the vehicle and turned the ignition off. i tried to start the engine to record the mileage and the engine would not run, acting as if the timing was completely out of sync. it bucked and missed fired as if the timing was not correct (i had experienced this once before when starting the vehicle one morning in late sept. 2010 but had not experienced it since that time thought we had gotten some bas gasoline). on both occasions when the transmission has disengaged, the check engine, maintenance required and transmission service required was displayed on the dash by the computer but the dealer claims there was no error code recorded by the computer system. the transmission disengaged again ant highway on march 11, 2011. this is well documented on the web and will cause a death if ford does not correct the problem..Mileage was 14959 miles. Vehicle Identification Number (VIN):3FAHP0HG1AR. Ford Fusion 2010 problem was reported in RALEIGH, NC. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Power Train Review #10391941

FORD FUSION 2010 car safety problem was reported on Jan 20, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . this vehicle was recalled for a known transmission issue in june 2010. ford appears to have reprogrammed the computer to change shift points. shifting is smoother but still it does not perform like a normal ford transmission (i have driven fords since 1964). time out of service was one day. jan 20, 2011 while my wife was driving at approximately 55 mph, the transmission completely disengaged. there was no power and car had to coast to a stop on the side of the road. after sitting for the amount of time that was required for me to reach her i was able to drive the vehicle to the dealership about four miles away. the transaxle seal was leaking and fluid was low. the required parts were on backorder at ford and we had to wait for parts. the vehicle was returned on jan. 31, 2011 (11 days out of service). on feb.12, 2011, the vehicle was being driven by me at approximately 55 mph when the transmission again disengaged. i had to coast to the side of the road and call ford road service for a tow. i parked the vehicle and turned the ignition off. i tried to start the engine to record the mileage and the engine would not run, acting as if the timing was completely out of sync. it bucked and missed fired as if the timing was not correct (i had experienced this once before when starting the vehicle one morning in late sept. 2010 but had not experienced it since that time thought we had gotten some bas gasoline). on both occasions when the transmission has disengaged, the check engine, maintenance required and transmission service required was displayed on the dash by the computer but the dealer claims there was no error code recorded by the computer system. the transmission disengaged again ant highway on march 11, 2011. this is well documented on the web and will cause a death if ford does not correct the problem..Mileage was 14959 miles. Vehicle Identification Number (VIN):3FAHP0HG1AR. Ford Fusion 2010 problem was reported in RALEIGH, NC. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10390430

FORD FUSION 2010 car safety problem was reported on Dec 28, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . 2010 ford fusion transmission flares and hard shifts. have had the car in twice for the same problems including leaking trans fluid from the left front half-shaft. recently the wrench light cam on at the end of a 900 mile trip but went off a day later. i have had a half shaft, clutch, related seals and bushings (took 10 days to repair) replaced before the car reached 21,000 miles. there is a wide spread problem with eh 6f35 transmission used in multiple ford cars and trucks. ford covered the cost of repairs under warranty and only paid for a rental because i bought an extended warranty at purchase. ford is at a loss how to fix these 6f35 transmission problems and is deliberately vague when questioned. i spent $25,000 on this car and am worried about it's safety and durability. i think ford is hoping the warranty runs out before the transmission completely fails. the 6f35 transmissions need replaced. not more computer pcm flashes. i read that on some of the 6f35 transmissions had bore holes manufactured incorrectly. i think ford is trying to cover up this problems and trying cheap fixes that don't resolve the issue. owners all over the internet are having similar issues. *tr.Mileage was 20015 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in LOUISVILLE, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10392373

FORD FUSION 2010 car safety problem was reported on Mar 20, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . found two missing lug nuts/studs from the left rear tire of a 2010 ford fusion. car had only 10,000 miles and the tires/wheels had never been serviced. i found 1 lug nut with the stuud in it laying in my street. stud looks like a clean break not typically associated with overtightening. after insisting, the dealer replaced both. will keep an eye on the rest based on number of complaints found online. *tr.Mileage was 10000 miles. Vehicle Identification Number (VIN):3FAHP0HA9AR. Ford Fusion 2010 problem was reported in CLARKSTON, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Wheels Review #10392499

FORD FUSION 2010 car safety problem was reported on Feb 15, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . tl* the contact owns a 2010 ford fusion. the contact stated that the vehicle would jerk violently. the vehicle was taken to the dealer who stated that the front and rear passenger side wheels were bent and would need to be replaced. the front passenger side wheel was replaced and the dealer stated that the vehicle was safe to drive with the other defective wheel. the manufacturer was contacted who did not offer any assistance since the vehicle was not included in any recalls. the vehicle was not further repaired. the failure and current mileage was 17,229. updated 05/04/11 *bf the consumer stated the vehicle pulled to the left and there was a vibration coming from the vehicle. also, the wheels were bent. updated 07/08/11.Mileage was 17229 miles. Vehicle Identification Number (VIN):3FAHP0KC8AR. Ford Fusion 2010 problem was reported in COLUMBUS, OH. Vehicle was purchased on Mar 13, 2010. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 70 mph. DEALER'S NAME: RICART . DEALER'S TELEPHONE NUMBER: 614-863-6300 .

Ford Fusion 2010 Suspension

Ford Fusion 2010 Suspension Review #10392499

FORD FUSION 2010 car safety problem was reported on Feb 15, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION . tl* the contact owns a 2010 ford fusion. the contact stated that the vehicle would jerk violently. the vehicle was taken to the dealer who stated that the front and rear passenger side wheels were bent and would need to be replaced. the front passenger side wheel was replaced and the dealer stated that the vehicle was safe to drive with the other defective wheel. the manufacturer was contacted who did not offer any assistance since the vehicle was not included in any recalls. the vehicle was not further repaired. the failure and current mileage was 17,229. updated 05/04/11 *bf the consumer stated the vehicle pulled to the left and there was a vibration coming from the vehicle. also, the wheels were bent. updated 07/08/11.Mileage was 17229 miles. Vehicle Identification Number (VIN):3FAHP0KC8AR. Ford Fusion 2010 problem was reported in COLUMBUS, OH. Vehicle was purchased on Mar 13, 2010. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 70 mph. DEALER'S NAME: RICART . DEALER'S TELEPHONE NUMBER: 614-863-6300 .

Ford Fusion 2010 Tires

Ford Fusion 2010 Tires Review #10392682

FORD FUSION 2010 car safety problem was reported on Nov 17, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with TIRES . leased a new 2010 ford fusion on 1/30/10. i had 2 tire issued with this vehicle. flat left rear on about 5/17/11 with 5349 miles which was plugged and a blow out on a highway on about 11/17/2010 which was so bad i had to replace the tire (not over 10,000 miles) i believe there is a problem with this group of tires. *tr.Mileage was 10000 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in WESTPORT, CT. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Seats

Ford Fusion 2010 Seats Review #10394062

FORD FUSION 2010 car safety problem was reported on Dec 31, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SEATS . 2010 ford fusion hybrid front seat headrest/restraint. the front seat headrests protrude forward well past the preferred alignment of the spine. the driver is compelled to operate the vehicle with head pushed forward. this poor ergonomics has resulted in neck and back pain, headaches, and general discomfort. the manufacturer should consider a redesign and make such redesign available to consumers. *tr.Ford Fusion 2010 problem was reported in WALTHAM, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10395173

FORD FUSION 2010 car safety problem was reported on Apr 06, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . tl* the contact owns a 2010 ford fusion. the contact was braking from approximately 5 mph when the engine exhibited an abnormal increase in engine rpms and the transmission became unresponsive. the contact was able to resume driving yet the failure recurred intermittently. the vehicle was taken to an authorized dealer where the contact was awaiting diagnosis of the failure. the failure mileage was approximately 19,500. .Mileage was 19500 miles. Vehicle Identification Number (VIN):3FAHP0JA4AR. Ford Fusion 2010 problem was reported in HOFFMAN ESTATES, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 5 mph.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10395676

FORD FUSION 2010 car safety problem was reported on Apr 11, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . 2010 ford fusion. 19,000 miles. noticed a missing lugnut on 4/11/11. one wheel stud on front driver's side wheel has snapped off. car is currently at the dealer for service. *tr.Mileage was 19000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in ERIE, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 5 CYLINDERS. Ford Fusion 2010 drive type:FWD. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Wheels Review #10395829

FORD FUSION 2010 car safety problem was reported on Dec 22, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . tl* the contact owns a 2010 ford fusion. the contact stated that the openings in the wheels allowed ice to freeze inside and would cause the vehicle to vibrate abnormally. the vehicle was not inspected or repaired for the failure. the manufacturer was not notified. the current mileage was approximately 5,000 and the failure mileage was approximately 2,000. updated 5/9/11 *cn updated 06/06/11.Mileage was 2000 miles. Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in BRUNSWICK, ME. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. DEALER'S NAME: WISCASSED FORD . DEALER'S TELEPHONE NUMBER: 1-80-923-9431 .

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10396539

FORD FUSION 2010 car safety problem was reported on Aug 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . transmission failure and issue persists. occasionally, when accelerating from a stop or a low speed, the transmission will slip and catch violently. the whole car surges and jerks forward causing the tires to chirp. if this were to happen on a day with inclement weather, the car could lose control and cause an accident. ford rebuilt the transmission in summer of 2010 after finding burnt clutch plates. ford has not repaired the original issue after taking the vehicle in 7 times. also, every time the transmission jerks, burning transmission fluid is smelled inside the car through the ac vents. ford claims it is leftover fluid from previous repairs, but after 6 months, the smell is still there. *tr.Mileage was 6000 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in AUSTIN, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:RWD. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Wheels Lugs/nuts/bolts

Ford Fusion 2010 Wheels Lugs/nuts/bolts Review #10396577

FORD FUSION 2010 car safety problem was reported on Apr 17, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS:LUGS/NUTS/BOLTS . i have a 2010 ford fusion se with 12593.2 miles which i purchased new. the wheels have never been removed from the vehicle. before removing the lug nuts of the front drivers' wheel to do a tire rotation, i noticed a lug nut missing. the stud had failed. i am very worried about the remaining studs and have read that others have had similar failures. i will be consulting my dealer monday for a solution. *tr.Mileage was 12593 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in JOHNSON CITY, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Seats

Ford Fusion 2010 Seats Review #10396671

FORD FUSION 2010 car safety problem was reported on July 30, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SEATS . i fully agree with the following previous complaint: 2010 ford fusion hybrid front seat headrest/restraint. the front seat headrests protrude forward well past the preferred alignment of the spine. the driver is compelled to operate the vehicle with head pushed forward. this poor ergonomics has resulted in neck and back pain, headaches, and general discomfort. the manufacturer should consider a redesign and make such redesign available to consumers. this situation is so bad that i have reversed the position of the head rests, thus rendering them totally ineffective. i am unable to drive or ride in this car with the head rests in the normal position. *tr.Mileage was 10 miles. Vehicle Identification Number (VIN):3FADP0L32AR. Ford Fusion 2010 problem was reported in LANCASTER, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD.

Ford Fusion 2010 Service Brakes, Hydraulic

Ford Fusion 2010 Service Brakes, Hydraulic Review #10397306

FORD FUSION 2010 car safety problem was reported on Oct 08, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC . tl* the contact owns a 2010 ford fusion. the contact stated that in cold or snowy weather, the brakes would exhibit a grinding and an increase in stopping distance. the contact believed that the vehicle was not designed for the climate in which he resided. the contact took the vehicle to the dealer and was told that the failure was because of the weather conditions. there were no repairs to the vehicle. the failure mileage was 18,000 and the current mileage was 24,000..Mileage was 18000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in LYON MOUNTAIN, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10398018

FORD FUSION 2010 car safety problem was reported on Mar 27, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . tl-the driver owns a 2010 ford fusion. the driver stated the vehicle would shake violently while accelerating from a stop and rpms would also increase. the vehicle was taken to an authorized dealer who stated the transmission needed to be replaced. the vehicle was not repaired. the failure and current mileages were 20,400. sm..Mileage was 20400 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in CENTERVILLE, SD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Electronic Stability Control

Ford Fusion 2010 Electronic Stability Control Review #10399050

FORD FUSION 2010 car safety problem was reported on June 21, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRONIC STABILITY CONTROL . while driving at various speeds, the vehicle's engine would shutdown and all power assist features would be disengaged. the check engine, check traction control, check oil pressure, check temperature, and low fuel warning messages would illuminate. the vehicle suffered from these symptoms approximately 13 times over the course of 1000 miles ultimately resulting in several evasive maneuvers to avoid collisions caused by the lack of engine power. the vehicle spent 27 days in the shop and ultimately the main ecm was replaced. the symptoms have since ceased, but i am concerned that they may start again since the system failures seemed to increase with 100+ degree ambient air temperatures..0 person(s) were injured. 0 person(s) died.Mileage was 2300 miles. Vehicle Identification Number (VIN):3FADP0L3XAR. Ford Fusion 2010 problem was reported in SAN ANTONIO, TX. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10399050

FORD FUSION 2010 car safety problem was reported on June 21, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . while driving at various speeds, the vehicle's engine would shutdown and all power assist features would be disengaged. the check engine, check traction control, check oil pressure, check temperature, and low fuel warning messages would illuminate. the vehicle suffered from these symptoms approximately 13 times over the course of 1000 miles ultimately resulting in several evasive maneuvers to avoid collisions caused by the lack of engine power. the vehicle spent 27 days in the shop and ultimately the main ecm was replaced. the symptoms have since ceased, but i am concerned that they may start again since the system failures seemed to increase with 100+ degree ambient air temperatures..0 person(s) were injured. 0 person(s) died.Mileage was 2300 miles. Vehicle Identification Number (VIN):3FADP0L3XAR. Ford Fusion 2010 problem was reported in SAN ANTONIO, TX. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10400071

FORD FUSION 2010 car safety problem was reported on May 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . while pulling out of the driveway a neighbor noticed a lug nut fall off my vehicle. i stopped the car immediately and we determined that the car was missing 2 lug nuts, one from each front tire. we went to make sure the remaining lug nuts were securely attached and when applying a slight amount of pressure to another lug nut it snapped off. this happened with two nuts. the inside stud that the lug nut attached to looks as if the metal is crumbled. the vehicle has 13600 miles on it and has had the tires rotated once at 6600 miles by the ford dealership we purchased the car from. this is well within the standards the warranty requires (at 7500 and 15000).0 person(s) were injured. 0 person(s) died.Mileage was 13600 miles. Vehicle Identification Number (VIN):3FAHP0HG8AR. Ford Fusion 2010 problem was reported in BROOMFIELD, CO. Vehicle was not using Cruise Control. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10400176

FORD FUSION 2010 car safety problem was reported on Apr 27, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while traveling at highway speed on a 4-lane divided highway, a slow-moving vehicle merged in front of our fusion forcing a hard braking event (there was somebody coming up from behind in the left lane, preventing a lane change at that instant). the fusion was slowed down to 50-55 mph as the car from behind passed. this allowed a lane change to avoid hitting the car that pulled in front to begin with. however, in order to keep up with the flow of traffic, 100% accelerator pedal was required. as the fusion accelerated up to near the original speed, there was a whining sound coming from under the hood, then a violent jolt. this jolt severely shook the car, caused a sudden deceleration and to swerve on the highway. luckily, my wife was able to keep control of the car. the seat belt grabbed. had my wife not been wearing the seat belt, she is convinced that she would have been thrown into the steering wheel. the car was taken to a nearby ford dealership. no problems were found. (however, a fault code specific to hybrid vehicles was logged in the pcm memory.) this appears to be a continuation of the transmission problems this car has been experiencing since the day after i purchased the car in august, 2010 - and ford has been unable to correct. this vehicle has been into the ford dealer numerous times for transmission issues. the car is now at my local dealership..0 person(s) were injured. 0 person(s) died.Mileage was 11900 miles. Vehicle Identification Number (VIN):3FAHP0JG8AR. Ford Fusion 2010 problem was reported in GREENSBORO, NC. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10399925

FORD FUSION 2010 car safety problem was reported on May 10, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . i bought my 2010 ford fusion approximately 18 months ago, have had the transmission broken down, rebuilt reprogrammed and am now being told they can find nothing wrong with my car. however, seeing how i am the one who has narrowly escaped several highly dangerous collisions on both streets and highways i find it really hard to believe nothing is wrong with my transmission. while driving the transmission will get stuck while shifting from one gear to the next, usually but not limited to 2nd, 3rd & 4th gear and will sometime slip gears when transitioning from reverse to drive. i have taken my car in four times now and am continually told they can find nothing wrong with the transmission. these highly dangerous transmission misfires happen every day i drive my car, no matter the driving condition. *tr.Mileage was 27000 miles. Vehicle Identification Number (VIN):3FAHP0HAXAR. Ford Fusion 2010 problem was reported in FULLERTON, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Steering

Ford Fusion 2010 Steering Review #10402306

FORD FUSION 2010 car safety problem was reported on May 11, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with STEERING . 2010 ford fusion steering problem - car pulls to the left or sometimes right. usually when traveling at lower speeds the steering is terrible, it wants to pull the wheel hard to one side, always happens on uneven road surface - sometimes on even roads - every one of my other cars drive perfect on the same road. took my company car to the dealer to have it looked at - they replaced all 4 tires and did an alignment - charged my fleet $1,200 and it still does the same thing. service manager said that it is a characteristic of the car and ford will not fix it - just live with it. problem is i am stuck with it for another year and a half... *tr.Mileage was 1 miles. Ford Fusion 2010 problem was reported in JAMISON, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 25 mph.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10402309

FORD FUSION 2010 car safety problem was reported on May 22, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . during a long trip back from a weekend vacation i felt my front drivers side wheel begin to wobble. when i pulled over to check it out i noticed that i only had 3 lugnuts holding the wheel on. i also noticed a third that looked loose. when i grabbed it, it fell out in my hand with the stud broken off in the lugnut. the other 2 missing lugnuts spots also had studs broken off. the rear drivers side wheel had also lost a lugnut and had a broken stud. *tr.Mileage was 22000 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in ASHLAND, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Equipment

Ford Fusion 2010 Equipment Review #10402592

FORD FUSION 2010 car safety problem was reported on Apr 25, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with EQUIPMENT . my vehicle came with the standard cloth floor mats, but my dealer "threw in" the factory rubber ones from another fusion free of charge. i've had my vehicle a little over a year now and twice i have had a sticking accelerator pedal. the floor mat creeps forward and will sometimes catch the accelerator pedal just right and keep the pedal at whatever throttle setting it was last at. this has never caused any real problems for me, but i feel that it is important that ford mo co be made aware of this and either encourage dealers to not exchange the floor mats, or to install some sort of holding mechanism to keep the rubber mats from interfering with the accelerator pedal. *tr.Mileage was 18000 miles. Vehicle Identification Number (VIN):3FADP0L3XAR. Ford Fusion 2010 problem was reported in SAN ANTONIO, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10403923

FORD FUSION 2010 car safety problem was reported on May 25, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . i have a 2010 ford fusion that i bought in june 2009. since day one i have had transmission problem. transmission would slip going to second to third . upon hard acceleration like merging onto a highway the transmission would slip and the rpms would go to redline. the car would not move. this was a very dangerous situation. car was brought to dealer on 11/13/2009 and the dealer said it was a computer problem. they reprogrammed it. on 2/23/2010 car was brought back for same problemdealer replaced transmission. 6/2010 received a recall notice from ford saying there was a computer problem with the transmission. reprogrammed again. went back to the dealer numerous times after new transmission was installed with the same problems as mentioned before.on 5/24/2011 dealer rebuilt the new transmission. on 5/25/2011 complained to dealer saying i have the same problem.5/31/2011 car is back at dealer transmission will not shift. this car is extremely dangerous especially merging onto the highway. *tr.Vehicle Identification Number (VIN):3FAHP0JG4AR. Ford Fusion 2010 problem was reported in BARNEVELD, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10405277

FORD FUSION 2010 car safety problem was reported on May 06, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . as i was passing another vehicle, the vehicle lost power and a warning light illuminated telling me to pull over immediately. luckily i was able to make it to the side of the highway. the codes pulled were p0010, p0201, p0202, p0203, p0204. the dealer checked the electrical connections and reassembled. the issue happened again on 5/30/11 as i was driving on the highway. the same codes as the first incident was found with an additional code of p1a03. again the dealer checked the electrical connections and reassembled. i feel this is a safety issue because when you are driving along on the highway the cars around you do not expect you to dramatically slow down. if you manage to safely make it to the side of the road without being in an accident or causing an accident you still face another safety issue being stuck on the side of the road with traffic going by at 65 mph..0 person(s) were injured. 0 person(s) died.Mileage was 5970 miles. Vehicle Identification Number (VIN):3FADP0L30AR. Ford Fusion 2010 problem was reported in STATE COLLEGE, PA. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Unknown Or Other

Ford Fusion 2010 Unknown Or Other Review #10405277

FORD FUSION 2010 car safety problem was reported on May 06, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with UNKNOWN OR OTHER . as i was passing another vehicle, the vehicle lost power and a warning light illuminated telling me to pull over immediately. luckily i was able to make it to the side of the highway. the codes pulled were p0010, p0201, p0202, p0203, p0204. the dealer checked the electrical connections and reassembled. the issue happened again on 5/30/11 as i was driving on the highway. the same codes as the first incident was found with an additional code of p1a03. again the dealer checked the electrical connections and reassembled. i feel this is a safety issue because when you are driving along on the highway the cars around you do not expect you to dramatically slow down. if you manage to safely make it to the side of the road without being in an accident or causing an accident you still face another safety issue being stuck on the side of the road with traffic going by at 65 mph..0 person(s) were injured. 0 person(s) died.Mileage was 5970 miles. Vehicle Identification Number (VIN):3FADP0L30AR. Ford Fusion 2010 problem was reported in STATE COLLEGE, PA. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Fuel System, Gasoline

Ford Fusion 2010 Fuel System, Gasoline Review #10405292

FORD FUSION 2010 car safety problem was reported on June 05, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE . my 2010 fusion has experienced multiple issues with the check engine light. it is always the same pcm code of p0456 which deals with evaporative emissions system. the servicing dealer does not know where the problem is nor how to fix it- even after calling tech support and having a field service engineer assigned. while the light is on, making left hand turns is downright frightful as the engine loses power and the car feels as if it does not want to go. one would think that after five repair attempts in 14 months the issue would be corrected. this last time it took less than three days and 122 miles for the issue to reappear. there is a tsb for the issue but apparently that did not fix my vehicle. *tr.Mileage was 22329 miles. Vehicle Identification Number (VIN):3FAHP0JG1AR. Ford Fusion 2010 problem was reported in NEW BOSTON, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10406383

FORD FUSION 2010 car safety problem was reported on June 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . 2010 ford fusion. consumer states issues with ford's g speed auto trans found in fusion 2010 model *tgw the consumer stated the transmission popped out of gear on four occasions while driving on the freeway. there was also a bearing noise coming from the vehicle and a throttle hesitation which the dealer couldn't identify. *jb.Ford Fusion 2010 problem was reported in REDLANDS, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10405616

FORD FUSION 2010 car safety problem was reported on June 07, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. while attempting to park traveling 2 mph, the contact stated that the vehicle suddenly accelerated without warning, causing her to crash into a concrete barrier. she was able to apply pressure to the brakes and shift into park to bring the vehicle to a stop. the dealer or manufacturer had not been notified nor was the vehicle repaired. the current and failure mileages were 12,815. a police report was not filed. .Vehicle was involved in a crash. Mileage was 12815 miles. Vehicle Identification Number (VIN):3FADP0L35AR. Ford Fusion 2010 problem was reported in MOUNT VERNON, WA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 2 mph.

Ford Fusion 2010 Air Bags

Ford Fusion 2010 Air Bags Review #10405755

FORD FUSION 2010 car safety problem was reported on June 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with AIR BAGS . tl*the contact owns a 2010 ford fusion hybrid. a vehicle crashed into the drivers side of the contacts vehicle and the air bag did not deploy. there were no injuries. a police report was filed. the dealer and manufacturer were contacted and stated that since his insurance was investigating the situation, they could not offer any assistance. the vehicle was towed to a holding station and was not repaired. the failure and current mileage was 37,000. .Vehicle was involved in a crash. Mileage was 37000 miles. Vehicle Identification Number (VIN):3FADP0L36AR. Ford Fusion 2010 problem was reported in LAKE WORTH, FL. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10406966

FORD FUSION 2010 car safety problem was reported on May 08, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . traveling at high speed with cruise control on. applied brake to slow down for traffic, vehicle continued to slow and would not respond when i applied the accelerator. i had to put the transmission in neutral and had to push gas pedal several times hard before engine would respond. this happened twice while traveling from florida to canada. i had the ford dealership in wetaskiwin, alberta, canada check the vehicle, they could find nothing wrong. i continue to drive the car, but i am fearful that, if it happens again, i could be rear-ended. *tr.Mileage was 10000 miles. Vehicle Identification Number (VIN):3FAHP0JA7AR. Ford Fusion 2010 problem was reported in PARRISH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 75 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10406966

FORD FUSION 2010 car safety problem was reported on May 08, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . traveling at high speed with cruise control on. applied brake to slow down for traffic, vehicle continued to slow and would not respond when i applied the accelerator. i had to put the transmission in neutral and had to push gas pedal several times hard before engine would respond. this happened twice while traveling from florida to canada. i had the ford dealership in wetaskiwin, alberta, canada check the vehicle, they could find nothing wrong. i continue to drive the car, but i am fearful that, if it happens again, i could be rear-ended. *tr.Mileage was 10000 miles. Vehicle Identification Number (VIN):3FAHP0JA7AR. Ford Fusion 2010 problem was reported in PARRISH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 75 mph.

Ford Fusion 2010 Tires

Ford Fusion 2010 Tires Review #10407461

FORD FUSION 2010 car safety problem was reported on June 19, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with TIRES . tl*the contact owns a 2010 ford fusion with michelin energy saver tires p225/ 50 r17. the contact stated while traveling 60 mph the rear drivers side tire blew out. the contact replaced the tire with spare tire and was able to drive to home. the failure was not diagnosed by a dealer. the contact was concerned, since there was not a lot of mileage on the vehicle. the failure and current tire mileage was 15,500..Mileage was 15000 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in FORDS, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Tires Review #10409106

FORD FUSION 2010 car safety problem was reported on June 27, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with TIRES . i purchased a new 2010 ford fusion and have been having issues with one tire losing air for several months now but they had been unable to find the leak until recently. finally after going to two tire centers on friday they were able to find that, as i understand it, there is a defect in the tire/rim that caused an indent in the tire at the inner bead that caused a slow seeping leak. i have a statement from the owner of that tire center that in no way would a seal be a permanent fix. i then had to take it into the ford service center were it was confirmed that the beads were not sealing to the actual rim. a bead seal was done on all four tires but neither the tire or the rim was replaced. i requested a new tire but was told that this was what was being done for this problem and to come back if the problem continues. i have read other complaints about this problem and statements that others have even experienced blow-outs at very low mileage. i have a 16 year old daughter with a learner's permit and am very concerned about her driving this vehicle. she needs driving hours on the highway but this is going to be very difficult to do since i am worried about there being a problem with my tires. this is a vehicle that we had planned on possibly passing down to her, but if there is not a recall on this before then, we may have to purchase new tires and rims just to feel comfortable doing so. i don't think that we should have to pay to replace four tires and rims after purchasing a brand new vehicle, at just approximately 12,000 miles. *tr.Ford Fusion 2010 problem was reported in THORNTON, CO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10410150

FORD FUSION 2010 car safety problem was reported on June 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . multiple fractures of wheel studs on 2010 ford fusion, creating very dangerous situation. one failure was four studs at once, leaving only one stud available to prevent complete failure and loss of control. *tr.Ford Fusion 2010 problem was reported in GRAND JUNCTION, CO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Visibility

Ford Fusion 2010 Visibility Review #10410899

FORD FUSION 2010 car safety problem was reported on June 10, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY . tl* the contact owns a 2010 ford fusion. the contact stated the windshield cracked fourteen inches from the passenger side. the windshield was installed and repaired by a glass company. the contact was responsible for paying $800 to repair the vehicle. a year later, the windshield cracked again in the same place. the vehicle was taken to the dealer who stated there were no recalls and offered no assistance. the manufacturer was not contacted. the failure mileage was 1,500. .Mileage was 1500 miles. Vehicle Identification Number (VIN):3FAHP0JA8AR. Ford Fusion 2010 problem was reported in ARVADA, CO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Unknown Or Other

Ford Fusion 2010 Unknown Or Other Review #10412490

FORD FUSION 2010 car safety problem was reported on May 18, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with UNKNOWN OR OTHER . engine hesitates from a stop and bucks and jerks while driving. hard pick-up. rpm's up to max without vehicle acceleration. feels like transmission slips into neutral. first visit, 5/18/2010 (8767 miles-bought new at 15 miles-10/10)/ presently, july, 2011, car with 22,000 is in for 4th return to dealer: 10/2010 car 1 year old, 14,000 miles, local oil repair shop notices both lower ball joints boots split, returned to dealer to resolve. still hesitating and jerking and bucking, particularly during gear shifts. second visit, 11/2010 returned for same driving problems. third visit 6/30/11 service shop notices leak under carriage, returned to dealer. service manager and i check under carriage, still obvious leak, he told me it wasn't a leak, we both had grease/oil/something on our hands. refused to extend rental car coverage as car is "completely fixed", left with car, wrote on ticket, "leak still unresolved". returned for forth visit 7/8/2011 admits leak "somewhere". also, sealant around windshield melts and becomes tacky in hot weather (texas). had dealer reseal last summer. now, area is getting tacky again. will this occur each summer and will seal hold during hard rain? .Mileage was 8767 miles. Vehicle Identification Number (VIN):3FAHP0JAXAR. Ford Fusion 2010 problem was reported in ROUND ROCK, TX. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10412490

FORD FUSION 2010 car safety problem was reported on May 18, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . engine hesitates from a stop and bucks and jerks while driving. hard pick-up. rpm's up to max without vehicle acceleration. feels like transmission slips into neutral. first visit, 5/18/2010 (8767 miles-bought new at 15 miles-10/10)/ presently, july, 2011, car with 22,000 is in for 4th return to dealer: 10/2010 car 1 year old, 14,000 miles, local oil repair shop notices both lower ball joints boots split, returned to dealer to resolve. still hesitating and jerking and bucking, particularly during gear shifts. second visit, 11/2010 returned for same driving problems. third visit 6/30/11 service shop notices leak under carriage, returned to dealer. service manager and i check under carriage, still obvious leak, he told me it wasn't a leak, we both had grease/oil/something on our hands. refused to extend rental car coverage as car is "completely fixed", left with car, wrote on ticket, "leak still unresolved". returned for forth visit 7/8/2011 admits leak "somewhere". also, sealant around windshield melts and becomes tacky in hot weather (texas). had dealer reseal last summer. now, area is getting tacky again. will this occur each summer and will seal hold during hard rain? .Mileage was 8767 miles. Vehicle Identification Number (VIN):3FAHP0JAXAR. Ford Fusion 2010 problem was reported in ROUND ROCK, TX. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10412036

FORD FUSION 2010 car safety problem was reported on July 12, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . 2010 ford fusion transmission slip. had software up date done diden't fix it. had valvabody replaced diden't fix it after the third attempt at a repair i wanted ford to replace the complete transmission they would not. they rebuilt it, it was better but not like i thought it should be. now it is making a noise again and the ford tech can't hear it. ford needs to make good on their product my fusion is about to be out of warrantee then what will i do i don't have money for a new transmission every 6mo. *tt .Ford Fusion 2010 problem was reported in GA, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train Automatic Transmission Review #10412078

FORD FUSION 2010 car safety problem was reported on July 12, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . transmission is acting very erratic. the transmission "flares" causing rpms to go up quickly regardless of throttle position. it also shudders while driving highway speeds, almost as if searching between gears while maintaining a steady speed. also, it shifts very roughly, comparable to an inexperienced driver operating a manual transmission, and these abrupt shifts cause the car to want to accelerate. i have heard reports of people having the transmission completely fail while cruising at highway speeds, and being a father of two little ones, want to see to it this problem gets fixed. ford denies there are any problems, yet a bit of research shows there are multiple lemon law suits against the 2010 ford fusion. i have not yet taken it to a dealership as i have heard there really is no solution to the problems, and those who have have not seen any improvement. in fact, many have reported complete transmission failure from the so-called "fixes". *tt.Mileage was 24000 miles. Vehicle Identification Number (VIN):3FAHP0JG2AR. Ford Fusion 2010 problem was reported in ELGIN, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10412103

FORD FUSION 2010 car safety problem was reported on Feb 15, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . i have had several issues with my 2010 ford fusion transmission sel v6. i've taken it to the dealership several times. they finally did a reprogram dec 09, 2010 with 8k miles. then complete transmission rebuild 2/15/11 with 11k miles on it. now i'm experiencing the same problems yet again at 16k. i have to take it right back to the dealership. they always tell me nothing is wrong. the trans has to adapt to my driving again. why is the car shutting off? transmission surging gears, not picking up, car bucking in the morning when going from park to drive. it's been terrible. i hate driving in rush hour because i never know what my car is going to do. every time i take it to the dealership they say nothing is wrong. i'm sick of paying $30 a day for repeated transmission issues. it's out of hand and unsafe. i have a toddler in my car. this is the whole reason i buy new cars...so that i never worry about being stranded and i feel safe with my baby in the car. this is the worst car i've ever owned. *tr.Mileage was 8843 miles. Vehicle Identification Number (VIN):3FAHP0JG8AR. Ford Fusion 2010 problem was reported in OAK PARK, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 5 mph.

Ford Fusion 2010 Fuel System, Other

Ford Fusion 2010 Fuel System, Other Review #10412172

FORD FUSION 2010 car safety problem was reported on July 12, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, OTHER . 1. engine check light and telltale "wrench" light illuminate. while driving in hot whether the above occurred 5 times in a 54 mile trip. once illuminated, the car has no throttle response and idles at 1000 rpm (limp mode as described by ford). the 'limp mode' does not provide enough power to pull over and stop safely out of traffic. in odor to have the eprom reset, the operator must place the car in park; turn off the engine for approx. 2 minutes. i found that turning off the ac, thereby reducing the ambient temperature in the engine compartment, that the condition resolved itself long enough to deliver the car to the dealership for diagnostics. dealership found that the 'throttle body" unit was faulty. initially, i was informed that this would be covered by warranty. now ford has changed the stated 'covered under warranty" statement. subsequently, the 'throttle body' units are on back order for 10-12 days. sounds like this occurring frequently to "throttle bodies" with no stock and back ordered. bottom line ford may need to investigate and prepare for a recall. *tr.Mileage was 52500 miles. Vehicle Identification Number (VIN):3FAHP0HG9AR. Ford Fusion 2010 problem was reported in LAWRENCEVILLE, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10412220

FORD FUSION 2010 car safety problem was reported on Apr 19, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . erratic shifting. slipping clutches. holds onto gears with no shift. acceleration hesitation. extreme at times. twice, while attempting to accelerate and merge onto expressway, the engine dropped to almost idle for over a second. when the engine did catch it went to red line so quickly had to let up on the accelerator. this further confused the trans. nearly got rear ended but was not only because of the quick reaction of the other drivers. software has been reloaded twice. not any better. ford keeps promising a fix is coming. been waiting over a year. *tr.Mileage was 28000 miles. Vehicle Identification Number (VIN):3FAHP0CG5AR. Ford Fusion 2010 problem was reported in ROYAL OAK, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 25 mph.

Ford Fusion 2010 Service Brakes, Hydraulic

Ford Fusion 2010 Service Brakes, Hydraulic Review #10413128

FORD FUSION 2010 car safety problem was reported on July 14, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC . poor brake response on 2010 ford fusion sport awd. when attempting to slow the vehicle in an emergency stopping situation, the brakes do not produce enough friction between the pads and rotors, thus does not activate abs unless on slippery or snow surface. the brakes do not have enough force to stop the vehicle in an emergency. *tt.Mileage was 26322 miles. Vehicle Identification Number (VIN):3FAHP0DC5AR. Ford Fusion 2010 problem was reported in DENVER, CO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:AWD. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10414241

FORD FUSION 2010 car safety problem was reported on July 03, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . own a 2010 ford fusion se with 24v 3.0 v6 with 6 speed select shift transmission. when car was new, had hard shifts, and in mid 2010 ford issues a recall to reprogram these issues. after this repair, dealership stated they ran a load test and the transmission was fine. in late 2010, the hard shifts returned and the dealership "reprogrammed" the transmission. in late june 2011 while on a road trip, received a transmission/drive train code (the wrench symbol) but no noticeable issues. approximately one week later, started getting hard shifts. the next day, as i was pulling on a major road way, the transmission dropped out of gear, engine acted it was in neutral, and the car came to a complete stop. when i was able to get the car moving, it was revving poorly, shifting extremely hard, and had a terrible vibration. had the car at the dealership for two days, they had a very hard diagnosing the issue (even though the system sent codes). they reprogrammed the transmission, and said the issue was fixed. today, five days later, the issues returned, but worse. every time the vehicle was at a stop, as you would begin to accelerate, the car would shudder and rev to 7000 rpm. you have to completely let off the throttle, and once it would drop to about 1500 rpm, and the transmission would reengage. in gear 5 or 6 at speed, it would try and down shift and would kick out of gear and rev to close to red line. i was almost rear ended on several occasions today as i was trying to get the vehicle home. as i've researched the issue, this seems to be a common issue with several near accidents..0 person(s) were injured. 0 person(s) died.Mileage was 24000 miles. Vehicle Identification Number (VIN):3FAHP0HG2AR. Ford Fusion 2010 problem was reported in MYERSTOWN, PA. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10415911

FORD FUSION 2010 car safety problem was reported on July 24, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . i was driving on the freeway 101. i accelerated to change lanes and the gas pedal stuck in that position. i put on the brakes to slow me down as soon as i took my foot off the brake the car started to speed again, i braked again and exited the freeway and pulled to the side of road, put it in neutral and turned of the engine. when i looked at the gas pedal, the rubber mat had stuck on top of the accelerator. i called my ford dealer today they had no knowledge of this problem, however i noted on the web today you had issued a warning about this problem in june of 2010, we bought our car in oct. 2010, and i guess ford didn't tell dealers not to put this all weather mat on top of an existing mat, as per their printed instructions on the mat itself. .Vehicle Identification Number (VIN):3FADP0L32AR. Ford Fusion 2010 problem was reported in CANOGA PARK, CA. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10415221

FORD FUSION 2010 car safety problem was reported on July 25, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . while driving on the highway, my car suddenly slipped gears on its own and started to slow down and the wrench light was illuminated. i was nearly rear ended and i had my children in the car with me. i managed to make it to the emergency lane and at that point the car thrusted forward and jerked. i put it in park and turned it off and back on and light was gone. the next day while driving to work on highway again, same problem. i took it to local ford that evening only to get a phone call that they cant duplicate the problem. i told them of the numerous complaints i found online about this problem and that i didn't feel safe leaving the lot. they said they haven't heard of any complaints nor any tsbs on this car! i sent them a link to this website and told them to read it. currently they have not called me back with an answer. i bought this car with about 25,000 miles on it 3 months ago and currently i am at 29,700. i surely didn't expect to have a major issue like this. i own another ford which has lasted well over 200k miles but i have never been placed in danger with any vehicle like this. the dealership told me when the car does that it goes into limp mode for "safety' reasons. i don't see how safe that can be if you cause a pile up on the freeway. my question i am waiting to ask them is even if they drove my car and got the same issue, if the read out on machine doesn't tell them what's wrong, how are they to fix it? will they still say nothing was wrong because they computer can't duplicate it? or do they think i like being without a vehicle and wasting everyone's time? *tr.Mileage was 29690 miles. Vehicle Identification Number (VIN):3FAHP0HGXAR. Ford Fusion 2010 problem was reported in SAN ANTONIO, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10415406

FORD FUSION 2010 car safety problem was reported on July 26, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . the wrench warning light comes on in my 2010 ford fusion most of the time it is after it has been driven for awhile then shut off and restarted soon after but yesterday it happened as i was driving the car loses power will only go about 35 mph no matter how far you push the accelerator when trying to ascend a steep hill it would only go 10 miles per hour. *tr.Mileage was 31035 miles. Vehicle Identification Number (VIN):3FAHP0HA2AR. Ford Fusion 2010 problem was reported in GEORGETOWN, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10415485

FORD FUSION 2010 car safety problem was reported on July 27, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . throttle body went bad on my 2010 ford fusion v6 after only having 45,000 miles on it. on vehicle not even 2 years old; a part this important shouldn't fail. *tr.Mileage was 45000 miles. Ford Fusion 2010 problem was reported in CUMMING, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10416653

FORD FUSION 2010 car safety problem was reported on July 18, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . tl* the contact owns a 2010 ford fusion. the contact stated that the front driver side lug nut detached from the wheel. neither the dealer nor the manufacturer were notified of the failure nor was the vehicle inspected or repaired. the current and failure mileages were 33,000. .Mileage was 33000 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in DIAMOND BAR, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10418341

FORD FUSION 2010 car safety problem was reported on Aug 08, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . i have a 2010 ford fusion 4cyl automatic with 20k miles. i have had transmission issues since i purchased this car in 2010. i am experiencing choppy and jerky shifting. when driving at low speeds in traffic the car will shift and jerk forward. also, when shifting from reverse to forward, the car will sometimes violently jerk forward. i took the car in about 8 months ago and the technician couldn't get the issues to repeat and told me there was nothing wrong. i am now complaining since i noticed this is a well known issue and ford is ignoring it. *tr.Mileage was 5000 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in PALATINE, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10419175

FORD FUSION 2010 car safety problem was reported on Aug 10, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . 2010 ford fusion studs breaking off. second time in 4 months. *tr .Mileage was 30000 miles. Vehicle Identification Number (VIN):3FAHP0HA4AR. Ford Fusion 2010 problem was reported in TARENTUM, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Unknown Or Other

Ford Fusion 2010 Unknown Or Other Review #10420254

FORD FUSION 2010 car safety problem was reported on July 02, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with UNKNOWN OR OTHER . to begin with i was only having problems when shifting from reverse to forward. i took my car in for the recall and i am still having problems: my car will jerk violently and then slow down to 0. the wrench light comes on and sometimes the transmission light. it has happened going slow as in making a turn, going fast, and going slow in a straight pattern. i have documented the gas because the service tech said it might not be the transmission but something with the fuel. it happens on full, 3/4, half and a quarter of a tank, early morning, after i have driven it for a while. yesterday it happened 4 times in 4 miles each time i have to shut the engine off, which apparently resets it, because the lights will go off, but then come on when it happens again. this car is dangerous to drive, someone is going to be killed. i have advised my family that if i am rear-ended and death occurs to seek legal council. the service people say they can not do anything unless they can get the car to mimic the problem, or something shows up on the computer. meanwhile this is my only means of transportation, i also use my car everyday for business. they have not provided me with an alternate means of transportation yet want to keep my car for 4 days. please do something, there are complaints all over the internet, i am sure you would have more complaints if people knew about you. can you pull ford's service records to get a more accurate record of the magnitude of problems. do something before someone dies. .Vehicle Identification Number (VIN):3FAHP0JG7AR. Ford Fusion 2010 problem was reported in SEMMES,, AL. Vehicle was not using Cruise Control. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10420254

FORD FUSION 2010 car safety problem was reported on July 02, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . to begin with i was only having problems when shifting from reverse to forward. i took my car in for the recall and i am still having problems: my car will jerk violently and then slow down to 0. the wrench light comes on and sometimes the transmission light. it has happened going slow as in making a turn, going fast, and going slow in a straight pattern. i have documented the gas because the service tech said it might not be the transmission but something with the fuel. it happens on full, 3/4, half and a quarter of a tank, early morning, after i have driven it for a while. yesterday it happened 4 times in 4 miles each time i have to shut the engine off, which apparently resets it, because the lights will go off, but then come on when it happens again. this car is dangerous to drive, someone is going to be killed. i have advised my family that if i am rear-ended and death occurs to seek legal council. the service people say they can not do anything unless they can get the car to mimic the problem, or something shows up on the computer. meanwhile this is my only means of transportation, i also use my car everyday for business. they have not provided me with an alternate means of transportation yet want to keep my car for 4 days. please do something, there are complaints all over the internet, i am sure you would have more complaints if people knew about you. can you pull ford's service records to get a more accurate record of the magnitude of problems. do something before someone dies. .Vehicle Identification Number (VIN):3FAHP0JG7AR. Ford Fusion 2010 problem was reported in SEMMES,, AL. Vehicle was not using Cruise Control. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10419734

FORD FUSION 2010 car safety problem was reported on Apr 28, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . several months ago, the rear left wheel of m y 2010 fusion was falling off. i managed to stop, tow and fix the car. in april, my passenger right wheel fell off causing me to lose control, hit a pole and total my 7 month old vehicle. i was issued numerous tickets and lost my job due to this accident. one month later, ford contacts me to reimburse me for the first episode (i received the check), but took no blame for any of the problems with my vehicle. i was told my car was listed in the recall from ford. afterward i found out that there are many other complaints for my ford fusion. *kb.Vehicle was involved in a crash. Mileage was 22200 miles. Vehicle Identification Number (VIN):3FAHP0HA2AR. Ford Fusion 2010 problem was reported in NORTH BRUNSWICK, NJ. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10420089

FORD FUSION 2010 car safety problem was reported on July 09, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . the transmission slams into reverse when cold, slips between gears, seems to pop into neutral, rpm shoots to over 4000, slams back into gear so hard you'd swear the car has been rear-ended. the "wrench" warning light illuminated on the instrument panel. the dealer performed tsb to replace the pcm computer--didn't help. the car did the same thing as i drove it home from the dealer. this is in no way a complaint about our dealer. this service department always gives us great service, and are willing to do anything they can to help us, but what are they supposed to do? they didn't design or build this monstrosity. they are in contact with ford factory engineers to try to solve this problem, but no answers are forthcoming. we are afraid to stray far from home with this fusion. if we can't just go anywhere we want with the car, what good is it to us? the internet is awash with horror stories about this defective transmission. this is a known issue. as of this writing, there are over 60 complaints on this nhtsa site about this exact problem. how many more are needed before the agency takes some action? *kb.Mileage was 39725 miles. Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in VACAVILLE, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Wheels Lugs/nuts/bolts

Ford Fusion 2010 Wheels Lugs/nuts/bolts Review #10420116

FORD FUSION 2010 car safety problem was reported on June 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS:LUGS/NUTS/BOLTS . tl* the contact owns a 2010 ford fusion. the contact stated the passenger side front and drivers side vehicle studs were broken and replaced at multiple times. the vehicle was not taken to the dealer, and the manufacturer was not notified. the vehicle was not repaired. the failure mileage was 43,000 and the current mileage was 50,000. .Mileage was 43000 miles. Vehicle Identification Number (VIN):3FAHP0HG1AR. Ford Fusion 2010 problem was reported in LEESBURG, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10421467

FORD FUSION 2010 car safety problem was reported on Aug 25, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . ford 6f35 transmission has "dead spots", jerkiness and hard shifting since i owned the car. at 56,500 miles, transmission fluid was found to be leaking from the drive shaft axle and that had to be replaced under warranty. the transmission in this car is defective and should be replaced. *tr.Mileage was 56500 miles. Vehicle Identification Number (VIN):3FAHP0JG3AR. Ford Fusion 2010 problem was reported in MEBANE, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 25 mph.

Ford Fusion 2010 Latches/locks/linkages

Ford Fusion 2010 Latches/locks/linkages Review #10422359

FORD FUSION 2010 car safety problem was reported on Aug 23, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with LATCHES/LOCKS/LINKAGES . 2010 ford fusion purchased in december 2010 continues to have the hood released when driving. the vehicle has been taken back to pauli ford many times since i owned the car.....without success in fixing the problem, i have informed pauli ford/st. johns michigan and also ford motor co. of the problem and that my concern is that while driving an accident may occur. the last date the hood opened is below but the problem has continued since the vehicle was owned. *tr.Mileage was 26150 miles. Vehicle Identification Number (VIN):3FAHP0JG6AR. Ford Fusion 2010 problem was reported in ST. JOHNS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10422440

FORD FUSION 2010 car safety problem was reported on Aug 27, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while driving down a very busy road at 45 mph, my accelerator cut out, reducing engine power to idle and causing me to almost be hit by 3 different vehicles while trying to find a place to stop. i had my wife and my infant son in the car. this was unacceptable for a vehicle this new! the maintenance light (wrench) came on..but went off after i shut the vehicle down and restarted, to which the car then ran normal. i then had it accelerate uncommanded, at that point a shut it down and had it towed to the dealership. i am waiting to hear what they say about it. 37,000 miles seems terribly low to be having these types of "issues" it is a 2010 ford fusion se 3.0l, and i am not happy! *tr.Mileage was 37700 miles. Vehicle Identification Number (VIN):3FAHP0HG6AR. Ford Fusion 2010 problem was reported in CYPRESS, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10422684

FORD FUSION 2010 car safety problem was reported on Aug 30, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . the automatic transmission in my 2010 fusion se shifts erratically in the low gears. the vehicle is still under warranty so i took it to the ford stealership. i had pulled the transmission dipstick and noticed that the fluid was greyish black colored. they told me that the fluid was supposed to be that color. i asked them to get a brand new quart of the mercon lv fluid, and proved it was a dark red. i talked them in to replacing the transmission fluid for free. i swear the dealerships lie through their teeth to keep from doing anything for free under warranty. the vehicle still shifts funny; in the first two gears it feels like it slips even though it really isn't slipping. its just a choppy shift of gears. they said the way it shifts is normal, however, when i asked them to put that in writing and sign it, they wouldn't do it. the response was "it has a 60k mile power train warranty." way to change the subject! appears to me that ford and its crooked dealerships are quick to sell you a car, but slow to take care of you after the sale. (if they take care of you at all that is.) i think mike rowe should tell people this on the ford tv commercials. *tr.Mileage was 45000 miles. Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in JANESVILLE, WI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Power Train Review #10423241

FORD FUSION 2010 car safety problem was reported on Apr 14, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . we had a problem with a transmission leak early on due to a bad seal in the trans axle. it was replaced and all seemed well fro awhile. then we started to experience problems with the transmission "slipping" between 2nd and 3rd gears. took it to the dealership and they said it was a "computer problem" that need an update and that it should be ok now. it happened again at a later date. technician took it for a drive and then told my wife that there was nothing wrong, that is the way it's supposed to shift. at times it jerks really bad when shifting. not sure if the transmission problem can affect my fuel in-efficiency but, the car is far from the mileage advertised for this make. transmission problem is intermittent at this point. i'm afraid we are going to get pushed right through our warranty period, then that is when they will find the problem! we have insisted on a new transmission from the start, just to be stopped dead in our tracks with a flat refusal. hoping i can unload this car before something big happens. seems a shame that ford is the only automaker to keep it's head above water and not have to be bailed out. the sooner they admit they have a problem here and rectify it the better for everyone. if not, ford will join the others as a modern american failure! if you have any problem like this please post it right away! in the meantime, we are shopping for a nice solid japanese model. *tr.Mileage was 20923 miles. Vehicle Identification Number (VIN):3FAHP0HG2AR. Ford Fusion 2010 problem was reported in LOGANSPORT, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10423244

FORD FUSION 2010 car safety problem was reported on Sept 03, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . there was a recall on the 2010 ford fusion transmissions. i took the car in on 12/31/10 to automax ford, killeen, tx. they told me that nothing was wrong with it and it is fine. on 3 august 2011 my car felt like it did a downshift while going down the highway. at this point my accelerator fails to work. the car is not in any gear and even when i give the car gas the engine will not rev. i then have to come to a complete stop and put the car in park. while in park the car idles really heavy like and stuttters to keep going so i have to turn the car off. when i turn the car back on it will turn over about 6 or 7 times before it starts. i have to do this process every time the car does this which has been about 6 times in the past two days. the incident happens on the highway and in regular city driving. i believe automax ford has failed to do the inspection right and now the recall letter is expired as of april 2011. i was also deployed overseas during that time period of expiration. *tr.Mileage was 27000 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in FORT HOOD, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10423244

FORD FUSION 2010 car safety problem was reported on Sept 03, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . there was a recall on the 2010 ford fusion transmissions. i took the car in on 12/31/10 to automax ford, killeen, tx. they told me that nothing was wrong with it and it is fine. on 3 august 2011 my car felt like it did a downshift while going down the highway. at this point my accelerator fails to work. the car is not in any gear and even when i give the car gas the engine will not rev. i then have to come to a complete stop and put the car in park. while in park the car idles really heavy like and stuttters to keep going so i have to turn the car off. when i turn the car back on it will turn over about 6 or 7 times before it starts. i have to do this process every time the car does this which has been about 6 times in the past two days. the incident happens on the highway and in regular city driving. i believe automax ford has failed to do the inspection right and now the recall letter is expired as of april 2011. i was also deployed overseas during that time period of expiration. *tr.Mileage was 27000 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in FORT HOOD, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10423244

FORD FUSION 2010 car safety problem was reported on Sept 03, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . there was a recall on the 2010 ford fusion transmissions. i took the car in on 12/31/10 to automax ford, killeen, tx. they told me that nothing was wrong with it and it is fine. on 3 august 2011 my car felt like it did a downshift while going down the highway. at this point my accelerator fails to work. the car is not in any gear and even when i give the car gas the engine will not rev. i then have to come to a complete stop and put the car in park. while in park the car idles really heavy like and stuttters to keep going so i have to turn the car off. when i turn the car back on it will turn over about 6 or 7 times before it starts. i have to do this process every time the car does this which has been about 6 times in the past two days. the incident happens on the highway and in regular city driving. i believe automax ford has failed to do the inspection right and now the recall letter is expired as of april 2011. i was also deployed overseas during that time period of expiration. *tr.Mileage was 27000 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in FORT HOOD, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10424049

FORD FUSION 2010 car safety problem was reported on Aug 28, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact stated while driving approximately 45 mph with pressure applied to the accelerator pedal there was no power response and the rpms began to decrease. the contact coasted to the side of the road and turned the engine off. upon restarting the engine the vehicle operated normally. the failure recurred twelve times. the vehicle was taken to an authorized dealer where the throttle body was replaced. the manufacturer was made aware of the defect. the approximate failure mileage was 39,500. the vin was unavailable. .Mileage was 39500 miles. Ford Fusion 2010 problem was reported in EVANS, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10424191

FORD FUSION 2010 car safety problem was reported on Sept 04, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . i have a 2010 ford fusion and this is my second entry into this database for a broken stud. after ~21000 miles, a second stud on the front drivers wheel has failed by shearing completely. once again the dealer will only replace the broken stud, leaving me to worry over the remaining studs. also, it has taken two nights for the dealership to receive the new stud. *tr.Mileage was 21000 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in JOHNSON CITY, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10424195

FORD FUSION 2010 car safety problem was reported on Aug 08, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while driving on the highway, my 2010 ford fusion suddenly slipped gears on its own. the car started to slow down. i was stepping on the gas pedal, the engine was turning but the car wasn't accelerating. i was nearly rear ended. i managed to coast to the emergency lane. i put it in park and turned the car off. i was afraid to continue but thought i would give it a try. the car started ok and accelerated normally. the next week, my husband had the same experience. my husband took the car to ford dealership the next day. the dealership called and told us that they can't duplicate the transmission problem and their computer tests did not detect any problems. i told them of the numerous complaints i found online about this problem and that i didn't feel safe driving my car. they said they haven't heard of any complaints nor any tsbs on this car! i sent them a link to this website and told them to read it. will they still say nothing was wrong because their computers can't duplicate it? or do they think i like being without a vehicle and wasting everyone's time? *tr.Mileage was 13000 miles. Vehicle Identification Number (VIN):3FAHP0KC5AR. Ford Fusion 2010 problem was reported in NILES, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train Review #10424376

FORD FUSION 2010 car safety problem was reported on Sept 07, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . severe transmission slippage when trying to accelerate. engine rpm's increased rapidly but vehicle did not speed up. caused a near collision when trying to cut across several lanes of traffic. *tr.Mileage was 23500 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in RIVERVIEW, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 5 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10424382

FORD FUSION 2010 car safety problem was reported on Sept 16, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . while traveling in my new ford fusion approximately between 55 - 60 mph on the expressway, without any warning my car speed dropped instantly from 55-60 mph down to 5 mph, at the same time the wrench on the dashboard illuminated. unable to accelerate i immediately hit my hazards barely making it across two lanes to the shoulder and to safety, i turned the car off, and then back on, all seem well. thank god, the traffic was not heavy. i took the car to ford, after only one day in the shop i was informed, that they were unable to duplicate the problem and that it was hooked to and tested with the diagnostics machine. i was told that maybe it was just a glitch, or fluke, reluctant, i accepted my car back. but, needless to say exactly one week later it happened again, this time i was on the entrance ramp to a very crowded expressway, traveling approximately 30 mph, speed suddenly dropped to less than 5 mph, acceleration was not possible wrench light illuminated. next morning back in fords shop. after having my car for eight days and 40+ miles added to my ford fusion i was informed that the problem could not be duplicated. i contacted ford customer service and voiced my concern, one day later i was informed my car was ready and that the problem was identified, and the throttle had to be replaced. *tr.Vehicle Identification Number (VIN):3FAHP0JG0AR. Ford Fusion 2010 problem was reported in CHICAGO, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10424384

FORD FUSION 2010 car safety problem was reported on Aug 28, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while pulling into traffic, my ford fusion lost power, would not allow me to accelerate and started thrusting forward and jerking and the wrench warning light came on. i coasted to safety, put it into park, turned the car off and waited about 30 seconds, turned the car back on and the wrench light was gone and the car seemed fine. four days later, the same thing happened again. i took my car to a ford dealership, they told me they couldn't get any codes and had me come and get it. about two miles down the road, in middle of busy traffic, it happened again. i was lucky enough to get to safety, i called the dealership and they told me to drive it back. they still could not get it to duplicate the problem, there were no codes being thrown, so they told me to come and get the car. i told them about the numerous online complaints i found online about this problem and every time, it was a bad throttle body. he said they can't just replace the throttle body until they get the codes. he told me to drive it until it dies again, turn the car off but not back on and get it towed to them, then maybe they can get the codes. i am scared and feel unsafe driving it. looking at past times it died, it was while driving for a while, then shut off then ran shortly after. it seems to only be an issue with the 2010's, and always happens between 30-40 thousand miles, and it's always a bad throttle body. i can't even tell you how many complaints i read online and i personally know of two owners that had the same exact problem. obviously it is a design defect that needs to be recalled/repaired. i am scared and feel unsafe driving a car that i am just waiting on dying; i have never been placed in danger with a vehicle like this. no one should be required to drive in middle of busy traffic just waiting for it to die so they can try and get a code. *tr.Vehicle Identification Number (VIN):3FAHP0HGXAR. Ford Fusion 2010 problem was reported in COVINGTON, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Power Train Review #10424410

FORD FUSION 2010 car safety problem was reported on Apr 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . this is the 4 cylinder version of the 2010 fusion. since the car was only a few months old, the transmission has been slipping in low gear. as the mileage has gone up it has occurred more often but mainly in low gears. the problem has been that it does not set off any service lights so they had not been able to find anything to fix. after driving the car for about a year, it finally happened at high speed and turned on the service light. it was bad enough that i had to pull off the road. by this time, the transmission was damaged and they had to rebuild many of the parts. ford knew this was occurring and had a bulletin all about it. this shows that prior to the rebuild, ford already knew the transmission has had issues. prior to the rebuild, the transmission had been through multiple tests, a reprogramming of the transmission, and other changes to the transmission from their technical service bulletins. i did open a case with ford customer service. they admitted to me that the transmission has had issues in other cars and they are working on how to resolve them. soon after i was told that, i was assigned to a different customer service representative who denied this fact. after a few months more, i got a call from ford stating that they have no idea how to fix the problem so they are just closing the case with no resolution. i asked for a replacement transmission and they have said no. if you look in the forums for the 2010 ford fusion 4 cylinder, you will see how common the issue is. on top of all this, my gas mileage has dropped since the rebuild of the transmission. *tr.Mileage was 10000 miles. Vehicle Identification Number (VIN):3FAHP0JA5AR. Ford Fusion 2010 problem was reported in PHOENIXVILLE, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Power Train Review #10424524

FORD FUSION 2010 car safety problem was reported on Sept 07, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . car stop responding to accelerator,just coast along wrench symbol came on dash. picked up car today paid 200,17 for repair got 4 miles away from shop car stopped again. *tr.Mileage was 42000 miles. Vehicle Identification Number (VIN):3FAHPOHA6AR. Ford Fusion 2010 problem was reported in OLLIVETTE, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Power Train Review #10425113

FORD FUSION 2010 car safety problem was reported on May 17, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . when driving along, the rpms shot up to over 4500 with no increase in speed or increase in pressure on the accelerator pedal. the cruise control was also on at the time. *tr.Mileage was 7800 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in BELLEVUE, NE. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train Review #10425130

FORD FUSION 2010 car safety problem was reported on Sept 06, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . my car has went out 3 times in week twice on the freeway with oncoming traffic. it slows down then a wrench symbol comes on. i purchased my vehicle 3 weeks ago. took it back to the dealer and was told by the service dept that i need to have the throttle body repaired,. they ordered the part and said i need to pay $100 deductible. i just purchased this car i shouldn't have to pay anything if it would have been checked out correctly i wouldn't have had this problem. they also told me i need a new battery!! three weeks after i purchased it!! this should have been replaced by them for free, they said i would need to buy a new battery and it would be $109.00 more plus the deductible. i am very disappointed in this car. i love the way it looks but am so unsatisfied with the performance. if i get into an accident i hold ford co completely responsible for any damages, as i see they have had many complaints and they are not doing anything about it. i am looking into an attorney because this car should not be sold if it has this defect, it is putting peoples lives in danger!! what are they waiting for to see how many deaths will occur before they let people know not to buy it. i plan on telling everyone not to purchase i ford. i should have purchased a honda/like before. *tr.Mileage was 40052 miles. Vehicle Identification Number (VIN):3FAHP0HA4AR. Ford Fusion 2010 problem was reported in HOUSTON, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train Review #10425213

FORD FUSION 2010 car safety problem was reported on Sept 09, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . when i go to shift from 1st to 2nd, 2nd to 3rd, etc, it seems like the car is not registering the change in gears. as soon as i shift and attempt to continue accelerating, the engine will rev up too fast and then drop down and rev up normally. *tr whenever i attempt to use cruise control, going up a hill cause the engine to rev to quick again, shutting off cruise control. my car is 10 months old with just 23,000 miles (5700 of which were on it before i bought it) and the dealership i took it to is trying to tell me that it's normal wear and tear, and that the clutch and clutch plate need to be replaced. they're also saying it's not covered under warranty and that it will cost me $1300 + tax to repair. i don't drive this car hard, nor do i do any type of racing or mods to it. it's a car i use for work mainly. there is absolutely no reason the clutch should have to be replaced so soon. there are numerous sites with this same issue with similar fusions. point is, i'm not paying for this repair. *tr.Mileage was 23000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in OAK HARBOR, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Service Brakes, Hydraulic

Ford Fusion 2010 Service Brakes, Hydraulic Review #10426312

FORD FUSION 2010 car safety problem was reported on June 05, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC . tl* the contact owns a 2010 ford fusion. while driving approximately 65 mph on a mountainous road, the contact began to down shift and the brakes were applied numerous times before coming to a stop. the brakes emitted a strong burning odor. the vehicle was taken to an authorized dealer for a diagnostic test. the technician stated the brakes responded normally. the manufacturer was made aware of the defect. the approximate failure mileage was 17,000. the vin was unavailable. .Vehicle was on fire. Mileage was 17000 miles. Ford Fusion 2010 problem was reported in NEWPORT, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Traction Control System

Ford Fusion 2010 Traction Control System Review #10426437

FORD FUSION 2010 car safety problem was reported on Aug 12, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with TRACTION CONTROL SYSTEM . tl* the contact owns a 2010 ford fusion. the contact stated that while driving 55 mph, the check engine light would illuminate on the instrument panel and the vehicle would stop accelerating. in order to correct the failure, the contact would stop the vehicle and shut it off. upon restart, the vehicle would operate as normal. the vehicle was taken to an independent repair shop and the contact was informed that the traction control system needed to be repaired. the vehicle was repaired, but the failure continued. the manufacturer was made aware of the failure and offered no assistance. the failure mileage was 46,000. .Mileage was 46000 miles. Vehicle Identification Number (VIN):3FAHP0HG4AR. Ford Fusion 2010 problem was reported in SOUTHERLIN, OR. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10426666

FORD FUSION 2010 car safety problem was reported on Sept 20, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . while traveling 45 mph lost acceleration and coasted to side of the road. wrench or service light came on. shut car off and waited about 30 seconds and restarted car and service light went off and car operated normally. took the car to nearest dealer and they said they couldn't pull up any diagnostic codes and for me to wait for the problem to occur again and bring it back. car only has 37000 miles and after doing some research i have found multiple complaints about the very same issue with other fusion owners. all the cars that have been repaired had to replace the throttle body. *tr.Vehicle Identification Number (VIN):AE5J19G219Q. Ford Fusion 2010 problem was reported in GRIFFIN, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10426685

FORD FUSION 2010 car safety problem was reported on Feb 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i purchased a 2010 ford fusion with 24,000 miles in january 2011. i began having issues with transmission almost immediately. the transmission will frequently "slip" while taking off and shifts very hard at times. i will also "slip" when driving at higher road speeds causing the rpm's to rev but the car will not accelerate. recently, i was driving approximately 50 mph on a busy highway when the car stalled and the wrench light came on. the engine was running but the car would not accelerate. once i got pulled over, the rpm's bounced up and down rapidly. the car has been in the shop approximately 9 times so far. they replicated the issue once and transmission repairs were made but the issue continued. it is still under warranty but ford will not authorize any additional repairs since they haven't replicated the issue again. i just learned that this is a common issue with the ford fusion and that the 10b15 recall was performed on the vehicle just before i purchased it. after additional research, findings indicate that the recall has not corrected the issue in many cases. i do not feel safe when driving this vehicle and it is very disappointing to learn that ford will not take appropriate actions to provide reliable vehicles to their customers. *tr.Mileage was 26000 miles. Vehicle Identification Number (VIN):3FAHPOJGXAR. Ford Fusion 2010 problem was reported in PORTAGE DES SIOUX, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train Review #10426686

FORD FUSION 2010 car safety problem was reported on Aug 15, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while driving the transmission slipped and made the care downshift and upshift the car hard. i had to apply the brakes hard because the rpms where jumping as i cam to a complete stop. then when accelerating the car shifted hard. *tr.Mileage was 29000 miles. Vehicle Identification Number (VIN):3FAHP0HG2AR. Ford Fusion 2010 problem was reported in LEXINGTON, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Unknown Or Other

Ford Fusion 2010 Unknown Or Other Review #10426852

FORD FUSION 2010 car safety problem was reported on Aug 16, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with UNKNOWN OR OTHER . just starting off from a traffic light the car started to stall. the car was towed to montrose ford where they determined a part in the transmission failed. the part was ordered and replaced a few days later. on the 16th of september while driving the brakes failed. the car was taken to ganley ford on the 19th of sept. they initially determined it was a transmission problem, exactly the same problem that was repaired in august. on the 21st of sept. the maintenance people drove the car with a computer connected to analyze what was happening but found nothing wrong. now they say the problem is hydraulic related but will need to keep the car for at least 30 days to solve the problem. at this time they have no idea what is really wrong. inside the car is an intermittent noise. it can only be heard when just starting out or at very slow speeds. ganley ford has no idea where this noise is coming from. *tr.Mileage was 17000 miles. Vehicle Identification Number (VIN):3FAHP0HA4AR. Ford Fusion 2010 problem was reported in COPLEY, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10426852

FORD FUSION 2010 car safety problem was reported on Aug 16, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . just starting off from a traffic light the car started to stall. the car was towed to montrose ford where they determined a part in the transmission failed. the part was ordered and replaced a few days later. on the 16th of september while driving the brakes failed. the car was taken to ganley ford on the 19th of sept. they initially determined it was a transmission problem, exactly the same problem that was repaired in august. on the 21st of sept. the maintenance people drove the car with a computer connected to analyze what was happening but found nothing wrong. now they say the problem is hydraulic related but will need to keep the car for at least 30 days to solve the problem. at this time they have no idea what is really wrong. inside the car is an intermittent noise. it can only be heard when just starting out or at very slow speeds. ganley ford has no idea where this noise is coming from. *tr.Mileage was 17000 miles. Vehicle Identification Number (VIN):3FAHP0HA4AR. Ford Fusion 2010 problem was reported in COPLEY, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Service Brakes, Hydraulic

Ford Fusion 2010 Service Brakes, Hydraulic Review #10426852

FORD FUSION 2010 car safety problem was reported on Aug 16, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC . just starting off from a traffic light the car started to stall. the car was towed to montrose ford where they determined a part in the transmission failed. the part was ordered and replaced a few days later. on the 16th of september while driving the brakes failed. the car was taken to ganley ford on the 19th of sept. they initially determined it was a transmission problem, exactly the same problem that was repaired in august. on the 21st of sept. the maintenance people drove the car with a computer connected to analyze what was happening but found nothing wrong. now they say the problem is hydraulic related but will need to keep the car for at least 30 days to solve the problem. at this time they have no idea what is really wrong. inside the car is an intermittent noise. it can only be heard when just starting out or at very slow speeds. ganley ford has no idea where this noise is coming from. *tr.Mileage was 17000 miles. Vehicle Identification Number (VIN):3FAHP0HA4AR. Ford Fusion 2010 problem was reported in COPLEY, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10426879

FORD FUSION 2010 car safety problem was reported on Sept 22, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i previously sent a complaint because my car kept stalling, wrench light would come on, but when i turned car off then turned on, it would run, but then they couldn't get the codes. based on my internet research, looks like 2010 fusions are having this problem between 30,000 and 50,000 and it is always the throttle body that needs to be replaced. the dealership would not replace the throttle body because the codes were not coming up. i just wanted to give you an update, i purchased my own code reader and after my car died in the middle of the road (very dangerous) three more times, was finally able to get the code myself. i brought it to the dealership and with the code they were finally able to look it up.....and it was the throttle body....just like i told them since every 2010 ford fusion between this mileage is have the same problem. since this is obviously a defect on this car and is dangerous because car stalls in middle of traffic, it needs to be recalled! i don't want anyone to go through what i went through, and i would love to get reimbursed for the money i had to pay on fords defect. thank you *tr.Mileage was 51000 miles. Vehicle Identification Number (VIN):3FAHP0HGXAR. Ford Fusion 2010 problem was reported in COVINGTON, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Steering

Ford Fusion 2010 Steering Review #10427502

FORD FUSION 2010 car safety problem was reported on Sept 23, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with STEERING . power steering was in a parking lot. it could be steered by man power. took to ford garage and was the power steering rack. was advised it could have been very dangerous if it had happened on the highway at high speed and on curves which we had just done that day. *tr.Mileage was 12422 miles. Vehicle Identification Number (VIN):3FAHP0HA2AR. Ford Fusion 2010 problem was reported in BEAVERTON, OR. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10427644

FORD FUSION 2010 car safety problem was reported on Mar 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . tl* the contact owns a 2010 ford fusion. the contact was driving 35 mph when the vehicle stalled without warning. the failure was experienced numerous times. the engine emission and mechanical attention light illuminated after the failure occurred. the vehicle was towed to the dealer who performed a diagnostic that located the failure at the throttle body. the vehicle was not repaired. the manufacturer denied assistance with the repair. the failure mileage was 40,000 and the current mileage was 50,000. .Mileage was 40000 miles. Vehicle Identification Number (VIN):3FAHP0HG1AR. Ford Fusion 2010 problem was reported in IRVINE, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10427913

FORD FUSION 2010 car safety problem was reported on Sept 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . this problem is due to a faulty transmission or transmission components, as outlined by ford recall 10b15. the car jerks/slips and it feels as if the gears are not catching upon acceleration. i received the 'recall' letter from ford describing this program, and immediately brought the car to the dealership. they preformed the module recalibration and told me everything was fine. however, 40,000 later, my transmission started exhibiting the problems described above and ford is now replacing my entire transmission, although not paying for the rental car. *tt.Mileage was 56000 miles. Vehicle Identification Number (VIN):3FAHP0HA9AR. Ford Fusion 2010 problem was reported in IOWA FALLS, IA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS.

Ford Fusion 2010 Power Train Review #10427972

FORD FUSION 2010 car safety problem was reported on May 05, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . transmission still slipping from 2nd to 3rd gear after rebuild. this car is not safe. *tt.Mileage was 12000 miles. Vehicle Identification Number (VIN):3FAHP0HG8AR. Ford Fusion 2010 problem was reported in CHARLOTTE, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10428014

FORD FUSION 2010 car safety problem was reported on Sept 09, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . tl* the contact owns a 2010 ford fusion hybrid. the contact stated while having an oil change the mechanic noticed the front right axle nut had come loose. the contact spoke to the dealer who stated there was nothing they could do since the warranty had expired. the dealer installed a new axle nut. the contact stated that was a manufacturers defect that could cause the tire to disconnect from the vehicle and cause a crash. the failure mileage 37,571. updated 10/14/11 *bf updated 11/02/11 .0 person(s) were injured. 0 person(s) died.Mileage was 37571 miles. Vehicle Identification Number (VIN):3FADP0L32AR. Ford Fusion 2010 problem was reported in MADISON, WI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: HYBRID ELECTRIC. VEHICLE SPEED: 0 mph. DEALER'S NAME: CAPITOL FORD & KIA . DEALER'S TELEPHONE NUMBER: 608-246-3620 . DEALER'S CITY: MADISON . DEALER'S STATE CODE: WI. DEALER'S ZIPCODE: 53718 .

Ford Fusion 2010 Power Train Axle Hubs

Ford Fusion 2010 Power Train Axle Hubs Review #10428014

FORD FUSION 2010 car safety problem was reported on Sept 09, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AXLE HUBS . tl* the contact owns a 2010 ford fusion hybrid. the contact stated while having an oil change the mechanic noticed the front right axle nut had come loose. the contact spoke to the dealer who stated there was nothing they could do since the warranty had expired. the dealer installed a new axle nut. the contact stated that was a manufacturers defect that could cause the tire to disconnect from the vehicle and cause a crash. the failure mileage 37,571. updated 10/14/11 *bf updated 11/02/11 .0 person(s) were injured. 0 person(s) died.Mileage was 37571 miles. Vehicle Identification Number (VIN):3FADP0L32AR. Ford Fusion 2010 problem was reported in MADISON, WI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: HYBRID ELECTRIC. VEHICLE SPEED: 0 mph. DEALER'S NAME: CAPITOL FORD & KIA . DEALER'S TELEPHONE NUMBER: 608-246-3620 . DEALER'S CITY: MADISON . DEALER'S STATE CODE: WI. DEALER'S ZIPCODE: 53718 .

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10428153

FORD FUSION 2010 car safety problem was reported on Oct 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . on october 1, 2011, while pulling into a parking space, going less than a few miles an hour and applying the brake , the car suddenly lurched forward and accelerated on its on - jumped the curb and crashed through the window of a business. *tr.Vehicle was involved in a crash. Mileage was 44000 miles. Vehicle Identification Number (VIN):3FAHP0HAXAR. Ford Fusion 2010 problem was reported in ARLINGTON, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10429149

FORD FUSION 2010 car safety problem was reported on Apr 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . vehicle slips/hesitates when shifting from 1st to 2nd gear. transmission clutches were found 'burnt' and needed to be replaced. problem persists and now i am told this is 'normal' operation. in addition, my wheels are now vibrating/wobbling. i will need additional service. *tr.Mileage was 6000 miles. Ford Fusion 2010 problem was reported in HILLSBOROUGH, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10429149

FORD FUSION 2010 car safety problem was reported on Apr 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . vehicle slips/hesitates when shifting from 1st to 2nd gear. transmission clutches were found 'burnt' and needed to be replaced. problem persists and now i am told this is 'normal' operation. in addition, my wheels are now vibrating/wobbling. i will need additional service. *tr.Mileage was 6000 miles. Ford Fusion 2010 problem was reported in HILLSBOROUGH, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10429343

FORD FUSION 2010 car safety problem was reported on Apr 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . transmission slips and shifts hard in low gears. ford has replaced several transmission components but the problem still persists. i fear i may crash into the rear of another car when this occurs. recently a new problem has developed at high speeds where the transmission does not shift and runs at 4500 rpm for 20-30 seconds. ford says nothing is wrong despite me sending a video of the console when this happens. *kb.Ford Fusion 2010 problem was reported in ALEXANDRIA, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10429343

FORD FUSION 2010 car safety problem was reported on Apr 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . transmission slips and shifts hard in low gears. ford has replaced several transmission components but the problem still persists. i fear i may crash into the rear of another car when this occurs. recently a new problem has developed at high speeds where the transmission does not shift and runs at 4500 rpm for 20-30 seconds. ford says nothing is wrong despite me sending a video of the console when this happens. *kb.Ford Fusion 2010 problem was reported in ALEXANDRIA, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train Review #10429631

FORD FUSION 2010 car safety problem was reported on Oct 12, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while driving down the interstate in rush hour traffic, my 2010 fusion (35,265 mi) lost acceleration. jerked car into the median and put into park, it immediately began idling very rough and almost sputtering to cut off. the wrench light displayed. i cut the car off and let it sit for a moment and then cut the car back on. i pressed the gas and the cars rpm shot up to over 5000 rpm. it then idled normally and i merged back in traffic just hoping to get it to my office. i made it another 2-3 miles and it did it again, this time both the engine light and wrench lit up. i immediately cut it off, restarted it and it seemed fine. i decided to get off at the exit i was close too and park the car as i knew i was going to cause a major accident if i did not get it off the road. i came to the top of the exit ramp and sat in traffic for a few minutes, the car seemed okay, no rough idle nothing strange except the engine light was still displayed. i merged into traffic off the ramp and in the middle of the road same thing occurred, no acceleration, i had my foot to the floor. i got it into a parking lot and called the dealership. i had the car towed in got a loaner to drive into work. the ford dealership called about an hour later and said the car is fixed and i can come get it. they said their was an issue in my electronic throttle body and they have replaced the throttle body. i love this car but at 35,000 miles i should not have already had a bad battery and now this issue. i am starting to not trust the car. i hope the issue is fixed, but i am almost scared to go pick it up tonight. i had no idea of these issues until i looked it up online after the this morning. *kb.Mileage was 35265 miles. Ford Fusion 2010 problem was reported in CONCORD, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Power Train Automatic Transmission Review #10429631

FORD FUSION 2010 car safety problem was reported on Oct 12, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . while driving down the interstate in rush hour traffic, my 2010 fusion (35,265 mi) lost acceleration. jerked car into the median and put into park, it immediately began idling very rough and almost sputtering to cut off. the wrench light displayed. i cut the car off and let it sit for a moment and then cut the car back on. i pressed the gas and the cars rpm shot up to over 5000 rpm. it then idled normally and i merged back in traffic just hoping to get it to my office. i made it another 2-3 miles and it did it again, this time both the engine light and wrench lit up. i immediately cut it off, restarted it and it seemed fine. i decided to get off at the exit i was close too and park the car as i knew i was going to cause a major accident if i did not get it off the road. i came to the top of the exit ramp and sat in traffic for a few minutes, the car seemed okay, no rough idle nothing strange except the engine light was still displayed. i merged into traffic off the ramp and in the middle of the road same thing occurred, no acceleration, i had my foot to the floor. i got it into a parking lot and called the dealership. i had the car towed in got a loaner to drive into work. the ford dealership called about an hour later and said the car is fixed and i can come get it. they said their was an issue in my electronic throttle body and they have replaced the throttle body. i love this car but at 35,000 miles i should not have already had a bad battery and now this issue. i am starting to not trust the car. i hope the issue is fixed, but i am almost scared to go pick it up tonight. i had no idea of these issues until i looked it up online after the this morning. *kb.Mileage was 35265 miles. Ford Fusion 2010 problem was reported in CONCORD, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10429631

FORD FUSION 2010 car safety problem was reported on Oct 12, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . while driving down the interstate in rush hour traffic, my 2010 fusion (35,265 mi) lost acceleration. jerked car into the median and put into park, it immediately began idling very rough and almost sputtering to cut off. the wrench light displayed. i cut the car off and let it sit for a moment and then cut the car back on. i pressed the gas and the cars rpm shot up to over 5000 rpm. it then idled normally and i merged back in traffic just hoping to get it to my office. i made it another 2-3 miles and it did it again, this time both the engine light and wrench lit up. i immediately cut it off, restarted it and it seemed fine. i decided to get off at the exit i was close too and park the car as i knew i was going to cause a major accident if i did not get it off the road. i came to the top of the exit ramp and sat in traffic for a few minutes, the car seemed okay, no rough idle nothing strange except the engine light was still displayed. i merged into traffic off the ramp and in the middle of the road same thing occurred, no acceleration, i had my foot to the floor. i got it into a parking lot and called the dealership. i had the car towed in got a loaner to drive into work. the ford dealership called about an hour later and said the car is fixed and i can come get it. they said their was an issue in my electronic throttle body and they have replaced the throttle body. i love this car but at 35,000 miles i should not have already had a bad battery and now this issue. i am starting to not trust the car. i hope the issue is fixed, but i am almost scared to go pick it up tonight. i had no idea of these issues until i looked it up online after the this morning. *kb.Mileage was 35265 miles. Ford Fusion 2010 problem was reported in CONCORD, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10429631

FORD FUSION 2010 car safety problem was reported on Oct 12, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . while driving down the interstate in rush hour traffic, my 2010 fusion (35,265 mi) lost acceleration. jerked car into the median and put into park, it immediately began idling very rough and almost sputtering to cut off. the wrench light displayed. i cut the car off and let it sit for a moment and then cut the car back on. i pressed the gas and the cars rpm shot up to over 5000 rpm. it then idled normally and i merged back in traffic just hoping to get it to my office. i made it another 2-3 miles and it did it again, this time both the engine light and wrench lit up. i immediately cut it off, restarted it and it seemed fine. i decided to get off at the exit i was close too and park the car as i knew i was going to cause a major accident if i did not get it off the road. i came to the top of the exit ramp and sat in traffic for a few minutes, the car seemed okay, no rough idle nothing strange except the engine light was still displayed. i merged into traffic off the ramp and in the middle of the road same thing occurred, no acceleration, i had my foot to the floor. i got it into a parking lot and called the dealership. i had the car towed in got a loaner to drive into work. the ford dealership called about an hour later and said the car is fixed and i can come get it. they said their was an issue in my electronic throttle body and they have replaced the throttle body. i love this car but at 35,000 miles i should not have already had a bad battery and now this issue. i am starting to not trust the car. i hope the issue is fixed, but i am almost scared to go pick it up tonight. i had no idea of these issues until i looked it up online after the this morning. *kb.Mileage was 35265 miles. Ford Fusion 2010 problem was reported in CONCORD, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10430528

FORD FUSION 2010 car safety problem was reported on Sept 17, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while driving my 2010 ford fusion down a very busy main road in atlanta, it died. i was lucky that i was able to get over into the right hand lane without being able to accelerate and get onto a side street to park. the dealer replaced the throttle under warranty, but less than a month later i was getting on a busy freeway here in atlanta. about the same speed, 45mph, it wouldn't accelerate, but this time it did continue running. eventually it picked up again. it is currently back in the shop having the transmission corrected. ford did issue a recall last year which was supposed have corrected this issue, and i did take the car in for the recall when i had only had it for 30 days. that was over a year ago, and it has "skipped" between 2nd and 3rd gears the whole time which has made me uneasy, but eventually became the norm. anyway, the recall did not correct the issue. my fear is that when i am unable to accelerate, or when the car simply shuts down, i will be rear ended and cause a serious car accident involving others as well as myself. this is my first american brand car and i want to love it, but feeling unsafe driving it is making it difficult. i want this on file because although i have a warranty on my car, i think ford should be correcting the issue for all ford fusion owners since our safety is at risk. *tr.Ford Fusion 2010 problem was reported in ATLANTA, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train Review #10430581

FORD FUSION 2010 car safety problem was reported on Oct 05, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . my 2010 ford fusion has had issues for the last month with the lack of accelerating with the check engine light and the wrench light coming on. took it to advanced auto with a code of p2112. took it twice to the ford dealership with the first time the dealer telling me nothing. this happened again while i was driving through an intersection with my two kids in the car and lost almost all power and was nearly hit by an 18 wheeler. dealer said that the throttle body needs to be replaced, will cost me $520 dollars and it isn't covered under my power train warranty. thousands of reported problems with this very same problem with ford not being held responsible for faulty equipment...something needs to be done before someone is hurt or killed. *tr.Mileage was 40001 miles. Ford Fusion 2010 problem was reported in NAVARRE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10430680

FORD FUSION 2010 car safety problem was reported on Sept 10, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact was driving 45 mph when the vehicle decelerated and the throttle mission control failure switch illuminated. the failure recurred fifteen times. the vehicle was taken to the dealer where they confirmed that the throttle body needed to be replaced. the manufacturer was not contacted and the vehicle was not repaired. the failure mileage was 62,800 and the current mileage was 62,882. .Mileage was 62800 miles. Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in WILMINGTON, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10432393

FORD FUSION 2010 car safety problem was reported on July 15, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . this is related to nhtsa action number ea11009. so far i have had 2 incidents of broken wheel studs on a 2010 for fusion that was bought on 9/11/2010. the first occurred on 7/15/2011 at 25000 miles and the second occurrence was on 10/21/2011 at 33000 miles. both on driver side front wheel. the dealer has done all work to car so far. *tr.Mileage was 25000 miles. Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in WEARE, NH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Exterior Lighting

Ford Fusion 2010 Exterior Lighting Review #10432440

FORD FUSION 2010 car safety problem was reported on Oct 20, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with EXTERIOR LIGHTING . while driving on interstate i-81 the dash lights started going completely off and staying off for quite sometime before coming back on. i was not really sure if i had headlights until later when stopping behind someone on my destination and was able to see my headlights in their rear car. the weather was horrible, raining very hard and visibility was really only a few feet away. i turn on my fog lights just in case i had no headlights. i had hoped they work but i did not get out in the pouring rain to check. fortunately, this incident was during the daytime and not at night. this could have lead to a fatal accident if it was at night. i feel that others should be aware of this problem and ford should take care of it with no cost to owner. also the spots on the charcoal dash should be dealt with by ford because there is some reason other than sunlight or cleaner that has cause this, for i have only clean dash with a damp cloth and the car has been garage kept except for the time it spent on the dealership lot. there are many complaints on the charcoal dash on the ford fusion online. the dealership service department was very rude when i ask about this problem and seem to care less about their customers on this behalf and accuse me of using some type of harse cleaner on it...would not even listen to what i had to say. lets hope that ford stays behind their customers with problems on the fusion since it does have some problems. *tr.Mileage was 8000 miles. Vehicle Identification Number (VIN):3FAHP0JA5AR. Ford Fusion 2010 problem was reported in DANDRIDGE, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10432440

FORD FUSION 2010 car safety problem was reported on Oct 20, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . while driving on interstate i-81 the dash lights started going completely off and staying off for quite sometime before coming back on. i was not really sure if i had headlights until later when stopping behind someone on my destination and was able to see my headlights in their rear car. the weather was horrible, raining very hard and visibility was really only a few feet away. i turn on my fog lights just in case i had no headlights. i had hoped they work but i did not get out in the pouring rain to check. fortunately, this incident was during the daytime and not at night. this could have lead to a fatal accident if it was at night. i feel that others should be aware of this problem and ford should take care of it with no cost to owner. also the spots on the charcoal dash should be dealt with by ford because there is some reason other than sunlight or cleaner that has cause this, for i have only clean dash with a damp cloth and the car has been garage kept except for the time it spent on the dealership lot. there are many complaints on the charcoal dash on the ford fusion online. the dealership service department was very rude when i ask about this problem and seem to care less about their customers on this behalf and accuse me of using some type of harse cleaner on it...would not even listen to what i had to say. lets hope that ford stays behind their customers with problems on the fusion since it does have some problems. *tr.Mileage was 8000 miles. Vehicle Identification Number (VIN):3FAHP0JA5AR. Ford Fusion 2010 problem was reported in DANDRIDGE, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10432795

FORD FUSION 2010 car safety problem was reported on Oct 14, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . when i was driving my 2010 ford fusion the wrench light came on and the car lost all power and stalled out. luckily i wasn't in front of a truck or on the freeway. very scary my car only has 15391 miles on it. this car was also leaking oil. i am not happy with this car. when i took it to the dealer this problem didn't show up at first so the service person kept the car longer and finally it did the same thing and lost all power so they replaced the throttle body and replaced the the gasket that was leaking oil. also a few months earlier one of the coils went bad and had to be replaced. *tt .Mileage was 15391 miles. Vehicle Identification Number (VIN):3FAHP0JG8AR. Ford Fusion 2010 problem was reported in SANTA MONICA, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Fuel System, Gasoline

Ford Fusion 2010 Fuel System, Gasoline Review #10432795

FORD FUSION 2010 car safety problem was reported on Oct 14, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE . when i was driving my 2010 ford fusion the wrench light came on and the car lost all power and stalled out. luckily i wasn't in front of a truck or on the freeway. very scary my car only has 15391 miles on it. this car was also leaking oil. i am not happy with this car. when i took it to the dealer this problem didn't show up at first so the service person kept the car longer and finally it did the same thing and lost all power so they replaced the throttle body and replaced the the gasket that was leaking oil. also a few months earlier one of the coils went bad and had to be replaced. *tt .Mileage was 15391 miles. Vehicle Identification Number (VIN):3FAHP0JG8AR. Ford Fusion 2010 problem was reported in SANTA MONICA, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10432795

FORD FUSION 2010 car safety problem was reported on Oct 14, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . when i was driving my 2010 ford fusion the wrench light came on and the car lost all power and stalled out. luckily i wasn't in front of a truck or on the freeway. very scary my car only has 15391 miles on it. this car was also leaking oil. i am not happy with this car. when i took it to the dealer this problem didn't show up at first so the service person kept the car longer and finally it did the same thing and lost all power so they replaced the throttle body and replaced the the gasket that was leaking oil. also a few months earlier one of the coils went bad and had to be replaced. *tt .Mileage was 15391 miles. Vehicle Identification Number (VIN):3FAHP0JG8AR. Ford Fusion 2010 problem was reported in SANTA MONICA, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Power Train Review #10434010

FORD FUSION 2010 car safety problem was reported on Nov 02, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i was stopped at a traffic light, it turned green and stepped on the gas pedal and the car immediately started to rough idle, the wrench indicator lit up and would not move forward. there was minimal response to throttle input. i was able to pull off the road out of traffic to a safe spot. i left the car running to see what was going on. the tachometer was fluctuating mainly downward as it idled rough. after about two minutes i turned off the motor. i made a few phone calls and while calling roadside assist decided to try and start the car. it started and i went straight to the dealership. as fate would have it, the dealership could not duplicate the concern and was not able to pinpoint the cause. they were kind enough to suggest replacing the throttle body and motor assembly. it cost me $512.38. needlessto say i am not at all happy with this issue. this issue could have occurred in a more dynamic setting, heavy traffic, lane change or merging, etc, potentially causing threat to my life and that of others. this issue needs to be addressed by the manufacturer in my opinion. *tr.Mileage was 53425 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in BOYNTON BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10434010

FORD FUSION 2010 car safety problem was reported on Nov 02, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . i was stopped at a traffic light, it turned green and stepped on the gas pedal and the car immediately started to rough idle, the wrench indicator lit up and would not move forward. there was minimal response to throttle input. i was able to pull off the road out of traffic to a safe spot. i left the car running to see what was going on. the tachometer was fluctuating mainly downward as it idled rough. after about two minutes i turned off the motor. i made a few phone calls and while calling roadside assist decided to try and start the car. it started and i went straight to the dealership. as fate would have it, the dealership could not duplicate the concern and was not able to pinpoint the cause. they were kind enough to suggest replacing the throttle body and motor assembly. it cost me $512.38. needlessto say i am not at all happy with this issue. this issue could have occurred in a more dynamic setting, heavy traffic, lane change or merging, etc, potentially causing threat to my life and that of others. this issue needs to be addressed by the manufacturer in my opinion. *tr.Mileage was 53425 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in BOYNTON BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10434010

FORD FUSION 2010 car safety problem was reported on Nov 02, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . i was stopped at a traffic light, it turned green and stepped on the gas pedal and the car immediately started to rough idle, the wrench indicator lit up and would not move forward. there was minimal response to throttle input. i was able to pull off the road out of traffic to a safe spot. i left the car running to see what was going on. the tachometer was fluctuating mainly downward as it idled rough. after about two minutes i turned off the motor. i made a few phone calls and while calling roadside assist decided to try and start the car. it started and i went straight to the dealership. as fate would have it, the dealership could not duplicate the concern and was not able to pinpoint the cause. they were kind enough to suggest replacing the throttle body and motor assembly. it cost me $512.38. needlessto say i am not at all happy with this issue. this issue could have occurred in a more dynamic setting, heavy traffic, lane change or merging, etc, potentially causing threat to my life and that of others. this issue needs to be addressed by the manufacturer in my opinion. *tr.Mileage was 53425 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in BOYNTON BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10434114

FORD FUSION 2010 car safety problem was reported on Oct 20, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . tl* the contact owns a 2010 ford fusion. the contact stated that while driving, the wrench warning light illuminated on the instrument panel and the vehicle was resistant to shifting gears. a local mechanic diagnosed that there was a throttle body defect. neither the dealer nor the manufacturer was notified of the failure. the vehicle was repaired. the failure and the current mileage was 54,500..Mileage was 54500 miles. Vehicle Identification Number (VIN):3FAHP0CGXAR. Ford Fusion 2010 problem was reported in LAKESIDE PARK, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10434188

FORD FUSION 2010 car safety problem was reported on Oct 20, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . on three seperate incidents, i found wheel lugs missing from my right front wheel. ford shipped parts to my dealer 3 times and the vehicle was repaired. this last time (4th) i had just gotten off the hwy and turned into the parking lot at work when the front right wheel came off and rolled across the parking lot. the dealer est is over $3k in damage to repair the vehicle. even though this is the 4th time on the same wheel, ford has decided to fix this vehicle again. i do not believe this vehicle should even be on the road any more. two minutes earlier and the wheel would have came off at high speeds. there is definitely a danger to me, my passangers and any other people in the area when the wheel decides to leave the vehicle. *tr.Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in LODI, WI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10434989

FORD FUSION 2010 car safety problem was reported on Oct 18, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i own a v6 2010 ford fusion and on two separate occasions, while driving on the highway at approximate speeds of 65 mph the engine has stalled without warming. at the time the engine stalls, a service light will come on and the car completely shuts down. in both instances, the car could be restarted, and the service light disappeared upon restart. we have taken it to the dealership after both incidents, and they are unable to identify a fix as the service code is not being stored in events of engine failure (and the light is not staying on after restart). this is an extremely dangerous situation as it has happened without warning, while traveling on major highways at high speeds. i have seen entries from other owners on both the nhtsa site and other blogs sitting the same problem, yet ford is unwilling to accept that this is a pervasive problem and is not working to find a solution. we have escalated from the dealership up to the corporate ford customer service department with no success. *tr.Mileage was 24500 miles. Ford Fusion 2010 problem was reported in BRAINTREE, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10434989

FORD FUSION 2010 car safety problem was reported on Oct 18, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . i own a v6 2010 ford fusion and on two separate occasions, while driving on the highway at approximate speeds of 65 mph the engine has stalled without warming. at the time the engine stalls, a service light will come on and the car completely shuts down. in both instances, the car could be restarted, and the service light disappeared upon restart. we have taken it to the dealership after both incidents, and they are unable to identify a fix as the service code is not being stored in events of engine failure (and the light is not staying on after restart). this is an extremely dangerous situation as it has happened without warning, while traveling on major highways at high speeds. i have seen entries from other owners on both the nhtsa site and other blogs sitting the same problem, yet ford is unwilling to accept that this is a pervasive problem and is not working to find a solution. we have escalated from the dealership up to the corporate ford customer service department with no success. *tr.Mileage was 24500 miles. Ford Fusion 2010 problem was reported in BRAINTREE, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10435106

FORD FUSION 2010 car safety problem was reported on Nov 07, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . this is related to nhtsa action number ea11009. we discovered three broken wheel studs on our 2010 ford fusion, two on the front passenger wheel and one on the front drivers side wheel. all three had sheared off completely. the dealership argued the studs had sheared due to faulty maintenance work. the car has had maintenance only at ford dealerships. the dealership will only replace the broken studs and ignores our concern that the remaining studs may have been compromised. *tr.Mileage was 21900 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in SPRINGFIELD, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10435494

FORD FUSION 2010 car safety problem was reported on Oct 03, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . when car is driven for the first time or car has had a few hours to cool off the transmission hesitates to shift from 2-3 and 3-4. usually seams to slip from 3-4. *tr.Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in CLEARWATER, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10435720

FORD FUSION 2010 car safety problem was reported on Oct 11, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . tl* the contact owns a 2010 ford fusion. the contact was driving 40 mph when the vehicle stalled without warning. the contact was able to restart the vehicle. the vehicle was taken to the dealer but the dealer was unable to diagnose the problem. the contact stated that the stalling recurred twice afterward. the contact took the vehicle back to the dealer and after a second diagnostic test the dealer advised the contact that a cylinder was misfiring. the dealer replaced the coil wire to the cylinder but the failure recurred after repairs. the dealer was unable to locate any further problems with the vehicle. there were no further repairs. the failure mileage was 31,586. .0 person(s) were injured. 0 person(s) died.Mileage was 31586 miles. Vehicle Identification Number (VIN):3FAHP0HA2AR. Ford Fusion 2010 problem was reported in BATON ROUGE, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10436471

FORD FUSION 2010 car safety problem was reported on Oct 25, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . the front drivers side wheel lug has snapped off. *tr.Mileage was 25000 miles. Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in MENLO, IA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10437226

FORD FUSION 2010 car safety problem was reported on Nov 24, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while driving on the interstate on cruise control at 70 mph, the car lost acceleration/power, the wrench light came on and we had to coast to the shoulder of the interstate. came to a stop, and the car idled, but appeared to want to die. car was shutoff and restarted. wrench light went off. we continued on our way without further problems. this is the second time this has happened within a two months. brought the car to the lander's ford dealership in collierville, tn after the first time it happened, but was told they could not duplicate the problem. nothing was done. based on previous reports, this is a common issue and is related to throttle body defect. as noted by others, this power failure is a safety concern and could lead to a serious incident. *tr.Mileage was 30256 miles. Ford Fusion 2010 problem was reported in COLLIERVILLE, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10437318

FORD FUSION 2010 car safety problem was reported on Nov 03, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . i was pulling out from a red light when the car lost power and started to idle hard. i was able to pull to the turn lane to avoid being hit. when all power was lost and the car died the wrench light and battery light came on. the car did not seem to be getting any gas. after turning the car off and sitting a few minutes the car started back and i was able to pull to a parking lot. fortunately i was not on the interstate as i had been previously before this. my husband followed me to the dealership and after inspecting the car i was told it was the throttle body. the cost of the repair was $465.00 which i just considered one of those things that happens until i discovered there have been many similar complaints. four days later the car did the same thing on the highway. my husband was able to get off to the side of the road. the dealership checked it the next day and stated all the wiring. i will say the service department told us they were on the phone with ford that day and found no additional problems, but did state that if this problem happened again the computer system would be replaced. of course my biggest concern is if and when might this happen again, hopefully not on the interstate. i have enjoyed my fusion but ford should take some responsiblilty for this before a deadly situtaion happens. *tr.Vehicle Identification Number (VIN):3FAHPOGAXAR. Ford Fusion 2010 problem was reported in MAYNARDVILLE, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Structure Body

Ford Fusion 2010 Structure Body Review #10437462

FORD FUSION 2010 car safety problem was reported on Aug 28, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE:BODY . tl* the contact owns a 2010 ford fusion. the contact stated that while driving approximately 40 mph, the hood flew upwards and obscured the field of vision. the contact maneuvered the vehicle to the shoulder and closed the hood. the vehicle was not inspected by a dealer nor repaired. the manufacturer was notified and offered no assistance. the failure and current mileages were approximately 26,500. .Mileage was 26500 miles. Vehicle Identification Number (VIN):3FADP0L33AR. Ford Fusion 2010 problem was reported in 5151 EDWARD JAMES DRIVE, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10437765

FORD FUSION 2010 car safety problem was reported on Sept 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . transmission keeps on lurching forward and dealership cannot do anything about it now. it's a safety issue for me as i almost got into an accident on the street due to huge jump. transmission keeps on acting up and dealer keeps saying everything is fine and cannot duplicate the other since the time they rebuilt the transmission on my vehicle. *tr *kb.Mileage was 701 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in ROCHESTER HILLS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10437765

FORD FUSION 2010 car safety problem was reported on Sept 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . transmission keeps on lurching forward and dealership cannot do anything about it now. it's a safety issue for me as i almost got into an accident on the street due to huge jump. transmission keeps on acting up and dealer keeps saying everything is fine and cannot duplicate the other since the time they rebuilt the transmission on my vehicle. *tr *kb.Mileage was 701 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in ROCHESTER HILLS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10437765

FORD FUSION 2010 car safety problem was reported on Sept 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . transmission keeps on lurching forward and dealership cannot do anything about it now. it's a safety issue for me as i almost got into an accident on the street due to huge jump. transmission keeps on acting up and dealer keeps saying everything is fine and cannot duplicate the other since the time they rebuilt the transmission on my vehicle. *tr *kb.Mileage was 701 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in ROCHESTER HILLS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10437797

FORD FUSION 2010 car safety problem was reported on Nov 02, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . when driving the vehicle the throttle body fails putting the car into "limp mode". acceleration is impossible and the car will stall while attempting to safely pull off the road. after a single search online for "ford fusion throttle body" numerous instances of similar failures appear beginning in approximately 2005. the vehicle will lose all ability to accelerate but maintain electrical power until the vehicle stalls. this occurred to me while traveling on the highway at 75 mph and is extremely unsafe. the problem is so widespread that the local ford dealers maintain a stock of throttle body units to replace. the risk of an accident very high because of the possibility of stalling out and losing control of the vehicle. *kb.Mileage was 46000 miles. Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 75 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10437797

FORD FUSION 2010 car safety problem was reported on Nov 02, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . when driving the vehicle the throttle body fails putting the car into "limp mode". acceleration is impossible and the car will stall while attempting to safely pull off the road. after a single search online for "ford fusion throttle body" numerous instances of similar failures appear beginning in approximately 2005. the vehicle will lose all ability to accelerate but maintain electrical power until the vehicle stalls. this occurred to me while traveling on the highway at 75 mph and is extremely unsafe. the problem is so widespread that the local ford dealers maintain a stock of throttle body units to replace. the risk of an accident very high because of the possibility of stalling out and losing control of the vehicle. *kb.Mileage was 46000 miles. Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 75 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10437797

FORD FUSION 2010 car safety problem was reported on Nov 02, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . when driving the vehicle the throttle body fails putting the car into "limp mode". acceleration is impossible and the car will stall while attempting to safely pull off the road. after a single search online for "ford fusion throttle body" numerous instances of similar failures appear beginning in approximately 2005. the vehicle will lose all ability to accelerate but maintain electrical power until the vehicle stalls. this occurred to me while traveling on the highway at 75 mph and is extremely unsafe. the problem is so widespread that the local ford dealers maintain a stock of throttle body units to replace. the risk of an accident very high because of the possibility of stalling out and losing control of the vehicle. *kb.Mileage was 46000 miles. Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 75 mph.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10437837

FORD FUSION 2010 car safety problem was reported on Nov 23, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . i went to rotate the tires on my 2010 fusion and i noticed on the front left that a wheel lug stud had sheared right into, always had a dealership rotate my tires. i noticed this when i was rotating my tires and the rest of the lug stud is inside my lug nut. i have contacted my local dealership and they claim they know of no incidents and does not know if ford will cover it. i think after 280 reported incidents this should be a recall, i find it hard to believe in something like this being so dangerous that it is not already. i can say this with certainty, that after the first reported accident caused by this and the lawsuit that follows, someone will take notice. *kb.Mileage was 44384 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in BRYANT, AR. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Wheels Lugs/nuts/bolts

Ford Fusion 2010 Wheels Lugs/nuts/bolts Review #10437837

FORD FUSION 2010 car safety problem was reported on Nov 23, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS:LUGS/NUTS/BOLTS . i went to rotate the tires on my 2010 fusion and i noticed on the front left that a wheel lug stud had sheared right into, always had a dealership rotate my tires. i noticed this when i was rotating my tires and the rest of the lug stud is inside my lug nut. i have contacted my local dealership and they claim they know of no incidents and does not know if ford will cover it. i think after 280 reported incidents this should be a recall, i find it hard to believe in something like this being so dangerous that it is not already. i can say this with certainty, that after the first reported accident caused by this and the lawsuit that follows, someone will take notice. *kb.Mileage was 44384 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in BRYANT, AR. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10438114

FORD FUSION 2010 car safety problem was reported on Dec 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . while driving down a major highway at 69 mph with the cruise control on, the car just lost power. i first noticed the headlights went out, then saw the anti theft light illuminate. i tried depressing the gas pedal, but got nothing. thankfully, i was able to coast out of the passing lane, into the right lane, and eventually to the side of the road without any tragedy. once along the roadside, i put the car in park and turned the key to shut off mode. i then turned it back on, car started up fine. i took it to my regular mechanic, his code reader found nothing. took it to the dealership i bought it from, they found nothing. it is now at a ford dealership, but my guess is they will find nothing. i am on the road at least 4 out of 5 days a week on major highways. i cannot afford for this to happen again. i may not be so lucky next time. *tr.Mileage was 31118 miles. Vehicle Identification Number (VIN):3FAHPOKC9AR. Ford Fusion 2010 problem was reported in WIND GAP, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 69 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10438114

FORD FUSION 2010 car safety problem was reported on Dec 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . while driving down a major highway at 69 mph with the cruise control on, the car just lost power. i first noticed the headlights went out, then saw the anti theft light illuminate. i tried depressing the gas pedal, but got nothing. thankfully, i was able to coast out of the passing lane, into the right lane, and eventually to the side of the road without any tragedy. once along the roadside, i put the car in park and turned the key to shut off mode. i then turned it back on, car started up fine. i took it to my regular mechanic, his code reader found nothing. took it to the dealership i bought it from, they found nothing. it is now at a ford dealership, but my guess is they will find nothing. i am on the road at least 4 out of 5 days a week on major highways. i cannot afford for this to happen again. i may not be so lucky next time. *tr.Mileage was 31118 miles. Vehicle Identification Number (VIN):3FAHPOKC9AR. Ford Fusion 2010 problem was reported in WIND GAP, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 69 mph.

Ford Fusion 2010 Electrical System Review #10438138

FORD FUSION 2010 car safety problem was reported on Dec 02, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . tl* the contact owns a 2010 ford fusion hybrid. the contact stated that during routine maintenance, the dealer advised that the high voltage cable for the hybrid generator and battery was worn down to bare metal. the manufacturer was contacted but the vehicle was not repaired. the vin was unavailable. the failure and the current mileage was 36,453. .0 person(s) were injured. 0 person(s) died.Mileage was 36453 miles. Ford Fusion 2010 problem was reported in NORTH BEND, WA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Fuel System, Gasoline

Ford Fusion 2010 Fuel System, Gasoline Review #10438561

FORD FUSION 2010 car safety problem was reported on Nov 30, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE . the vehicle lost power, the gas pedal had no effect, and it would surge forward by itself. created a very scary and unsafe situation for my wife. i went to the gas station where she had managed to get pulled into and shut it off, i looked it over and restarted it. it seemed to have power and throttle response, so i attempted to drive it on home since it was within a mile. it again failed on me within 100 yards but i was able to limp it on home. the dealership towed it into service and they thought the throttle body was bad...so they replaced it and now it is working. they said this is happening to a lot of throttle bodies! i am not sure why there isn't a recall or more investigations happening here. this was totally unexpected from a vehicle with only 11k miles on it. *tr.Mileage was 11200 miles. Ford Fusion 2010 problem was reported in JACKSONVILLE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10438561

FORD FUSION 2010 car safety problem was reported on Nov 30, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . the vehicle lost power, the gas pedal had no effect, and it would surge forward by itself. created a very scary and unsafe situation for my wife. i went to the gas station where she had managed to get pulled into and shut it off, i looked it over and restarted it. it seemed to have power and throttle response, so i attempted to drive it on home since it was within a mile. it again failed on me within 100 yards but i was able to limp it on home. the dealership towed it into service and they thought the throttle body was bad...so they replaced it and now it is working. they said this is happening to a lot of throttle bodies! i am not sure why there isn't a recall or more investigations happening here. this was totally unexpected from a vehicle with only 11k miles on it. *tr.Mileage was 11200 miles. Ford Fusion 2010 problem was reported in JACKSONVILLE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Electronic Stability Control

Ford Fusion 2010 Electronic Stability Control Review #10439513

FORD FUSION 2010 car safety problem was reported on Dec 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRONIC STABILITY CONTROL . bought my fusion in april 2011. began having problems immediately. usually happens when the engine is cold, upon accelerating the car would lurch terribly and hesitate. first the dealer could find nothing wrong. then they decided it was the transmission. put new transmission in. kept happening. finally, it happened when the service manager drove it. said ford would put new computer in the car. six weeks later since we heard nothing back, took the car to the sales rep and he said don't come get it until we fix it. today my husband is back at the dealer to get me another car. they act like i am imagining all this. i am ready for an arbitrator!.Vehicle Identification Number (VIN):3FAHP0HG6AR. Ford Fusion 2010 problem was reported in MILLBROOK, AL. Vehicle was purchased on Apr 01, 2011. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10439513

FORD FUSION 2010 car safety problem was reported on Dec 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . bought my fusion in april 2011. began having problems immediately. usually happens when the engine is cold, upon accelerating the car would lurch terribly and hesitate. first the dealer could find nothing wrong. then they decided it was the transmission. put new transmission in. kept happening. finally, it happened when the service manager drove it. said ford would put new computer in the car. six weeks later since we heard nothing back, took the car to the sales rep and he said don't come get it until we fix it. today my husband is back at the dealer to get me another car. they act like i am imagining all this. i am ready for an arbitrator!.Vehicle Identification Number (VIN):3FAHP0HG6AR. Ford Fusion 2010 problem was reported in MILLBROOK, AL. Vehicle was purchased on Apr 01, 2011. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10439513

FORD FUSION 2010 car safety problem was reported on Dec 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . bought my fusion in april 2011. began having problems immediately. usually happens when the engine is cold, upon accelerating the car would lurch terribly and hesitate. first the dealer could find nothing wrong. then they decided it was the transmission. put new transmission in. kept happening. finally, it happened when the service manager drove it. said ford would put new computer in the car. six weeks later since we heard nothing back, took the car to the sales rep and he said don't come get it until we fix it. today my husband is back at the dealer to get me another car. they act like i am imagining all this. i am ready for an arbitrator!.Vehicle Identification Number (VIN):3FAHP0HG6AR. Ford Fusion 2010 problem was reported in MILLBROOK, AL. Vehicle was purchased on Apr 01, 2011. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10438725

FORD FUSION 2010 car safety problem was reported on Sept 28, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . yesterday (4dec2011) i was rotating my tires when one of the left front wheel studs on my 2010 ford fusion broke off inside of the lug nut. it was obviously weak for a while and finally broke when pressure was applied from the tire iron. my current mileage is approximately 48000. this follows a similar incident that occurred on 28sep2010 where one of the right front wheel studs broke off at approximately 13,500 miles. 2 of these fractures in less than 2 years is unacceptable. there is no sign of rust/wear or tear on any of the studs. i also noticed today that the ntsb is already looking into similar incidents through an engineering analysis. the potential for danger of a wheel flying off a car at a high rate of speed is quite high and a recall should be announced. *tr.Mileage was 13500 miles. Vehicle Identification Number (VIN):3FAHP0HG4AR. Ford Fusion 2010 problem was reported in MECHANVICSVILLE, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Structure Body Door

Ford Fusion 2010 Structure Body Door Review #10439118

FORD FUSION 2010 car safety problem was reported on Dec 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE:BODY:DOOR . tl* the contact owns a 2010 ford fusion. while driving approximately 55 mph, the vehicle decelerated abnormally. the contact stopped the vehicle and shifted into park as the vehicle began to shake vigorously and stalled. the vehicle was taken to the dealer for diagnostics and stalled a second time on while in route. the technician was unable to diagnose the failure because the computer was not providing a failure code. the failure recurred three times. the third time, the vehicle was towed to the dealer and the technician advised that the computer was not reading a failure code but the electronic throttle body would likely have to be replaced. the vehicle was not repaired. the approximate failure mileage was 43,000. updated 03/02/12*lj the consumer stated the rear window, weather stripping on the doors, and door handles had to be replaced. the consumer stated there have been numerous problems with the transmission. updated 03/08/12.Mileage was 43000 miles. Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in SAN ANTONIO, TX. Original Owner. Vehicle was purchased on Nov 01, 2009. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 55 mph. DEALER'S NAME: RED MCCOMBS . DEALER'S TELEPHONE NUMBER: 210-357-1437 . DEALER'S CITY: SAN ANTONIO . DEALER'S STATE CODE: TX.

Ford Fusion 2010 Visibility Glass, Side/rear

Ford Fusion 2010 Visibility Glass, Side/rear Review #10439118

FORD FUSION 2010 car safety problem was reported on Dec 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:GLASS, SIDE/REAR . tl* the contact owns a 2010 ford fusion. while driving approximately 55 mph, the vehicle decelerated abnormally. the contact stopped the vehicle and shifted into park as the vehicle began to shake vigorously and stalled. the vehicle was taken to the dealer for diagnostics and stalled a second time on while in route. the technician was unable to diagnose the failure because the computer was not providing a failure code. the failure recurred three times. the third time, the vehicle was towed to the dealer and the technician advised that the computer was not reading a failure code but the electronic throttle body would likely have to be replaced. the vehicle was not repaired. the approximate failure mileage was 43,000. updated 03/02/12*lj the consumer stated the rear window, weather stripping on the doors, and door handles had to be replaced. the consumer stated there have been numerous problems with the transmission. updated 03/08/12.Mileage was 43000 miles. Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in SAN ANTONIO, TX. Original Owner. Vehicle was purchased on Nov 01, 2009. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 55 mph. DEALER'S NAME: RED MCCOMBS . DEALER'S TELEPHONE NUMBER: 210-357-1437 . DEALER'S CITY: SAN ANTONIO . DEALER'S STATE CODE: TX.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10439118

FORD FUSION 2010 car safety problem was reported on Dec 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. while driving approximately 55 mph, the vehicle decelerated abnormally. the contact stopped the vehicle and shifted into park as the vehicle began to shake vigorously and stalled. the vehicle was taken to the dealer for diagnostics and stalled a second time on while in route. the technician was unable to diagnose the failure because the computer was not providing a failure code. the failure recurred three times. the third time, the vehicle was towed to the dealer and the technician advised that the computer was not reading a failure code but the electronic throttle body would likely have to be replaced. the vehicle was not repaired. the approximate failure mileage was 43,000. updated 03/02/12*lj the consumer stated the rear window, weather stripping on the doors, and door handles had to be replaced. the consumer stated there have been numerous problems with the transmission. updated 03/08/12.Mileage was 43000 miles. Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in SAN ANTONIO, TX. Original Owner. Vehicle was purchased on Nov 01, 2009. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 55 mph. DEALER'S NAME: RED MCCOMBS . DEALER'S TELEPHONE NUMBER: 210-357-1437 . DEALER'S CITY: SAN ANTONIO . DEALER'S STATE CODE: TX.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10439118

FORD FUSION 2010 car safety problem was reported on Dec 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . tl* the contact owns a 2010 ford fusion. while driving approximately 55 mph, the vehicle decelerated abnormally. the contact stopped the vehicle and shifted into park as the vehicle began to shake vigorously and stalled. the vehicle was taken to the dealer for diagnostics and stalled a second time on while in route. the technician was unable to diagnose the failure because the computer was not providing a failure code. the failure recurred three times. the third time, the vehicle was towed to the dealer and the technician advised that the computer was not reading a failure code but the electronic throttle body would likely have to be replaced. the vehicle was not repaired. the approximate failure mileage was 43,000. updated 03/02/12*lj the consumer stated the rear window, weather stripping on the doors, and door handles had to be replaced. the consumer stated there have been numerous problems with the transmission. updated 03/08/12.Mileage was 43000 miles. Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in SAN ANTONIO, TX. Original Owner. Vehicle was purchased on Nov 01, 2009. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 55 mph. DEALER'S NAME: RED MCCOMBS . DEALER'S TELEPHONE NUMBER: 210-357-1437 . DEALER'S CITY: SAN ANTONIO . DEALER'S STATE CODE: TX.

Ford Fusion 2010 Electrical System Instrument Panel

Ford Fusion 2010 Electrical System Instrument Panel Review #10439325

FORD FUSION 2010 car safety problem was reported on June 05, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM: INSTRUMENT PANEL . my trip odometer continues to malfunction despite being replaced with a brand new instrument cluster. i will park the vehicle, reset the trip odometer to 0.0, and when i return the next day or several hours later the trip odometer will increase in mileage by itself! for example, the trip odometer will now read 0.1, 0.4, 0.6, 0.7, or 0.9. apparently this is a design flaw within the instrument cluster for this vehicle that i am responsible for discovering, which explains the warranty providing me with a brand new instrument cluster. the ford dealership claims that the trip odometer is rounding off to the tenth based upon the current tenth that the main odometer is on. i questioned the dealership on the fact of whether or not my main odometer was being compromised? while the main odometer is causing the trip odometer to move without being driven, can the trip odometer cause the main odometer to move without being driven as well? the dealership told me no, but it is possible that this situation could be a two way street, and if it is then ford is guilty of odometer fraud!!!!! *tr.Mileage was 5500 miles. Vehicle Identification Number (VIN):3FAHP0JG1AR. Ford Fusion 2010 problem was reported in BEVERLY HILLS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10439331

FORD FUSION 2010 car safety problem was reported on Dec 09, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . my car is equipped with the 6f35 6 speed automatic transmission and has been experiencing lingering defects. i took my car in to a ford dealership in late november 2011 and notified them of transmission problems. my invoice reads, reprogram pcm to latest level and reset fluid level per tsb 11-11-23. the problems continue. i will admit that the flaring problem has improved, although the remaining problems persist while the overall feeling of transmission degradation seems to be accelerated. my trans. continues to struggle and feel worn out during low end acceleration. an inspection of my vehicle from a professional mechanic discovered burned up clutch material within the contaminated transmission fluid. he showed it to me, and i saw it with my own eyes. the dealership i was just at wasn't able to find any burned up clutch material in my fluid or the left front axle half shaft seal leak which my mechanic also discovered upon his inspection. i find it very fishy that these 2 problems automatically disappeared by themselves, it seems to me that the field service engineer from ford made repairs to my vehicle while it was in his or her possession during the defendants legal inspection for my lemon law suit at elder ford in troy, michigan. what ford did to my car was illegal, a defendants inspection allows for observation only, not repairs. i continue to experience very hard abnormal shifting while driving in city conditions and an uncontrollable forward lurch/jolt while driving in city conditions which is extremely unsafe. sometimes i will have a delayed engagement into drive. the shuddering vibration coming from the front end of the vehicle after driving the car for a short while continues. i continue to have an intermittent problem dealing with a burning oil or greasy smell coming through the air vents. the abnormal high pitched humming drone sound continues. *tr.Mileage was 16100 miles. Vehicle Identification Number (VIN):3FAHP0JG1AR. Ford Fusion 2010 problem was reported in BEVERLY HILLS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 28 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10439865

FORD FUSION 2010 car safety problem was reported on July 06, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact started the ignition and pressure applied to the brake pedal, the vehicle began to unexpectedly surge forward. the contact applied the brake pedal repeatedly before coming to a stop. the similar failure occurred on two separate occasions. the vehicle was taken to an authorized dealer three different times where they were unable to duplicate the problem. the manufacturer was made aware of the unintended acceleration. the approximate failure mileage was 22,000. updated 02/03/12*lj the consumer stated after the floor mats were removed, the sudden acceleration occurred again. updated 02/10/12.Mileage was 22000 miles. Vehicle Identification Number (VIN):3FAHP0HA9AR. Ford Fusion 2010 problem was reported in MACHIAS, NY. Original Owner. Vehicle was purchased on July 02, 2010. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. DEALER'S NAME: SIMMONE ROCKWELL FORD . DEALER'S TELEPHONE NUMBER: 607-324-4444 . DEALER'S CITY: HORNELL . DEALER'S STATE CODE: NY. DEALER'S ZIPCODE: 14843 .

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10440830

FORD FUSION 2010 car safety problem was reported on Nov 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . i own a 2010 ford fusion which we purchased october 2010. i brought my car to my local repair/inspection provider (not the ford dealer) to have oil change, tire rotation and inspection sticker. while my car was there it was noted that one of the wheel studs (front passenger) was snapped off and appeared to have happened awhile ago because the exposed component was rusted. it was recommended that i contact ford dealer to see if covered under warranty and inspection could not proceed until repaired. i brought it to ford dealer where car was purchased the next day. they stated it was not covered and would not even inspect it for defects. stated there was no possible way it could fracture on its own and must have happened at previous repair shop when they were taking the wheels off for rotation. they stated it would cost approximately $125 to repair one stud. i declined and returned to the previous repair shop where it was repaired for half the cost. it should also be noted that my tires had never been serviced before and this defect was noted prior to the rotation. *tr.Vehicle Identification Number (VIN):3FAHP0HA2AR. Ford Fusion 2010 problem was reported in LAKEVILLE, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10440882

FORD FUSION 2010 car safety problem was reported on Sept 20, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . this has happened a number of times since it started a few months ago, but soon after starting and driving down the road, the fusion suddenly loses power, the wrench light comes on the dash, and the idle is very rough. there is no acceleration possible. we have to coast to a stop, turn off the engine, then restart the car. this seems to reset the problem and things get back to normal. we've had the dealer look at it twice now. they suspect a throttle body problem. fortunately for us, we are still under warranty, but it is very disconcerting and a bit dangerous for this to happen. one time i was driving on the highway around 60 mph and it happened. i had to coast to the emergency lane while multiple cars passed me and swerved around me. this problem occurred yesterday three times in one 30 minute period. the dealer said that ford has given them no help in solving the problem. we almost bought a toyota camry instead of the fusion. i guess we should have done that. *tr.Mileage was 27500 miles. Vehicle Identification Number (VIN):3FAHP0JG7AR. Ford Fusion 2010 problem was reported in SPRINGFIELD, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Fuel System, Gasoline

Ford Fusion 2010 Fuel System, Gasoline Review #10440882

FORD FUSION 2010 car safety problem was reported on Sept 20, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE . this has happened a number of times since it started a few months ago, but soon after starting and driving down the road, the fusion suddenly loses power, the wrench light comes on the dash, and the idle is very rough. there is no acceleration possible. we have to coast to a stop, turn off the engine, then restart the car. this seems to reset the problem and things get back to normal. we've had the dealer look at it twice now. they suspect a throttle body problem. fortunately for us, we are still under warranty, but it is very disconcerting and a bit dangerous for this to happen. one time i was driving on the highway around 60 mph and it happened. i had to coast to the emergency lane while multiple cars passed me and swerved around me. this problem occurred yesterday three times in one 30 minute period. the dealer said that ford has given them no help in solving the problem. we almost bought a toyota camry instead of the fusion. i guess we should have done that. *tr.Mileage was 27500 miles. Vehicle Identification Number (VIN):3FAHP0JG7AR. Ford Fusion 2010 problem was reported in SPRINGFIELD, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Service Brakes, Hydraulic

Ford Fusion 2010 Service Brakes, Hydraulic Review #10440987

FORD FUSION 2010 car safety problem was reported on Dec 12, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC . tl* the contact owns a 2010 ford fusion. the contact was driving approximately 60 mph when she heard a loud noise coming from the vehicle. the vehicle was taken to the dealer the following morning where the dealer advised the contact that the rear brake pads were severely rusted and had damaged the rotors. the vehicle was repaired. the manufacturer was contacted and they offered no assistance. the failure mileage was approximately 17,900. the vin was unavailable. .Mileage was 17900 miles. Ford Fusion 2010 problem was reported in CLINTON, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10441304

FORD FUSION 2010 car safety problem was reported on Dec 23, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . tl* the contact owns a 2010 ford fusion. while driving approximately 35 mph, the vehicle began to jerk, shake and decelerate abnormally. the contact shut off the vehicle and after restarting, was able to drive without a failure. the vehicle was not taken to the dealer for diagnostic testing or repairs. the approximate failure mileage was 28,000. updated 02/15/12*lj the vehicle was taken to the dealer on dec 28th and was returned to the consumer the next day. the dealer was unable to diagnose the problem. the second time the incident occurred. the dealer was able to pull up code from the vehicle's computer, which stated the throttle body needed to be replaced, along with a new battery. updated 02/29/12.Mileage was 28000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in ST LOUIS, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph. DEALER'S NAME: DAVE SINCLAIR FORD .

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10441304

FORD FUSION 2010 car safety problem was reported on Dec 23, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. while driving approximately 35 mph, the vehicle began to jerk, shake and decelerate abnormally. the contact shut off the vehicle and after restarting, was able to drive without a failure. the vehicle was not taken to the dealer for diagnostic testing or repairs. the approximate failure mileage was 28,000. updated 02/15/12*lj the vehicle was taken to the dealer on dec 28th and was returned to the consumer the next day. the dealer was unable to diagnose the problem. the second time the incident occurred. the dealer was able to pull up code from the vehicle's computer, which stated the throttle body needed to be replaced, along with a new battery. updated 02/29/12.Mileage was 28000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in ST LOUIS, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph. DEALER'S NAME: DAVE SINCLAIR FORD .

Ford Fusion 2010 Electrical System Battery

Ford Fusion 2010 Electrical System Battery Review #10441304

FORD FUSION 2010 car safety problem was reported on Dec 23, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:BATTERY . tl* the contact owns a 2010 ford fusion. while driving approximately 35 mph, the vehicle began to jerk, shake and decelerate abnormally. the contact shut off the vehicle and after restarting, was able to drive without a failure. the vehicle was not taken to the dealer for diagnostic testing or repairs. the approximate failure mileage was 28,000. updated 02/15/12*lj the vehicle was taken to the dealer on dec 28th and was returned to the consumer the next day. the dealer was unable to diagnose the problem. the second time the incident occurred. the dealer was able to pull up code from the vehicle's computer, which stated the throttle body needed to be replaced, along with a new battery. updated 02/29/12.Mileage was 28000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in ST LOUIS, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph. DEALER'S NAME: DAVE SINCLAIR FORD .

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10442309

FORD FUSION 2010 car safety problem was reported on Dec 14, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . lost parking function on the transmission. parking function is missing causing the vehicle to move after i park the car. didn't realize until after i parked my car. was walking towards the building that i noticed that the car was rolling back and had to run back, unlock the car and then push the brake. after investigating realized that the "p" function was missing. did hear a huge clunking noise when i tried to park in the first place. this is a safety issue and action needs to be taken to address this issue and make ford provide an explanation for the 2.5 l 6f35 transmission. the dealer diagnosed the vehicle with a bad transmission and the parking pawl broken inside the transmission. it was necessary to use parking brake to keep the car steady during parking. *tr.Mileage was 14947 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in ROCHESTER HILLS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Power Train Review #10443348

FORD FUSION 2010 car safety problem was reported on Dec 16, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . "unknown or other" in this case would likely relate to "power train" and/or "electrical," but definitely relates to public safety. the ignition tumbler releases the key in any position--park, neutral, drive, or low--rather than in only park. drivers of cars with manual transmissions are accustomed to setting hand brakes using gears. prior the the date of incident above, i recall moving slightly forward on a slight slope, and i simply applied the hand brake to avoid putting more strain on drive components. after a dead battery (due to lighted dash gear position indicator) and a jump start, it was days later that i realized that the key had been removed with the car in gear. the ford dealer and ford motor company say repair consists of replacing the shift assembly (includes sending unit which has no "output") at a cost to me of $487.65 + tax. they claim this is not a power train issue and that my "cpo" expired less than a month earlier, this on a ford "certified" car. public safety is involved because a rolling car can cause havoc. *tr.Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in VALLEY SPRINGS, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train Review #10443978

FORD FUSION 2010 car safety problem was reported on Sept 30, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . on september 30th i was driving home and i had only driven less than a mile at approximately 35 miles per hour when the wrench light appeared on my dash and my car quick moving. i was able to get it to move about 1 mile per hour so i got the car off the road and shut it off. it was dark and i was alone. i was going to call aaa for a tow and i decided i would try to start the car and see what would happen. the wrench light was gone and the car was moving like nothing was wrong with it. this happened again on oct 5th and oct 7th during rush hour traffic and both times i was fortunate that i was able to get out of traffic to avoid getting hit both times my speed was approximately 45 mph. i have taken the car to two car repair shops and they can not find any thing wrong with it when they connect it to their diagnostic machine. from september to current date the car has done this at least another 10 times. sometimes the speed may be at 55 or 60 miles per hour. i did contact the local ford dealer and i wrote a letter to the ford company neither party has done anything to help me. there is a defective in their product. the local ford dealer suggested it may be value body and throttle body issue. i continue to drive the car to work and back waiting for it to break down or to be killed in an accident when it quits in the middle of a busy highway and i am unable to get out of the line of traffic. so much for the commercial "number 1 most dependable car in america ". my ford fusion sucks. *tr.Mileage was 86000 miles. Vehicle Identification Number (VIN):3FAHP0HAXAR. Ford Fusion 2010 problem was reported in LEXINGTON, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Power Train Review #10444461

FORD FUSION 2010 car safety problem was reported on Feb 19, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . at 18540 miles the transmission failed and the dealership had to rebuilt it and reprogram the pcm. then the car was taken back 5 months later with 30100 they had it a week but could not duplicate the problem. we then towed the car to alabama and less then a month later the transmission failed again at 31111 miles at this time it was in the shop 36day the car was pick up and drove 12 miles and the transmission failed again. the dealership then had it another 14 day. a month and a half later the transmission failed again, the dealership had it 3 days. we drove it 35 miles and the transmission failed again and the dealership had it another 17 days.then we had the car for a month and the transmission failed again with 36000 miles on it. the dealership had it for 16 days. ford corp has not allowed the dealership to replace the transmission, but has authorized them to rebuild and reprogram pcm numerous times. we have the car now and it is still not shifting right. we have talk to ford and they will not doing anything for us. told us the car is fixed....or is it. this car has become a safety hazard because you do not know when the transmission is going to fail in heavy traffic and create a dangerous condition. we fear for our safety when we drive this car. .Mileage was 18540 miles. Vehicle Identification Number (VIN):3HAHP0HA3AR. Ford Fusion 2010 problem was reported in PHENIX CITY, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Visibility

Ford Fusion 2010 Visibility Review #10444544

FORD FUSION 2010 car safety problem was reported on Jan 12, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY . in cold/inclement weather, the wipers will not stay defrosted and will freeze to the windshield & not come on, or will not clean the windshield for enough visibility to see the road while driving which can cause a crash. this is due to the fact that the wipers sit too far below the defroster vents on the car. i let my car warm up for 15 mins on dec 12th and made sure they were clean before i got on the parkway. after being on the road 20 minutes & leaving my defroster on high, i turned my wipers on to clear the dirty water/slush thrown on my car by 18 wheelers. the wipers stuck again, and i ran off the side of the road by looking out the side windows to prevent an accident. i had to pry the wipers off the windshield because they had froze again. this is the third time this has happened to me. the other two times were in 2010. i couldn't remember the first two dates, so i used the most current as the info above including mileage. i try to avoid driving my car during freezing moist conditions because i'm scared i will wreck. i notified ford a few days ago and they are looking into the situation, but they told me there has not been a recall. i shouldn't be scared to drive my car! *tt.Mileage was 45000 miles. Vehicle Identification Number (VIN):3FAHP0JA8AR. Ford Fusion 2010 problem was reported in CLARKSON, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10444608

FORD FUSION 2010 car safety problem was reported on Jan 19, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . the powertrain has suddenly caused major problems. my car will no longer reverse and more importantly as far as safety is concerned, the gears may sometimes not engage while accelerating causing the car to rev up the rpm's without moving forward. *tt.Ford Fusion 2010 problem was reported in PASSAIC, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10444733

FORD FUSION 2010 car safety problem was reported on Dec 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . when driving in snow or slush, there is build up in the wheels causing the vehicle to have extreme vibration making it unable to drive until the wheels are cleaned out of snow or slush. this happens every time there is snow or slush on the roadways. i live in a northern state, so this causes some concern for safety. this may also be the cause of missing lugnuts that have been reported on other websites. *tr.Vehicle Identification Number (VIN):3FAHP0JA5AR. Ford Fusion 2010 problem was reported in KENNAN, WI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Wheels Review #10445050

FORD FUSION 2010 car safety problem was reported on Apr 08, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . tl* the contact owns a 2010 ford fusion. the contact stated that the rear wheels and the front driver side wheel was bent abnormally. both rear wheels were replaced because the of the failure, but the front one had not. the dealer told the contact that the failure was caused by the way the vehicle was being driven. the contact did not agree and believed the failure was caused by a manufacturing defect. the failure mileage was 9,000 and the current mileage was 27,000. updated 02/15/12*lj updated 02/22/12.0 person(s) were injured. 0 person(s) died.Mileage was 9000 miles. Vehicle Identification Number (VIN):3FAHP0KC8AR. Ford Fusion 2010 problem was reported in COLUMBUS, OH. Vehicle was purchased on Feb 13, 2009. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. DEALER'S NAME: RICART AUTOMOTIVE . DEALER'S TELEPHONE NUMBER: 614-836-6300 . DEALER'S CITY: COLUMBUS . DEALER'S STATE CODE: OH. DEALER'S ZIPCODE: 43227 .

Ford Fusion 2010 Wheels Review #10445177

FORD FUSION 2010 car safety problem was reported on Jan 23, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . tl* the contact owns a 2010 ford fusion. the contact stated that she received notification of nhtsa campaign id number: 11v574000 (wheels:lugs/nuts/bolts) and after contacting the dealer to schedule an appointment for repairs, she was advised that the parts needed for recall repairs were not yet available. the manufacturer was contacted and they advised her that the parts would not be available to the dealer until the end of february. the contact had not experienced a failure. the current mileage was approximately 52,000. the vin was unavailable. .Ford Fusion 2010 problem was reported in HARRISBURG, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Service Brakes, Hydraulic

Ford Fusion 2010 Service Brakes, Hydraulic Review #10445423

FORD FUSION 2010 car safety problem was reported on Jan 17, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC . rear brake pads and rotors rust together when there is moisture in air and parking brake is used. rear brake rotors rotted badly on inside edge. right rotor completly failed brake pad draging. 16 inch alloy wheels. *tr.Mileage was 31506 miles. Vehicle Identification Number (VIN):3FAHP0GA7AR. Ford Fusion 2010 problem was reported in PRINCETON, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10445468

FORD FUSION 2010 car safety problem was reported on Jan 23, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . tl* the contact owns a 2010 ford fusion. the contact stated that the vehicle was included in the recall associated with nhtsa campaign id number 11v574000 (wheels: lugs/nuts/bolts). the authorized dealer was notified, but stated that recall parts were on back order and they were unable to provide an estimated arrival date for the parts. the vehicle would be repaired when the part became available. the manufacturer was made aware of the problem and provided no further assistance. the contact had not experienced any failure related to the recall defect. the failure mileage was unknown. .Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in CORAL SPRINGS, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10445565

FORD FUSION 2010 car safety problem was reported on Jan 16, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while driving down the interstate, the fusion began to jerk and shake due to the transmission slipping, causing the car to lose its speed very quickly, almost causing a wreck. the dealership ended up having to do a complete transmission overhaul at only 13,000 miles. the problem came back around 20,000 miles and the dealership said it needed its codes reprogrammed. the problem persisted and around 70,000 miles, the vehicle began doing the same thing. again while driving on the interstate, the car's transmission started slipping and the vehicle shook and jerked. now the dealership conveniently recommends a new transmission, now that i am outside of my warranty at a cost of $4,000! this is a very dangerous situation and having a newborn child in the vehicle makes it even more alarming. i do not feel safe in this car and strongly feel that ford needs to make its customers whole by recalling the transmission components entirely. *tr.Mileage was 75000 miles. Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in LOCUST GROVE, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train Review #10445759

FORD FUSION 2010 car safety problem was reported on Jan 28, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . when we took it in for normal service of oil change the technician brought out the transmission dipstick to show that it was as black as the oil. we had it changed for over $120 . the car is shifting much better than when we bought it but the owners service manual states that it should not be changed until 60,000 miles. we feel that it should be handled and covered by the dealer. *tt.Mileage was 41100 miles. Vehicle Identification Number (VIN):3FAHP0HA9AR. Ford Fusion 2010 problem was reported in SWANSEA, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10446097

FORD FUSION 2010 car safety problem was reported on Jan 30, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . i have a 2010 ford fusion hybrid which i love driving and i believe it is one of the best cars out there. the problem is with 12,000 miles on the car the tires were wearing out very fast and at 18,000 they were worn where it wasn't safe to drive the car. i had to buy new tires. the dealer said there was no warranty on the tires and they wanted $1182.00 for replacement ones. mind you, i buy the three year full maintenance on the vehicle as well. i heard from other fusion drivers that even buying new tires, the wear is very fast. something is very wrong here and ford is not admitting it. *tr.Mileage was 18001 miles. Vehicle Identification Number (VIN):3FADP0L36AR. Ford Fusion 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Tires

Ford Fusion 2010 Tires Review #10446097

FORD FUSION 2010 car safety problem was reported on Jan 30, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with TIRES . i have a 2010 ford fusion hybrid which i love driving and i believe it is one of the best cars out there. the problem is with 12,000 miles on the car the tires were wearing out very fast and at 18,000 they were worn where it wasn't safe to drive the car. i had to buy new tires. the dealer said there was no warranty on the tires and they wanted $1182.00 for replacement ones. mind you, i buy the three year full maintenance on the vehicle as well. i heard from other fusion drivers that even buying new tires, the wear is very fast. something is very wrong here and ford is not admitting it. *tr.Mileage was 18001 miles. Vehicle Identification Number (VIN):3FADP0L36AR. Ford Fusion 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10446264

FORD FUSION 2010 car safety problem was reported on Nov 16, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . 1 bought a ford fusion in aug. 2011 used w/15,000 miles on it no problems with it until after i reached 32,000 miles the transmission slips and the wheels sound like its going to fall off , it somes seam to jump out of gear while driving and starting and stopping . i took if to a ford dealer for oil change told service tech about this he said nothing wrong with car never took for test drive. i did some looking on-line there are a lot of people saying same thing. i read about a re-call on transmission called dealer brought car from said they didn't get notice . sent e-mail to ford no reply. can not get answers from no-one . i have young children i don't want to be driving down the road and have wheels fall off or transmission fall out. this seams to be getting worst . *kb.Ford Fusion 2010 problem was reported in DUNDALK, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10446264

FORD FUSION 2010 car safety problem was reported on Nov 16, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . 1 bought a ford fusion in aug. 2011 used w/15,000 miles on it no problems with it until after i reached 32,000 miles the transmission slips and the wheels sound like its going to fall off , it somes seam to jump out of gear while driving and starting and stopping . i took if to a ford dealer for oil change told service tech about this he said nothing wrong with car never took for test drive. i did some looking on-line there are a lot of people saying same thing. i read about a re-call on transmission called dealer brought car from said they didn't get notice . sent e-mail to ford no reply. can not get answers from no-one . i have young children i don't want to be driving down the road and have wheels fall off or transmission fall out. this seams to be getting worst . *kb.Ford Fusion 2010 problem was reported in DUNDALK, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train Automatic Transmission Review #10446665

FORD FUSION 2010 car safety problem was reported on Jan 29, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . vehicle has problem shifting gears, slows down, then it starts to go. i have taken it into ford 3 separate times, a recall was done on the vehicle for a computer chip, again had the vehicle into service in 09/2011 for the same issue. the vehicle has 34,000 miles on it and attempt to replace the rear brakes...driver rear side had no pad left, checked the three other brakes plenty of pad. surburban ford service desk told me because my car was green metallic, not covered in latest recall. i looked at the recall notices and it is absolutely the same problem i've been complaining about from the first month i purchased this vehicle! *kb.Mileage was 2635 miles. Vehicle Identification Number (VIN):3FAHP0HA4AR. Ford Fusion 2010 problem was reported in CLINTON TOWNSHIP, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Service Brakes, Hydraulic

Ford Fusion 2010 Service Brakes, Hydraulic Review #10446665

FORD FUSION 2010 car safety problem was reported on Jan 29, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC . vehicle has problem shifting gears, slows down, then it starts to go. i have taken it into ford 3 separate times, a recall was done on the vehicle for a computer chip, again had the vehicle into service in 09/2011 for the same issue. the vehicle has 34,000 miles on it and attempt to replace the rear brakes...driver rear side had no pad left, checked the three other brakes plenty of pad. surburban ford service desk told me because my car was green metallic, not covered in latest recall. i looked at the recall notices and it is absolutely the same problem i've been complaining about from the first month i purchased this vehicle! *kb.Mileage was 2635 miles. Vehicle Identification Number (VIN):3FAHP0HA4AR. Ford Fusion 2010 problem was reported in CLINTON TOWNSHIP, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10446707

FORD FUSION 2010 car safety problem was reported on Apr 26, 2011.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . transmission slip into neutral and revs past 4000rpm, 1-2 & 2-3, also severe hesitation when slow down then try to speed up again (i.e. stop & go traffic). has put me in unsafe situations requiring defensive driving to avoid an accident. has been in for service 4+ times and each time only "calibration". service dept is very helpful but hindered by ford motor company's inability to solve defect. also, was given print out of ford advising service that the 2-3 hesitation is " deemed normal and it meets design intent at this time".100% unsafe to drive, especially with children in car as the gear slipping and or hesitation followed by suddenly engaging then speeding up puts the driver in unpredictable conditions. has put me in numerous near accidents (specifically when merging or changing lanes and yielding to turn left). most recent "fix" was 2/2/12 and transmission still slipping, hesitating, slamming into gear. have filed with bbb auto line. ford motor co. needs to seriously address this from safety standpoint. *kb *tr.Mileage was 21194 miles. Vehicle Identification Number (VIN):3FAHP0HA2AR. Ford Fusion 2010 problem was reported in TEMPE, AZ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10446707

FORD FUSION 2010 car safety problem was reported on Apr 26, 2011.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . transmission slip into neutral and revs past 4000rpm, 1-2 & 2-3, also severe hesitation when slow down then try to speed up again (i.e. stop & go traffic). has put me in unsafe situations requiring defensive driving to avoid an accident. has been in for service 4+ times and each time only "calibration". service dept is very helpful but hindered by ford motor company's inability to solve defect. also, was given print out of ford advising service that the 2-3 hesitation is " deemed normal and it meets design intent at this time".100% unsafe to drive, especially with children in car as the gear slipping and or hesitation followed by suddenly engaging then speeding up puts the driver in unpredictable conditions. has put me in numerous near accidents (specifically when merging or changing lanes and yielding to turn left). most recent "fix" was 2/2/12 and transmission still slipping, hesitating, slamming into gear. have filed with bbb auto line. ford motor co. needs to seriously address this from safety standpoint. *kb *tr.Mileage was 21194 miles. Vehicle Identification Number (VIN):3FAHP0HA2AR. Ford Fusion 2010 problem was reported in TEMPE, AZ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10447030

FORD FUSION 2010 car safety problem was reported on Sept 06, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . since i purchased my ford fusion in 2010, i have had nothing but problems. not only mechanical but, also with the dealership. my car shuts off while driving all the time. additionally, it shakes and jerks. the dealership initially was responsive to my calls and concerns. for the last few months, that has not been the case. the car has been in the shop five different times, to include today ? all for the same thing as listed above. each time, i was told they had fixed the issue. in addition, they said they would wash/fill up the gas to where i left it. this was done correct once. at one point, my car was in the shop for a month. they decided the transmission needed to be replaced ? which they would do free of charge. on the day this repair was to be made, they all of a sudden changed their minds and reneged on that commitment - claiming they had found the real issue which, as it turns, out they did not. when i had come to pick up my vehicle, i found a pack of cigarettes in my middle console all half smoked. obviously, someone was smoking in my car which should not be allowed. *tr since i was getting nowhere, the service manager suggested i file a claim with the ford replacement car program. i was told by dj, koon? sales manager, the replacement process should take only a week. he even suggested that i should not make another payment on my vehicle. i started this claim process on december 1, 2011. i was finally sent a breakdown worksheet from corporate, in particular, jeff terrell, on february 3, 2012. he stated i would need to pay nearly $6,000 up front for the used miles on my car. also, he said in order for them to set me up with a replacement vehicle, i would have to take out another loan. i wrote him back immediately on february 3, 2012 and again today, february 7, asking how he came to that amount. i have yet to hear back from him. *tr.Mileage was 21000 miles. Vehicle Identification Number (VIN):3FAHP0JA4AR. Ford Fusion 2010 problem was reported in ANNANDALE, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10447033

FORD FUSION 2010 car safety problem was reported on Feb 09, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i have a ford fusion with about 30000 miles. i first noticed a hard shift at 10k miles and thought maybe its just a simple fix. i took it in and they reprogrammed the transmission and the service supervisor said that this transmission adapts to the owners driving habits. well 3k miles later its worse so i take it back and the tech said all the clutches were replaced and two other things were done! i have taken it back four more times and have not had it fixed. it appears that ford admitted there was a problem with a transmission code that fixes the problem. however, the problem was not fixed and i am left with a vehicle that also had a window motor replaced, some pulleys that were making a whistling noise, and a battery and taillight that went out changed. i don't know if its a lemon, but i smell disaster in the next couple of years! wish ford would do the right thing and stand by its product. *tr.Mileage was 20 miles. Ford Fusion 2010 problem was reported in SAN ANTONIO, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Visibility Power Window Devices And Controls

Ford Fusion 2010 Visibility Power Window Devices And Controls Review #10447033

FORD FUSION 2010 car safety problem was reported on Feb 09, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:POWER WINDOW DEVICES AND CONTROLS . i have a ford fusion with about 30000 miles. i first noticed a hard shift at 10k miles and thought maybe its just a simple fix. i took it in and they reprogrammed the transmission and the service supervisor said that this transmission adapts to the owners driving habits. well 3k miles later its worse so i take it back and the tech said all the clutches were replaced and two other things were done! i have taken it back four more times and have not had it fixed. it appears that ford admitted there was a problem with a transmission code that fixes the problem. however, the problem was not fixed and i am left with a vehicle that also had a window motor replaced, some pulleys that were making a whistling noise, and a battery and taillight that went out changed. i don't know if its a lemon, but i smell disaster in the next couple of years! wish ford would do the right thing and stand by its product. *tr.Mileage was 20 miles. Ford Fusion 2010 problem was reported in SAN ANTONIO, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10447033

FORD FUSION 2010 car safety problem was reported on Feb 09, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . i have a ford fusion with about 30000 miles. i first noticed a hard shift at 10k miles and thought maybe its just a simple fix. i took it in and they reprogrammed the transmission and the service supervisor said that this transmission adapts to the owners driving habits. well 3k miles later its worse so i take it back and the tech said all the clutches were replaced and two other things were done! i have taken it back four more times and have not had it fixed. it appears that ford admitted there was a problem with a transmission code that fixes the problem. however, the problem was not fixed and i am left with a vehicle that also had a window motor replaced, some pulleys that were making a whistling noise, and a battery and taillight that went out changed. i don't know if its a lemon, but i smell disaster in the next couple of years! wish ford would do the right thing and stand by its product. *tr.Mileage was 20 miles. Ford Fusion 2010 problem was reported in SAN ANTONIO, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Equipment Electrical Radio/tape Deck/cd Etc.

Ford Fusion 2010 Equipment Electrical Radio/tape Deck/cd Etc. Review #10447051

FORD FUSION 2010 car safety problem was reported on Jan 31, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC. . my cd player stopped working without any warning. i took my car to the dealer on 1/31/12 to see what was the problem. i waited all day and finally got a phone call saying that the cd player was being replaced. i asked what the problem was and my question was ignored and again i was told it was being replaced but the new cd player wouldn't be in until the next day. i returned there again today because i got an error message on my sirius radion saying "fault". i called sirius radio and they said that ford needed to replace the satellite module. by the time i reached the dealership it was working again but just as i was about to pull off, it had the error message again "fault". they gave me a loaner and i guess they will call me tomorrow with an update. *tr.Vehicle Identification Number (VIN):3FAHP0KC4AR. Ford Fusion 2010 problem was reported in GREENVILLE, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10447110

FORD FUSION 2010 car safety problem was reported on Jan 24, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . tl* the contact owns a 2010 ford fusion. the contact stated that the vehicle was taken to an authorized dealer for repairs under nhtsa campaign id number 11v574000 (wheels: lugs/nuts/bolts); however the part was unavailable. the vehicle had been at the dealer for two weeks and continued to remain until the part was to become available. the manufacturer was not notified of the problem. the contact had not experienced prior failure regarding the recall defect. .Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in WOODBRIDGE, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Wheels Lugs/nuts/bolts

Ford Fusion 2010 Wheels Lugs/nuts/bolts Review #10447112

FORD FUSION 2010 car safety problem was reported on Jan 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS:LUGS/NUTS/BOLTS . tl* the contact owns a 2010 ford fusion. the contact stated that the vehicle was included in the recall associated with nhtsa campaign id number: 11v574000 (wheels:lugs/nuts/bolts). an authorized dealer was notified and the contact was informed that the parts needed for recall repairs were not available. the contact continued to notify the dealer for approximately one month and was constantly informed that the parts were not yet available. the manufacturer was made aware of the failure and could not provide a timetable for when the parts would become available. the vehicle was not repaired. the failure mileage was 1,300. update 03/05/12*lj.Mileage was 1300 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in CINCINNATI, OH. Vehicle was purchased on May 01, 2010. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph. DEALER'S NAME: WALT SEVERENY . DEALER'S TELEPHONE NUMBER: 373-347-4957 .

Ford Fusion 2010 Wheels Lugs/nuts/bolts Review #10447360

FORD FUSION 2010 car safety problem was reported on Jan 12, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS:LUGS/NUTS/BOLTS . tl* the contact owns a 2010 ford fusion. the contact stated the vehicle was included in a recall associated with nhtsa campaign id number 11v574000 (wheels:lugs/nuts/bolts). an authorized dealer was notified and informed the contact that the parts necessary to remedy the failure were not available. the parts have not been available for approximately one month. the vehicle was not repaired. the manufacturer was not made aware of the failure. the failure mileage was 7,800. updaetd 03/14/12*lj updated 04/09/12.Mileage was 7800 miles. Vehicle Identification Number (VIN):3FAHP0HA9AR. Ford Fusion 2010 problem was reported in CARROLLTON, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10447872

FORD FUSION 2010 car safety problem was reported on Feb 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . the transmission does not shift correctly. the engine will rev up and the transmission will shift hard when it shifts. especially when going up hill or under heavy acceleration the engine my red line before shifting. *tr.Mileage was 30000 miles. Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in WESTFIELD, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Power Train Review #10448387

FORD FUSION 2010 car safety problem was reported on Feb 13, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . my 2010 fusion se v6 with the infamous 6f35 transmission is slipping, hard shifting, fluid is blacked and or burnt. my concern is that it also has just lurched forward for no reason. i feel it is a safety issue and should be recalled for a new transmission. please force ford to issue a recall on this model transmission. i know i am not the only one with this issue on this vehicle. *tr.Mileage was 43000 miles. Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in HILMAR, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10449188

FORD FUSION 2010 car safety problem was reported on Nov 02, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . car had a faulty throttle body, which would cause the car to lose power. you could be running any speed and the car would jerk and you would have no power car would coast to the side of the road. very dangerous on the interstate or any heavy traffic. the dealer knew exactly what the problem was when i described it to him,which led me to believe they have seen this problem many times. checked online and saw where many others had the same problem. ford told me it was my problem and were sorry it had happened but there was nothing they could do. case #[xxx]. this is a very dangerous problem if the vehicle is in traffic.ford has had a recall on the transmission which was due to holes being drilled wrong on the throttle body. information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).*tr.Mileage was 45000 miles. Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in OLIVE BRANCH, MS. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10449396

FORD FUSION 2010 car safety problem was reported on Nov 14, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i have a ford fusion with about 35,500 miles. i bought the car used with about 18,000 miles and noticed inconsistent shifting right away. then progressed into not shifting back into gear right away after shifting out of reverse. i took it in and they reprogrammed the transmission and the service supervisor said that this transmission adapts to the owners driving habits. took it in again about a month later and they said the fluid was low; they weren't sure why just filled it and sent me on my way. third time i took it to a different dealership. they had to pull the transmission and replace parts, which took almost a week. it seemed okay at first but now is displaying the same issues as before of not shifting into gears when accelerating. the problem was not fixed and i am left with a vehicle that also had a heater motor replaced that were making a whistling noise, floor heat that barely comes out, car alarm that goes off even when all the doors are unlocked and bright lights that just randomly come on. i don't know if its a lemon, but i smell disaster in the next couple of years! wish ford would do the right thing and stand by its product. *tr.Mileage was 29285 miles. Vehicle Identification Number (VIN):3FAHPOHA8AR. Ford Fusion 2010 problem was reported in FENTON, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train Review #10449851

FORD FUSION 2010 car safety problem was reported on Nov 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i was driving on a 6 or 8 lane freeway when it suddenly downshifted to a much lower gear (probably 3rd) and the tachometer maxed at 7000 rpm and held there until i manually moved the shift lever to neutral. when i put it back in drive (still moving) it again raced to 7000 rpm and i put it in neutral and coasted to the side of the road. i put it in all the gears, then in drive and went back on the freeway. it stayed in 1st gear and i again went to the shoulder of the road. i shut the engine off, restarted it and got back on the freeway. it shifted ok, but after a few miles did it again. i sent my complaint to ford motor company, but they say they can't duplicate the actions and therefore can not/will not do anything about it. (see ford customer service case #0506021830 and my letter to them).0 person(s) were injured. 0 person(s) died.Mileage was 14000 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in FAYETTE, IA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 68 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10449851

FORD FUSION 2010 car safety problem was reported on Nov 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . i was driving on a 6 or 8 lane freeway when it suddenly downshifted to a much lower gear (probably 3rd) and the tachometer maxed at 7000 rpm and held there until i manually moved the shift lever to neutral. when i put it back in drive (still moving) it again raced to 7000 rpm and i put it in neutral and coasted to the side of the road. i put it in all the gears, then in drive and went back on the freeway. it stayed in 1st gear and i again went to the shoulder of the road. i shut the engine off, restarted it and got back on the freeway. it shifted ok, but after a few miles did it again. i sent my complaint to ford motor company, but they say they can't duplicate the actions and therefore can not/will not do anything about it. (see ford customer service case #0506021830 and my letter to them).0 person(s) were injured. 0 person(s) died.Mileage was 14000 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in FAYETTE, IA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 68 mph.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10449930

FORD FUSION 2010 car safety problem was reported on Dec 01, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . after driving our 2010 ford fusion in snow it would drive like the tires were out of balance (serious vibration after about 35-40 mph). i solved this problem by putting it in a heated garage overnight. i brought up my concern to a local ford service center. they acknowledged that this is a problem and suggested spraying the wheel area with a lubricant such as pam cooking oil to keep the snow and ice from collecting on the wheels. they felt that the problem was the aluminum rims (i think they said rims, something in the wheel). we recently had significant snow this winter which brought this problem back to my attention. i feel that this is an unacceptable design flaw in this car and would like it fixed. *tr.Mileage was 6000 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in GRAND RAPIDS, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Wheels Review #10450140

FORD FUSION 2010 car safety problem was reported on Mar 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . 3mar12 called dealer to get recall done and was told that the do not have the part. i had called previously on 13 feb12 and was told the samething, 3mar12 was put on a waiting list and don't know for how long. in the notice it stated to get recall done in a timely fashion. *tr.Ford Fusion 2010 problem was reported in STERLING, CT. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Wheels Review #10450362

FORD FUSION 2010 car safety problem was reported on Jan 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . tl* the contact owns a 2010 ford fusion. the contact stated that the vehicle was included in the recall associated with nhtsa campaign id number 11v574000 (wheels:lugs/nuts/bolts). an authorized dealer was notified and the contact was informed that the parts necessary to remedy the failure were not available. the manufacturer was also notified and stated that they had no time frame as to when the parts would become available. the vehicle was not repaired. the failure mileage was 23,500. .Mileage was 23500 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in GRIFFITHSVILLE, WV. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Service Brakes, Hydraulic

Ford Fusion 2010 Service Brakes, Hydraulic Review #10450446

FORD FUSION 2010 car safety problem was reported on Dec 05, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC . tl* the contact owns a 2010 ford fusion. the contact stated that when the vehicle was first started, there was a popping noise that was exhibited by the brake system. the contact stated that the noise would cease once the engine was warm. the dealer inspected the vehicle and discovered that the noise was caused by brake dust and advised that the noise should cease once the vehicle was running. the brake system was tested and there were no failures detected. the contact stated that the noise continued and progressively became worse. the vehicle was not repaired. the failure mileage was unknown, but the current mileage was 15,416. updated 03/27/12*lj the consumer stated the popping oise is still present and is o nly heard when the brake is appled and the noise would become louder. updated 04/09/12.Vehicle Identification Number (VIN):3FAHP0HG8AR. Ford Fusion 2010 problem was reported in WALDORF, MD. Vehicle was purchased on Dec 12, 2009. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. DEALER'S NAME: SHEEHY OF GAITHERSBURG . DEALER'S TELEPHONE NUMBER: 301-258-1015 . DEALER'S CITY: GAITHERSBURG . DEALER'S STATE CODE: MD. DEALER'S ZIPCODE: 20879 .

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10451068

FORD FUSION 2010 car safety problem was reported on Feb 17, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . first happened setting at a red light, light changed i took off and car stalled in intersection and lucky i was moving fast enough to get out of the way and off the road. second time i was going 60mph down road and car stalled losing power and the ability to brake and steer properly. car stalls and when restarted its rpms are very random, up and down , car shakes etc. then stalls again. took to ford and they cant find anything. this is a very unsafe problem that is occurring, and i have found dozens of people with the same problem on online forums... *tr.Mileage was 25000 miles. Ford Fusion 2010 problem was reported in PROCTORVILLE, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10451630

FORD FUSION 2010 car safety problem was reported on Jan 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . tl* the contact owns a 2010 ford fusion. the contact received notification of nhtsa campaign id number: 11v574000 (wheels:lugs/nuts/bolts) in january, 2012. the contact called the dealer numerous times to secure an appointment for recall repairs, but the dealer advised the contact that the parts needed to complete the repair were not available. the contact was worried that the failure would occur on the vehicle prior to being able to have the recall repairs performed on the vehicle. the manufacturer was not contacted. the vehicle was not repaired. the current mileage was 7,000. the contact had not experienced a failure. .Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in PERRYVILLE, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10452135

FORD FUSION 2010 car safety problem was reported on Mar 14, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . 2010 ford fusion will lose power at highway speed, car will not stall completely but will jerk and shake without enough power to get off road. tool light will come on, after restarting car will drive normal. sudden loss of power is extremely dangerous! how many crashes will it take before our government forces ford to fix the problem. took to mechanic, no codes to determine problem. ford .....step up stand behind your product! wife was almost ran over by tractor trailer! *tr.Mileage was 63000 miles. Ford Fusion 2010 problem was reported in HAMLET, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train Automatic Transmission

Ford Fusion 2010 Power Train Automatic Transmission Review #10452298

FORD FUSION 2010 car safety problem was reported on Feb 15, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . i bought the car with 12000 miles on it and under warranty. at 12750 miles the transmission began to flare from 2nd to 3rd gear and 4th to 5th gear. i took it to the dealer and the transmission was reprogrammed and i was told to drive it apx. 250 miles and it would correct itself. at 13150 miles the problem was worse than before so i took it back in. the dealer checked it and said nothing was wrong and that the cold transmission flare was" normal". i know that the transmission was not designed to flare until it gets warm. after viewing several hundred complaints on line, all for the same problem, it seems you would required ford to fix this problem. it is a big time safety hazard when the car looses power and forward motion in traffic. this defect is a major accident and probably deaths waiting to happen. please do something to help all of us since it is evident that ford does not care and will not take it on it's to fix the problem or stand behind their product..0 person(s) were injured. 0 person(s) died.Mileage was 12750 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in ALABASTER, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Wheels Lugs/nuts/bolts

Ford Fusion 2010 Wheels Lugs/nuts/bolts Review #10453047

FORD FUSION 2010 car safety problem was reported on Mar 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS:LUGS/NUTS/BOLTS . 2010 ford fusion. consumer writes in regards to safety recall notice concerning wheel studs *tgw the dealer informed the consumer, they only had one lug nut kit available . the consumer was informed he would be placed on a waiting list. as of march 10, 2012, the consumer has not received a call from the dealer. *jb.Ford Fusion 2010 problem was reported in FULDA, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10452554

FORD FUSION 2010 car safety problem was reported on Mar 05, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while attempting to pass a vehicle, the transmission completely disengaged from the engine as if it were in neutral leaving me with no power to the wheels. the revs on the engine were extremely high. as i was passing on the left, this left me in an extremely dangerous and vulnerable position as i had no power to move the vehicle. fortunately i was able to coast to the right at which time at a near stop the transmission violently re-engaged. first time, took to the dealership where they reprogrammed transmission. it has since happened again, again while accelerating to pass. it is just a matter of time before this kills someone. it is not safe, dealer claims that they can not reproduce, there are no codes. this issue is well documented here and elsewhere, there needs to be a recall. *js.Mileage was 28000 miles. Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in HAMBURG, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Seats

Ford Fusion 2010 Seats Review #10452636

FORD FUSION 2010 car safety problem was reported on Mar 22, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SEATS . head restraint design has the head pushed foward to the point of pain. the head is not in line with with the spine. *tr.Vehicle Identification Number (VIN):3FAHP0JA9AR. Ford Fusion 2010 problem was reported in NEWPORT NEWS, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10452817

FORD FUSION 2010 car safety problem was reported on Jan 25, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . tl* the contact owns a 2010 ford fusion. the contact stated that the vehicle was included in the recall associated with nhtsa campaign id number 11v574000 (wheels:lugs/nuts/bolts). an authorized dealer was contacted on numerous occasions in order to secure an appointment for recall repairs however, the contact was informed that the necessary parts were not yet available to perform the repairs. the manufacturer was also contacted and advised the contact that the parts were still unavailable. the manufacturer was unable to provide a time frame as to when the parts would become available. the failure mileage was 15,000. .0 person(s) were injured. 0 person(s) died.Mileage was 15000 miles. Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in KINGSTON, NH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Service Brakes, Hydraulic

Ford Fusion 2010 Service Brakes, Hydraulic Review #10452828

FORD FUSION 2010 car safety problem was reported on Mar 23, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC . my 2010 ford fusion at 33,000 miles required new rear brakes and rotors, because the brakes were grinding and appeared unsafe. this was not covered by warranty because the calipers were not found to be defective. this appears to be a design flaw that will likely reoccur if not addressed by ford, and could put at risk the safety of myself and my family. *tr.Mileage was 33000 miles. Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in KALAMAZOO, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10452831

FORD FUSION 2010 car safety problem was reported on Dec 23, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i have a 2010 ford fusion s, i was driving home for christmas break when my car shut off and had no throttle response. i didn't drive the vehicle for like five days and the car was fine but it started back up in janurary and again in the beginning of march. it has a code of p211 which is the throttle body issue. i have done some research on the problem and multiple ford fusion's are having the same issues as i am. for some reason ford is trying to avoid hearing the issue on the fact that they have faulty throttle bodies. it is a saftey issue when you are traveling down the highway or interstate at 60-70 mph and all of sudden your car no longer has a throttle response. you have to pull off the road shut your car off and restart it. this doesn't fix the problem it just does it all over again within the next mile or two. ford should realize the issue and make a recall for the throttle body. there are people throughout the united states that are paying between $400-$600 out of their pocket if their car is no longer under warranty to fix a common problem that people are having with ford fusions. *tr.Mileage was 51000 miles. Ford Fusion 2010 problem was reported in ALBANY, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10452831

FORD FUSION 2010 car safety problem was reported on Dec 23, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . i have a 2010 ford fusion s, i was driving home for christmas break when my car shut off and had no throttle response. i didn't drive the vehicle for like five days and the car was fine but it started back up in janurary and again in the beginning of march. it has a code of p211 which is the throttle body issue. i have done some research on the problem and multiple ford fusion's are having the same issues as i am. for some reason ford is trying to avoid hearing the issue on the fact that they have faulty throttle bodies. it is a saftey issue when you are traveling down the highway or interstate at 60-70 mph and all of sudden your car no longer has a throttle response. you have to pull off the road shut your car off and restart it. this doesn't fix the problem it just does it all over again within the next mile or two. ford should realize the issue and make a recall for the throttle body. there are people throughout the united states that are paying between $400-$600 out of their pocket if their car is no longer under warranty to fix a common problem that people are having with ford fusions. *tr.Mileage was 51000 miles. Ford Fusion 2010 problem was reported in ALBANY, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10452876

FORD FUSION 2010 car safety problem was reported on Mar 08, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i was in a parking lot turning into a marked parking space, with my foot off of the accelerator, when the accelerator moved forward abruptly. the engine roared as the car accelerated forward, the car jumped the curb and moved forward striking a column supporting the front corner of an office building. the column fell forward coming to rest on my car, inches above my head. i applied the brakes from the moment i first realized what was taking place, but the brakes had no effect. the cost of repairs to my car was over $3000.00, plus the cost to repair the building. i took the car to the dealership where i had purchased it new. the dealer's employees stated that the computer disclosed no problem. they contacted ford engineers who ordered the dealer not to attempt any repairs. ford claimed no knowledge of such a problem ever occurring. *tr.Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Mileage was 22781 miles. Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in BATON ROUGE, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 5 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10452876

FORD FUSION 2010 car safety problem was reported on Mar 08, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . i was in a parking lot turning into a marked parking space, with my foot off of the accelerator, when the accelerator moved forward abruptly. the engine roared as the car accelerated forward, the car jumped the curb and moved forward striking a column supporting the front corner of an office building. the column fell forward coming to rest on my car, inches above my head. i applied the brakes from the moment i first realized what was taking place, but the brakes had no effect. the cost of repairs to my car was over $3000.00, plus the cost to repair the building. i took the car to the dealership where i had purchased it new. the dealer's employees stated that the computer disclosed no problem. they contacted ford engineers who ordered the dealer not to attempt any repairs. ford claimed no knowledge of such a problem ever occurring. *tr.Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Mileage was 22781 miles. Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in BATON ROUGE, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 5 mph.

Ford Fusion 2010 Engine And Engine Cooling Review #10452984

FORD FUSION 2010 car safety problem was reported on Mar 17, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . the throttle body assembly failed after 70,000 miles. the vehicle would stall at speed, have to be pulled over, stopped, engine turned off and completely restarted. the vehicle had multiple incidences of this nature, and i have been told the problem is a common problem with this year/make/model, that being the throttle body assembly which required replacement. *tr.Mileage was 70000 miles. Vehicle Identification Number (VIN):3FAHP0JG3AR. Ford Fusion 2010 problem was reported in MEBANE, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10452984

FORD FUSION 2010 car safety problem was reported on Mar 17, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . the throttle body assembly failed after 70,000 miles. the vehicle would stall at speed, have to be pulled over, stopped, engine turned off and completely restarted. the vehicle had multiple incidences of this nature, and i have been told the problem is a common problem with this year/make/model, that being the throttle body assembly which required replacement. *tr.Mileage was 70000 miles. Vehicle Identification Number (VIN):3FAHP0JG3AR. Ford Fusion 2010 problem was reported in MEBANE, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Wheels Lugs/nuts/bolts

Ford Fusion 2010 Wheels Lugs/nuts/bolts Review #10453936

FORD FUSION 2010 car safety problem was reported on Jan 18, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS:LUGS/NUTS/BOLTS . tl* the contact owns a 2010 ford fusion. the contact received notification of nhtsa campaign id number: 11v574000 (wheels:lugs/nuts/bolts). the recall was scheduled to begin on or around january 24, 2012 however, the part needed for repairs was unavailable and the vehicle had not been repaired. the dealer was uncertain when the part would become available. the contact planned to notify the manufacturer of the unreasonable time frame in which the recall repair should have been performed. the contact had not experienced a failure. updated 05/11/12 *bf updated 05/21/12.Vehicle Identification Number (VIN):3FAHP0HA2AR. Ford Fusion 2010 problem was reported in GOOSE CREEK, SC. Vehicle was purchased on June 01, 2010. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. DEALER'S NAME: SUMMERVILLE FORD . DEALER'S CITY: SUMMERVILLE . DEALER'S STATE CODE: SC.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10453975

FORD FUSION 2010 car safety problem was reported on Dec 18, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . tl* the contact owns a 2010 ford fusion. while driving approximately 55 mph, the vehicle began to jerk abnormally. the contact applied the accelerator pedal and the engine rpms would increase excessively. the vehicle was taken to the dealer for diagnostic testing. the technicians stated that the transmission would have to be recalibrated. the vehicle was repaired however, the failure persisted. the vehicle was taken back to the dealer where the technicians advised the contact that the transmission would have to be replaced. the vehicle was not repaired. the approximate failure mileage was 200. .0 person(s) were injured. 0 person(s) died.Mileage was 200 miles. Vehicle Identification Number (VIN):3FAHP0HG2AR. Ford Fusion 2010 problem was reported in ALBUQUERQUE, NM. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10454343

FORD FUSION 2010 car safety problem was reported on Feb 29, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . tl* the contact owns a 2010 ford fusion. the contact stated that while driving at various speeds, the vehicle would lose power and fail to accelerate. the vehicle was merged to the shoulder where the maintenance warning light illuminated. the vehicle was taken to the dealer at least three times but they were unable to duplicate the failure. the manufacturer was not notified. the failure mileage was 54,000 and the current mileage was 56,000. .Mileage was 54000 miles. Vehicle Identification Number (VIN):3FAHP0HG0AR. Ford Fusion 2010 problem was reported in BAKERSFIELD, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Engine And Engine Cooling Review #10454782

FORD FUSION 2010 car safety problem was reported on Apr 10, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . while exiting from the expressway on the exit ramp the car suddenly stalled. this was in heavy traffic. i had to try to get the car stopped, put it in park and turn the ignition off and then on again to get it restarted. will take it to be evaluated tomorrow morning. *tr.Mileage was 17000 miles. Vehicle Identification Number (VIN):3FAHP0JGXAR. Ford Fusion 2010 problem was reported in YPSILANTI, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Engine And Engine Cooling Review #10455053

FORD FUSION 2010 car safety problem was reported on Apr 12, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . the vehicle began to jerk when driving or between automatic shifting. specifically when it shifts into third, it jerks extremely hard. the engine and maintenance light will come on as the vehicle stalls. there is no response from the accelerator and i have to put it in park, stop the car and restart it in order for it to move again. i was almost rear ended due to the vehicle dying in the middle of the street. *tr.Mileage was 41000 miles. Ford Fusion 2010 problem was reported in GARLAND, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10455053

FORD FUSION 2010 car safety problem was reported on Apr 12, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . the vehicle began to jerk when driving or between automatic shifting. specifically when it shifts into third, it jerks extremely hard. the engine and maintenance light will come on as the vehicle stalls. there is no response from the accelerator and i have to put it in park, stop the car and restart it in order for it to move again. i was almost rear ended due to the vehicle dying in the middle of the street. *tr.Mileage was 41000 miles. Ford Fusion 2010 problem was reported in GARLAND, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train Review #10455235

FORD FUSION 2010 car safety problem was reported on Mar 29, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i was driving on interstate 65 in the middle lane when the car quit responding. the rpm gauge was stuck on 1 and pressing the accelerator got no response. i was lucky enough to be able to get over and barely off the side of the road but it was a close call. traffic was pretty heavy. i called aaa towing service for help. after 15 minutes i tried to start the car and it started up normally. i was able to get back into traffic and take the next exit. i drove to the dealer. i purchased the car on february 6, 2012 from town & country ford dealer in louisville, ky and had driven it only 596 miles when this happened. the repair bill to replace the throttle body, intake carb kit and recalibrate processor was $730.29. i didn't have the extended warranty so i had to pay the entire cost of the repair. i asked the dealer if this was a problem with the fusion and was told no it was not. *tr.Mileage was 37024 miles. Vehicle Identification Number (VIN):3FAHP0JG1AR. Ford Fusion 2010 problem was reported in LOUISVILLE, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Power Train Review #10455476

FORD FUSION 2010 car safety problem was reported on Mar 08, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . traveling highway, going 70 mph the car suddenly jerks and the speed started to decelerate and the wrench light on dash went on. the engine was still on, but zero ability to accelerate. coasted to the side of the road and the rpm's were fluctuating from 0-1 in park. turned the car off for 10 seconds and turned it back on. after turning the key on, the starter sounded like the key was turned with the engine on for about 20 seconds. the second time was going up hill at 20 mph back roads. same thing with no acceleration and the wrench light came on. had to pull over because the car could not move and shut it off. same with the starter for about 20 seconds of it sounding like the key was turning with engine on after turning it on. incidents are about 1 month and 10 days apart. *js.Mileage was 29900 miles. Vehicle Identification Number (VIN):3FAHP0JG2AR. Ford Fusion 2010 problem was reported in ANTRIM, NH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: BIFUEL. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10455518

FORD FUSION 2010 car safety problem was reported on Dec 05, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . tl* the contact owns a 2010 ford fusion. the contact stated that the vehicle was included in the recall associated with nhtsa campaign id number 11v574000 (wheels:lugs/nuts/bolts). an authorized dealer was notified and the contact was informed that the parts necessary to remedy the recall were not available. the manufacturer was also notified and the contact was informed that the parts were only available on a limited basis. the manufacturer was unable to provide a time frame as to when the parts would become available. the vehicle was not repaired. the failure mileage was 48,000. the vin was unavailable. .Mileage was 48000 miles. Ford Fusion 2010 problem was reported in MIDDLETOWN, DE. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10455590

FORD FUSION 2010 car safety problem was reported on Apr 14, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . i was driving in busy traffic area when my throttle body caused issues on my 2010 ford fusion. i managed to get out of the flow of traffic. my car has only 47,700 miles on it. i have learned other ford fusion owners have experienced the same problem. i managed to get my car home (3 miles away). my son reset the computer, and i drove the car again the following day, and it happened again on the interstate. driving 65 mph in heavy traffic, it happened -- the speed dropped down to 20 mph. i could not go any faster. it was 2 miles until i could get off the next exit ramp. i drove on the shoulder part of the way but there were two cars on the shoulder with other issues that i had to drive around. it was frightening and potentially hazardous. i did not know what the problem was. i did not know if the car was going to die at any time or not. it was dark and late on a sunday. i felt vulnerable. i have read on the internet that other 2010 fusion owners have experienced similar problems - hazardous situations and having to pay for repairs when the car doesn't have high mileage like mine. some are covered under warranty (under 36,000) and some just barely over the 36,000 miles so they were not covered under their warranty. the cost of the repair was just barely under $470. for some reason it wasn't covered under my esp extracare warranty, and i don't get that either. please consider a recall on this part for others who might experience an serious accident as a result. *js.Mileage was 47700 miles. Vehicle Identification Number (VIN):3FAHP0JA9AR. Ford Fusion 2010 problem was reported in MOUNT VERNON, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Fuel System, Gasoline

Ford Fusion 2010 Fuel System, Gasoline Review #10455597

FORD FUSION 2010 car safety problem was reported on Apr 13, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE . i was driving my 2010 ford fusion through rush hour accident traffic. my car began to idle rough and lost power while on a bridge. i was unable to accelerate. i coasted off the bridge and to the emergency lane. i restarted my car and everything seemed okay. i got back into accident traffic. my fusion again began to idle rough. the rpm jumped, my car jerked forwarded and lost power again. i had my car towed to the body shop since it was clearly not safe to drive. the body shop ran tests and said the car was driving fine for them. since picking my car up, it has lost power four times in two days. three of the times happened while on a major interstate! not having the ability to accelerate on a major interstate is a disturbing feeling. my car is back in the shop since it is clearly not safe to drive on a consistent basis. this is not my first issue with the fusion's fuel system. this will be the last ford i own and can't wait to trade it in. *js.Mileage was 68000 miles. Vehicle Identification Number (VIN):3FAHP0HG1AR. Ford Fusion 2010 problem was reported in KIRKWOOD, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: BIFUEL. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10455765

FORD FUSION 2010 car safety problem was reported on Apr 18, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . driving child to school - car's speed starts declining even though accelerator was been pressed (car should have been going between 50 -55 miles). got car off road. switched car off, waited a couple of minutes and then started car again. drove child to school, called ford dealership and placed car in repair shop. was told that warranty went out 4,000 miles ago and part and labor would cost approximately $300.00 and car should be ready to pick up by 5 p.m. next day. got rental car from dealership and was told later same day car went to shop that throttle control will have to be replaced. unfortunately they didn't have one in stock and it would have to be ordered and hopefully with me paying an expedited delivery charge it would be in the next day if not hopefully within the next day day or 2. now i am stuck with a rental car for approximately 3 more days. *js.Mileage was 40000 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in PHILADELPHIA, MS. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10455923

FORD FUSION 2010 car safety problem was reported on Apr 19, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . tl* the contact owns a 2010 ford fusion. the contact stated that while driving 50 mph there was a loss of engine power, but the vehicle did not stall. the vehicle was taken to the dealer, where the contact was informed that the failure could not be duplicated. no repairs were performed on the vehicle. the failure and current mileages were 54,000. .Mileage was 54000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in GREENVILLE, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10455946

FORD FUSION 2010 car safety problem was reported on Apr 19, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . car has 2.5 engine and 6f35 auto transmission. car exhibits "flare" when shifting. typically occurs when cold. problem presented itself at around 42,000 miles. *js.Mileage was 42200 miles. Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in MESA, AZ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10457269

FORD FUSION 2010 car safety problem was reported on Apr 19, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . i was pulling out of my driveway and accelerating, when the car jerked and would not go over 1 mph. the car would not accelerate. it would go in reverse fine. the wrench light illuminated on the dash board. i turned the car off and started it back up a few minutes later and it was running ok. the light went off on the dash. i took it to the dealership and they could not get any codes or duplicate the problem. they suggested changing the throttle body, because they had seen this before on other fusions..0 person(s) were injured. 0 person(s) died.Mileage was 69785 miles. Vehicle Identification Number (VIN):3FAHP0CG8AR. Ford Fusion 2010 problem was reported in WASHIGNTON, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10456328

FORD FUSION 2010 car safety problem was reported on Apr 11, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . the vehicle was bought 3 weeks ago and noticed shifting issues 1 week after purchase. i took the vehicle in to see what was wrong with it and found that the transmission fluid was dark black and had a burnt smell. it appears that there were multiple (updates) needed for transmission??? also was told that is the normal color of the tranny fluid?? burnt black... *tr.Mileage was 38750 miles. Vehicle Identification Number (VIN):3FAHP0HG2AR. Ford Fusion 2010 problem was reported in ROANOKE, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10456758

FORD FUSION 2010 car safety problem was reported on Apr 26, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . was going up a small hill about 30 miles an hour when the car started to lose power. even with hitting the gas all i got was a jerk forward. i made it up the hill lurching forward all the way and got home (only a block). research on the internet indicates this is a known problem with this car that really never gets fixed. what can i do? here are some links to the search sites: http://www.arfc.org/complaints/2010/ford/fusion/ http://forums.automobilemag.com/70/7761889/ford/2010-ford-fusion-transmission/page18.html#ixzz1tlq3uk95. *tr.Mileage was 31000 miles. Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in DULUTH, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Seats

Ford Fusion 2010 Seats Review #10456783

FORD FUSION 2010 car safety problem was reported on Apr 21, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SEATS . we were sitting stopped at a traffic light when a truck struck us from the rear traveling approximately 50mph. the front seats reclined toward the back seats. i noted that there is a current recall posted on your site. i was never made aware of this from ford. i received the car the same month the recall was issued. i am upset that my car has been to ford several times for repairs and another recall but i was not made aware that my car needed this repair. the car was totaled, but fortunately our injuries were limited to bruises. *tr.Vehicle was involved in a crash. Mileage was 80600 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in BIRMINGHAM, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10456811

FORD FUSION 2010 car safety problem was reported on Apr 26, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . the transmission of the 2010 ford fusion slips and resulted in my inability to accelerate the vehicle in heavy traffic while traveling over the george washington bridge in new york city. the dealer, van bortel in rochester, ny, has had the vehicle for a transmission re-build and two additional times for a seal that leaked transmission fluid. i had another incident where i brought the vehicle to another dealer and they replaced additional components pursuant to a program fix from ford (the van bortel should have performed, but did not). this is dangerous as i was lucky not to have been rear-ended by the 18 wheeler behind me at the time my transmission failed on the bridge! *tr.Mileage was 12000 miles. Ford Fusion 2010 problem was reported in CANANDAIGUA, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10456811

FORD FUSION 2010 car safety problem was reported on Apr 26, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . the transmission of the 2010 ford fusion slips and resulted in my inability to accelerate the vehicle in heavy traffic while traveling over the george washington bridge in new york city. the dealer, van bortel in rochester, ny, has had the vehicle for a transmission re-build and two additional times for a seal that leaked transmission fluid. i had another incident where i brought the vehicle to another dealer and they replaced additional components pursuant to a program fix from ford (the van bortel should have performed, but did not). this is dangerous as i was lucky not to have been rear-ended by the 18 wheeler behind me at the time my transmission failed on the bridge! *tr.Mileage was 12000 miles. Ford Fusion 2010 problem was reported in CANANDAIGUA, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10456820

FORD FUSION 2010 car safety problem was reported on Apr 16, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . i was driving down the highway at 70 mph when my car shut off i was almost hit by another car then a semi truck because i didn't know what had happened. my car had no throttle response. after having my car looked at it, it was diagnosed to have a bad throttle body. so i did some research and its a common thong with 2010 ford fusions, but for some reason ford won't either find a way to figure out why they seem to have throttle bodies that are malfunctioning and putting their drivers lives in danger. they need to recall this before it causes someone to lose their life. for people who don't know it cost about $500 to get it fixed if your vehicle isn't under warranty. *tr.Mileage was 52956 miles. Ford Fusion 2010 problem was reported in ALBANY, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Fuel System, Gasoline

Ford Fusion 2010 Fuel System, Gasoline Review #10456820

FORD FUSION 2010 car safety problem was reported on Apr 16, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE . i was driving down the highway at 70 mph when my car shut off i was almost hit by another car then a semi truck because i didn't know what had happened. my car had no throttle response. after having my car looked at it, it was diagnosed to have a bad throttle body. so i did some research and its a common thong with 2010 ford fusions, but for some reason ford won't either find a way to figure out why they seem to have throttle bodies that are malfunctioning and putting their drivers lives in danger. they need to recall this before it causes someone to lose their life. for people who don't know it cost about $500 to get it fixed if your vehicle isn't under warranty. *tr.Mileage was 52956 miles. Ford Fusion 2010 problem was reported in ALBANY, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10456820

FORD FUSION 2010 car safety problem was reported on Apr 16, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i was driving down the highway at 70 mph when my car shut off i was almost hit by another car then a semi truck because i didn't know what had happened. my car had no throttle response. after having my car looked at it, it was diagnosed to have a bad throttle body. so i did some research and its a common thong with 2010 ford fusions, but for some reason ford won't either find a way to figure out why they seem to have throttle bodies that are malfunctioning and putting their drivers lives in danger. they need to recall this before it causes someone to lose their life. for people who don't know it cost about $500 to get it fixed if your vehicle isn't under warranty. *tr.Mileage was 52956 miles. Ford Fusion 2010 problem was reported in ALBANY, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10456833

FORD FUSION 2010 car safety problem was reported on Apr 30, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . i was going down the highway at 55 mph car started to run rough then lost all power. i was able to get over to the side of the road. at place on the highway where car stop running there was no breakdown lane. turned engine off waited a minute attempted to restart car it was still running rough and would not accelerate also wrench light came on. shut car off waited a couple of more minutes car started and accelerated but now the check engine light came on. this is not the first time the car lost power but when i call service they said it was nothing just a computer glitch. the first time the car lost power i was able to turn it off and back on with no problems. *js.Mileage was 26554 miles. Vehicle Identification Number (VIN):3FAHP0JA2AR. Ford Fusion 2010 problem was reported in DORCHESTER, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Engine And Engine Cooling Review #10457089

FORD FUSION 2010 car safety problem was reported on May 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . 2010 ford fusion car stalled and engine shut off in heavy traffic 2 mths ago. had to pull over. cranked it was fine. days later, engine begins to crank every few days, slow at first but will start. been going on since. 3 wks today, car powers down while driving 65 mph this morning on main int. hwy.the wrench light came on dashboard. car would not accelerate when i pressed the gas peddle. had to "coast" to er lane. car was running, but could not accelerate at all. when stopped, turned car off. recranked engine. wrench light went off, and drove to work fine. took to dealer today. while explaining the issue, an employee overheard and said "do you drive a fusion?" i said yes, he said its your throttle body. he says this without even looking at the car! confirmed it was throttle body part after inspection. part was not in stock. told i could drive car home. they would call when part comes in. dealer called this evening and said my manf. warranty was past time, and additional warranty tech would not cover throttle body part. part expense $261 plus taxes and 30 minutes labor time to install. i'm disturbed to know ford is aware and others are having this problem and i am extremely scared to drive this car knowing it stalled at 65 miles an hour!!! someone needs to pull these cars off the road and make the repairs to these vehicles. i have never owned an american made car. this is my first one. some first impression. i will be trading this car as soon as i can. i am just so disappointed in ford claiming the "built ford tough" motto. this isn't tough, its dangerous! i've never owned a car where being less than 2yrs old, a part already has to be replaced? seriously?? ford should pay attention to their complaints. how many complaints does it take to get a recall??????????? mine makes number 320........ a recall should be after 2 people are claiming the same thing. *js.Mileage was 51342 miles. Vehicle Identification Number (VIN):3FAHP0JG3AR. Ford Fusion 2010 problem was reported in DOUGLASVILLE, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: BIFUEL. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10457089

FORD FUSION 2010 car safety problem was reported on May 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . 2010 ford fusion car stalled and engine shut off in heavy traffic 2 mths ago. had to pull over. cranked it was fine. days later, engine begins to crank every few days, slow at first but will start. been going on since. 3 wks today, car powers down while driving 65 mph this morning on main int. hwy.the wrench light came on dashboard. car would not accelerate when i pressed the gas peddle. had to "coast" to er lane. car was running, but could not accelerate at all. when stopped, turned car off. recranked engine. wrench light went off, and drove to work fine. took to dealer today. while explaining the issue, an employee overheard and said "do you drive a fusion?" i said yes, he said its your throttle body. he says this without even looking at the car! confirmed it was throttle body part after inspection. part was not in stock. told i could drive car home. they would call when part comes in. dealer called this evening and said my manf. warranty was past time, and additional warranty tech would not cover throttle body part. part expense $261 plus taxes and 30 minutes labor time to install. i'm disturbed to know ford is aware and others are having this problem and i am extremely scared to drive this car knowing it stalled at 65 miles an hour!!! someone needs to pull these cars off the road and make the repairs to these vehicles. i have never owned an american made car. this is my first one. some first impression. i will be trading this car as soon as i can. i am just so disappointed in ford claiming the "built ford tough" motto. this isn't tough, its dangerous! i've never owned a car where being less than 2yrs old, a part already has to be replaced? seriously?? ford should pay attention to their complaints. how many complaints does it take to get a recall??????????? mine makes number 320........ a recall should be after 2 people are claiming the same thing. *js.Mileage was 51342 miles. Vehicle Identification Number (VIN):3FAHP0JG3AR. Ford Fusion 2010 problem was reported in DOUGLASVILLE, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: BIFUEL. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Fuel System, Gasoline

Ford Fusion 2010 Fuel System, Gasoline Review #10457662

FORD FUSION 2010 car safety problem was reported on May 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE . i am guessing at the "component selection" above. i was driving 30 mph in a neighborhood; car pitched or lunged forward; wrench light came on panel; rpm's dropped; car slowed down and pressing gas pedal did no good; car was still running; car coasted to a stop. waited for help to come. restarted car, it went about 1/2 mile and did the same thing; took to dealership. they checked it out and could not replicate the problem and returned it to me; within ten minutes and 5 miles, it happened again in the same sequence as described above except i was going 50 mph on a busy hilly two lane state highway. took it back to dealership they said it was the throttle body or throttle rail. i am scared to drive it once, or if, it is repaired; still haven't received car back and parts on back order! internet search lead me to numerous occurrences exactly like mine and some were temporary fix that led to other problems with the throttle and transmission. *tr.Mileage was 29723 miles. Vehicle Identification Number (VIN):3FAHP0JG4AR. Ford Fusion 2010 problem was reported in ATMORE, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Service Brakes, Hydraulic

Ford Fusion 2010 Service Brakes, Hydraulic Review #10457720

FORD FUSION 2010 car safety problem was reported on Apr 02, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC . extreme over heating of left (drivers side) rear brakes leading to premature and uneven pad failure. pads appear to have become so hot that there is ash present on them. *tr.Mileage was 19500 miles. Vehicle Identification Number (VIN):3FAHP0JA8AR. Ford Fusion 2010 problem was reported in ROYAL OAK, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10457721

FORD FUSION 2010 car safety problem was reported on May 05, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while driving on the interstate, the wrench light came on and the car became unresponsive to acceleration. i had to turn on the hazards and coast to the shoulder. the car was able to be restarted and drove fine for another 30 minutes before the same thing happened again. 2 days later the same thing happened on the interstate again, requiring me to coast to the shoulder of the road! today it happened while i was only going 45 mph and happened three times in 10 miles. when i got home i immediately began researching other ford fusion problems and found this to be a common occurrence. we tested the chip of the car and got a code of p2112, indicating the throttle body was malfunctioning. this comes behind an electrical problem requiring a new battery after 50,000 miles, a plastic piece breaking off the sunroof and needing to be replaced at 40,000 miles, and the sunglasses spring breaking at 35,000 miles! this is the second ford i have owned and we were thrilled with our ford five hundred, but the fusion seems to have more problems than it has good qualities! ford really needs to find a fix for their throttle problem before one of us is injured or killed while we coast to safety on the interstate in a malfunctioning car! *tr.Mileage was 72000 miles. Ford Fusion 2010 problem was reported in COLUMBIA, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Fuel System, Gasoline

Ford Fusion 2010 Fuel System, Gasoline Review #10457721

FORD FUSION 2010 car safety problem was reported on May 05, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE . while driving on the interstate, the wrench light came on and the car became unresponsive to acceleration. i had to turn on the hazards and coast to the shoulder. the car was able to be restarted and drove fine for another 30 minutes before the same thing happened again. 2 days later the same thing happened on the interstate again, requiring me to coast to the shoulder of the road! today it happened while i was only going 45 mph and happened three times in 10 miles. when i got home i immediately began researching other ford fusion problems and found this to be a common occurrence. we tested the chip of the car and got a code of p2112, indicating the throttle body was malfunctioning. this comes behind an electrical problem requiring a new battery after 50,000 miles, a plastic piece breaking off the sunroof and needing to be replaced at 40,000 miles, and the sunglasses spring breaking at 35,000 miles! this is the second ford i have owned and we were thrilled with our ford five hundred, but the fusion seems to have more problems than it has good qualities! ford really needs to find a fix for their throttle problem before one of us is injured or killed while we coast to safety on the interstate in a malfunctioning car! *tr.Mileage was 72000 miles. Ford Fusion 2010 problem was reported in COLUMBIA, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Tires

Ford Fusion 2010 Tires Review #10457771

FORD FUSION 2010 car safety problem was reported on May 07, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with TIRES . tl* the contact owns michelin energy saver tires, size p225/50/r17, that were equipped on a 2010 ford fusion. while examining the tires, the contact noticed that all four tires were experiencing dry rot around the sidewall. the tires had not been diagnosed or repaired. the current and failure mielages were 28,000. .Mileage was 28000 miles. Ford Fusion 2010 problem was reported in BALTIMORE, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10457958

FORD FUSION 2010 car safety problem was reported on May 02, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . 2010 ford fusion: while driving at 65mph on a highway with cruise control set the car lost power and stalled. tachometer dropped to 1000 rpms and fluctuated between 500 - 1000 rpms. wrench light (throttle / transmission) illuminated and the car coasted to a crawl at less than 5mph. the car's throttle was unresponsive and i was unable to accelerate. i became a serious rear-end hazard in a construction zone and had to pull off to the side of the road. i put the car in park, restarted it and the car ran fine. i am just barely under warranty (and just bought the car 1 week ago) so i brought it to a ford dealer - they "checked" the car and found "nothing wrong" with their computer scan and stated that there was no error code - so there was nothing that they could do. the day after i picked the car up from the dealer the car did the same thing, twice. this time it did it after a cold start in the morning and again when i left work in the afternoon - again the wrench light came on and shut off once i restarted the car. bringing the car in tomorrow again...we'll see what happens. what a safety risk - my wife refuses to drive the car! *tr.Mileage was 35000 miles. Ford Fusion 2010 problem was reported in SCHOFIELD, WI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10457958

FORD FUSION 2010 car safety problem was reported on May 02, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . 2010 ford fusion: while driving at 65mph on a highway with cruise control set the car lost power and stalled. tachometer dropped to 1000 rpms and fluctuated between 500 - 1000 rpms. wrench light (throttle / transmission) illuminated and the car coasted to a crawl at less than 5mph. the car's throttle was unresponsive and i was unable to accelerate. i became a serious rear-end hazard in a construction zone and had to pull off to the side of the road. i put the car in park, restarted it and the car ran fine. i am just barely under warranty (and just bought the car 1 week ago) so i brought it to a ford dealer - they "checked" the car and found "nothing wrong" with their computer scan and stated that there was no error code - so there was nothing that they could do. the day after i picked the car up from the dealer the car did the same thing, twice. this time it did it after a cold start in the morning and again when i left work in the afternoon - again the wrench light came on and shut off once i restarted the car. bringing the car in tomorrow again...we'll see what happens. what a safety risk - my wife refuses to drive the car! *tr.Mileage was 35000 miles. Ford Fusion 2010 problem was reported in SCHOFIELD, WI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Engine And Engine Cooling Review #10458008

FORD FUSION 2010 car safety problem was reported on Mar 10, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . tl* the contact owns a 2010 ford fusion. the contact was driving 60 mph when the vehicle began to decelerate independently. the contact shut off the vehicle, and the vehicle regained normal operation once restarted. the contact stated that the failure was recurring and would be experienced several times throughout any given day. the vehicle was taken to the dealer who advised that the mass air flow sensor needed to be replaced. the repair was performed but did not permanently correct the failure. the manufacturer was notified who advised the contact that there were no recalls and offered no assistance. the failure mileage was 47,000. .Mileage was 47000 miles. Vehicle Identification Number (VIN):3FAHP0JG5AR. Ford Fusion 2010 problem was reported in ALBANY, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10458110

FORD FUSION 2010 car safety problem was reported on May 10, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i was driving home and going up a hill when i felt the vehicle slow acceleration and then it revved back up. the transmission/throttle control light came on so i pulled over. i turned the vehicle off and waited for a few minutes. turned the vehicle back on and when i went to accelerate it lurched. i continued driving home and since it was after 9:00 p.m. when i got home, i couldn't take it to the dealership until the next morning. on may 11, 2012 i took it to the dealership and they called to tell me that the vehicle slipped from 4th gear into 5th gear and this should never happen so they were going to have to pull the transmission and i would be without my car for 5-6 days. after research on the internet it appears that several people are having this same issue with the transmission of the 2010 ford fusion. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 26572 miles. Vehicle Identification Number (VIN):3FAHPOJG8AR. Ford Fusion 2010 problem was reported in OZARK, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Power Train Review #10458254

FORD FUSION 2010 car safety problem was reported on May 12, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . on 5/12/12 coming home from a softball tournament with the cruise on at around 65 mph the yellow wrench light came on. engine was still running but could not accelerate. coasted into a church parking lot. put the car in park and restarted. when restarting seemed hard to start...like an alternator issue. arrived home safely (was about 5 miles from home when incident happened). on 5/13/12 (sunday) same issue except it happened 3 times during a 30 mile trip. the last time i had pulled over and put it into park i was worried it wouldn't start...turned and turned but slowly...again sounded like an alternator. i had issues with the cruise control a few months back and of course nothing was found to be wrong. short story is when i hit "resume" to get it back to the speed it was while on cruise control the rpm's will run 5000-6000 for f a r longer than it should. the car will be to the desired speed and it will stay at the high rpm for 4-6 seconds instead of kicking into the next gear which obviously is hard on the engine and gas mileage. not happy with the dealership in their investigation of matters and not happy with the car itself. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 34000 miles. Ford Fusion 2010 problem was reported in MURPHY, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10458254

FORD FUSION 2010 car safety problem was reported on May 12, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . on 5/12/12 coming home from a softball tournament with the cruise on at around 65 mph the yellow wrench light came on. engine was still running but could not accelerate. coasted into a church parking lot. put the car in park and restarted. when restarting seemed hard to start...like an alternator issue. arrived home safely (was about 5 miles from home when incident happened). on 5/13/12 (sunday) same issue except it happened 3 times during a 30 mile trip. the last time i had pulled over and put it into park i was worried it wouldn't start...turned and turned but slowly...again sounded like an alternator. i had issues with the cruise control a few months back and of course nothing was found to be wrong. short story is when i hit "resume" to get it back to the speed it was while on cruise control the rpm's will run 5000-6000 for f a r longer than it should. the car will be to the desired speed and it will stay at the high rpm for 4-6 seconds instead of kicking into the next gear which obviously is hard on the engine and gas mileage. not happy with the dealership in their investigation of matters and not happy with the car itself. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 34000 miles. Ford Fusion 2010 problem was reported in MURPHY, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10458277

FORD FUSION 2010 car safety problem was reported on July 26, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . driving on the west virginia turnpike at 65-70 mph when the rpm's jumped above 4 and lost all power to the engine. the engine was still running but had no power from the gas pedal to the engine. pulled to the far right side of the road as i was going up hill into the truck lane and then eventually on to the berm as the trucks were now running faster than me going uphill. it was the most dangerous driving situation i have ever been through. i was able to locate a ford dealership on the turnpike where i could leave the car for the necessary repairs. the repairs took a total of 25 days. ford would not provide me with a loaner car as i bought the vehicle used and therefore no rental coverage even though the issue was a known issue due to faulty parts and a poor initial repair by ford. i had to rent a vehicle in west virginia in order to complete my drive home and had to drop the rental in columbus. $185 + gas + deposit and resulting nsf fees in my checking account for a 12 hour car rental that ford would not cover. upon getting my vehicle back it ran smoothly until october of the same year. i took my vehicle to a national chain oil change company who advised that they could see transaxle fluid all the way to the back of the underbody of the vehicle. i took the car to my local ford dealership who found that the repair completed in west virginia did not get the pan sealed properly and the fluid was leaking from the faulty seal, which they repaired but it took them 14 days to do so. fast forward to may and another hard shift with a lurch forward and then no power from the gas pedal to the engine. took it to the local dealership who could find no error codes and could not duplicate the issue. 5/13 - mother's day and it happens again but this time the engine light is now on and the car runs rough. taking to dealership again tomorrow. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 39000 miles. Vehicle Identification Number (VIN):3FAHP0JG6AR. Ford Fusion 2010 problem was reported in COLUMBUS, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10458639

FORD FUSION 2010 car safety problem was reported on Mar 30, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact stated that while driving approximately 50 mph, there was a complete loss of the engine power and the vehicle stalled. the contact was able to maneuver to the side of the road, where the engine was turned off and then restarted. the vehicle resumed as normal. the failure occurred five times. the vehicle was taken to an authorized dealer on three different occasions for diagnosis. the third time a trouble code was detected and the throttle body was replaced. the manufacturer was notified of the failure. the approximate failure mileage was 43,000. .0 person(s) were injured. 0 person(s) died.Mileage was 43000 miles. Vehicle Identification Number (VIN):3FAHP0JG3AR. Ford Fusion 2010 problem was reported in FROSTBURG, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Tires

Ford Fusion 2010 Tires Review #10458840

FORD FUSION 2010 car safety problem was reported on May 02, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with TIRES . tl* the contact owns a 2010 ford fusion equipped with michelin hydro-edge tires, size 215/60/r16. the dot number was apxn4xx0110. the contact stated that the sidewalls of all four tires were cracked. the vehicle was taken to an authorized dealer for routine maintenance when the failure was diagnosed. the manufacturer was notified and the contact was awiating a reply. the failure mileage on the tires was 17,000. the failure mileage of the vehicle was 35,100. the vin was unavailable. updated 7/23/12 *cn michelin refused to adjust the defective tires under workmanship and material warranty. they referred to defect as cosmetic cracking.0 person(s) were injured. 0 person(s) died.Mileage was 35100 miles. Ford Fusion 2010 problem was reported in REDLANDS, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Structure Body Door

Ford Fusion 2010 Structure Body Door Review #10459021

FORD FUSION 2010 car safety problem was reported on Apr 01, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE:BODY:DOOR . driver side interior door handle plastic separated and handle cracked. unable to lock door without having to hold handle in. was able to open door from the interior with great caution. handle continued to crack all the way through and had to be replaced. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Ford Fusion 2010 problem was reported in STOCKTON, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10459098

FORD FUSION 2010 car safety problem was reported on Apr 13, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i drive approximately 30 miles on the highway to get to work. the day this problem first occurred, i got off the highway and came to a stop sign. i checked for traffic both directions. a car was coming from the left, and i was turning right. i knew with my car's acceleration i had plenty of space to pull out safely (it has a v6 engine, automatic transmission). i hit the gas and pulled out. the car did not accelerate as expected. i barely hit 5 mph and the tachometer redlined. i took my foot off the gas pedal and tried again. same thing - redlined. the third time i tried, the car shuddered and finally shifted to the next gear. the car behind me was far enough away to slow down safely, but in a different situation they could have easily hit me. i just rolled out in front of them because the car didn't respond when i hit the gas. immediately after that incident, i scheduled a service appointment at a ford dealership. the first available appointment was two weeks out. i booked the appointment and continued to (cautiously) drive my car to work. the car ran rough even at constant highway speeds. last night i dropped my car off at the dealership for the service appointment. i took the highway to get there. when i tried to accelerate to merge onto the highway, the problem occurred again. i rolled out into traffic at about 5 mph, hitting the gas pedal and getting nothing. again, i was lucky that there was enough room between me and the approaching traffic. this problem could have easily caused a bad accident. my car is currently at the ford dealership. i'm waiting for them to call back with a diagnosis. *tt.0 person(s) were injured. 0 person(s) died.Mileage was 35500 miles. Vehicle Identification Number (VIN):3FAHP0JG3AR. Ford Fusion 2010 problem was reported in PITTSBURGH, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 5 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10459098

FORD FUSION 2010 car safety problem was reported on Apr 13, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . i drive approximately 30 miles on the highway to get to work. the day this problem first occurred, i got off the highway and came to a stop sign. i checked for traffic both directions. a car was coming from the left, and i was turning right. i knew with my car's acceleration i had plenty of space to pull out safely (it has a v6 engine, automatic transmission). i hit the gas and pulled out. the car did not accelerate as expected. i barely hit 5 mph and the tachometer redlined. i took my foot off the gas pedal and tried again. same thing - redlined. the third time i tried, the car shuddered and finally shifted to the next gear. the car behind me was far enough away to slow down safely, but in a different situation they could have easily hit me. i just rolled out in front of them because the car didn't respond when i hit the gas. immediately after that incident, i scheduled a service appointment at a ford dealership. the first available appointment was two weeks out. i booked the appointment and continued to (cautiously) drive my car to work. the car ran rough even at constant highway speeds. last night i dropped my car off at the dealership for the service appointment. i took the highway to get there. when i tried to accelerate to merge onto the highway, the problem occurred again. i rolled out into traffic at about 5 mph, hitting the gas pedal and getting nothing. again, i was lucky that there was enough room between me and the approaching traffic. this problem could have easily caused a bad accident. my car is currently at the ford dealership. i'm waiting for them to call back with a diagnosis. *tt.0 person(s) were injured. 0 person(s) died.Mileage was 35500 miles. Vehicle Identification Number (VIN):3FAHP0JG3AR. Ford Fusion 2010 problem was reported in PITTSBURGH, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 5 mph.

Ford Fusion 2010 Service Brakes

Ford Fusion 2010 Service Brakes Review #10459278

FORD FUSION 2010 car safety problem was reported on Mar 31, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES . at 2000 miles had car back for brakes.its been back 8 times. they have cut the rotors and replaced pads and still jumps after about 5000 miles. vibration in car that they couldnt find y. replaced trottle body . there is an issue with the brakes they need to find out whats wrong. they have cut the rotors down to the point they replaced them and the ones on the front arent 6 months old and they cut them again. *tt.0 person(s) were injured. 0 person(s) died.Mileage was 2000 miles. Vehicle Identification Number (VIN):3FAHP0DC1AR. Ford Fusion 2010 problem was reported in NICHOLSON, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:AWD. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10459278

FORD FUSION 2010 car safety problem was reported on Mar 31, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . at 2000 miles had car back for brakes.its been back 8 times. they have cut the rotors and replaced pads and still jumps after about 5000 miles. vibration in car that they couldnt find y. replaced trottle body . there is an issue with the brakes they need to find out whats wrong. they have cut the rotors down to the point they replaced them and the ones on the front arent 6 months old and they cut them again. *tt.0 person(s) were injured. 0 person(s) died.Mileage was 2000 miles. Vehicle Identification Number (VIN):3FAHP0DC1AR. Ford Fusion 2010 problem was reported in NICHOLSON, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:AWD. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10459278

FORD FUSION 2010 car safety problem was reported on Mar 31, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . at 2000 miles had car back for brakes.its been back 8 times. they have cut the rotors and replaced pads and still jumps after about 5000 miles. vibration in car that they couldnt find y. replaced trottle body . there is an issue with the brakes they need to find out whats wrong. they have cut the rotors down to the point they replaced them and the ones on the front arent 6 months old and they cut them again. *tt.0 person(s) were injured. 0 person(s) died.Mileage was 2000 miles. Vehicle Identification Number (VIN):3FAHP0DC1AR. Ford Fusion 2010 problem was reported in NICHOLSON, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:AWD. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10459688

FORD FUSION 2010 car safety problem was reported on May 02, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while driving my car suddenly went into shut down mode. a wrench symbol showed on panel. i was able to turn into a drive way and after turning the vehicle off and back on the wrench went off and the car ran normal. i took to the shop and nothing showed on the computer. it then happened 5 more times. back to the dealership now says that it is bad throttle body and is not covered. after researching online it appears to be a bigger problem and ford should recall. there are so many complaints that it is obvious that it is a defect. people are going to get killed. ford fix this now. i have no choice but to pay to have it fixed but i shouldn't. it would be very interesting to see how many have been fixed to date just by ford and not other companies. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 36000 miles. Ford Fusion 2010 problem was reported in DENHAM SPRINGS, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Power Train Review #10459708

FORD FUSION 2010 car safety problem was reported on May 07, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . when trying to accelerate, rpms would rev to between 4000-5000 but car would not speed up. once it finally started (after three tries), car finally jerked forward and shuddered before speeding up. after driving for about 30 minutes, i then tried to reverse the car and it jerked and grinded extremely hard. smells like something is burning at times. took to dealership twice already, but still having problems. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 33740 miles. Ford Fusion 2010 problem was reported in RAYMORE, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10459847

FORD FUSION 2010 car safety problem was reported on May 23, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . tl* the contact owns a 2010 ford fusion. the contact was driving 35 mph when the vehicle stalled without warning. the failure was recurring. the contact would wait a few minutes to restart the engine without any problems. the vehicle was taken to the dealer who ran a diagnostic test and informed her that the electronic throttle body needed to be replaced. the manufacturer was not notified of the failure. the failure mileage was 60,241. .0 person(s) were injured. 0 person(s) died.Mileage was 60241 miles. Vehicle Identification Number (VIN):3FA8P0HA5AR. Ford Fusion 2010 problem was reported in SAVANNAH, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10459890

FORD FUSION 2010 car safety problem was reported on Mar 15, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . tl* the contact owns a 2010 ford fusion. while stopped at a traffic stop, the vehicle suddenly stalled without warning. the vehicle was taken to the dealer for diagnostics. the technician advised the contact that the fuel valve would have to be replaced. the vehicle was repaired however, the failure persisted. there were no further repairs performed. the approximate failure mileage was 20,000. .0 person(s) were injured. 0 person(s) died.Mileage was 20000 miles. Vehicle Identification Number (VIN):3FAHP0HG0AR. Ford Fusion 2010 problem was reported in MANCHESTER, CT. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Fuel/propulsion System Review #10459974

FORD FUSION 2010 car safety problem was reported on May 24, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . i have a 2010 ford fusion and my car stopped on me. i was driving on i-30 in dallas texas and the wrench symbol and the battery light came on. i took my car to machaik ford in desoto, texas and i was informed that the throttle was bad and that it would cost $542.00 dollars. why want ford help me and all the other drives that are having this issue. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 43184 miles. Ford Fusion 2010 problem was reported in CEDAR HILL, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10460019

FORD FUSION 2010 car safety problem was reported on May 27, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . going about 75 mph with cruise on when problem occurred. the wrench light comes on and the car loses its acceleration completely. i pull over the side of the road. the engine would only turn 1000 rpm. the only way to fix it is to turn the car off and back on again. the wrench light will disappear after that and it'll start driving normally again. the problems seems to be with a bad throttle body assembly part. contacted ford about safety problem. many examples on the internet of other owners with this problem with the 2010 ford fusion. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 39000 miles. Vehicle Identification Number (VIN):3FAHP0JG5AR. Ford Fusion 2010 problem was reported in NEW BRAUNFELS, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 75 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10460019

FORD FUSION 2010 car safety problem was reported on May 27, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . going about 75 mph with cruise on when problem occurred. the wrench light comes on and the car loses its acceleration completely. i pull over the side of the road. the engine would only turn 1000 rpm. the only way to fix it is to turn the car off and back on again. the wrench light will disappear after that and it'll start driving normally again. the problems seems to be with a bad throttle body assembly part. contacted ford about safety problem. many examples on the internet of other owners with this problem with the 2010 ford fusion. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 39000 miles. Vehicle Identification Number (VIN):3FAHP0JG5AR. Ford Fusion 2010 problem was reported in NEW BRAUNFELS, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 75 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10460019

FORD FUSION 2010 car safety problem was reported on May 27, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . going about 75 mph with cruise on when problem occurred. the wrench light comes on and the car loses its acceleration completely. i pull over the side of the road. the engine would only turn 1000 rpm. the only way to fix it is to turn the car off and back on again. the wrench light will disappear after that and it'll start driving normally again. the problems seems to be with a bad throttle body assembly part. contacted ford about safety problem. many examples on the internet of other owners with this problem with the 2010 ford fusion. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 39000 miles. Vehicle Identification Number (VIN):3FAHP0JG5AR. Ford Fusion 2010 problem was reported in NEW BRAUNFELS, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 75 mph.

Ford Fusion 2010 Engine Review #10460102

FORD FUSION 2010 car safety problem was reported on May 29, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . making a left hand turn from a complete stop onto a busy avenue when the "wrench light" on the dash light up, the car started to shudder & could not accelerate, and had to pull over to the side of the road. turned car off and back on and it happened again within 1 mile. drove to the home of a friend and had him go with me to try and figure out what was wrong. car shook hard and nearly died when coming to a stop sign. after doing a google search of the problem i found it to be a very widespread problem and many times at 70 mph in heavy traffic even on new cars with as few as 1300 miles on them. this is very dangerous and only a matter of time before somebody dies. in many cases rather than losing the ability to accelerate, the opposite will happen and the car goes full throttle forward! there is an avalanche of documentation on this problem and ford refuses to do a safety recall. the nhtsa's sole reason to exist in the first place is safety and this is clearly unsafe. rest assured that if the nhtsa does not force ford to do a recall people will die. as for myself and several others i have been in contact with, we will be filing a lawsuit against ford for their negligence and the nhtsa for failing to act despite the large volume of readily accessible information regarding this very serious safety issue. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 54061 miles. Vehicle Identification Number (VIN):3FAHP0HAXAR. Ford Fusion 2010 problem was reported in VENTURA, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10460102

FORD FUSION 2010 car safety problem was reported on May 29, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . making a left hand turn from a complete stop onto a busy avenue when the "wrench light" on the dash light up, the car started to shudder & could not accelerate, and had to pull over to the side of the road. turned car off and back on and it happened again within 1 mile. drove to the home of a friend and had him go with me to try and figure out what was wrong. car shook hard and nearly died when coming to a stop sign. after doing a google search of the problem i found it to be a very widespread problem and many times at 70 mph in heavy traffic even on new cars with as few as 1300 miles on them. this is very dangerous and only a matter of time before somebody dies. in many cases rather than losing the ability to accelerate, the opposite will happen and the car goes full throttle forward! there is an avalanche of documentation on this problem and ford refuses to do a safety recall. the nhtsa's sole reason to exist in the first place is safety and this is clearly unsafe. rest assured that if the nhtsa does not force ford to do a recall people will die. as for myself and several others i have been in contact with, we will be filing a lawsuit against ford for their negligence and the nhtsa for failing to act despite the large volume of readily accessible information regarding this very serious safety issue. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 54061 miles. Vehicle Identification Number (VIN):3FAHP0HAXAR. Ford Fusion 2010 problem was reported in VENTURA, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10460117

FORD FUSION 2010 car safety problem was reported on May 14, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . tl* the contact owns a 2010 ford fusion. the contact was traveling 70 mph when the vehicle stalled. the contact safely maneuvered to the shoulder and stopped the vehicle. the check engine light illuminated during the failure. the contact was able to successfully restart the vehicle and continue driving. the failure recurred intermittently. the vehicle was taken to an authorized dealer where they were unable to diagnose the failure. the vehicle was not repaired. the manufacturer was not made aware of the failure. the failure mileage was 55,000. .0 person(s) were injured. 0 person(s) died.Mileage was 55000 miles. Vehicle Identification Number (VIN):3FAHP0JA6AR. Ford Fusion 2010 problem was reported in LOGANVILLE, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Engine Review #10460210

FORD FUSION 2010 car safety problem was reported on May 31, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . while accelerating from a stop the engine suddenly cut out and began a rough idle. the check engine light and the wrench light came on. the engine would not rev even with the gas pedal pushed in. coasted to a stop. turned the ignition off and then restarted the car. the check engine light and wrench light were no longer lit. started to accelerate away and then it happened again with the check engine light and wrench light on. i was able to idle home. once at home i turned the ignition off and started it back up. this time the check engine light came on but not the wrench. while in park i would rev the engine and it sounded fine and could not get the engine to shut down while revving. i didn't move the car and had it towed. fortunately it has only 32707 miles on it and covered by warranty. so, will have to wait to find out what the cause is. based on other complaints and their follow-up it sounds like the throttle body issue. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 32707 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in BATON ROUGE, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10460210

FORD FUSION 2010 car safety problem was reported on May 31, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while accelerating from a stop the engine suddenly cut out and began a rough idle. the check engine light and the wrench light came on. the engine would not rev even with the gas pedal pushed in. coasted to a stop. turned the ignition off and then restarted the car. the check engine light and wrench light were no longer lit. started to accelerate away and then it happened again with the check engine light and wrench light on. i was able to idle home. once at home i turned the ignition off and started it back up. this time the check engine light came on but not the wrench. while in park i would rev the engine and it sounded fine and could not get the engine to shut down while revving. i didn't move the car and had it towed. fortunately it has only 32707 miles on it and covered by warranty. so, will have to wait to find out what the cause is. based on other complaints and their follow-up it sounds like the throttle body issue. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 32707 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in BATON ROUGE, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Steering

Ford Fusion 2010 Steering Review #10460240

FORD FUSION 2010 car safety problem was reported on June 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with STEERING . upon starting my car in my driveway, a message appeared across the dashboard reading "power steering assist fault" also "service advance trac". i bought this car not even 8 months ago, the mileage being over what a warranty could cover. twice i was turned away because the vehicle being too "new" the coding could not be detected, reading there was nothing wrong. clearly with no power steering, and the messages going off...there was something wrong. this is not the first of this exact same complaint i have found online regarding the same year, make and model of this vehicle. it is now sitting at a garage and i am waiting on the verdict. not to mention i have to pay just to have it diagnosed, i am being told if similar to other problems that sound like this one, i could be looking at anywhere from $800-1500 + for this to be solved. why will ford not come out with a recall by now, after all of the similar complaints!? i have always been partial to ford's and now regret ever making the purchase. please help out your customers ford! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 95000 miles. Ford Fusion 2010 problem was reported in RICHLAND, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10460341

FORD FUSION 2010 car safety problem was reported on Apr 25, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . i have a 2010 ford fusion with a four cylinder engine. while driving to work, i started speeding up from an intersection, only to experience a complete and total loss of power, the wrench light came, the engine started misfiring (rough idle at less than 550 rpm), but all systems where still working. pressing the gas pedal produced no results. i was able to pull off the side of the road, stop the engine, let the car sit for about 15 seconds, and then restarted it. when the engine restarted, the car started up and ran like nothing had happened. yesterday (june 1st), the fusion did the exact same thing, except this time i was pulling into an intersection (approximately 5 miles per hour). i had a catastrophic loss of power, the wrench light came on again, the engine was misfiring (rough idle), the rest of the systems continued working. luckily no one was coming in my direction and i was able to pull off the road into a parking lot, stop the car, and then restart it. i took it to the dealer today and they diagnosed it as needing a new throttle body. they quoted the price and labor at $400 for the repair. i've had this car less than 1 year and it only has 49,800 miles on it. if i had been pulling onto a busy street and experienced the same loss of power, it could have been a much more dangerous situation. according to my research, this is a common problem with the 2010 ford fusion, and the replacement part has been "redesigned" according to the dealer where i took my car for repair. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 47282 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in LEXINGTON, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10460341

FORD FUSION 2010 car safety problem was reported on Apr 25, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . i have a 2010 ford fusion with a four cylinder engine. while driving to work, i started speeding up from an intersection, only to experience a complete and total loss of power, the wrench light came, the engine started misfiring (rough idle at less than 550 rpm), but all systems where still working. pressing the gas pedal produced no results. i was able to pull off the side of the road, stop the engine, let the car sit for about 15 seconds, and then restarted it. when the engine restarted, the car started up and ran like nothing had happened. yesterday (june 1st), the fusion did the exact same thing, except this time i was pulling into an intersection (approximately 5 miles per hour). i had a catastrophic loss of power, the wrench light came on again, the engine was misfiring (rough idle), the rest of the systems continued working. luckily no one was coming in my direction and i was able to pull off the road into a parking lot, stop the car, and then restart it. i took it to the dealer today and they diagnosed it as needing a new throttle body. they quoted the price and labor at $400 for the repair. i've had this car less than 1 year and it only has 49,800 miles on it. if i had been pulling onto a busy street and experienced the same loss of power, it could have been a much more dangerous situation. according to my research, this is a common problem with the 2010 ford fusion, and the replacement part has been "redesigned" according to the dealer where i took my car for repair. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 47282 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in LEXINGTON, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10460341

FORD FUSION 2010 car safety problem was reported on Apr 25, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i have a 2010 ford fusion with a four cylinder engine. while driving to work, i started speeding up from an intersection, only to experience a complete and total loss of power, the wrench light came, the engine started misfiring (rough idle at less than 550 rpm), but all systems where still working. pressing the gas pedal produced no results. i was able to pull off the side of the road, stop the engine, let the car sit for about 15 seconds, and then restarted it. when the engine restarted, the car started up and ran like nothing had happened. yesterday (june 1st), the fusion did the exact same thing, except this time i was pulling into an intersection (approximately 5 miles per hour). i had a catastrophic loss of power, the wrench light came on again, the engine was misfiring (rough idle), the rest of the systems continued working. luckily no one was coming in my direction and i was able to pull off the road into a parking lot, stop the car, and then restart it. i took it to the dealer today and they diagnosed it as needing a new throttle body. they quoted the price and labor at $400 for the repair. i've had this car less than 1 year and it only has 49,800 miles on it. if i had been pulling onto a busy street and experienced the same loss of power, it could have been a much more dangerous situation. according to my research, this is a common problem with the 2010 ford fusion, and the replacement part has been "redesigned" according to the dealer where i took my car for repair. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 47282 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in LEXINGTON, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10460429

FORD FUSION 2010 car safety problem was reported on June 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . i was driving at approximately 45 mph, when car decelerated, and started to stall. a wrench light was on, and i was able to slowly make my way to a driveway off of the main highway. i turned off the engine, waited for a few minutes before starting the car and making my way home. i plan to take to ford dealer tomorrow. however, it appears, based on many, many complaints, that this is an issue with the throttle body. ford needs to recall/replace this part. my 19-year-old daughter drives this car, and safety is a major issue! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 70000 miles. Ford Fusion 2010 problem was reported in WEST MONROE, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Engine Review #10460520

FORD FUSION 2010 car safety problem was reported on Mar 14, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . while attempting to accelerate, automatic transmission stalls and wrench light illuminates. at first i could turn the car off and back on, but eventually, the car stopped functioning altogether. analysis was performed and throttle body was the cause. has occurred with other 2010 fusion sels. ford unwilling to replace faulty manufactured part. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 36000 miles. Ford Fusion 2010 problem was reported in NASHVILLE, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10460520

FORD FUSION 2010 car safety problem was reported on Mar 14, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while attempting to accelerate, automatic transmission stalls and wrench light illuminates. at first i could turn the car off and back on, but eventually, the car stopped functioning altogether. analysis was performed and throttle body was the cause. has occurred with other 2010 fusion sels. ford unwilling to replace faulty manufactured part. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 36000 miles. Ford Fusion 2010 problem was reported in NASHVILLE, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10460553

FORD FUSION 2010 car safety problem was reported on June 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. while driving approximately 45 mph, the wrench warning symbol illuminated on continuously as the engine stalled. the contact was able to restart the vehicle. the contact stated that the same malfunction occurred in 2010 and the throttle body was replaced by the dealer. the vehicle had not been diagnosed for the most recent failure. the manufacturer was notified of the problem. the approximate failure mileage was 89,000. .0 person(s) were injured. 0 person(s) died.Mileage was 89000 miles. Vehicle Identification Number (VIN):3FAHP0HG1AR. Ford Fusion 2010 problem was reported in WEST MONROE, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10460681

FORD FUSION 2010 car safety problem was reported on Dec 28, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . i have a 2010 ford fusion with a six cylinder engine. while driving , i started speeding up from an intersection, only to experience a complete and total loss of power, the wrench light came, the engine started misfiring (rough idle at less than 700 rpm), but all systems where still working. pressing the gas pedal produced no results. i was able to pull off the side of the road, stop the engine, let the car sit for about 45 seconds, and then restarted it. when the engine restarted, the car started up and ran like nothing had happened. last thursday and friday, the fusion did the exact same thing, i had a catastrophic loss of power, the wrench light came on again, the engine was misfiring (rough idle), the rest of the systems continued working. i was able to pull off the road, stop the car , and then restart. this is third time i take to the dealer, and still received not diagnostic. actually this vehicle is in the dealer workshop (automovilistica veracruzana sa de cv. av lafragua 2100 tel 011 52 229 9231920 veracruz, mexico) . the first and second visit to the dealer the diagnostic was no problem. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 170 miles. Vehicle Identification Number (VIN):3FAHP0HG9AR. Ford Fusion 2010 problem was reported in BROWNSVILLE, TX., TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 4 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10460681

FORD FUSION 2010 car safety problem was reported on Dec 28, 2009.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . i have a 2010 ford fusion with a six cylinder engine. while driving , i started speeding up from an intersection, only to experience a complete and total loss of power, the wrench light came, the engine started misfiring (rough idle at less than 700 rpm), but all systems where still working. pressing the gas pedal produced no results. i was able to pull off the side of the road, stop the engine, let the car sit for about 45 seconds, and then restarted it. when the engine restarted, the car started up and ran like nothing had happened. last thursday and friday, the fusion did the exact same thing, i had a catastrophic loss of power, the wrench light came on again, the engine was misfiring (rough idle), the rest of the systems continued working. i was able to pull off the road, stop the car , and then restart. this is third time i take to the dealer, and still received not diagnostic. actually this vehicle is in the dealer workshop (automovilistica veracruzana sa de cv. av lafragua 2100 tel 011 52 229 9231920 veracruz, mexico) . the first and second visit to the dealer the diagnostic was no problem. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 170 miles. Vehicle Identification Number (VIN):3FAHP0HG9AR. Ford Fusion 2010 problem was reported in BROWNSVILLE, TX., TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 4 mph.

Ford Fusion 2010 Fuel/propulsion System Review #10460745

FORD FUSION 2010 car safety problem was reported on June 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . without warning the car lost all ability to accelerate. this occurred several times over the course of two days, sometimes at speeds up to 70 mph. the car jerks, wrench light comes on, and there is no power from the gas pedal. a/c and radio work fine. after navigating thru traffic without power, we turn car off and back on, and it's good to go. but for how long? could be very dangerous, recall is necessary. dealer says 2010 fusions are "notorious" for this throttle body problem and charged $502 to correct it. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 53000 miles. Vehicle Identification Number (VIN):1FTPX14577N. Ford Fusion 2010 problem was reported in COWETA, OK. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10460745

FORD FUSION 2010 car safety problem was reported on June 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . without warning the car lost all ability to accelerate. this occurred several times over the course of two days, sometimes at speeds up to 70 mph. the car jerks, wrench light comes on, and there is no power from the gas pedal. a/c and radio work fine. after navigating thru traffic without power, we turn car off and back on, and it's good to go. but for how long? could be very dangerous, recall is necessary. dealer says 2010 fusions are "notorious" for this throttle body problem and charged $502 to correct it. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 53000 miles. Vehicle Identification Number (VIN):1FTPX14577N. Ford Fusion 2010 problem was reported in COWETA, OK. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10461024

FORD FUSION 2010 car safety problem was reported on May 18, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . gears just dropped out and car simply idled. had to pull over into left turn lane and turn off vehicle and restart. car worked fine again for two weeks when it happened again. it happened most recently on 06/06/12 three times in one day. once on the way to the office, once on the way home from the office, and once on the way back from my financial advisor's office when i had my fiance in the car. *js.0 person(s) were injured. 0 person(s) died.Mileage was 26000 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in CORAL SPRINGS, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10461070

FORD FUSION 2010 car safety problem was reported on Mar 09, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . engine began shutting down while moving in morning rush hour. also surges forward and runs thru multiple gears while in stop and go traffic with light, if any throttle applied. on 6-8-12 engine went into failsafe mode, 1100 rpm while traveling at 60 mph. no response from throttle, had to manipulate thru traffic to beach car upon shoulder of road. after shutting off key and restarting, vehicle seemed fine, but same situation happened twice more within minutes. drove car to nearest ford dealer who "cleared the old codes" and test drove, finding no further issue. billed me under esp service agreement, and continued onto work. leaving work to make deliveries, car initiated exactly same response as earlier (5 times), at various speeds, and again, heavy traffic. took to dealer i bought car from, who immediately claimed it needed a new throttle body, which are on national back-order, delivery date unknown. referred to another dealer who had open bays and a throttle body in stock, but for some reason was uninterested in even looking at the car. offered to leave car, esp offers rental, so i could return to work, but that part has become uncovered by the extended warranty, and they still had no interest in fixing car after i agreed to pay myself. transmission has a quirky problem of downshifting aggressively when traveling downhill, up-shifting rapidly in slow moving traffic, and now a throttle body problem which causes car to go into a no power situation while at speed. *js.0 person(s) were injured. 0 person(s) died.Mileage was 33240 miles. Vehicle Identification Number (VIN):3FAHP0JG3BR. Ford Fusion 2010 problem was reported in UNION GROVE, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:4WD. FUEL TYPE: BIFUEL. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10461070

FORD FUSION 2010 car safety problem was reported on Mar 09, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . engine began shutting down while moving in morning rush hour. also surges forward and runs thru multiple gears while in stop and go traffic with light, if any throttle applied. on 6-8-12 engine went into failsafe mode, 1100 rpm while traveling at 60 mph. no response from throttle, had to manipulate thru traffic to beach car upon shoulder of road. after shutting off key and restarting, vehicle seemed fine, but same situation happened twice more within minutes. drove car to nearest ford dealer who "cleared the old codes" and test drove, finding no further issue. billed me under esp service agreement, and continued onto work. leaving work to make deliveries, car initiated exactly same response as earlier (5 times), at various speeds, and again, heavy traffic. took to dealer i bought car from, who immediately claimed it needed a new throttle body, which are on national back-order, delivery date unknown. referred to another dealer who had open bays and a throttle body in stock, but for some reason was uninterested in even looking at the car. offered to leave car, esp offers rental, so i could return to work, but that part has become uncovered by the extended warranty, and they still had no interest in fixing car after i agreed to pay myself. transmission has a quirky problem of downshifting aggressively when traveling downhill, up-shifting rapidly in slow moving traffic, and now a throttle body problem which causes car to go into a no power situation while at speed. *js.0 person(s) were injured. 0 person(s) died.Mileage was 33240 miles. Vehicle Identification Number (VIN):3FAHP0JG3BR. Ford Fusion 2010 problem was reported in UNION GROVE, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:4WD. FUEL TYPE: BIFUEL. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10461070

FORD FUSION 2010 car safety problem was reported on Mar 09, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . engine began shutting down while moving in morning rush hour. also surges forward and runs thru multiple gears while in stop and go traffic with light, if any throttle applied. on 6-8-12 engine went into failsafe mode, 1100 rpm while traveling at 60 mph. no response from throttle, had to manipulate thru traffic to beach car upon shoulder of road. after shutting off key and restarting, vehicle seemed fine, but same situation happened twice more within minutes. drove car to nearest ford dealer who "cleared the old codes" and test drove, finding no further issue. billed me under esp service agreement, and continued onto work. leaving work to make deliveries, car initiated exactly same response as earlier (5 times), at various speeds, and again, heavy traffic. took to dealer i bought car from, who immediately claimed it needed a new throttle body, which are on national back-order, delivery date unknown. referred to another dealer who had open bays and a throttle body in stock, but for some reason was uninterested in even looking at the car. offered to leave car, esp offers rental, so i could return to work, but that part has become uncovered by the extended warranty, and they still had no interest in fixing car after i agreed to pay myself. transmission has a quirky problem of downshifting aggressively when traveling downhill, up-shifting rapidly in slow moving traffic, and now a throttle body problem which causes car to go into a no power situation while at speed. *js.0 person(s) were injured. 0 person(s) died.Mileage was 33240 miles. Vehicle Identification Number (VIN):3FAHP0JG3BR. Ford Fusion 2010 problem was reported in UNION GROVE, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:4WD. FUEL TYPE: BIFUEL. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10461093

FORD FUSION 2010 car safety problem was reported on June 07, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . multiple times the engine just dies due to a faulty throttle body - you must come to a complete stop and put the car in park to restart. we have a fleet of these and lots of them have this very dangerous problem. please help... *js.0 person(s) were injured. 0 person(s) died.Mileage was 74802 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in JAMISON, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Unknown Or Other

Ford Fusion 2010 Unknown Or Other Review #10461584

FORD FUSION 2010 car safety problem was reported on Apr 17, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with UNKNOWN OR OTHER . i was driving down the road and suddenly i was losing power. the car was on but stepping on the gas pedal did nothing. the check engine light and the little wrench came on. i coasted into a parking lot and put the car in park. it started to vibrate and make noise. i shut it off and tried to restart it. it seemed normal so i started to drive home. i got about 3 mile and it did it again. it has steadily done this about 2-3 times a week now. one time i was going 65-70 on the express way and had to coast off. the last time i was turning left and i had the green light i was in the middle of the intersection. my light turned red i could have been plowed into and killed. i bought this car may 2011. i have only had this car for 1 year it had 65000 miles, i have no warranty on this car and can not afford to have it fixed. this is dangerous are they waiting for deaths to do anything about it? i have instructed my family if that happens to sue ford. ford knows there is a problem with these cars and should fix it..Mileage was 72000 miles. Vehicle Identification Number (VIN):3FAHP0HA2AR. Ford Fusion 2010 problem was reported in TOLEDO, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Electronic Stability Control

Ford Fusion 2010 Electronic Stability Control Review #10461256

FORD FUSION 2010 car safety problem was reported on May 19, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRONIC STABILITY CONTROL . while driving the car on a sunny day about 35 mph the car started to slow down abruptly to 5 mph. the advance track light came on and service advance track immediately message went across the message center. i immediately took the car to the dealer. light and message were on when i dropped off the car to the dealer. dealer stating could not repeat problem. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 22450 miles. Vehicle Identification Number (VIN):3FAHP0JG2AR. Ford Fusion 2010 problem was reported in NORTH PLAINFIELD, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10461256

FORD FUSION 2010 car safety problem was reported on May 19, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while driving the car on a sunny day about 35 mph the car started to slow down abruptly to 5 mph. the advance track light came on and service advance track immediately message went across the message center. i immediately took the car to the dealer. light and message were on when i dropped off the car to the dealer. dealer stating could not repeat problem. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 22450 miles. Vehicle Identification Number (VIN):3FAHP0JG2AR. Ford Fusion 2010 problem was reported in NORTH PLAINFIELD, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Power Train Review #10461260

FORD FUSION 2010 car safety problem was reported on May 26, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while driving the car at 55mph i let my foot off the gas and then went to accelerate and the car lost all power. would not recognize the gas pedal check engine light and wrench light were on. car died in a construction zone with 3 lanes and no shoulder. extremely dangerous. i pulled car to right lane turned car off and on car continued on. took car to dealer. advised no message was marked in computer. there was nothing wrong could not repeat problem. 5 days later while driving home in traffic the car once again lost all power would not recognize gas pedal, check engine and wrench light came on. i pushed car to the shoulder, turned car off and on continued 100 feet car died again 17 more times. i had car towed to dealer. dealer replaced transmission control. car now shifts horribly, and has a jump when you let off gas. car has stalled numerous times. ford needs to recall for the transmission control module. ford needs to admit there is issues with the transmissions in the v6 fusions. i had similar transmission issues with my ford edge and mercury sable. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 22675 miles. Vehicle Identification Number (VIN):3FAHP0JG2AR. Ford Fusion 2010 problem was reported in NORTH PLAINFIELD, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10461262

FORD FUSION 2010 car safety problem was reported on Mar 14, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . i went for an oil change and local center. the rep requested i come over to the car and see something. the battery acid covered the entire top of battery. it metalized the cables corroded the battery pan. the car is 2 years old and 22k miles. all were replaced by ford under the warranty. i would not normally complain about a battery but this is my second ford to have the same issue. i had ford edge prior which the same thing happened but i was past 36k in miles so they considered it wear and tear. i had to replace all wire, battery pan, and battery. ford needs to review the battery manufacturer they are using in there new cars. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 22150 miles. Vehicle Identification Number (VIN):3FAHP0JG2AR. Ford Fusion 2010 problem was reported in NORTH PLAINFIELD, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10461294

FORD FUSION 2010 car safety problem was reported on June 11, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . i was just leaving my neighborhood and just got down to the end of the road, when all of a sudden i feel this really bad shaking, had no acceleration when pressed on gas and car kept jerking until i finally had to shut it off. i did research on it immediately and found out that this is a throttle body issue that has become very relevant with my car make/model. this is very dangerous! if i was in heavy traffic or god forbid had kids in the car, this could have caused a major accident! this recall needs to be taken seriously and addressed fast!!!! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 29345 miles. Vehicle Identification Number (VIN):3FAHP0JG9AR. Ford Fusion 2010 problem was reported in ROCHESTER, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10461294

FORD FUSION 2010 car safety problem was reported on June 11, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . i was just leaving my neighborhood and just got down to the end of the road, when all of a sudden i feel this really bad shaking, had no acceleration when pressed on gas and car kept jerking until i finally had to shut it off. i did research on it immediately and found out that this is a throttle body issue that has become very relevant with my car make/model. this is very dangerous! if i was in heavy traffic or god forbid had kids in the car, this could have caused a major accident! this recall needs to be taken seriously and addressed fast!!!! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 29345 miles. Vehicle Identification Number (VIN):3FAHP0JG9AR. Ford Fusion 2010 problem was reported in ROCHESTER, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10461301

FORD FUSION 2010 car safety problem was reported on Apr 20, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while driving the vehicle under normal conditions at speed on an open highway the car suddenly lost all throttle control and transmission response, a 'wrench' warning light came on the vehicle gauge cluster. after coasting to a stop in the breakdown lane the car sat, idled roughly, and i turned the ignition off. after a minute or two i started the car and the symptoms (including the wrench warning light) were gone. i brought the vehicle to the dealer service desk and after analysis was told there were no events captured by the vehicle computer. i was told to drive the car and report any additional instances of the problem. after the issue resurfaced again three weeks later, i again brought the vehicle to the service team at my dealership. after again not finding events logged in the computer, they installed a temporary data recorder for me to manually engage the next time the issue appeared. i was lucky to have the problem the very next day, the recorder captured the event and reflected the problem was with the throttle body. the dealer replaced the unit. upon researching the issue after the first instance it is clear there are hundreds of cases of this same problem documented in various forms and sites on the web indicating this is a known, systemic problem for ford with the fusion throttle body. the nature of the problem, effecting vehicle control, at speed, is dangerous and would seem to warrant a more proactive approach to the issue both by ford and by the nhtsa. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 34800 miles. Vehicle Identification Number (VIN):3FAHP0CG2AR. Ford Fusion 2010 problem was reported in FITCHBURG, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train Review #10461303

FORD FUSION 2010 car safety problem was reported on May 15, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . my fusion has become erratic in low gear shifts. when trying to merge into traffic and turn onto a highway it will act as though it is in neutral and i have no power to get out in traffic. i have been almost hit on a major highway do to this mechanical failure. i took the car to a dealership for repair and they informed me that it was low on transmission fluid and they repaired a seal and reprogrammed it as ford directed. i took the car on a trip and i was unable to merge into traffic again and it ran at over 5000rpm on the highway for long periods of time. it finally flipped a code and i returned it to the dealership. they did a complete transmission overhaul and replaced over 15 parts. this took two weeks with them having to deal with fords warranty department. i picked up the car on 6/6/2012 and it did not even make it to my place of work, 12 miles away, without the transmission slipping again and it remaining in neutral. this car is a death trap!! i called the dealership and they came and picked it up. it is now 6/12/2012 and i still do not have a car to drive. the dealership is fighting with ford to have the complete transmission replaced. ford has contacted me several times and it seems as though they do not care that this car is a danger to have on the road. i want my car back in working condition. i am pleased with my dealership of choice for service as they have been very polite and helpful with me. ford has given me nothing to drive in the meantime. people, if you have this issue with your car make sure ford hears your complaint. this is dangerous and unacceptable. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 28453 miles. Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in NEW PARIS, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 5 mph.

Ford Fusion 2010 Power Train Review #10461305

FORD FUSION 2010 car safety problem was reported on June 11, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i was driving down the highway when i lost the ability to accelerate. my rpms dropped and i had to pull over. i called ford roadside services, they came and picked up my car. after being looked at by the ford dealership, it was determined my throttle body needed to be replaced. my car is less than 2 years old and only has 40,000 miles on it. the part and labor totaled around $500.00 this is ridiculous for a new car to already have this issues. i did some research on the internet and found that multiple ford fusions are having the same issue. this item needs to be recalled and replaced. i can only thank god it was during the day and in a public area. if this had been at night with my 7 year in a bad area, no telling what could have happened. i was lucky the people behind me on the freeway noticed i was slowing down or i could have been involved in an accident. ford needs to step up and fix this. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 41440 miles. Vehicle Identification Number (VIN):3FAHPOHA5AR. Ford Fusion 2010 problem was reported in FRIENDSWOOD, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10461382

FORD FUSION 2010 car safety problem was reported on June 11, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . driving in the left lane of a multi-lane road. the light had just gone yellow and all of a sudden the engine hicupped hard and i had no response to the gas pedal at all, plus the check engine light (wrench icon) came on. put on my signal and pulled into the left turn lane as it was empty. i didn't want to block the left lane, it was the start of rush hour traffic. i came to a stop and had no vehicle movement in response to stepping on the gas pedal. i put the vehicle in park, turned off the engine and tried to restart it. the check engine light went away and the car started and acted normal. i stopped at the store on the way home, then on the way from the store to home it happened again. i had to stop the vehicle and put it in park and turn it off in order for it to start again. when i got home i put a code reader on the vehicle, but it showed no code. it did it again on my way to work in the morning and again on the way home after work. each time i have to maneuver the vehicle to the side of the road and come to a complete stop, put it in park and turn it off and back on to get it to start again. this is extremely dangerous for me and anyone around me. i take my vehicle to ford for servicing and they say no recalls are in place for this. i enter the symptoms into the search engine of the internet and find numerous complaints from other owners and drivers of the same defect. there is a problem with the electronic throttle body. i called my local ford dealer and they say that first they have to run tests to verify the throttle body is the problem and i will be charged for that, because the code resets each time. the total bill will be $600 to $700. they have dealt with it before, but ford has nothing in place to address it as a safety issue. please don't wait til someone gets hurt or possibly killed before this matter is taken seriously and proper measures are taken. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 36321 miles. Ford Fusion 2010 problem was reported in WAYNESVILLE, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10461382

FORD FUSION 2010 car safety problem was reported on June 11, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . driving in the left lane of a multi-lane road. the light had just gone yellow and all of a sudden the engine hicupped hard and i had no response to the gas pedal at all, plus the check engine light (wrench icon) came on. put on my signal and pulled into the left turn lane as it was empty. i didn't want to block the left lane, it was the start of rush hour traffic. i came to a stop and had no vehicle movement in response to stepping on the gas pedal. i put the vehicle in park, turned off the engine and tried to restart it. the check engine light went away and the car started and acted normal. i stopped at the store on the way home, then on the way from the store to home it happened again. i had to stop the vehicle and put it in park and turn it off in order for it to start again. when i got home i put a code reader on the vehicle, but it showed no code. it did it again on my way to work in the morning and again on the way home after work. each time i have to maneuver the vehicle to the side of the road and come to a complete stop, put it in park and turn it off and back on to get it to start again. this is extremely dangerous for me and anyone around me. i take my vehicle to ford for servicing and they say no recalls are in place for this. i enter the symptoms into the search engine of the internet and find numerous complaints from other owners and drivers of the same defect. there is a problem with the electronic throttle body. i called my local ford dealer and they say that first they have to run tests to verify the throttle body is the problem and i will be charged for that, because the code resets each time. the total bill will be $600 to $700. they have dealt with it before, but ford has nothing in place to address it as a safety issue. please don't wait til someone gets hurt or possibly killed before this matter is taken seriously and proper measures are taken. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 36321 miles. Ford Fusion 2010 problem was reported in WAYNESVILLE, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Structure

Ford Fusion 2010 Structure Review #10461682

FORD FUSION 2010 car safety problem was reported on June 13, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE . i opened the storage console that sits on the dash and the lid broke off the hinges. parts are made of that hard plastic the heat and sun bakes till brittle. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 57000 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in ROCKPORT, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10461694

FORD FUSION 2010 car safety problem was reported on Apr 23, 2010.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . after stopping for a red signal in traffic (vehicle travel uphill) the vehicle lost drive (acted as if the vehicle had been shifted out of gear). after a harsh engagement, the vehicle regained drive. the vehicle was driven home without further incident that day. the vehicle was taken to a dealer to get the pcm "flashed", i assume with a new shift profile. the vehicle malfunctioned two more times with a data recorder from the dealership installed. the loss of drive occurred after rapidly decelerating to slightly less than 40 mph and then trying to accelerate to the previous speed. again, engagement was harsh when the transmission began to provide drive. ford has acknowledged at least one engine rpm spike from the recorder, but denies that it is significant or that it is indicative of a problem. i have had the transmission fluid from this vehicle tested at an independent laboratory. the sample results showed the transmission fluid to be high in aluminum (7 times the average for a unit with similar miles), and high in iron about 1.6 times the average. this problem is a great safety concern because if the vehicle were to lose drive when pulling out into traffic, an accident involving injury or death could occur! i have found a youtube video posted that represents the problem i am experiencing by using the google search engine and using the querry "ford fusion transmission problems" since the pcm flash the automatic transmission seems to behave at times like a manual transmission. on a coastdown it seems like the transmission is "pushing " the car like a manual transmission with the clutch engaged even though i want the car to coast down. the reprogramming has made shifting more harsh in some gear changes, and seem to skip over the problem gears in other shifts. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 45800 miles. Vehicle Identification Number (VIN):3FAHP0HG0AR. Ford Fusion 2010 problem was reported in ALIQUIPPA, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train Review #10462166

FORD FUSION 2010 car safety problem was reported on June 16, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . on saturday june 16th i was traveling north bound i-75 from rockcastle co. ky to madison co ky which is about 45 miles. was traveling 65 miles mph and suddenly the engine shut off. there was a semi in the right lane, we were in the middle lane with one semi in back of us. we were able to coast to the emergency side of the road. the semi in back of us locked his brake and almost hit us. i shut the car off and restarted it and drove in the slow lane and it happened 3 more times. i then left the car at my mother in-law's house and borrowed a car to get home in as i was afraid to drive it and put myself at risk plus someone's life at risk. on monday, 6-18-12 i got the car to the dealership and the mechanic test drove it and it happened to him. i pulled up on the internet and saw that i am not the only one this has happened to. it definitely is a life ending crash getting ready to happen. of course my vehicle is out of warranty as of 35000 miles, but that is not my issue. i would hate to see someone lose their life due a malfunction of a throttle body. ford needs to step up to the plate and admit that know of this issue and fix it before someone loses their life or a child's life. the foreign makers such as toyota stepped up and ford needs to do so also. this is the fourth automobile i have brought from them and try to stay with the american made cars. safety should be their concern instead of the almighty dollar. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 42000 miles. Vehicle Identification Number (VIN):3FAHP0JG8AR. Ford Fusion 2010 problem was reported in MOUNT VERNON, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10462166

FORD FUSION 2010 car safety problem was reported on June 16, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . on saturday june 16th i was traveling north bound i-75 from rockcastle co. ky to madison co ky which is about 45 miles. was traveling 65 miles mph and suddenly the engine shut off. there was a semi in the right lane, we were in the middle lane with one semi in back of us. we were able to coast to the emergency side of the road. the semi in back of us locked his brake and almost hit us. i shut the car off and restarted it and drove in the slow lane and it happened 3 more times. i then left the car at my mother in-law's house and borrowed a car to get home in as i was afraid to drive it and put myself at risk plus someone's life at risk. on monday, 6-18-12 i got the car to the dealership and the mechanic test drove it and it happened to him. i pulled up on the internet and saw that i am not the only one this has happened to. it definitely is a life ending crash getting ready to happen. of course my vehicle is out of warranty as of 35000 miles, but that is not my issue. i would hate to see someone lose their life due a malfunction of a throttle body. ford needs to step up to the plate and admit that know of this issue and fix it before someone loses their life or a child's life. the foreign makers such as toyota stepped up and ford needs to do so also. this is the fourth automobile i have brought from them and try to stay with the american made cars. safety should be their concern instead of the almighty dollar. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 42000 miles. Vehicle Identification Number (VIN):3FAHP0JG8AR. Ford Fusion 2010 problem was reported in MOUNT VERNON, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10462354

FORD FUSION 2010 car safety problem was reported on June 19, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . over the last couple weeks i have noticed slight jerks or sputters when i'm driving. speed ranges anywhere from 10-70 mph when it occurs. this morning on the highway it was much more noticeable and after about 10 miles the wrench light came on and i lost all acceleration, luckily the right lane was clear and i could get to the shoulder safely. as i slowed down the engine shook heavily and i turned the car off. i waited a couple minutes and restarted the car fine...no light, no shaking. i was able to drive the 3.5 miles to work. same day, driving home i made it about 10 miles again and the same thing happened. i waited a couple minutes, restarted and made it to a shop a couple miles down the road (still could feel the jerking slightly but the light didn't come on and i didn't lose acceleration). once i got there and they hooked up the diagnostic machine they could not read any codes, which is very common from what i'm reading about other fusion owners who have this problem. they are going to drive it in the morning so they can read the code when the light comes on and hopefully determine if it is the throttle body. i am so frustrated as this car is barely 2 years old and apparently this is a very common and dangerous problem. *js.0 person(s) were injured. 0 person(s) died.Mileage was 57700 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in OWASSO, OK. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10462376

FORD FUSION 2010 car safety problem was reported on June 25, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while driving on the interstate at about 55 mph, the vehicle lost all power and shut down with the wrench and check engine lights were on. steering was difficult and i almost was hit trying to get vehicle off of the road. after several minutes i tried restarting car and it started, so i made it to my destination and it died again. i had to have it towed to ford. the vehicle was under warranty and they replaced the throttle body assembly. vehicle still has loss of power issues and ford has not solved this issue. this is dangerous as vehicle just turns off at highway speed as this part fails. *js.0 person(s) were injured. 0 person(s) died.Mileage was 27000 miles. Ford Fusion 2010 problem was reported in DELAND, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Steering

Ford Fusion 2010 Steering Review #10462376

FORD FUSION 2010 car safety problem was reported on June 25, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with STEERING . while driving on the interstate at about 55 mph, the vehicle lost all power and shut down with the wrench and check engine lights were on. steering was difficult and i almost was hit trying to get vehicle off of the road. after several minutes i tried restarting car and it started, so i made it to my destination and it died again. i had to have it towed to ford. the vehicle was under warranty and they replaced the throttle body assembly. vehicle still has loss of power issues and ford has not solved this issue. this is dangerous as vehicle just turns off at highway speed as this part fails. *js.0 person(s) were injured. 0 person(s) died.Mileage was 27000 miles. Ford Fusion 2010 problem was reported in DELAND, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Unknown Or Other

Ford Fusion 2010 Unknown Or Other Review #10462663

FORD FUSION 2010 car safety problem was reported on Mar 16, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with UNKNOWN OR OTHER . car began to lurch and unable to accelerate. check engine and wrench light appeared. had to pull over and manually turn off car. turned off radio, and air conditioner, restarted car and was able to drive home. car has had same issue several times, occurring more and more frequently. vehicle to service on 6/19/2012, mechanic diagnosed a throttle box failure..0 person(s) were injured. 0 person(s) died.Mileage was 44350 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in BLOOMINGTON, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10462619

FORD FUSION 2010 car safety problem was reported on May 11, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . the car would not start on the first two tries and i let it sit a moment and it started on the third try. *tt.0 person(s) were injured. 0 person(s) died.Mileage was 53000 miles. Vehicle Identification Number (VIN):3FAHP0GAXAR. Ford Fusion 2010 problem was reported in MAYNARDVILLE, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10462619

FORD FUSION 2010 car safety problem was reported on May 11, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . the car would not start on the first two tries and i let it sit a moment and it started on the third try. *tt.0 person(s) were injured. 0 person(s) died.Mileage was 53000 miles. Vehicle Identification Number (VIN):3FAHP0GAXAR. Ford Fusion 2010 problem was reported in MAYNARDVILLE, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10462665

FORD FUSION 2010 car safety problem was reported on June 18, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . the car had run fine on my way to work and leaving for lunch. it would not start when i tried to return from lunch. same problem as last month, it would not start until the third try. *tt.0 person(s) were injured. 0 person(s) died.Mileage was 55000 miles. Vehicle Identification Number (VIN):3FAHP0GAXAR. Ford Fusion 2010 problem was reported in MAYNARDVILLE, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10462665

FORD FUSION 2010 car safety problem was reported on June 18, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . the car had run fine on my way to work and leaving for lunch. it would not start when i tried to return from lunch. same problem as last month, it would not start until the third try. *tt.0 person(s) were injured. 0 person(s) died.Mileage was 55000 miles. Vehicle Identification Number (VIN):3FAHP0GAXAR. Ford Fusion 2010 problem was reported in MAYNARDVILLE, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10463026

FORD FUSION 2010 car safety problem was reported on June 27, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . tl* the contact owns a 2010 ford fusion. the contact stated that while driving approximately 65 mph with the air conditioner activated, the engine stalled and immediately the warning indicator began to illuminate. the vehicle was coasted to the side of the road and after waiting a few moments, the vehicle restarted. the failure occurred four times when driving at various speeds with the air conditioner activated. the vehicle had not been diagnosed or repaired. the manufacturer was not notified of the problem. the approximate failure mileage was 45,000. .0 person(s) were injured. 0 person(s) died.Mileage was 45000 miles. Vehicle Identification Number (VIN):3FAHP0JG9AR. Ford Fusion 2010 problem was reported in FREDERICKBURG, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10463222

FORD FUSION 2010 car safety problem was reported on June 25, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . while driving my car it suddenly jerked and stopped like i had turned it off. i coasted to side of road it was still running could not give it any gas a wrench light came on. i turned off car and restarted it, and it came back on, and the wrench light went off. drove it on home it jumped and jerked like it was going to quit at any moment. i then took it to my dealership they ran a diagnostic test on it said it was throttle body but was not covered under my warranty. i have had no problems with this car since purchasing it but have only had it less than a year. i am concerned with a serious accident happening because it just shuts off the gas and i cannot move it or get it out of traffic..0 person(s) were injured. 0 person(s) died.Mileage was 45719 miles. Vehicle Identification Number (VIN):3FAHP0JG5AR. Ford Fusion 2010 problem was reported in ROME, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Vehicle Speed Control Review #10463387

FORD FUSION 2010 car safety problem was reported on June 27, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . while traveling in traffic the car lost power. i was able to steer to the shoulder of the road where the car idled roughly and i noticed a "wrench" light came on. i shut the car down while i collected my thoughts on what to do. i used my phone to find the closest ford dealer and, before calling for a tow vehicle, i tried to restart the car. it restarted, the wrench light was off, and it seemed to run fine. i drove directly to the nearest ford dealer without incident where they hooked up the computer to see what was wrong. they could find nothing wrong and suggested the next time it happened to try and get it to a dealer while the light was on. i then drove approximately 120 miles home with my grandson. this morning i went on the internet to see if there were any similar instances such as mind and found there were quite a few: (http://www.arfc.org/complaints/2010/ford/fusion/power_train/problem.aspx) the incidents others reported were almost identical to mine. i then called the dealer i bought the car from new, and they ran a check to see if there were any recalls on my model and there weren't. they suggested i call ford customer service. i tried calling them and was told by a representative they were having "technical issues" and couldn't help me, to call back in an hour. i live in a very rural area. the closest ford dealer is probably 50-60miles away. the roads here don't have much room to pull off on if the car fails again. judging by the complaints i have seen online, it seems there is a problem with this car and there should be some action being taken to remedy it. this situation creates a safety hazard for anyone driving or riding in the car. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 40891 miles. Vehicle Identification Number (VIN):3FAHP0JG1AR. Ford Fusion 2010 problem was reported in HAGUE, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10463387

FORD FUSION 2010 car safety problem was reported on June 27, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while traveling in traffic the car lost power. i was able to steer to the shoulder of the road where the car idled roughly and i noticed a "wrench" light came on. i shut the car down while i collected my thoughts on what to do. i used my phone to find the closest ford dealer and, before calling for a tow vehicle, i tried to restart the car. it restarted, the wrench light was off, and it seemed to run fine. i drove directly to the nearest ford dealer without incident where they hooked up the computer to see what was wrong. they could find nothing wrong and suggested the next time it happened to try and get it to a dealer while the light was on. i then drove approximately 120 miles home with my grandson. this morning i went on the internet to see if there were any similar instances such as mind and found there were quite a few: (http://www.arfc.org/complaints/2010/ford/fusion/power_train/problem.aspx) the incidents others reported were almost identical to mine. i then called the dealer i bought the car from new, and they ran a check to see if there were any recalls on my model and there weren't. they suggested i call ford customer service. i tried calling them and was told by a representative they were having "technical issues" and couldn't help me, to call back in an hour. i live in a very rural area. the closest ford dealer is probably 50-60miles away. the roads here don't have much room to pull off on if the car fails again. judging by the complaints i have seen online, it seems there is a problem with this car and there should be some action being taken to remedy it. this situation creates a safety hazard for anyone driving or riding in the car. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 40891 miles. Vehicle Identification Number (VIN):3FAHP0JG1AR. Ford Fusion 2010 problem was reported in HAGUE, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10463400

FORD FUSION 2010 car safety problem was reported on June 28, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact was driving approximately 60 mph when the engine stalled with the illumination of the wrench symbol, and engine warning indicators. the vehicle restarted after two attempts. the vehicle was taken to an independent mechanic where the throttle body assembly was replaced. the manufacturer was not notified of the problem. the approximate failure mileage was 44,500. .0 person(s) were injured. 0 person(s) died.Mileage was 44500 miles. Vehicle Identification Number (VIN):3FAHP0JA0AR. Ford Fusion 2010 problem was reported in LANGHORNE, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Fuel System, Gasoline

Ford Fusion 2010 Fuel System, Gasoline Review #10463416

FORD FUSION 2010 car safety problem was reported on May 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE . i was sitting at a red light when the light turned green and i put on the gas the car jumped. the engine light came on. i pulled over to the side of the road. the car had no acceleration but still had power. i turned off the vehicle and turned it back on. the car started back up and the light went off. i took the car to a auto repair shop. the diagnostic test stated it is the throttle body going bad. the mechanic cleaned this part good and the sensors. the car has run fine for about three weeks with out any problems until 06/11/12 then it started again it has done it four times since and the engine light will not go off. i have used high test gas in it. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in COLUMBUS, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10463416

FORD FUSION 2010 car safety problem was reported on May 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . i was sitting at a red light when the light turned green and i put on the gas the car jumped. the engine light came on. i pulled over to the side of the road. the car had no acceleration but still had power. i turned off the vehicle and turned it back on. the car started back up and the light went off. i took the car to a auto repair shop. the diagnostic test stated it is the throttle body going bad. the mechanic cleaned this part good and the sensors. the car has run fine for about three weeks with out any problems until 06/11/12 then it started again it has done it four times since and the engine light will not go off. i have used high test gas in it. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in COLUMBUS, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Structure Body

Ford Fusion 2010 Structure Body Review #10463555

FORD FUSION 2010 car safety problem was reported on June 09, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE:BODY . took car for oil change. noticed after car wasn't locking on driver's side. passenger then noticed interior driver's side door handle was cracked and not flushed with door. door no longer locks essentially leaving my car unprotected from theft. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 55000 miles. Vehicle Identification Number (VIN):3FAHP0JA5AR. Ford Fusion 2010 problem was reported in STUART, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Latches/locks/linkages

Ford Fusion 2010 Latches/locks/linkages Review #10463555

FORD FUSION 2010 car safety problem was reported on June 09, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with LATCHES/LOCKS/LINKAGES . took car for oil change. noticed after car wasn't locking on driver's side. passenger then noticed interior driver's side door handle was cracked and not flushed with door. door no longer locks essentially leaving my car unprotected from theft. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 55000 miles. Vehicle Identification Number (VIN):3FAHP0JA5AR. Ford Fusion 2010 problem was reported in STUART, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10463645

FORD FUSION 2010 car safety problem was reported on Apr 25, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . the first time, the car was pulling on to a main road going up to 15 mph while turning right. the car began to shudder, stall (only able to coast to a stop), many warning lights including the wrench light came on and dinged. after shutting the key off and waiting up to a couple of minutes, engine started fine and drove normally. 1 month later, this exact scenario happened again while turning right from a complete stop. 1 month later, it happened again but with only the yellow wrench light coming on (the car was curving to the right at about 40 mph). 2 days later the car did the same thing at about 35 mph. this time the car would start up, and be fine until we accelerated. we narrowly avoided an accident when the car did the same thing a second time. it then did it a third time and we waited to start the car. we were then able to drive the car home normally with a code alert on the dash. i took the car to get a diagnosis and they showed code p2111. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 55000 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in LANSING, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10463645

FORD FUSION 2010 car safety problem was reported on Apr 25, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . the first time, the car was pulling on to a main road going up to 15 mph while turning right. the car began to shudder, stall (only able to coast to a stop), many warning lights including the wrench light came on and dinged. after shutting the key off and waiting up to a couple of minutes, engine started fine and drove normally. 1 month later, this exact scenario happened again while turning right from a complete stop. 1 month later, it happened again but with only the yellow wrench light coming on (the car was curving to the right at about 40 mph). 2 days later the car did the same thing at about 35 mph. this time the car would start up, and be fine until we accelerated. we narrowly avoided an accident when the car did the same thing a second time. it then did it a third time and we waited to start the car. we were then able to drive the car home normally with a code alert on the dash. i took the car to get a diagnosis and they showed code p2111. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 55000 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in LANSING, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10463645

FORD FUSION 2010 car safety problem was reported on Apr 25, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . the first time, the car was pulling on to a main road going up to 15 mph while turning right. the car began to shudder, stall (only able to coast to a stop), many warning lights including the wrench light came on and dinged. after shutting the key off and waiting up to a couple of minutes, engine started fine and drove normally. 1 month later, this exact scenario happened again while turning right from a complete stop. 1 month later, it happened again but with only the yellow wrench light coming on (the car was curving to the right at about 40 mph). 2 days later the car did the same thing at about 35 mph. this time the car would start up, and be fine until we accelerated. we narrowly avoided an accident when the car did the same thing a second time. it then did it a third time and we waited to start the car. we were then able to drive the car home normally with a code alert on the dash. i took the car to get a diagnosis and they showed code p2111. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 55000 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in LANSING, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Engine Review #10464040

FORD FUSION 2010 car safety problem was reported on June 02, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . i was sitting at a red light, when the light turned green i accelerated through the light. upon making the turn, the car stalled (shuddered, and although applying the gas, nothing happened) and the 'wrench' icon illuminated. i pulled over to the side of the road (thankfully there was little traffic at this time of day), turned the car off, waited a minute, and re-started the car. the average speed for that day was 30mph, through neighborhoods and light commercial area. the car stalled once again (about 10 minutes later) while at a stop sign, at another intersection. i was able to restart the car again, and took it to my mechanic. the stalling has reoccurred multiple times, even when slowing, but not stopping, and attempting to resume speed. the diagnosis was the throttle body. the mechanic replaced the throttle body, the throttle sensor (on advice from the ford dealership in the area), and after 1 month of this issue reoccurring, had the ford dealership 'flash' the computer. this has still not solved the problem. typically after 2 days of retrieving the vehicle from the mechanic, the same stalling with the wrench icon occurs. this is a safety issue! many vehicles are stalling in traffic, and accidents will occur! *js.0 person(s) were injured. 0 person(s) died.Mileage was 37200 miles. Vehicle Identification Number (VIN):3FAHP0JG9AR. Ford Fusion 2010 problem was reported in SPRING, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: BIFUEL. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10464141

FORD FUSION 2010 car safety problem was reported on June 23, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact was driving 65 mph when the wrench warning symbol illumined. the contact also stated that the vehicle started decelerating and stalled. the vehicle was towed to the dealer for diagnosis and the dealer advised that the throttle body needed to be replaced. the vehicle was repaired.the manufacturer was contacted and stated that the vehicle was not under warranty. the failure and the current mileage was 42,000. the vin was not available. .0 person(s) were injured. 0 person(s) died.Mileage was 42000 miles. Ford Fusion 2010 problem was reported in CANTON, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Vehicle Speed Control Review #10464155

FORD FUSION 2010 car safety problem was reported on July 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . while stopped with foot on break - the engine began to rev and the car began to lurch forward. i had to keep pressing harder on the brake i looked down to be sure i did not have my foot on the gas and i did not. i had to put the car in park and turn off the ignition to get the car to stop reving up and lurching forward. my wife told me she had a similar incident with the engine reving up when she had the car on cruise control but it only lasted a few moments, in that incident she was going 60. also, we do not have the floor mats that we read about in other posts online. *js.0 person(s) were injured. 0 person(s) died.Mileage was 34500 miles. Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in NEW CARLISLE, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10464155

FORD FUSION 2010 car safety problem was reported on July 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . while stopped with foot on break - the engine began to rev and the car began to lurch forward. i had to keep pressing harder on the brake i looked down to be sure i did not have my foot on the gas and i did not. i had to put the car in park and turn off the ignition to get the car to stop reving up and lurching forward. my wife told me she had a similar incident with the engine reving up when she had the car on cruise control but it only lasted a few moments, in that incident she was going 60. also, we do not have the floor mats that we read about in other posts online. *js.0 person(s) were injured. 0 person(s) died.Mileage was 34500 miles. Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in NEW CARLISLE, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10464169

FORD FUSION 2010 car safety problem was reported on June 20, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . on take off in heavy traffic the transmission slipped and jerked hard. i was frightened and pulled over for about 20 minutes to call my dad whom is a mechanic. he stated that it was the transmission and that i should drive it home which was a hour away. i was scared that it would do it again at full speed. 2 days later as i tried to reverse out of my driveway the car revved up but didn't move then jerked into gear and i flew out the driveway very hard and jerking violently. i don't want to drive with my niece or my little 4 year old brother in case of something dangerous. i haven't experienced this ever with a vehicle. i plan to take the car in immediately! i have been driving another car for the moment. because i have to travel alot. *js.0 person(s) were injured. 0 person(s) died.Ford Fusion 2010 problem was reported in GARRISON, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10464169

FORD FUSION 2010 car safety problem was reported on June 20, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . on take off in heavy traffic the transmission slipped and jerked hard. i was frightened and pulled over for about 20 minutes to call my dad whom is a mechanic. he stated that it was the transmission and that i should drive it home which was a hour away. i was scared that it would do it again at full speed. 2 days later as i tried to reverse out of my driveway the car revved up but didn't move then jerked into gear and i flew out the driveway very hard and jerking violently. i don't want to drive with my niece or my little 4 year old brother in case of something dangerous. i haven't experienced this ever with a vehicle. i plan to take the car in immediately! i have been driving another car for the moment. because i have to travel alot. *js.0 person(s) were injured. 0 person(s) died.Ford Fusion 2010 problem was reported in GARRISON, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10464556

FORD FUSION 2010 car safety problem was reported on July 02, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . i was traveling uphill on a rural road when my car started shaking and would not accelerate. the wrench light came on followed by the engine light. i pulled off the road as far as i could turned the car off and back on it went a little further and started shaking again. i was on a blind curve on a road that is narrow and traveled faster than it should be fortunately i was able to coax the car to an area where the road opens up a little. i had to leave the car overnight and someone chose to vandalize it. i had it towed to the dealer who was a little rude when i talked to them. the dealer said it was the electronic throttle body and it is not something covered by ford. so now i have to pay for this part and labor cost and my deductible for the vandalization. with so many other complaints posted here i don't understand why nothing is being done. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 47000 miles. Ford Fusion 2010 problem was reported in HOME, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10464623

FORD FUSION 2010 car safety problem was reported on July 08, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . today i was at a red light when my car decided to act up. the light had just turned green and i had started to drive when all of the sudden my car lost power. it struggled then just stalled right in the middle of traffic. i looked at the dash and i noticed the wrench light came on. while i was trying not to die in traffic i put my car into neutral where i turned the key to the off position then back to the on position. luckily my car came back on but it was still struggling. i managed to get the car to a nearby parking lot where turned it off again. i gave it a few minutes to recover then turned it back on again. everything now appeared to working normal. i opened the hood to make sure everything seamed okay (nothing burning, smoking, or anything else out of the ordinary), everything checked out okay. also i would like to mention that my transmission sometimes fails to go into gear then all the sudden it goes into gear and jerks really hard. additionally my lower gears will shift very hard. when it shifts it acts as if someone had pushed in the clutch for to long then it goes into gear. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 44500 miles. Ford Fusion 2010 problem was reported in LOUISVILLE, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 2 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10464623

FORD FUSION 2010 car safety problem was reported on July 08, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . today i was at a red light when my car decided to act up. the light had just turned green and i had started to drive when all of the sudden my car lost power. it struggled then just stalled right in the middle of traffic. i looked at the dash and i noticed the wrench light came on. while i was trying not to die in traffic i put my car into neutral where i turned the key to the off position then back to the on position. luckily my car came back on but it was still struggling. i managed to get the car to a nearby parking lot where turned it off again. i gave it a few minutes to recover then turned it back on again. everything now appeared to working normal. i opened the hood to make sure everything seamed okay (nothing burning, smoking, or anything else out of the ordinary), everything checked out okay. also i would like to mention that my transmission sometimes fails to go into gear then all the sudden it goes into gear and jerks really hard. additionally my lower gears will shift very hard. when it shifts it acts as if someone had pushed in the clutch for to long then it goes into gear. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 44500 miles. Ford Fusion 2010 problem was reported in LOUISVILLE, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 2 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10464678

FORD FUSION 2010 car safety problem was reported on June 15, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while cruising between 65 - 70 mph, vehicle stuttered, then "throttle control/transmission' warning light illuminated, and vehicle lost power. accelerator pedal completely unresponsive and engine becomes erratic, but power steering and other electrical components unaffected. able to coast to side of road, where engine continues to sputter, but does not stall. changing transmission position has no effect. turning vehicle off and then back on appears to rectify the condition. two identical occurrences, but first time (06/15/12) with cruise control on, second time (07/06/12) with cruise control off. dealership unable to find source of problem. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 32000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in BETHPAGE, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 68 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10464678

FORD FUSION 2010 car safety problem was reported on June 15, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . while cruising between 65 - 70 mph, vehicle stuttered, then "throttle control/transmission' warning light illuminated, and vehicle lost power. accelerator pedal completely unresponsive and engine becomes erratic, but power steering and other electrical components unaffected. able to coast to side of road, where engine continues to sputter, but does not stall. changing transmission position has no effect. turning vehicle off and then back on appears to rectify the condition. two identical occurrences, but first time (06/15/12) with cruise control on, second time (07/06/12) with cruise control off. dealership unable to find source of problem. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 32000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in BETHPAGE, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 68 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10464678

FORD FUSION 2010 car safety problem was reported on June 15, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . while cruising between 65 - 70 mph, vehicle stuttered, then "throttle control/transmission' warning light illuminated, and vehicle lost power. accelerator pedal completely unresponsive and engine becomes erratic, but power steering and other electrical components unaffected. able to coast to side of road, where engine continues to sputter, but does not stall. changing transmission position has no effect. turning vehicle off and then back on appears to rectify the condition. two identical occurrences, but first time (06/15/12) with cruise control on, second time (07/06/12) with cruise control off. dealership unable to find source of problem. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 32000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in BETHPAGE, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 68 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10464696

FORD FUSION 2010 car safety problem was reported on Feb 02, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact stated that while driving 70 mph, the vehicle stalled and the throttle control warning lamp illuminated. the contact mentioned that the failure recurred several times. the vehicle was taken to the dealer who diagnosed that the throttle was defective and needed to be replaced. the manufacturer was made aware of the failure who did not offer any assistance. the vehicle was not repaired. the failure mileage was 40,000 and the current mileage was 48,000. .0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Vehicle Identification Number (VIN):3FAHP0JG9AR. Ford Fusion 2010 problem was reported in HIGHLAND SPRINGS, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Vehicle Speed Control Review #10464839

FORD FUSION 2010 car safety problem was reported on June 25, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact stated while driving 40 mph, she attempted to accelerate and the vehicle did not respond. the wrench maintenance warning light illuminated on the instrument panel. the contact depressed the brake pedal and the vehicle began stalling and shaking, even as the contact shifted into park gear. the contact applied the emergency brake, turned off vehicle and restarted it. after the vehicle was restarted, the maintenance warning light was no longer illuminated. the failure was resolved momentarily. the contact continued driving and the failure recurred every five miles. the vehicle was towed to a repair shop where the vehicle was inspected and the failure was found in the throttle body. the air filter was defective and a burned spark plug was found. the approximate current and failure mileage was 54,000. .0 person(s) were injured. 0 person(s) died.Mileage was 54000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in SEVERN, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10465073

FORD FUSION 2010 car safety problem was reported on July 09, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . tl* the contact owns a 2010 ford fusion. the contact stated that while driving 20 mph, the vehicle accelerated abnormally before stalling. the check engine and wrench warning lights were illuminated on the instrument panel during the failure. the contact was able to restart the vehicle as the vehicle resumed normal operation. the contact took the vehicle to a dealer but the vehicle was not repaired. the cause of the failure was unknown. the manufacturer was not notified of the issue. the failure mileage was 89,000. the vin was unavailable. .0 person(s) were injured. 0 person(s) died.Mileage was 89000 miles. Ford Fusion 2010 problem was reported in SILVER SPRING, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Engine Review #10465231

FORD FUSION 2010 car safety problem was reported on June 13, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . i and my children were traveling down the highway at 60 mph and i all of a sudden i could not give the car any gas. the motor was still running but i had no control over the gas. so i coasted until i could pull over. as i slowed down, the car shuttered. i turned the car off and restarted it. it ran fine for awhile. then it happened again and again (as i was entering an intersection, turning onto a major highway, and rounding a curve) until it was happening 3-4 times in a trip. i took the vehicle in to the dealership and they cleaned the throttle body. it ran ok for about 2 weeks and then became worse than it was before. i took it back to the dealership and they replaced the throttle body. so now time will tell. i was/am concerned about the fact i might not have been so lucky to be able to get off of the road and could have been in an accident. i have seen that this is a common occurrence in the 2010 ford fusion. i have contacted ford motor company as well to no avail. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 48000 miles. Vehicle Identification Number (VIN):3FAHPOJA5AR. Ford Fusion 2010 problem was reported in SOUTH BOSTON, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10465231

FORD FUSION 2010 car safety problem was reported on June 13, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . i and my children were traveling down the highway at 60 mph and i all of a sudden i could not give the car any gas. the motor was still running but i had no control over the gas. so i coasted until i could pull over. as i slowed down, the car shuttered. i turned the car off and restarted it. it ran fine for awhile. then it happened again and again (as i was entering an intersection, turning onto a major highway, and rounding a curve) until it was happening 3-4 times in a trip. i took the vehicle in to the dealership and they cleaned the throttle body. it ran ok for about 2 weeks and then became worse than it was before. i took it back to the dealership and they replaced the throttle body. so now time will tell. i was/am concerned about the fact i might not have been so lucky to be able to get off of the road and could have been in an accident. i have seen that this is a common occurrence in the 2010 ford fusion. i have contacted ford motor company as well to no avail. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 48000 miles. Vehicle Identification Number (VIN):3FAHPOJA5AR. Ford Fusion 2010 problem was reported in SOUTH BOSTON, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10465231

FORD FUSION 2010 car safety problem was reported on June 13, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . i and my children were traveling down the highway at 60 mph and i all of a sudden i could not give the car any gas. the motor was still running but i had no control over the gas. so i coasted until i could pull over. as i slowed down, the car shuttered. i turned the car off and restarted it. it ran fine for awhile. then it happened again and again (as i was entering an intersection, turning onto a major highway, and rounding a curve) until it was happening 3-4 times in a trip. i took the vehicle in to the dealership and they cleaned the throttle body. it ran ok for about 2 weeks and then became worse than it was before. i took it back to the dealership and they replaced the throttle body. so now time will tell. i was/am concerned about the fact i might not have been so lucky to be able to get off of the road and could have been in an accident. i have seen that this is a common occurrence in the 2010 ford fusion. i have contacted ford motor company as well to no avail. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 48000 miles. Vehicle Identification Number (VIN):3FAHPOJA5AR. Ford Fusion 2010 problem was reported in SOUTH BOSTON, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10465378

FORD FUSION 2010 car safety problem was reported on May 22, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while driving the car stalled out, went into safe mode, and had to coast off the road. happened several more times and took the car to the repair shop. mechanic diagnosed a faulty throttle body assembly and attempted to clean it. afterwards the car stalled again and the mechanic replaced the throttle body. just purchased a used mercury milan with 31,600 miles on and had the exact same problem occur. ford evidently has an issue with throttle body assemblies on these model of cars that can cause accidents. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 87000 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in CASSELBERRY, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10465378

FORD FUSION 2010 car safety problem was reported on May 22, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . while driving the car stalled out, went into safe mode, and had to coast off the road. happened several more times and took the car to the repair shop. mechanic diagnosed a faulty throttle body assembly and attempted to clean it. afterwards the car stalled again and the mechanic replaced the throttle body. just purchased a used mercury milan with 31,600 miles on and had the exact same problem occur. ford evidently has an issue with throttle body assemblies on these model of cars that can cause accidents. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 87000 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in CASSELBERRY, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10465589

FORD FUSION 2010 car safety problem was reported on June 19, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . on june 19, 2012, driving at approximately 40 mph, the car does not respond to pressing gas pedal, and it slows to a stop; everything else seems to continue to work fine. turned car off, then restarted it with no issues. on july 7, 2012, again driving at about 40-45 mph, the car starts to jerk, the gas pedal doesn't work, and the car starts to slow, while jerking, and a wrench/tool symbol appears on the dashboard. i pulled over, turned the car off, then turned it back on. i made it about 1 mile (close to home) and the car loses power in the same manner, jerking and slowing, gas pedal doesn't work, and the wrench light and the engine light both come on. i was able to roll down the road into my driveway. final incident with the same issues occurred on july 9, 2012. i called ford (car was still under warranty), and they said it was the throttle body, and the throttle body was replaced. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 22000 miles. Ford Fusion 2010 problem was reported in VERO BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10465589

FORD FUSION 2010 car safety problem was reported on June 19, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . on june 19, 2012, driving at approximately 40 mph, the car does not respond to pressing gas pedal, and it slows to a stop; everything else seems to continue to work fine. turned car off, then restarted it with no issues. on july 7, 2012, again driving at about 40-45 mph, the car starts to jerk, the gas pedal doesn't work, and the car starts to slow, while jerking, and a wrench/tool symbol appears on the dashboard. i pulled over, turned the car off, then turned it back on. i made it about 1 mile (close to home) and the car loses power in the same manner, jerking and slowing, gas pedal doesn't work, and the wrench light and the engine light both come on. i was able to roll down the road into my driveway. final incident with the same issues occurred on july 9, 2012. i called ford (car was still under warranty), and they said it was the throttle body, and the throttle body was replaced. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 22000 miles. Ford Fusion 2010 problem was reported in VERO BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10465617

FORD FUSION 2010 car safety problem was reported on June 15, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . i will never buy a ford vehicle again. my 2010 fusion is currently in the shop. it has been hesitating like there was water in the gas. we ruled that out. we checked transmission fluid, it was a little low so we added some. a little better but did not fix it. we were traveling on a major interstate when we had to coast to the shoulder when it would not pull anymore. check engine light came on. after sitting idle it finally leveled out and light went off but still was hesitating. the light continued to go off and on the remainder of the drive. when we reached our destination we located a ford dealership. they kept our car for a couple of hours and called us and said it reported a misfire code but that was all and that we needed to change the spark plugs. so we picked our car up and drove it back home to our regular dealership. our dealership kept it for 1 day and said the same thing, misfire code and to change the spark plugs and swap the coils around. so we did. didn't fix it. brought it back to our dealership where they kept it for exactly 2 weeks with no results. said they could not get it to do anything for them and if it started back to bring it back. 2 hours later we were back at the dealership. that was 3 days ago and still no explanation. they are stumped!!! so where does that leave me? with a $400.00 note on a car that is in the shop. ford needs to accept some responsibility. it's no coincidence everyone is having pretty much the same issues. *tr.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in COUSHATTA, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Ford Fusion 2010 Engine Review #10465654

FORD FUSION 2010 car safety problem was reported on July 14, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . 2010 ford fusion/just bought it in february 2012. this is the first problem i have had. i was going to work on i-40 and was setting the cruise at approx. 60-62 mph and all the sudden it jerked a little and stalled/when i depressed the gas it didn't do anything. the speed kept dropping....i had to cross over three very busy lanes of early morning commuter traffic and was scared someone would hit me before i could make it to the side of the road. i had to cut the car off and re start. drove off to work with no problems that day. after researching on the internet i see where numerous people have had this same problem with the ford fusion and have feared for their safety driving the vehicle. mechanics have said it is the throttle body and that ford has had to replace numerous of these. if this is a known problem there should be a recall before someone is seriously hurt if not killed. thank you! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 49000 miles. Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in WINSTON SALEM, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10465707

FORD FUSION 2010 car safety problem was reported on July 04, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . on multiple occasions the car will just lose all throttle response, the car is still running, but will not accelerate. i have to find some place to pull over and shut the car off. then restart the engine and then it will run good. the issue happens sometimes up six times in one day, and then you can go a week without an issue. i have seen this issue with speeds as low as 20 mph all the way up to 70 mph. from what i have read online it would appear to possibly be due to a defective throttle body. apparently this throttle body uses a servo to open and close the butterfly that allows air into the intake manifold. i feel this could be a very dangerous problem especially if you are driving and it loses the ability to accelerate and you can not find a safe place to pull over to restart the car. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 57000 miles. Vehicle Identification Number (VIN):3FAHP0HG8AR. Ford Fusion 2010 problem was reported in WEDGEFIELD, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10465707

FORD FUSION 2010 car safety problem was reported on July 04, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . on multiple occasions the car will just lose all throttle response, the car is still running, but will not accelerate. i have to find some place to pull over and shut the car off. then restart the engine and then it will run good. the issue happens sometimes up six times in one day, and then you can go a week without an issue. i have seen this issue with speeds as low as 20 mph all the way up to 70 mph. from what i have read online it would appear to possibly be due to a defective throttle body. apparently this throttle body uses a servo to open and close the butterfly that allows air into the intake manifold. i feel this could be a very dangerous problem especially if you are driving and it loses the ability to accelerate and you can not find a safe place to pull over to restart the car. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 57000 miles. Vehicle Identification Number (VIN):3FAHP0HG8AR. Ford Fusion 2010 problem was reported in WEDGEFIELD, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10465707

FORD FUSION 2010 car safety problem was reported on July 04, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . on multiple occasions the car will just lose all throttle response, the car is still running, but will not accelerate. i have to find some place to pull over and shut the car off. then restart the engine and then it will run good. the issue happens sometimes up six times in one day, and then you can go a week without an issue. i have seen this issue with speeds as low as 20 mph all the way up to 70 mph. from what i have read online it would appear to possibly be due to a defective throttle body. apparently this throttle body uses a servo to open and close the butterfly that allows air into the intake manifold. i feel this could be a very dangerous problem especially if you are driving and it loses the ability to accelerate and you can not find a safe place to pull over to restart the car. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 57000 miles. Vehicle Identification Number (VIN):3FAHP0HG8AR. Ford Fusion 2010 problem was reported in WEDGEFIELD, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10465707

FORD FUSION 2010 car safety problem was reported on July 04, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . on multiple occasions the car will just lose all throttle response, the car is still running, but will not accelerate. i have to find some place to pull over and shut the car off. then restart the engine and then it will run good. the issue happens sometimes up six times in one day, and then you can go a week without an issue. i have seen this issue with speeds as low as 20 mph all the way up to 70 mph. from what i have read online it would appear to possibly be due to a defective throttle body. apparently this throttle body uses a servo to open and close the butterfly that allows air into the intake manifold. i feel this could be a very dangerous problem especially if you are driving and it loses the ability to accelerate and you can not find a safe place to pull over to restart the car. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 57000 miles. Vehicle Identification Number (VIN):3FAHP0HG8AR. Ford Fusion 2010 problem was reported in WEDGEFIELD, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10465747

FORD FUSION 2010 car safety problem was reported on June 18, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i was merging into traffic onto a major interstate on my way to work at approximately 55 to 60 mph and my 2010 ford fusion lost all power. i was able to get the car off to the side of the interstate. i cut the motor off. i started the engine back and proceeded to work. did not contact the dealership on the first incident. two days later i was coming home and had just crossed over a two lane highway to get to the road i live on and had the same issue, the car lost all power and there was a jerking in the transmission. i was able to get the car off the road again, from previous experience i turned the car off and let it set for a couple of minutes and restarted the car. we then called the dealership and were advised to bring the car in. they had the car for 2 days and they said they could not get a code and they reprogrammed the computer. we drove the car for 3 days and while traveling on the interstate again at approx. 70 mph in the fast lane with a tractor and trailer behind me the car proceeded again to lose power. the tractor and trailer had to apply his brakes to keep from hitting me in the back. i finally was able to get the car off into the center median. again we cut the motor off and started it again and was able to make it home. we called the dealership the next day and were advised to bring it in again. they had the car for 2 weeks. they finally called us and said they thought it was the throttle body. we called ford motor company and naturally they told us there was no recall and they could not help us with the cost of the throttle body. what is it going to take for ford to do a recall?? death!! i have read approximately 70 complaints on the same issue on the 2010 fusions. i have grandchildren that frequently ride with me, does ford not care about the lives that could be taken due to this issue or are they making so much money on this that they don't care. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 45600 miles. Ford Fusion 2010 problem was reported in STATE ROAD, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10465753

FORD FUSION 2010 car safety problem was reported on July 13, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . i was traveling on the freeway at 65 mph. i heard a thump, the wrench lite came on and then i lost acceleration power. i had to coast off the freeway and come to a stop. i still had steering and brakes but no power. i had car towed to the ford dealer who replaced the throttle body assembly. i have read so many of these reports and i feel, like the others, that it is only a matter of time before someone is hurt or killed! ford needs to get on the ball and make this a recall. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 78637 miles. Vehicle Identification Number (VIN):3FAHPOGA9AR. Ford Fusion 2010 problem was reported in MONROVIA, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10465753

FORD FUSION 2010 car safety problem was reported on July 13, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i was traveling on the freeway at 65 mph. i heard a thump, the wrench lite came on and then i lost acceleration power. i had to coast off the freeway and come to a stop. i still had steering and brakes but no power. i had car towed to the ford dealer who replaced the throttle body assembly. i have read so many of these reports and i feel, like the others, that it is only a matter of time before someone is hurt or killed! ford needs to get on the ball and make this a recall. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 78637 miles. Vehicle Identification Number (VIN):3FAHPOGA9AR. Ford Fusion 2010 problem was reported in MONROVIA, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10465918

FORD FUSION 2010 car safety problem was reported on July 10, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . i was driving on a main street at 40 mph when my fusion suddenly lost power. i was able to pull over in a left turn lane. both the check engine light and the wrench light came on. i was able to restart the car and took back streets at a reduced speed in order to complete the remaining 3 miles to my home. i was able to drive the car to the nearest ford dealership the next morning. apparently, the problem is a defective throttle control. it was replaced for a price slightly less than $500. the replacement comes with a 12 month, 12,000 mile warranty. contacted ford customer service to vent my frustration on this expensive maintenance item. response from ford was very disappointing. my claim was denied since my car is less than 4,000 miles out of warranty. i was fortunate that this event did not occur on a highway and i was close to my home. searching the internet showed that this is a common failure with ford fusions. this is the first ford i have purchased and will be the last ford i will purchase. it seems shortsighted on the part of ford to ignore the value of quality and customer satisfaction. i have had my fusion in every three months for routine maintenance, but i see no point in continuing to pay a premium for service at a dealership when i know that ford will not stand behind their vehicles. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 39600 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in DALLAS, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10465918

FORD FUSION 2010 car safety problem was reported on July 10, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i was driving on a main street at 40 mph when my fusion suddenly lost power. i was able to pull over in a left turn lane. both the check engine light and the wrench light came on. i was able to restart the car and took back streets at a reduced speed in order to complete the remaining 3 miles to my home. i was able to drive the car to the nearest ford dealership the next morning. apparently, the problem is a defective throttle control. it was replaced for a price slightly less than $500. the replacement comes with a 12 month, 12,000 mile warranty. contacted ford customer service to vent my frustration on this expensive maintenance item. response from ford was very disappointing. my claim was denied since my car is less than 4,000 miles out of warranty. i was fortunate that this event did not occur on a highway and i was close to my home. searching the internet showed that this is a common failure with ford fusions. this is the first ford i have purchased and will be the last ford i will purchase. it seems shortsighted on the part of ford to ignore the value of quality and customer satisfaction. i have had my fusion in every three months for routine maintenance, but i see no point in continuing to pay a premium for service at a dealership when i know that ford will not stand behind their vehicles. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 39600 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in DALLAS, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Power Train Review #10465966

FORD FUSION 2010 car safety problem was reported on Oct 10, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . car shifts extremely hard into reverse--feels like transmission is going to drop out of the car. does not accelerate properly; feels like accelerating in a higher gear when starting off. does not seem to shift gears when driving. shifts hard when changing from reverse to drive. also feels like transmission drops randomly when driving at high and low speeds. car has been into the dealer on 4 separate occasions over 9 months and problem still isn't fixed. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 42875 miles. Vehicle Identification Number (VIN):3FAHP0HA5AR. Ford Fusion 2010 problem was reported in ROSEVILLE, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train Review #10465971

FORD FUSION 2010 car safety problem was reported on July 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . driving with the flow of traffic on a busy road, going about 55 all of sudden i lose power and the wrench light comes on. i was in the fast lane, and was very lucky to be able to get over to the slow lane, and eventually the shoulder and come to a stop. when i finally stopped, the car started shaking or hesitating. i turned the car off and sat for a few minutes. i then turned the car back on and everything was fine. the wrench light was gone and the car ran fine. this has happened 3 times and i have been very lucky that it has not caused a serious accident. i am going to take the car to the dealership on thursday, but seeing that so many other numerous people have had the same problem and ford just says that there is no problem, it will probably be a waste of time. it will most likely take a serious crash or death before ford will figure out what's really going on with these cars. sad, but true. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 53000 miles. Ford Fusion 2010 problem was reported in LA PLATA, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10466006

FORD FUSION 2010 car safety problem was reported on July 17, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . i accelerated away from a stop light and as i shifted from 2nd to 3rd gear the car jerked and i had no power at all the engine was still running, but when i put my foot into the accelerator nothing happened. also a wrench was displayed in the warning light area of the dash. i was able to coast to the side of the road and turned the car off. when i restarted it about 15 seconds later the wrench was gone and the car seemed fine. i am reporting this because i see that it is happening to a large number of 2010 fusion owners with similar mileage and it can be a real safety issue when your car dies in traffic! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 38560 miles. Ford Fusion 2010 problem was reported in CAMBRIDGE, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10466006

FORD FUSION 2010 car safety problem was reported on July 17, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i accelerated away from a stop light and as i shifted from 2nd to 3rd gear the car jerked and i had no power at all the engine was still running, but when i put my foot into the accelerator nothing happened. also a wrench was displayed in the warning light area of the dash. i was able to coast to the side of the road and turned the car off. when i restarted it about 15 seconds later the wrench was gone and the car seemed fine. i am reporting this because i see that it is happening to a large number of 2010 fusion owners with similar mileage and it can be a real safety issue when your car dies in traffic! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 38560 miles. Ford Fusion 2010 problem was reported in CAMBRIDGE, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10466006

FORD FUSION 2010 car safety problem was reported on July 17, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . i accelerated away from a stop light and as i shifted from 2nd to 3rd gear the car jerked and i had no power at all the engine was still running, but when i put my foot into the accelerator nothing happened. also a wrench was displayed in the warning light area of the dash. i was able to coast to the side of the road and turned the car off. when i restarted it about 15 seconds later the wrench was gone and the car seemed fine. i am reporting this because i see that it is happening to a large number of 2010 fusion owners with similar mileage and it can be a real safety issue when your car dies in traffic! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 38560 miles. Ford Fusion 2010 problem was reported in CAMBRIDGE, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10466305

FORD FUSION 2010 car safety problem was reported on June 25, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i was traveling at 60mph in morning rush hour traffic when the 2010 ford fusion lost acceleration. then the car started to chug so i pulled off onto the shoulder before the exit. it was not a full shoulder as the car was still occupying half of a lane. a ten-wheeler truck was right behind me and fortunately was able to stop.the car had to be towed to the dealership and the throttle body had to be replaced. this car is a safety hazard. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 30757 miles. Vehicle Identification Number (VIN):3FAHP0HGXAR. Ford Fusion 2010 problem was reported in SAINT CHARLES, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10466305

FORD FUSION 2010 car safety problem was reported on June 25, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . i was traveling at 60mph in morning rush hour traffic when the 2010 ford fusion lost acceleration. then the car started to chug so i pulled off onto the shoulder before the exit. it was not a full shoulder as the car was still occupying half of a lane. a ten-wheeler truck was right behind me and fortunately was able to stop.the car had to be towed to the dealership and the throttle body had to be replaced. this car is a safety hazard. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 30757 miles. Vehicle Identification Number (VIN):3FAHP0HGXAR. Ford Fusion 2010 problem was reported in SAINT CHARLES, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Engine Review #10466537

FORD FUSION 2010 car safety problem was reported on July 10, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . was driving out of a parking lot car suddenly stalled when accelerating. had to park and restart car to reengage engine. wrench and engine lights came on. car stalled out three more times going around the block. diag code was p0455. dealer initially replaced purge valve. on way home from dealership repair, engine cut out going 70 on highway. returned car to dealer. diag code was p2112. dealer replaced throttle body. car seems to be running normally now. this was a scary problem and a huge possible safety hazard when the vehicle cuts out unexpectedly at random times. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 77200 miles. Vehicle Identification Number (VIN):3FAHP0HG5AR. Ford Fusion 2010 problem was reported in GRAND RAPIDS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10466537

FORD FUSION 2010 car safety problem was reported on July 10, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . was driving out of a parking lot car suddenly stalled when accelerating. had to park and restart car to reengage engine. wrench and engine lights came on. car stalled out three more times going around the block. diag code was p0455. dealer initially replaced purge valve. on way home from dealership repair, engine cut out going 70 on highway. returned car to dealer. diag code was p2112. dealer replaced throttle body. car seems to be running normally now. this was a scary problem and a huge possible safety hazard when the vehicle cuts out unexpectedly at random times. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 77200 miles. Vehicle Identification Number (VIN):3FAHP0HG5AR. Ford Fusion 2010 problem was reported in GRAND RAPIDS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10466537

FORD FUSION 2010 car safety problem was reported on July 10, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . was driving out of a parking lot car suddenly stalled when accelerating. had to park and restart car to reengage engine. wrench and engine lights came on. car stalled out three more times going around the block. diag code was p0455. dealer initially replaced purge valve. on way home from dealership repair, engine cut out going 70 on highway. returned car to dealer. diag code was p2112. dealer replaced throttle body. car seems to be running normally now. this was a scary problem and a huge possible safety hazard when the vehicle cuts out unexpectedly at random times. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 77200 miles. Vehicle Identification Number (VIN):3FAHP0HG5AR. Ford Fusion 2010 problem was reported in GRAND RAPIDS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Fuel/propulsion System Review #10466629

FORD FUSION 2010 car safety problem was reported on July 19, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . the vehicle went into limited power mode (limp mode) while driving on the highway at fast speeds and low speeds. the vehicle refused to accelerate and almost cause a fatal accident. i suspect that a faulty throttle body is the problem. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 82000 miles. Vehicle Identification Number (VIN):3FAHP0JA5AR. Ford Fusion 2010 problem was reported in FORT WAYNE, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 75 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10466629

FORD FUSION 2010 car safety problem was reported on July 19, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . the vehicle went into limited power mode (limp mode) while driving on the highway at fast speeds and low speeds. the vehicle refused to accelerate and almost cause a fatal accident. i suspect that a faulty throttle body is the problem. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 82000 miles. Vehicle Identification Number (VIN):3FAHP0JA5AR. Ford Fusion 2010 problem was reported in FORT WAYNE, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 75 mph.

Ford Fusion 2010 Power Train Review #10466712

FORD FUSION 2010 car safety problem was reported on July 16, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . while driving on the highway at 70 mph my car cuts off. i merge to the side of the road and after a few minutes it restarts. i put it in drive and continue driving. the next morning it does the same thing. when it looses power the wrench light, check engine light, and traction control lights come on and it says service advancetrac in the service bar on the dash panel. i have taken it to ford several times and there are no codes stored for them to go by. they made me a new key and stated they thought it was my key going bad. i am sure that it is something more as it has done it again even with the new key. there is definitely something going on with the throttle bodies on these cars. it is very scary and unsafe when the car loses power in rush hour traffic. i have 3 children that i transport in this car everyday. i honestly hope ford investigates this and fixes the problem. i also had the problem with the lug nuts and wheel studs snapping off. there is a recall for that but i was told my car did not fall under that recall even though it was having the same issues? this is the first ford i have ever owned and i will never buy another one. not just the quality of the vehicle, but the tech's at the shops don't know anything, and ford does not stand behind their products!! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 98000 miles. Ford Fusion 2010 problem was reported in CHARLOTTESVILLE, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Traction Control System

Ford Fusion 2010 Traction Control System Review #10466712

FORD FUSION 2010 car safety problem was reported on July 16, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with TRACTION CONTROL SYSTEM . while driving on the highway at 70 mph my car cuts off. i merge to the side of the road and after a few minutes it restarts. i put it in drive and continue driving. the next morning it does the same thing. when it looses power the wrench light, check engine light, and traction control lights come on and it says service advancetrac in the service bar on the dash panel. i have taken it to ford several times and there are no codes stored for them to go by. they made me a new key and stated they thought it was my key going bad. i am sure that it is something more as it has done it again even with the new key. there is definitely something going on with the throttle bodies on these cars. it is very scary and unsafe when the car loses power in rush hour traffic. i have 3 children that i transport in this car everyday. i honestly hope ford investigates this and fixes the problem. i also had the problem with the lug nuts and wheel studs snapping off. there is a recall for that but i was told my car did not fall under that recall even though it was having the same issues? this is the first ford i have ever owned and i will never buy another one. not just the quality of the vehicle, but the tech's at the shops don't know anything, and ford does not stand behind their products!! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 98000 miles. Ford Fusion 2010 problem was reported in CHARLOTTESVILLE, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10466712

FORD FUSION 2010 car safety problem was reported on July 16, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . while driving on the highway at 70 mph my car cuts off. i merge to the side of the road and after a few minutes it restarts. i put it in drive and continue driving. the next morning it does the same thing. when it looses power the wrench light, check engine light, and traction control lights come on and it says service advancetrac in the service bar on the dash panel. i have taken it to ford several times and there are no codes stored for them to go by. they made me a new key and stated they thought it was my key going bad. i am sure that it is something more as it has done it again even with the new key. there is definitely something going on with the throttle bodies on these cars. it is very scary and unsafe when the car loses power in rush hour traffic. i have 3 children that i transport in this car everyday. i honestly hope ford investigates this and fixes the problem. i also had the problem with the lug nuts and wheel studs snapping off. there is a recall for that but i was told my car did not fall under that recall even though it was having the same issues? this is the first ford i have ever owned and i will never buy another one. not just the quality of the vehicle, but the tech's at the shops don't know anything, and ford does not stand behind their products!! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 98000 miles. Ford Fusion 2010 problem was reported in CHARLOTTESVILLE, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10466729

FORD FUSION 2010 car safety problem was reported on July 14, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. while driving approximately 5 mph and entering a parking space, the vehicle accelerated rapidly as the contact slightly depressed the accelerator pedal. the contact applied the brakes but the vehicle would not respond. the contact crashed into a concrete pillar. the contact sustained bruising to the shoulder and breast plate from the seat belt. the vehicle sustained damage to the bumper. the vehicle was taken to the dealer for diagnostics where the technician stated that the transmission was loose but did not mention if the crash was related to the transmission. the vehicle was not repaired. the vin was not available. the approximate failure mileage was 46,000. .Vehicle was involved in a crash. 1 person(s) were injured. 0 person(s) died.Mileage was 46000 miles. Ford Fusion 2010 problem was reported in PHILADELPHIA, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 5 mph.

Ford Fusion 2010 Vehicle Speed Control Review #10466732

FORD FUSION 2010 car safety problem was reported on June 26, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact stated that while driving 55 mph, the throttle failed. the tachometer displayed 2,000 rpms however the vehicle was not responsive to acceleration attempts. the contact parked the vehicle and later, the failure was corrected however the failure recurred several times. the vehicle was not taken to the dealer or a repair shop for inspection or repairs. the manufacturer was not made aware of the failure. the current mileage was 60,506. the failure mileage was 59,000. .0 person(s) were injured. 0 person(s) died.Mileage was 59000 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in RICHMOND, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10466753

FORD FUSION 2010 car safety problem was reported on July 18, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . with no warning or other signs, the car stalled out. driving on a flat /straight road. pulled to the side of the road and restarted the car without issue. 3hrs later the same issue. two days after that my wife experienced the same issue. checking on the internet, this seems to be a re-occurring theme for the electronic throttle bodies of the ford fusion. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 52600 miles. Vehicle Identification Number (VIN):3FAHP0JA2AR. Ford Fusion 2010 problem was reported in RUSSELLVILLE, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10466753

FORD FUSION 2010 car safety problem was reported on July 18, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . with no warning or other signs, the car stalled out. driving on a flat /straight road. pulled to the side of the road and restarted the car without issue. 3hrs later the same issue. two days after that my wife experienced the same issue. checking on the internet, this seems to be a re-occurring theme for the electronic throttle bodies of the ford fusion. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 52600 miles. Vehicle Identification Number (VIN):3FAHP0JA2AR. Ford Fusion 2010 problem was reported in RUSSELLVILLE, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10467013

FORD FUSION 2010 car safety problem was reported on July 05, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . there is a serious problem with this car in that it will completely shut down while traveling at any speed whether 15 mph or 70 mph, with no warning. this could cause serious harm especially traveling on the interstate where you can be hit from behind at a high rate of speed. the car will restart after a few minutes, but when doing so will cancel the engine service code p2111 so that the dealer cannot id the problem. if you experience this problem, make them keep driving it until it happens to the service person. issue is defective throttle body -potentiometer. the computer can't tell how much the throttle is open so it shut down. my teenager was driving this car and was almost re-ended twice. very dangerous problem. car should be recalled for this issue!!!!! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 36200 miles. Vehicle Identification Number (VIN):3FAHP0HAXAR. Ford Fusion 2010 problem was reported in DAVIDSONVILLE, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10467013

FORD FUSION 2010 car safety problem was reported on July 05, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . there is a serious problem with this car in that it will completely shut down while traveling at any speed whether 15 mph or 70 mph, with no warning. this could cause serious harm especially traveling on the interstate where you can be hit from behind at a high rate of speed. the car will restart after a few minutes, but when doing so will cancel the engine service code p2111 so that the dealer cannot id the problem. if you experience this problem, make them keep driving it until it happens to the service person. issue is defective throttle body -potentiometer. the computer can't tell how much the throttle is open so it shut down. my teenager was driving this car and was almost re-ended twice. very dangerous problem. car should be recalled for this issue!!!!! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 36200 miles. Vehicle Identification Number (VIN):3FAHP0HAXAR. Ford Fusion 2010 problem was reported in DAVIDSONVILLE, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10467058

FORD FUSION 2010 car safety problem was reported on June 24, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . driving up to a red light that had just turned green, the wrench light came on in my 2010 ford fusion, it began to jerk, i lost all acceleration, and my gas pedal would not respond. i was able to limp the car into a parking lot where i turned the car off. i waited a minute or so and recranked it. it shook/sputtered a little bit, but eventually cranked and the wrench light was off. continued driving and it happened again a couple miles down the road at around 50 mph. again i was able to limp into a parking lot, kill the car, and recrank as before. took car to dealer the next day. they couldn't get an error code reading or replicate the problem. was told to come back with wrench light on (which is impossible because the car won't go when the light is on). i've had this problem occur 3 more times, have filed a complaint with ford, and my vehicle is currently at the dealership as they try to diagnose the problem again. i've read a ridiculous number of complaints about this issue online from other 2010 ford fusion owners. the problem is a bad throttle body, and it is going to get someone killed. i've been driving cautiously since it first occurred because i know i can't rely on the gas pedal to always respond, but for someone to whom it happens the first time who attempts to cross traffic and then finds himself a sitting duck in the middle of the road with oncoming traffic, it is going to spell tragedy. please hold ford responsible! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 58500 miles. Vehicle Identification Number (VIN):3FAHP0JG6AR. Ford Fusion 2010 problem was reported in CAMERON, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10467058

FORD FUSION 2010 car safety problem was reported on June 24, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . driving up to a red light that had just turned green, the wrench light came on in my 2010 ford fusion, it began to jerk, i lost all acceleration, and my gas pedal would not respond. i was able to limp the car into a parking lot where i turned the car off. i waited a minute or so and recranked it. it shook/sputtered a little bit, but eventually cranked and the wrench light was off. continued driving and it happened again a couple miles down the road at around 50 mph. again i was able to limp into a parking lot, kill the car, and recrank as before. took car to dealer the next day. they couldn't get an error code reading or replicate the problem. was told to come back with wrench light on (which is impossible because the car won't go when the light is on). i've had this problem occur 3 more times, have filed a complaint with ford, and my vehicle is currently at the dealership as they try to diagnose the problem again. i've read a ridiculous number of complaints about this issue online from other 2010 ford fusion owners. the problem is a bad throttle body, and it is going to get someone killed. i've been driving cautiously since it first occurred because i know i can't rely on the gas pedal to always respond, but for someone to whom it happens the first time who attempts to cross traffic and then finds himself a sitting duck in the middle of the road with oncoming traffic, it is going to spell tragedy. please hold ford responsible! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 58500 miles. Vehicle Identification Number (VIN):3FAHP0JG6AR. Ford Fusion 2010 problem was reported in CAMERON, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Power Train Review #10467171

FORD FUSION 2010 car safety problem was reported on July 22, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . driving at 65mph in traffic on a state highway when the vehicle failed to respond to the accelerator. vehicle went to approximately 750 rpm and there was no speed control. this failure occurred without any warning as i was passing another car and required me to take evasive action to avoid collision. dealership says it was throttle body control unit and that there are "known problems". *tr.0 person(s) were injured. 0 person(s) died.Mileage was 55652 miles. Vehicle Identification Number (VIN):3FAHP0JA9AR. Ford Fusion 2010 problem was reported in EAGAN, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10467171

FORD FUSION 2010 car safety problem was reported on July 22, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . driving at 65mph in traffic on a state highway when the vehicle failed to respond to the accelerator. vehicle went to approximately 750 rpm and there was no speed control. this failure occurred without any warning as i was passing another car and required me to take evasive action to avoid collision. dealership says it was throttle body control unit and that there are "known problems". *tr.0 person(s) were injured. 0 person(s) died.Mileage was 55652 miles. Vehicle Identification Number (VIN):3FAHP0JA9AR. Ford Fusion 2010 problem was reported in EAGAN, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10467171

FORD FUSION 2010 car safety problem was reported on July 22, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . driving at 65mph in traffic on a state highway when the vehicle failed to respond to the accelerator. vehicle went to approximately 750 rpm and there was no speed control. this failure occurred without any warning as i was passing another car and required me to take evasive action to avoid collision. dealership says it was throttle body control unit and that there are "known problems". *tr.0 person(s) were injured. 0 person(s) died.Mileage was 55652 miles. Vehicle Identification Number (VIN):3FAHP0JA9AR. Ford Fusion 2010 problem was reported in EAGAN, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10467187

FORD FUSION 2010 car safety problem was reported on July 22, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . on 7/22/2012 at approximately 2000 hours my family was traveling southbound on georgia state route 3 - us hwy. 41 in rocky face, georgia when our vehicle (2010 ford fusion automatic transmission) suddenly without notice went from a solid cruising speed of 40mph to an abrupt halt - nose of the car actually went forward towards the ground so abruptly that it made contact with the ground. the vehicle stalled (still barely running) in the lane of travel and would not get any throttle acceleration. my family and vehicle was almost struck by on coming motorists from the rear due to the abrupt stopping and the vehicle would barely get any throttle acceleration. after the georgia state patrol trooper came to assist the car would not go above 25 mph without suddenly stalling and the check engine light coming on along with an orange wrench symbol. the vehicle had to be abandoned at the dalton georgia state patrol post due to this issue until ford could send a representative to tow the vehicle to the local dealer where we purchased. the local dealer on 7/23/12 informed us that this is an on-going problem that ford is aware of and that the "throttle body" would have to be replaced. upon further online investigation i found that this issue is widespread and reported since 2010 & has caused very unsafe conditions for motorists such as it did with my family. i am asking you all to look into recalling the "throttle body" on the 2010 ford fusions to be replaced. this is a problem that ford is aware of and they are blatantly passing the blame off onto the consumer and someone (if not my own family) is going to get hurt. it is unsafe for a late model vehicle that has been serviced as required by the manufacture every 3-5 months to have these abrupt issues and break my family down in the roadway of travel on a major us highway. nhtsa please have ford correct before someone gets injured!! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 39500 miles. Vehicle Identification Number (VIN):3FAHP0JA7AR. Ford Fusion 2010 problem was reported in TUNNEL HILL, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10467187

FORD FUSION 2010 car safety problem was reported on July 22, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . on 7/22/2012 at approximately 2000 hours my family was traveling southbound on georgia state route 3 - us hwy. 41 in rocky face, georgia when our vehicle (2010 ford fusion automatic transmission) suddenly without notice went from a solid cruising speed of 40mph to an abrupt halt - nose of the car actually went forward towards the ground so abruptly that it made contact with the ground. the vehicle stalled (still barely running) in the lane of travel and would not get any throttle acceleration. my family and vehicle was almost struck by on coming motorists from the rear due to the abrupt stopping and the vehicle would barely get any throttle acceleration. after the georgia state patrol trooper came to assist the car would not go above 25 mph without suddenly stalling and the check engine light coming on along with an orange wrench symbol. the vehicle had to be abandoned at the dalton georgia state patrol post due to this issue until ford could send a representative to tow the vehicle to the local dealer where we purchased. the local dealer on 7/23/12 informed us that this is an on-going problem that ford is aware of and that the "throttle body" would have to be replaced. upon further online investigation i found that this issue is widespread and reported since 2010 & has caused very unsafe conditions for motorists such as it did with my family. i am asking you all to look into recalling the "throttle body" on the 2010 ford fusions to be replaced. this is a problem that ford is aware of and they are blatantly passing the blame off onto the consumer and someone (if not my own family) is going to get hurt. it is unsafe for a late model vehicle that has been serviced as required by the manufacture every 3-5 months to have these abrupt issues and break my family down in the roadway of travel on a major us highway. nhtsa please have ford correct before someone gets injured!! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 39500 miles. Vehicle Identification Number (VIN):3FAHP0JA7AR. Ford Fusion 2010 problem was reported in TUNNEL HILL, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10467187

FORD FUSION 2010 car safety problem was reported on July 22, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . on 7/22/2012 at approximately 2000 hours my family was traveling southbound on georgia state route 3 - us hwy. 41 in rocky face, georgia when our vehicle (2010 ford fusion automatic transmission) suddenly without notice went from a solid cruising speed of 40mph to an abrupt halt - nose of the car actually went forward towards the ground so abruptly that it made contact with the ground. the vehicle stalled (still barely running) in the lane of travel and would not get any throttle acceleration. my family and vehicle was almost struck by on coming motorists from the rear due to the abrupt stopping and the vehicle would barely get any throttle acceleration. after the georgia state patrol trooper came to assist the car would not go above 25 mph without suddenly stalling and the check engine light coming on along with an orange wrench symbol. the vehicle had to be abandoned at the dalton georgia state patrol post due to this issue until ford could send a representative to tow the vehicle to the local dealer where we purchased. the local dealer on 7/23/12 informed us that this is an on-going problem that ford is aware of and that the "throttle body" would have to be replaced. upon further online investigation i found that this issue is widespread and reported since 2010 & has caused very unsafe conditions for motorists such as it did with my family. i am asking you all to look into recalling the "throttle body" on the 2010 ford fusions to be replaced. this is a problem that ford is aware of and they are blatantly passing the blame off onto the consumer and someone (if not my own family) is going to get hurt. it is unsafe for a late model vehicle that has been serviced as required by the manufacture every 3-5 months to have these abrupt issues and break my family down in the roadway of travel on a major us highway. nhtsa please have ford correct before someone gets injured!! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 39500 miles. Vehicle Identification Number (VIN):3FAHP0JA7AR. Ford Fusion 2010 problem was reported in TUNNEL HILL, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10467187

FORD FUSION 2010 car safety problem was reported on July 22, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . on 7/22/2012 at approximately 2000 hours my family was traveling southbound on georgia state route 3 - us hwy. 41 in rocky face, georgia when our vehicle (2010 ford fusion automatic transmission) suddenly without notice went from a solid cruising speed of 40mph to an abrupt halt - nose of the car actually went forward towards the ground so abruptly that it made contact with the ground. the vehicle stalled (still barely running) in the lane of travel and would not get any throttle acceleration. my family and vehicle was almost struck by on coming motorists from the rear due to the abrupt stopping and the vehicle would barely get any throttle acceleration. after the georgia state patrol trooper came to assist the car would not go above 25 mph without suddenly stalling and the check engine light coming on along with an orange wrench symbol. the vehicle had to be abandoned at the dalton georgia state patrol post due to this issue until ford could send a representative to tow the vehicle to the local dealer where we purchased. the local dealer on 7/23/12 informed us that this is an on-going problem that ford is aware of and that the "throttle body" would have to be replaced. upon further online investigation i found that this issue is widespread and reported since 2010 & has caused very unsafe conditions for motorists such as it did with my family. i am asking you all to look into recalling the "throttle body" on the 2010 ford fusions to be replaced. this is a problem that ford is aware of and they are blatantly passing the blame off onto the consumer and someone (if not my own family) is going to get hurt. it is unsafe for a late model vehicle that has been serviced as required by the manufacture every 3-5 months to have these abrupt issues and break my family down in the roadway of travel on a major us highway. nhtsa please have ford correct before someone gets injured!! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 39500 miles. Vehicle Identification Number (VIN):3FAHP0JA7AR. Ford Fusion 2010 problem was reported in TUNNEL HILL, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10467223

FORD FUSION 2010 car safety problem was reported on July 22, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . was driving on at 65mph on a state highway and passing another vehicle when my vehicle suddenly stopped responding to the accelerator. the engine dropped to 750 rpm and wouldn't do anything in response to my attempts to accelerate. the vehicle slowed quite rapidly because of this problem and i had to take evasive action to avoid a crash. there was no warning prior to it happening and no sounds associated with the incident. if my wife had been driving i know there would have been an accident. after turning off the vehicle and restarting it, the vehicle drove properly. when i returned home, i checked for any codes and found there were none. took the vehicle to the dealer for repair and was told "it is probably the throttle body control; we know there have been many incidents like this". this was reported yesterday in another incident but not with "speed control" as the affected part. i did not know it was an option at that time. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 55650 miles. Vehicle Identification Number (VIN):3FAHP0JA9AR. Ford Fusion 2010 problem was reported in EAGAN, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10467223

FORD FUSION 2010 car safety problem was reported on July 22, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . was driving on at 65mph on a state highway and passing another vehicle when my vehicle suddenly stopped responding to the accelerator. the engine dropped to 750 rpm and wouldn't do anything in response to my attempts to accelerate. the vehicle slowed quite rapidly because of this problem and i had to take evasive action to avoid a crash. there was no warning prior to it happening and no sounds associated with the incident. if my wife had been driving i know there would have been an accident. after turning off the vehicle and restarting it, the vehicle drove properly. when i returned home, i checked for any codes and found there were none. took the vehicle to the dealer for repair and was told "it is probably the throttle body control; we know there have been many incidents like this". this was reported yesterday in another incident but not with "speed control" as the affected part. i did not know it was an option at that time. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 55650 miles. Vehicle Identification Number (VIN):3FAHP0JA9AR. Ford Fusion 2010 problem was reported in EAGAN, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10467656

FORD FUSION 2010 car safety problem was reported on July 23, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . while traveling on the expressway with the cruise control on my engine returned to idle speed and there was no response from the accelerator pedal. i had to coast to a stop on the shoulder, put the car in park, shut it off, and restart it. the next day this happened again twice, the check engine light came on, i read the code and it was p2112 throttle actuator control system stuck shut. i did some research and there are apparently some known problems with the throttle body assembly. my car is out of warranty and the dealer told me this part isn't covered under the extended emissions warranty. i was lucky that this didn't happen while i was turning or merging into traffic. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 63000 miles. Vehicle Identification Number (VIN):3FAHP0JG5AR. Ford Fusion 2010 problem was reported in GRAND RAPIDS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 75 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10467656

FORD FUSION 2010 car safety problem was reported on July 23, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . while traveling on the expressway with the cruise control on my engine returned to idle speed and there was no response from the accelerator pedal. i had to coast to a stop on the shoulder, put the car in park, shut it off, and restart it. the next day this happened again twice, the check engine light came on, i read the code and it was p2112 throttle actuator control system stuck shut. i did some research and there are apparently some known problems with the throttle body assembly. my car is out of warranty and the dealer told me this part isn't covered under the extended emissions warranty. i was lucky that this didn't happen while i was turning or merging into traffic. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 63000 miles. Vehicle Identification Number (VIN):3FAHP0JG5AR. Ford Fusion 2010 problem was reported in GRAND RAPIDS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 75 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10467656

FORD FUSION 2010 car safety problem was reported on July 23, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . while traveling on the expressway with the cruise control on my engine returned to idle speed and there was no response from the accelerator pedal. i had to coast to a stop on the shoulder, put the car in park, shut it off, and restart it. the next day this happened again twice, the check engine light came on, i read the code and it was p2112 throttle actuator control system stuck shut. i did some research and there are apparently some known problems with the throttle body assembly. my car is out of warranty and the dealer told me this part isn't covered under the extended emissions warranty. i was lucky that this didn't happen while i was turning or merging into traffic. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 63000 miles. Vehicle Identification Number (VIN):3FAHP0JG5AR. Ford Fusion 2010 problem was reported in GRAND RAPIDS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 75 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10467656

FORD FUSION 2010 car safety problem was reported on July 23, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . while traveling on the expressway with the cruise control on my engine returned to idle speed and there was no response from the accelerator pedal. i had to coast to a stop on the shoulder, put the car in park, shut it off, and restart it. the next day this happened again twice, the check engine light came on, i read the code and it was p2112 throttle actuator control system stuck shut. i did some research and there are apparently some known problems with the throttle body assembly. my car is out of warranty and the dealer told me this part isn't covered under the extended emissions warranty. i was lucky that this didn't happen while i was turning or merging into traffic. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 63000 miles. Vehicle Identification Number (VIN):3FAHP0JG5AR. Ford Fusion 2010 problem was reported in GRAND RAPIDS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 75 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10467688

FORD FUSION 2010 car safety problem was reported on July 19, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . i was driving on a busy highway going about 70 mph and all of a sudden i had no gas peddle. i had my 3 year old daughter in the car at the time. i had no clue what was going on and almost got hit from behind bc i had not touched my brake yet. i pulled over and my car did restart but i did not make it far before it did it again. i took got my car to the dealership and they told me the throttle body needed to be replaced. my car has 40,000 miles i got it brand new off the lot and it's not covered in the extended warranty. the dealership acted like it was no big deal. let me drive off the lot. they also wanted 250 more to repair it. looking online i'm finding out that this is happening to so many people. ford needs to have a recall on this part before someone does in an accident. i called ford myself and filed a formal complaint. please everyone must do the same that is the only way to prevent this from happening to someone else. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Ford Fusion 2010 problem was reported in DERBY, KS. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10467688

FORD FUSION 2010 car safety problem was reported on July 19, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . i was driving on a busy highway going about 70 mph and all of a sudden i had no gas peddle. i had my 3 year old daughter in the car at the time. i had no clue what was going on and almost got hit from behind bc i had not touched my brake yet. i pulled over and my car did restart but i did not make it far before it did it again. i took got my car to the dealership and they told me the throttle body needed to be replaced. my car has 40,000 miles i got it brand new off the lot and it's not covered in the extended warranty. the dealership acted like it was no big deal. let me drive off the lot. they also wanted 250 more to repair it. looking online i'm finding out that this is happening to so many people. ford needs to have a recall on this part before someone does in an accident. i called ford myself and filed a formal complaint. please everyone must do the same that is the only way to prevent this from happening to someone else. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Ford Fusion 2010 problem was reported in DERBY, KS. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10467777

FORD FUSION 2010 car safety problem was reported on Jan 12, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . tl* the contact owns a 2010 ford fusion. the contact stated that the vehicle was repaired under nhtsa campaign id number: 11v574000 (wheels:lugs/nuts/bolts) however the lug nut studs fractured after the recall repair was performed on both front wheels. the dealer and manufacturer refused to replace the lug nut studs because the remedy was not included in the recall defect. the contact stated that the defective lug nuts caused five lug nut studs to fracture, which were replaced by the dealer at the owner's expense. the approximate failure mileage was 43,448. .0 person(s) were injured. 0 person(s) died.Mileage was 43448 miles. Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in GREENFIELD, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10467979

FORD FUSION 2010 car safety problem was reported on July 25, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . actuator control system: throttle plate stuck open - vehicle shut down on freeway would not start only after 5 min wait then happened again 10 min later stopped again waited 5 more min next morning car started fine then after a few mins of driving stopped again having trouble staying on... *tr.0 person(s) were injured. 0 person(s) died.Mileage was 66000 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in HOUSTON, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10467979

FORD FUSION 2010 car safety problem was reported on July 25, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . actuator control system: throttle plate stuck open - vehicle shut down on freeway would not start only after 5 min wait then happened again 10 min later stopped again waited 5 more min next morning car started fine then after a few mins of driving stopped again having trouble staying on... *tr.0 person(s) were injured. 0 person(s) died.Mileage was 66000 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in HOUSTON, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10467979

FORD FUSION 2010 car safety problem was reported on July 25, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . actuator control system: throttle plate stuck open - vehicle shut down on freeway would not start only after 5 min wait then happened again 10 min later stopped again waited 5 more min next morning car started fine then after a few mins of driving stopped again having trouble staying on... *tr.0 person(s) were injured. 0 person(s) died.Mileage was 66000 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in HOUSTON, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10467987

FORD FUSION 2010 car safety problem was reported on July 24, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . the vehicle lost all power at 70 mph and a wrench light came on. this was very, very dangerous. i pulled to the side of the road and turned the vehicle off as it would not move forward anyway. it had a rough restart, but then seemed to be better though still running rough. the wrench light went out. it took it in for servicing at the dealer where they diagnosed the throttle body. this was a very scary and dangerous experience. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 54546 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in RICHFIELD, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10467987

FORD FUSION 2010 car safety problem was reported on July 24, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . the vehicle lost all power at 70 mph and a wrench light came on. this was very, very dangerous. i pulled to the side of the road and turned the vehicle off as it would not move forward anyway. it had a rough restart, but then seemed to be better though still running rough. the wrench light went out. it took it in for servicing at the dealer where they diagnosed the throttle body. this was a very scary and dangerous experience. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 54546 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in RICHFIELD, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10467987

FORD FUSION 2010 car safety problem was reported on July 24, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . the vehicle lost all power at 70 mph and a wrench light came on. this was very, very dangerous. i pulled to the side of the road and turned the vehicle off as it would not move forward anyway. it had a rough restart, but then seemed to be better though still running rough. the wrench light went out. it took it in for servicing at the dealer where they diagnosed the throttle body. this was a very scary and dangerous experience. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 54546 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in RICHFIELD, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Vehicle Speed Control Review #10468035

FORD FUSION 2010 car safety problem was reported on July 27, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . my 2010 ford fusion v6 sel surged, shook violently and stalled out. a light shaped like wrench appeared. i pulled over and let it rest for about 30 seconds, then tried to start. it started up and i drove home. after researching online, i found many, many other ford customers with my year vehicle were having the same problem. dealers were telling them it's a bad throttle body. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 52000 miles. Vehicle Identification Number (VIN):3FAHP0JG7AR. Ford Fusion 2010 problem was reported in CULPEPER, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10468035

FORD FUSION 2010 car safety problem was reported on July 27, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . my 2010 ford fusion v6 sel surged, shook violently and stalled out. a light shaped like wrench appeared. i pulled over and let it rest for about 30 seconds, then tried to start. it started up and i drove home. after researching online, i found many, many other ford customers with my year vehicle were having the same problem. dealers were telling them it's a bad throttle body. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 52000 miles. Vehicle Identification Number (VIN):3FAHP0JG7AR. Ford Fusion 2010 problem was reported in CULPEPER, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10468094

FORD FUSION 2010 car safety problem was reported on July 27, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i had just schedule to do my 75k maintenance on 7/27/12, which i did. the day before i had driven home from work and my car goes into low rpm's, and the throttle stops working but the car is still on! i immediately put on my hazards in rush hour traffic hoping i can find a shoulder in a construction zone. an 18 wheeler nearly knocked me off a bridge when i was drifting to safety at 15mph. i turned off the ignition as the car idles at 700 rpm's. i start it up again and i am able to drive. in two days it has happen once again, and now my average miles per gallon has gone down from 27.4mpg to 19/20 mpg!!! where is the recall...too common of an issue for a motor trend car of the year!!! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 73000 miles. Ford Fusion 2010 problem was reported in GARLAND, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10468094

FORD FUSION 2010 car safety problem was reported on July 27, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . i had just schedule to do my 75k maintenance on 7/27/12, which i did. the day before i had driven home from work and my car goes into low rpm's, and the throttle stops working but the car is still on! i immediately put on my hazards in rush hour traffic hoping i can find a shoulder in a construction zone. an 18 wheeler nearly knocked me off a bridge when i was drifting to safety at 15mph. i turned off the ignition as the car idles at 700 rpm's. i start it up again and i am able to drive. in two days it has happen once again, and now my average miles per gallon has gone down from 27.4mpg to 19/20 mpg!!! where is the recall...too common of an issue for a motor trend car of the year!!! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 73000 miles. Ford Fusion 2010 problem was reported in GARLAND, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10468096

FORD FUSION 2010 car safety problem was reported on June 15, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . on several occasions the car will not accelerate after stopping for a stop sign or light, then it jerks, moves forward and the rpm's rev up rapidly. then it resumes normally. i am concerned my vehicle has a faulty transmission or the throttle body issue that i have read about. i have only 17,000 miles on this car and will take it in for service, hopefully with resolution. i sure hope a recall is issued soon since this seems to be a serious safety issue. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 16500 miles. Vehicle Identification Number (VIN):3FAHP0HA9AR. Ford Fusion 2010 problem was reported in ALBUQUERQUE, NM. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Steering

Ford Fusion 2010 Steering Review #10468154

FORD FUSION 2010 car safety problem was reported on July 29, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with STEERING . was backing out of driveway and got a warning light that said the power steering needed serviced and then the steering got hard...im a grown man and it is so hard for me to drive and turn the wheels.this is my wife's car and im so thankful so wasn't driving it when this happened there's no way she could have controlled it.very bad design and a safety issue. *js.0 person(s) were injured. 0 person(s) died.Mileage was 172000 miles. Ford Fusion 2010 problem was reported in CUMMING, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 2 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10468171

FORD FUSION 2010 car safety problem was reported on July 10, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . driving home from work on the highway at approx. 55 mph, my car lost acceleration, the wrench light came on and my vehicle went into a limp mode. i was able to exit the highway and pull into a parking lot. after a couple of minutes, i was able to restart the car. it now ran as if nothing had happened and the wrench light was no longer on. i brought it to my ford dealer and they could not diagnose the problem as no codes remained. it happened again several days later. i called ford and was informed not to shut the vehicle off and restart it as this action cleared the vehicle of all diagnostic codes. i made another appt. with my dealer. the very next day it happened again. this time i did not shut the car off, but limped @ 5-6 mph to my dealer and showed them the wrench light and the fact that the vehicle was running rough and left the vehicle with them. i also told them not to restart it until they read the codes. after research on the web, i found that this problem is quite rampant in fords and has been a problem for several years. the problem is a defective throttle body. my dealer found the code that i gave them when they checked my car. i had to have it fixed as i need the car for work. ford refuses to acknowledge the problem. are they waiting for someone to get seriously injured or killed? they should stop putting the almighty dollar ahead of the lives of people. *js.0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Vehicle Identification Number (VIN):3FAHP0HG9AR. Ford Fusion 2010 problem was reported in MEDFORD, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: BIFUEL. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10468242

FORD FUSION 2010 car safety problem was reported on July 30, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . all of a sudden the rpm's immediately dropped to a rough idle. all throttle response was lost, i pulled over on the highway, where the vehicle was in limp mode with the check engine and wrench lights illuminated. the engine was idling very erratically and shaking, there was no response when pressing the accelerator. after shutting down the car, it restarted ok and drove. it suddenly did the same thing 2 more times before i was able to get home. the obd2 code was p2111, the drive by wire throttle bodies on these cars are faulty. seems to be a common problem. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 62107 miles. Ford Fusion 2010 problem was reported in CUMBERLAND, RI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10468242

FORD FUSION 2010 car safety problem was reported on July 30, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . all of a sudden the rpm's immediately dropped to a rough idle. all throttle response was lost, i pulled over on the highway, where the vehicle was in limp mode with the check engine and wrench lights illuminated. the engine was idling very erratically and shaking, there was no response when pressing the accelerator. after shutting down the car, it restarted ok and drove. it suddenly did the same thing 2 more times before i was able to get home. the obd2 code was p2111, the drive by wire throttle bodies on these cars are faulty. seems to be a common problem. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 62107 miles. Ford Fusion 2010 problem was reported in CUMBERLAND, RI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10468242

FORD FUSION 2010 car safety problem was reported on July 30, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . all of a sudden the rpm's immediately dropped to a rough idle. all throttle response was lost, i pulled over on the highway, where the vehicle was in limp mode with the check engine and wrench lights illuminated. the engine was idling very erratically and shaking, there was no response when pressing the accelerator. after shutting down the car, it restarted ok and drove. it suddenly did the same thing 2 more times before i was able to get home. the obd2 code was p2111, the drive by wire throttle bodies on these cars are faulty. seems to be a common problem. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 62107 miles. Ford Fusion 2010 problem was reported in CUMBERLAND, RI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Vehicle Speed Control Review #10468275

FORD FUSION 2010 car safety problem was reported on July 28, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . i had this issue when i first bought the car. driving on the hwy going 65 and all of a sudden the car lost acceleration and shook violently and stalled out. the wrench light came on and the vehicle went into stealth mode. this happen again on 07/16/2012, my daughter was driving the car. then it happen again on 07/28/2012. i took the car into the dealership and they did not get any of the codes, i guess because we turned the car off. at this point, i do not know what to do. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 67000 miles. Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in DURHAM, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10468282

FORD FUSION 2010 car safety problem was reported on July 05, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . had noticed several times that the vehicle hesitated to accelerate after pushing the gas. later that afternoon, while accelerating from a stoplight, the vehicle started shaking and lost all power. i was able to get the vehicle into a parking lot and turned it off. when i restarted, the engine seemed to run normally but still hesitated to go when the gas was pressed. i got the car to a dealership and they explained that the throttle body was bad - "a common thing on these cars". ford is refusing to cover the replacement under warranty, claiming that this is not part of the drive train - though admitting that the car will not function without the part. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 44000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in TULSA, OK. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10468282

FORD FUSION 2010 car safety problem was reported on July 05, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . had noticed several times that the vehicle hesitated to accelerate after pushing the gas. later that afternoon, while accelerating from a stoplight, the vehicle started shaking and lost all power. i was able to get the vehicle into a parking lot and turned it off. when i restarted, the engine seemed to run normally but still hesitated to go when the gas was pressed. i got the car to a dealership and they explained that the throttle body was bad - "a common thing on these cars". ford is refusing to cover the replacement under warranty, claiming that this is not part of the drive train - though admitting that the car will not function without the part. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 44000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in TULSA, OK. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10468282

FORD FUSION 2010 car safety problem was reported on July 05, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . had noticed several times that the vehicle hesitated to accelerate after pushing the gas. later that afternoon, while accelerating from a stoplight, the vehicle started shaking and lost all power. i was able to get the vehicle into a parking lot and turned it off. when i restarted, the engine seemed to run normally but still hesitated to go when the gas was pressed. i got the car to a dealership and they explained that the throttle body was bad - "a common thing on these cars". ford is refusing to cover the replacement under warranty, claiming that this is not part of the drive train - though admitting that the car will not function without the part. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 44000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in TULSA, OK. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Power Train Review #10468376

FORD FUSION 2010 car safety problem was reported on July 30, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . today my 2010 ford fusion lost acceleration on i35 surrounded by semi-trucks at 70mph. the wrench light came on and we could not get out of the way of the trucks behind us. fortunately the trucks were able to go around us and the traffic behind us was about a couple of miles away. we were in the middle of the three lane highway with my 18 month old son in the back seat, so i'm astonish that ford could build such a car and not acknowledge the safety issue. we were able to coast to so the shoulder and turn the car off. the car came back on with no issues indicated on the dash. we then started our way down i35 and the car lost acceleration again at 70mph. this time i was prepared and easily coasted onto the shoulder. the car was rough in idle, but when we turned it off and on again it was fine. i made the decision not to hit 70mph but to go only 60 until we got home. today we went to sea world and on the way home we almost became another statistic because of the ford company. i will go to the ford dealership where i bought the fusion from to see how they can help. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 51375 miles. Vehicle Identification Number (VIN):3FAHP0HG3AR. Ford Fusion 2010 problem was reported in AUSTIN, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train Review #10468385

FORD FUSION 2010 car safety problem was reported on July 29, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . throttle control is defective. i have read several complaints about the same issue. the throttle control goes bad and then the car will abruptly lose power and stop in traffic. we were lucky that we weren't on the interstate when this happened. in order to move you have to put the car in park and shut it off and turn it back on. i had to have mine replaced yesterday. the car is only two years old and only has 50,000 miles on it. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 50000 miles. Ford Fusion 2010 problem was reported in AUGUSTA, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10468385

FORD FUSION 2010 car safety problem was reported on July 29, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . throttle control is defective. i have read several complaints about the same issue. the throttle control goes bad and then the car will abruptly lose power and stop in traffic. we were lucky that we weren't on the interstate when this happened. in order to move you have to put the car in park and shut it off and turn it back on. i had to have mine replaced yesterday. the car is only two years old and only has 50,000 miles on it. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 50000 miles. Ford Fusion 2010 problem was reported in AUGUSTA, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10468445

FORD FUSION 2010 car safety problem was reported on July 27, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact tated that while driving approximately 40 mph, the vehicle suddenly stalled without warning. the vehicle was towed to the dealer for a diagnostic test. the technician stated that the throttle would have to be replaced. the vehicle was not repaired. the vin was not available. the approximate failure mileage was 42,000. .0 person(s) were injured. 0 person(s) died.Mileage was 42000 miles. Ford Fusion 2010 problem was reported in ANTELOPE, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10468791

FORD FUSION 2010 car safety problem was reported on July 30, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with ENGINE . was driving home from work and the wrench light came on and the motor cut off on me, i was lucky because i had just got off of the interstate , i managed to be able to pull on the shoulder of the road set there for a few minutes and started the car. it started and the light went off and was able to drive home. took vehicle to ford dealer and they checked and said they couldn't find any fault codes. they told me it was the throttle bottle and i had it replaced, haven't drove it yet to see if that took care of the problem. i got on the internet and found that other people were having the same problem. i think this is a safety problem and some on could get injured or worst. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 39790 miles. Vehicle Identification Number (VIN):3FAHPOJA4AR. Ford Fusion 2010 problem was reported in LURAY, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10468791

FORD FUSION 2010 car safety problem was reported on July 30, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . was driving home from work and the wrench light came on and the motor cut off on me, i was lucky because i had just got off of the interstate , i managed to be able to pull on the shoulder of the road set there for a few minutes and started the car. it started and the light went off and was able to drive home. took vehicle to ford dealer and they checked and said they couldn't find any fault codes. they told me it was the throttle bottle and i had it replaced, haven't drove it yet to see if that took care of the problem. i got on the internet and found that other people were having the same problem. i think this is a safety problem and some on could get injured or worst. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 39790 miles. Vehicle Identification Number (VIN):3FAHPOJA4AR. Ford Fusion 2010 problem was reported in LURAY, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train Review #10468847

FORD FUSION 2010 car safety problem was reported on Aug 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . car came to a chugging stop and a wrench symbol appeared on the console. after shutting off the car for a few minutes, the car started up and the symbol was gone. i am trying to get in touch with ford. i have found out on the net that this is a big problem with the ford fusion. this is a big safety issue because it has happened to hundreds of fusion owners. i have 20 pages of testimonials about this problem. i think it is time for a recall of this problem! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 50000 miles. Ford Fusion 2010 problem was reported in EMBDEN, ME. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10468979

FORD FUSION 2010 car safety problem was reported on July 25, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . driving on florida turnpike, just got on highway and at high speed the check engine light came on, diagnosed as code p2111, throttle stuck open by dtc reader. immediately lost power and about grinded to a halt, had to pull off road and limp to next exit. vehicle stuck in idle until restarted and had no further problems for a few miles but keeps coming up. cannot drive car on highway for fear of another dangerous failure. ford says throttle body is bad, no warrantied after 36,000 miles. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Ford Fusion 2010 problem was reported in CUTLER BAY, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10468979

FORD FUSION 2010 car safety problem was reported on July 25, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . driving on florida turnpike, just got on highway and at high speed the check engine light came on, diagnosed as code p2111, throttle stuck open by dtc reader. immediately lost power and about grinded to a halt, had to pull off road and limp to next exit. vehicle stuck in idle until restarted and had no further problems for a few miles but keeps coming up. cannot drive car on highway for fear of another dangerous failure. ford says throttle body is bad, no warrantied after 36,000 miles. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Ford Fusion 2010 problem was reported in CUTLER BAY, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Air Bags

Ford Fusion 2010 Air Bags Review #10469065

FORD FUSION 2010 car safety problem was reported on July 25, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with AIR BAGS . tl* the contact owns a 2010 ford fusion. the contact stated that the vehicle was rear ended by another vehicle traveling 50 mph while the contact was sitting idle. the driver and passenger side air bags deployed. the lid to the passenger side air bag compartment exploded and bore a hole the size of a fist through the front windshield. the driver and passenger sustained neck, back, chest and rib injuries from the impact. the contact was concerned with the manner in which the air bags deployed. the vehicle was destroyed. the current and failure mileage was 30,000. .Vehicle was involved in a crash. 2 person(s) were injured. 0 person(s) died.Mileage was 30000 miles. Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in AUSTIN, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10469106

FORD FUSION 2010 car safety problem was reported on Aug 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . was driving at low speed (approx 20 mph) and car jerked violently and wrench light came on. rpms were then stuck ~1000 and car would not accelerate when gas pedal was depressed. coasted to a stop, shifted to park, and turned off the car. tried to re-start the car immediately and it would not turn over. after the car sat for approx 5 min, started fine and drove fine. dealership could not find problem. also experience a strong jerking motion regularly when first start car (it is cold) when shifting from park into drive/reverse). and have occasionally experienced an engine revving at higher speeds (40 mph). *tr.0 person(s) were injured. 0 person(s) died.Mileage was 46000 miles. Ford Fusion 2010 problem was reported in WATERFORD, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10469183

FORD FUSION 2010 car safety problem was reported on Aug 04, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . driving on highway the accelerator stopped working. pulled the car off the road avoiding accident. turned car off. turned car back on working normally. 1 mile later same problem occurred. this happened 12 times in 12 mile stretch. throttle body is bad. this is common problem and needs to be recalled. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 54000 miles. Ford Fusion 2010 problem was reported in SOUTH POINT, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10469183

FORD FUSION 2010 car safety problem was reported on Aug 04, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . driving on highway the accelerator stopped working. pulled the car off the road avoiding accident. turned car off. turned car back on working normally. 1 mile later same problem occurred. this happened 12 times in 12 mile stretch. throttle body is bad. this is common problem and needs to be recalled. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 54000 miles. Ford Fusion 2010 problem was reported in SOUTH POINT, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10469183

FORD FUSION 2010 car safety problem was reported on Aug 04, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . driving on highway the accelerator stopped working. pulled the car off the road avoiding accident. turned car off. turned car back on working normally. 1 mile later same problem occurred. this happened 12 times in 12 mile stretch. throttle body is bad. this is common problem and needs to be recalled. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 54000 miles. Ford Fusion 2010 problem was reported in SOUTH POINT, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10469186

FORD FUSION 2010 car safety problem was reported on Aug 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . i stopped the car to close the gas fill lid, engine running, went to get back in and all doors were locked, they locked themselves. it was over 90 degrees out, lucky i had my cell phone to call my wife to bring her keys so i could get back in. if my grandkids had been the car, it could have been a scary problem. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 19945 miles. Vehicle Identification Number (VIN):3FAHP0HG5AR. Ford Fusion 2010 problem was reported in LAPORTE, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Latches/locks/linkages

Ford Fusion 2010 Latches/locks/linkages Review #10469186

FORD FUSION 2010 car safety problem was reported on Aug 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with LATCHES/LOCKS/LINKAGES . i stopped the car to close the gas fill lid, engine running, went to get back in and all doors were locked, they locked themselves. it was over 90 degrees out, lucky i had my cell phone to call my wife to bring her keys so i could get back in. if my grandkids had been the car, it could have been a scary problem. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 19945 miles. Vehicle Identification Number (VIN):3FAHP0HG5AR. Ford Fusion 2010 problem was reported in LAPORTE, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10469195

FORD FUSION 2010 car safety problem was reported on Aug 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . first incident happened in may 26 2012- was exiting freeway, let off gas and car went into "limp mode" pulled car over and turned off and restarted 5 min later second inc. may 26 2012 - same as above. third inc. aug 3 2012 - sitting at a stop light, when light turned green hit the gas then it switches to "limp mode" idle, we coasted through the light to park on side of road. it started back up fine a few minutes later. fourth inc. aug 3 2012 - driving down freeway at 65mph when let off the gas car switched to "limp mode" again. had to turn car off then turn back on. few minutes later it happened again and turned car off and on again, would not go out of "limp mode" and had to drive home in idle on side of freeway. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 36877 miles. Vehicle Identification Number (VIN):3FAHP0JG9AR. Ford Fusion 2010 problem was reported in ANTIOCH, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10469282

FORD FUSION 2010 car safety problem was reported on July 26, 2011.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . tl* the contact owns a 2010 ford fusion. the contact stated that the vehicle stalled several times without warning while driving at various speeds. the wrench warning light illuminated after the failure occurred. the vehicle was taken to the dealer and a diagnostic was performed but the technicians were unable to generate a failure code. the vehicle was not repaired. the manufacturer was not made aware of the failure. the failure mileage was 18,000 and the current mileage 21,000. .0 person(s) were injured. 0 person(s) died.Mileage was 18000 miles. Vehicle Identification Number (VIN):3FAHP0JG3AR. Ford Fusion 2010 problem was reported in KINGSTON, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10469345

FORD FUSION 2010 car safety problem was reported on Aug 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . transmission slips 4cylinder 6 speed automatic. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 29400 miles. Vehicle Identification Number (VIN):3FAHP0JA5AR. Ford Fusion 2010 problem was reported in TEWKSBURY, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Service Brakes

Ford Fusion 2010 Service Brakes Review #10469355

FORD FUSION 2010 car safety problem was reported on Aug 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES . pushing hard on the brake pedal causes it to go below the gas pedal letting my foot push both the gas and brake pedals at the same time. *tr .0 person(s) were injured. 0 person(s) died.Mileage was 7700 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in FALCON HEIGHTS, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 1 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10469600

FORD FUSION 2010 car safety problem was reported on Aug 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . moving along at 40mph when car suddenly jerks and loses power. orange wrench light comes on but my car stalled out in traffic. turned key off and back on-car started and light was off. a minute down the road and car did same thing again. this continues to happen 5 days later. very dangerous because car loses throttle power completely. i do not dare go down interstate with this problem. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 90000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in MOUNT JULIET, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10469600

FORD FUSION 2010 car safety problem was reported on Aug 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . moving along at 40mph when car suddenly jerks and loses power. orange wrench light comes on but my car stalled out in traffic. turned key off and back on-car started and light was off. a minute down the road and car did same thing again. this continues to happen 5 days later. very dangerous because car loses throttle power completely. i do not dare go down interstate with this problem. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 90000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in MOUNT JULIET, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10469933

FORD FUSION 2010 car safety problem was reported on July 26, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. while driving approximately 40 mph the vehicle stalled without warning. the vehicle began to shake when the contact attempted to start the vehicle. the contact was able to restart the vehicle. the failure recurred four different times. the vehicle was taken to the dealer for diagnostic testing. the technician stated that the throttle body would have to be replaced. the vehicle was not repaired. the approximate failure mileage was 54,000. updated 10/10/12 *cn.0 person(s) were injured. 0 person(s) died.Mileage was 54000 miles. Vehicle Identification Number (VIN):3FAHP0HA9AR. Ford Fusion 2010 problem was reported in FLORENCE, AL. Vehicle was purchased on Apr 01, 2012. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph. DEALER'S NAME: LONG-LEWIS FORD . DEALER'S TELEPHONE NUMBER: 256-386-7801 . DEALER'S CITY: MUSCLE SHOALS . DEALER'S STATE CODE: AL. DEALER'S ZIPCODE: 35661 .

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10469933

FORD FUSION 2010 car safety problem was reported on July 26, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with ENGINE AND ENGINE COOLING . tl* the contact owns a 2010 ford fusion. while driving approximately 40 mph the vehicle stalled without warning. the vehicle began to shake when the contact attempted to start the vehicle. the contact was able to restart the vehicle. the failure recurred four different times. the vehicle was taken to the dealer for diagnostic testing. the technician stated that the throttle body would have to be replaced. the vehicle was not repaired. the approximate failure mileage was 54,000. updated 10/10/12 *cn.0 person(s) were injured. 0 person(s) died.Mileage was 54000 miles. Vehicle Identification Number (VIN):3FAHP0HA9AR. Ford Fusion 2010 problem was reported in FLORENCE, AL. Vehicle was purchased on Apr 01, 2012. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph. DEALER'S NAME: LONG-LEWIS FORD . DEALER'S TELEPHONE NUMBER: 256-386-7801 . DEALER'S CITY: MUSCLE SHOALS . DEALER'S STATE CODE: AL. DEALER'S ZIPCODE: 35661 .

Ford Fusion 2010 Engine Review #10470091

FORD FUSION 2010 car safety problem was reported on Aug 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . i was driving my wife and newborn child home from the hospital when my car lost all acceleration. it was an unsafe situation and i responded by pulling my vehicle into the breakdown lane. i shut off the engine and started the vehicle and continued to drive. the vehicle lost acceleration 2 more times on my way home. the wrench icon came on when the incidents occurred. i believe it is the throttle body. this is a major safety issue ford must address. there is no indication that the vehicle is about to lose all acceleration. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 56002 miles. Ford Fusion 2010 problem was reported in REHOBOTH, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10470091

FORD FUSION 2010 car safety problem was reported on Aug 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . i was driving my wife and newborn child home from the hospital when my car lost all acceleration. it was an unsafe situation and i responded by pulling my vehicle into the breakdown lane. i shut off the engine and started the vehicle and continued to drive. the vehicle lost acceleration 2 more times on my way home. the wrench icon came on when the incidents occurred. i believe it is the throttle body. this is a major safety issue ford must address. there is no indication that the vehicle is about to lose all acceleration. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 56002 miles. Ford Fusion 2010 problem was reported in REHOBOTH, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Electronic Stability Control

Ford Fusion 2010 Electronic Stability Control Review #10470091

FORD FUSION 2010 car safety problem was reported on Aug 03, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRONIC STABILITY CONTROL . i was driving my wife and newborn child home from the hospital when my car lost all acceleration. it was an unsafe situation and i responded by pulling my vehicle into the breakdown lane. i shut off the engine and started the vehicle and continued to drive. the vehicle lost acceleration 2 more times on my way home. the wrench icon came on when the incidents occurred. i believe it is the throttle body. this is a major safety issue ford must address. there is no indication that the vehicle is about to lose all acceleration. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 56002 miles. Ford Fusion 2010 problem was reported in REHOBOTH, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10470276

FORD FUSION 2010 car safety problem was reported on Aug 10, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . was driving down the highway at 60-65 mph when suddenly car jerked and lost all acceleration power. the rpms were stuck (not going up or down) and car began to slow down. the wrench light came on. i had to pull to the side of the highway to avoid getting hit. tried putting the car in park and back into drive, but it started shaking, so had to turn off the car, let it sit for a few minutes and re-start the car. it drove normally after re-start, however this was the second occurrence in one week and am now scared to drive it long distances or on the highway. ford needs to fix this issue before someone gets hurt! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 45500 miles. Ford Fusion 2010 problem was reported in WATERFORD, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10470276

FORD FUSION 2010 car safety problem was reported on Aug 10, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . was driving down the highway at 60-65 mph when suddenly car jerked and lost all acceleration power. the rpms were stuck (not going up or down) and car began to slow down. the wrench light came on. i had to pull to the side of the highway to avoid getting hit. tried putting the car in park and back into drive, but it started shaking, so had to turn off the car, let it sit for a few minutes and re-start the car. it drove normally after re-start, however this was the second occurrence in one week and am now scared to drive it long distances or on the highway. ford needs to fix this issue before someone gets hurt! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 45500 miles. Ford Fusion 2010 problem was reported in WATERFORD, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Latches/locks/linkages

Ford Fusion 2010 Latches/locks/linkages Review #10470338

FORD FUSION 2010 car safety problem was reported on Aug 12, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with LATCHES/LOCKS/LINKAGES . tl* the contact owns a 2010 ford fusion. the contact stated she was unable to unlock the drivers door the with the automatic lock. the drivers side door could only be opened by using the outside door handle. the vehicle was not taken to the dealer for diagnostic testing.. the manufacturer was not made aware of the failure. the vehicle was not repaired. the failure and current mileage was 72,781. .0 person(s) were injured. 0 person(s) died.Mileage was 72781 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in ARBERNE, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10470394

FORD FUSION 2010 car safety problem was reported on Aug 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact stated that while driving approximately 65 mph the vehicle failed to accelerate. the contact stopped on the shoulder of the road and shut the engine off. after restarting the vehicle the wrench warning light illuminated. the vehicle was taken to the dealer who diagnosed that the throttle body needed to be replaced. the vehicle was repaired. the approximate failure mileage was 62,628..0 person(s) were injured. 0 person(s) died.Mileage was 62628 miles. Vehicle Identification Number (VIN):3FAHP0HA1AR. Ford Fusion 2010 problem was reported in KNOXVILLE, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10470444

FORD FUSION 2010 car safety problem was reported on Aug 11, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . driving down the road at 45mph and the car starts vibrating. all of a sudden i lose acceleration while my foot is still on the gas. luckily i was able to pull over before the car lost momentum and stalled out. the wrench light was on. had no warning at all. i shut the car off, waited about 2-3 minutes and tried to start it again. it turned over but after it struggled to. the wrench light then went off. this has happened four more times! each with no warning! i have looked on a number of sited that have the same complaint about this. there are hundreds of near crash cases and all with no warning. i love how this website says "your complaint information will be entered into nhtsa-odi's vehicle owner's complaint database and used with other complaints to determine if a safety-related defect trend exists" after numerous complaints and an obvious faulty part you still haven't seen a trend? are you kidding me?! today i just missed getting into an accident as the car decided to lose acceleration again as i was pulling out to make a turn across 4 lanes. the lanes were clear to go but oncoming traffic was coming. i was lucky that the person saw my flashers and had the room to move over and get out of the way. apparently ford wants a lawsuit on their hands because as soon as someone gets into an accident(if they have not already) you better bet they'll go after ford. especially since it is apparent that ford has been made aware of this problem and still will not take responsibility for the fact something is wrong. you better believe that if i get hit because there product was not recalled because of a faulty part i'll be front and center with my lawyer and a news crew. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 57000 miles. Vehicle Identification Number (VIN):3FAHP0HG1AR. Ford Fusion 2010 problem was reported in GLENDALE, AZ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10470444

FORD FUSION 2010 car safety problem was reported on Aug 11, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . driving down the road at 45mph and the car starts vibrating. all of a sudden i lose acceleration while my foot is still on the gas. luckily i was able to pull over before the car lost momentum and stalled out. the wrench light was on. had no warning at all. i shut the car off, waited about 2-3 minutes and tried to start it again. it turned over but after it struggled to. the wrench light then went off. this has happened four more times! each with no warning! i have looked on a number of sited that have the same complaint about this. there are hundreds of near crash cases and all with no warning. i love how this website says "your complaint information will be entered into nhtsa-odi's vehicle owner's complaint database and used with other complaints to determine if a safety-related defect trend exists" after numerous complaints and an obvious faulty part you still haven't seen a trend? are you kidding me?! today i just missed getting into an accident as the car decided to lose acceleration again as i was pulling out to make a turn across 4 lanes. the lanes were clear to go but oncoming traffic was coming. i was lucky that the person saw my flashers and had the room to move over and get out of the way. apparently ford wants a lawsuit on their hands because as soon as someone gets into an accident(if they have not already) you better bet they'll go after ford. especially since it is apparent that ford has been made aware of this problem and still will not take responsibility for the fact something is wrong. you better believe that if i get hit because there product was not recalled because of a faulty part i'll be front and center with my lawyer and a news crew. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 57000 miles. Vehicle Identification Number (VIN):3FAHP0HG1AR. Ford Fusion 2010 problem was reported in GLENDALE, AZ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10470444

FORD FUSION 2010 car safety problem was reported on Aug 11, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . driving down the road at 45mph and the car starts vibrating. all of a sudden i lose acceleration while my foot is still on the gas. luckily i was able to pull over before the car lost momentum and stalled out. the wrench light was on. had no warning at all. i shut the car off, waited about 2-3 minutes and tried to start it again. it turned over but after it struggled to. the wrench light then went off. this has happened four more times! each with no warning! i have looked on a number of sited that have the same complaint about this. there are hundreds of near crash cases and all with no warning. i love how this website says "your complaint information will be entered into nhtsa-odi's vehicle owner's complaint database and used with other complaints to determine if a safety-related defect trend exists" after numerous complaints and an obvious faulty part you still haven't seen a trend? are you kidding me?! today i just missed getting into an accident as the car decided to lose acceleration again as i was pulling out to make a turn across 4 lanes. the lanes were clear to go but oncoming traffic was coming. i was lucky that the person saw my flashers and had the room to move over and get out of the way. apparently ford wants a lawsuit on their hands because as soon as someone gets into an accident(if they have not already) you better bet they'll go after ford. especially since it is apparent that ford has been made aware of this problem and still will not take responsibility for the fact something is wrong. you better believe that if i get hit because there product was not recalled because of a faulty part i'll be front and center with my lawyer and a news crew. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 57000 miles. Vehicle Identification Number (VIN):3FAHP0HG1AR. Ford Fusion 2010 problem was reported in GLENDALE, AZ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train Review #10470500

FORD FUSION 2010 car safety problem was reported on Aug 13, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . this morning i'm in my 2010 ford fusion traveling about 50 mph and all of a sudden i start to slow down and i lose ability to accelerate. the wrench indicator on the dash is lit which indicates throttle/transmission failure. i roll into a parking lot and shut the car. turn it back on after a minute and it runs fine. later in the day on my way home from work the same thing happens. this seems to be a very common problem and ford needs to do something. i'm reading this is not covered under warranty. that's doesn't seem very fair since its clear this is something that's happening to lots of owners. it can't be a coincidence and it must be something defective in the build. they can word it however they want but something that causes you to lose "power" i would think is part of the powertrain warranty. do the right thing ford.. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 30200 miles. Ford Fusion 2010 problem was reported in AMITYVILLE, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Power Train Review #10470518

FORD FUSION 2010 car safety problem was reported on Aug 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . my cars transmission shut off, a wrench light came on and i couldn't accelerate. car started shaking violently. had to restart it to drive again. car does it at random. its my only car and its my life line with out it i cant get to work. *tr.Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Mileage was 53000 miles. Vehicle Identification Number (VIN):3FAHP0HA2AR. Ford Fusion 2010 problem was reported in LAKE WORTH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10470518

FORD FUSION 2010 car safety problem was reported on Aug 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . my cars transmission shut off, a wrench light came on and i couldn't accelerate. car started shaking violently. had to restart it to drive again. car does it at random. its my only car and its my life line with out it i cant get to work. *tr.Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Mileage was 53000 miles. Vehicle Identification Number (VIN):3FAHP0HA2AR. Ford Fusion 2010 problem was reported in LAKE WORTH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10470654

FORD FUSION 2010 car safety problem was reported on Aug 13, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . 2010 ford fusion has pinhole in evaporator core/valve. the cheapest estimate is over $900.00 and this car is 3 yrs old with 65,000 miles. *tr .0 person(s) were injured. 0 person(s) died.Mileage was 65500 miles. Vehicle Identification Number (VIN):3FAHP0HA9AR. Ford Fusion 2010 problem was reported in LEXINGTON, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10470807

FORD FUSION 2010 car safety problem was reported on Aug 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact stated that while driving 65 mph and attempting to accelerate, the vehicle failed to respond. the vehicle began to loose power and shook abnormally. the wrench warning light was also illuminated. the contact was able to stop, turn off and restart the vehicle. the failure was corrected momentarily however, recurred shortly after. the vehicle was taken to a local mechanic who inspected the vehicle and determined that failure was caused by a defective throttle body. the vehicle was repaired by replacing the throttle body. the manufacturer was not made aware of the failure. the vin was unavailable. the current and failure mileage was 75,000. .0 person(s) were injured. 0 person(s) died.Mileage was 75000 miles. Ford Fusion 2010 problem was reported in FORT WAYNE, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10470839

FORD FUSION 2010 car safety problem was reported on Apr 17, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . while driving engine cut out causing the car to stall in traffic. i brought the car to the ford dealership and it was diagnosed as a faulty fuel injector #2. same issue happened approximately 5000 miles later then again 10000 miles later. each time the vehicle was brought to a ford dealership. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 36100 miles. Vehicle Identification Number (VIN):3FAHP0JA3AR. Ford Fusion 2010 problem was reported in TOCCOA, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Engine Review #10471252

FORD FUSION 2010 car safety problem was reported on July 01, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . tl* the contact owns a 2010 ford fusion. the contact stated that while driving 30 mph, the vehicle stalled without warning. the contact was able to restart the vehicle. the failure recurred frequently. the vehicle was not taken to the dealer for inspection or repairs. the manufacturer was not made aware of the failure. the current mileage was 59,000. the failure mileage was 55,000. .0 person(s) were injured. 0 person(s) died.Mileage was 55000 miles. Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in LAPEER, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10471367

FORD FUSION 2010 car safety problem was reported on July 15, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . returning to tn from vacation in fl on 7/15/12. traveling before birmingham, al - heard a loud boom sound (like a tire blow out), then heard a roar. as we signaled to move from the fast lane to the emergency lane - flames were over the back window of the car. by the time that we reached the emergency lane, the entire car was engulfed in flames both inside and outside. the car was entirely engulfed in flames within 10 to 20 seconds. i had purchased the car from moss motor company in south pittsburgh, tn on 6/4/12. the car had issues within two weeks that required the car to be towed back to the dealer for powertrain issue. dealer did not share the ticket with me on repairs that were completed two weeks before the car exploded. but they kept the car for over one week to fix the issue that caused it to stop pulling while driving. this was the first long trip that i had taken in the car. my two passengers experienced mild burns but we lost all personal items in the car due to the speed that the car burned. alabama highway patrol worked the explosion and fire department had to work the fire. state farm assured me that they would investigate the cause of the fire but has just informed me that they did not do a thorough investigation. i have witness names and contact information as well as photographs that they took as the car burned if needed. *tr.Vehicle was on fire. 2 person(s) were injured. 0 person(s) died.Mileage was 19800 miles. Vehicle Identification Number (VIN):JN1AZ34D04M. Ford Fusion 2010 problem was reported in JASPER, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10471367

FORD FUSION 2010 car safety problem was reported on July 15, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . returning to tn from vacation in fl on 7/15/12. traveling before birmingham, al - heard a loud boom sound (like a tire blow out), then heard a roar. as we signaled to move from the fast lane to the emergency lane - flames were over the back window of the car. by the time that we reached the emergency lane, the entire car was engulfed in flames both inside and outside. the car was entirely engulfed in flames within 10 to 20 seconds. i had purchased the car from moss motor company in south pittsburgh, tn on 6/4/12. the car had issues within two weeks that required the car to be towed back to the dealer for powertrain issue. dealer did not share the ticket with me on repairs that were completed two weeks before the car exploded. but they kept the car for over one week to fix the issue that caused it to stop pulling while driving. this was the first long trip that i had taken in the car. my two passengers experienced mild burns but we lost all personal items in the car due to the speed that the car burned. alabama highway patrol worked the explosion and fire department had to work the fire. state farm assured me that they would investigate the cause of the fire but has just informed me that they did not do a thorough investigation. i have witness names and contact information as well as photographs that they took as the car burned if needed. *tr.Vehicle was on fire. 2 person(s) were injured. 0 person(s) died.Mileage was 19800 miles. Vehicle Identification Number (VIN):JN1AZ34D04M. Ford Fusion 2010 problem was reported in JASPER, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Power Train Review #10471544

FORD FUSION 2010 car safety problem was reported on Aug 18, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . tl* the contact owns a 2010 ford fusion. the contact stated that while driving 75 mph, the vehicle lost power and became inoperable. the failure recurred frequently. the vehicle was taken to the dealer where the contact was awaiting diagnosis of the failure. the manufacturer was notified of the failure who advised the contact to file a safety complaint and offered no further assistance. the vin was not available. the failure and current mileage was 52,000. .0 person(s) were injured. 0 person(s) died.Mileage was 52000 miles. Ford Fusion 2010 problem was reported in SANTA CLARITA, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 75 mph.

Ford Fusion 2010 Power Train Review #10471600

FORD FUSION 2010 car safety problem was reported on Aug 17, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . leaving from work on friday afternoon, my 2010 ford fusion lost power as i pull out of the parking lot, it slowed down and i lose ability to accelerate. the wrench indicator on the dash is lit which indicates throttle/transmission failure. the engine was vibrating bad and the engine would not rev up. i roll into a parking lot and shut the engine off. i restarted the engine after a minute and it ran fine. this happens two more times in 30 minutes on my way to the dealer. they knew exactly what the problem was they said it is a very common problem with this car. i was luckily to not get rear ended the 3 times in 30 minutes it lost power. the dealer says it is not covered under warranty. that's stupid that ford would not cover the cost to fix their mechanical defects, this is a design defect as there are many complaints filed for this defect. this should be part of the powertrain warranty. looks like no 2013 f-150 is in my future plans since i was going the buy one. do the right thing ford. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 38500 miles. Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in ROSHARON, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 5 mph.

Ford Fusion 2010 Engine And Engine Cooling

Ford Fusion 2010 Engine And Engine Cooling Review #10471633

FORD FUSION 2010 car safety problem was reported on Aug 19, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . on 8/19/12, we were traveling on i-96 in the left lane at 70 mph when the car suddenly lost power and i could barely drive to the right shoulder. the motor sputtered and seemingly try to die. the wrench light came on. i turned off the motor, called for help, when help arrived, the technician asked me to start the car. it started. my wife and i were able to get home. on 8/20/12, i took it to a ford dealer to get the matter checked as well as get an oil change. the dealer "scoped" the computer and could find nothing wrong. this evening, 8/20/12, i was driving at 35 miles an hour when there was a lurch and i lost power. i could not accelerate so i turned off the ignition, waited a few seconds, and turned on the motor. i was able to drive home. i've checked a website that indicates there have been quite a few other problems along the same lines as i experienced. i will take the car back to the dealer for a check again but based upon what i read about other complaints, i doubt if the dealer will figure out the issue. this is a very dangerous situation particularly while driving on a freeway at 70 mph and losing total power. had we not been driving on a sunday when traffic was relatively light, we would undoubtedly have been in a serious accident. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 48365 miles. Vehicle Identification Number (VIN):3FAHPOJG3AR. Ford Fusion 2010 problem was reported in PLYMOUTH, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10471633

FORD FUSION 2010 car safety problem was reported on Aug 19, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with FUEL/PROPULSION SYSTEM . on 8/19/12, we were traveling on i-96 in the left lane at 70 mph when the car suddenly lost power and i could barely drive to the right shoulder. the motor sputtered and seemingly try to die. the wrench light came on. i turned off the motor, called for help, when help arrived, the technician asked me to start the car. it started. my wife and i were able to get home. on 8/20/12, i took it to a ford dealer to get the matter checked as well as get an oil change. the dealer "scoped" the computer and could find nothing wrong. this evening, 8/20/12, i was driving at 35 miles an hour when there was a lurch and i lost power. i could not accelerate so i turned off the ignition, waited a few seconds, and turned on the motor. i was able to drive home. i've checked a website that indicates there have been quite a few other problems along the same lines as i experienced. i will take the car back to the dealer for a check again but based upon what i read about other complaints, i doubt if the dealer will figure out the issue. this is a very dangerous situation particularly while driving on a freeway at 70 mph and losing total power. had we not been driving on a sunday when traffic was relatively light, we would undoubtedly have been in a serious accident. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 48365 miles. Vehicle Identification Number (VIN):3FAHPOJG3AR. Ford Fusion 2010 problem was reported in PLYMOUTH, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10471700

FORD FUSION 2010 car safety problem was reported on May 01, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . tl* the contact owns a 2010 ford fusion. the contact stated that he purchased the vehicle because one of the benefits stated in the owner's manual was that the vehicle could be towed with four wheels touching the pavement. the contact stated that the vehicle was towed and as a result, destroyed the transmission. the vehicle was taken to the dealer where the transmission was repaired. the manufacturer was notified but offered no assistance. the failure mileage was 36,000 and the current mileage was 40,000. updated 09/26/12*lj the cosumer stated ford offered to pay 1/3 the reppairs along with the dealer and thee owner. the consumer traded to the vehicle in since the vehicle was not 4 wheel towable. updated 09/27/2012 *js.0 person(s) were injured. 0 person(s) died.Mileage was 36000 miles. Vehicle Identification Number (VIN):3FAHP0HA6AR. Ford Fusion 2010 problem was reported in HIGH SPRINGS, FL. Original Owner. Vehicle was purchased on Feb 19, 2010. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 55 mph. DEALER'S NAME: SANTA FE FORD . DEALER'S TELEPHONE NUMBER: 386-462-2802 . DEALER'S CITY: ALACHUA . DEALER'S STATE CODE: FL. DEALER'S ZIPCODE: 32615 .

Ford Fusion 2010 Wheels

Ford Fusion 2010 Wheels Review #10471846

FORD FUSION 2010 car safety problem was reported on Aug 15, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with WHEELS . lug nut recall is not an effective solution. this car had a lug shear in 2011. i had meridian ford perform the recall service jan. 26th of 2012. mid aug of 2012 i noticed another lug had sheared. no one has touched/tightened the lug nuts. the process of simply replacing lug nuts and the already sheared lugs is not effective. it is just a matter of time until all of those lugs are stressed to the point of shearing. i can not get the ford dealer to do anything other than replace the sheared lug. i am afraid to drive this car as it is not safe and the wheels may separate at any time. i'd like to know what course of action to take next? *tr.0 person(s) were injured. 0 person(s) died.Mileage was 32000 miles. Vehicle Identification Number (VIN):3FAHP0HA9AR. Ford Fusion 2010 problem was reported in MIDDLETON, ID. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10472830

FORD FUSION 2010 car safety problem was reported on Aug 14, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . i was driving down the highway when i noticed that i could no longer accelerate. i coasted to a stop, the car shaking as it came to a stop. i placed the car in park, turned the car off, and restarted. it started up fine, and then it happened again about 10 minutes later. after a mechanic was unable to duplicate the problem, i thought it was perhaps "bad gas" and moved on. two weeks later, it happened twice, once stopping me in the middle of a busy intersection (because this time i wasn't going 60mph this time). the diagnosis from ford: a faulty throttle body sensor. the car is barely three years old, it has a significant defect (not caused by wear-and-tear or user-error), but it is not covered under their warranty. the mechanic at ford says that they see a lot of these situations. they are grossly negligent in not warning families and offering to fix their mistakes by replacing the bad throttle body components. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 43000 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in LAND O LAKES, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10472830

FORD FUSION 2010 car safety problem was reported on Aug 14, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ENGINE . i was driving down the highway when i noticed that i could no longer accelerate. i coasted to a stop, the car shaking as it came to a stop. i placed the car in park, turned the car off, and restarted. it started up fine, and then it happened again about 10 minutes later. after a mechanic was unable to duplicate the problem, i thought it was perhaps "bad gas" and moved on. two weeks later, it happened twice, once stopping me in the middle of a busy intersection (because this time i wasn't going 60mph this time). the diagnosis from ford: a faulty throttle body sensor. the car is barely three years old, it has a significant defect (not caused by wear-and-tear or user-error), but it is not covered under their warranty. the mechanic at ford says that they see a lot of these situations. they are grossly negligent in not warning families and offering to fix their mistakes by replacing the bad throttle body components. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 43000 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in LAND O LAKES, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10472830

FORD FUSION 2010 car safety problem was reported on Aug 14, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . i was driving down the highway when i noticed that i could no longer accelerate. i coasted to a stop, the car shaking as it came to a stop. i placed the car in park, turned the car off, and restarted. it started up fine, and then it happened again about 10 minutes later. after a mechanic was unable to duplicate the problem, i thought it was perhaps "bad gas" and moved on. two weeks later, it happened twice, once stopping me in the middle of a busy intersection (because this time i wasn't going 60mph this time). the diagnosis from ford: a faulty throttle body sensor. the car is barely three years old, it has a significant defect (not caused by wear-and-tear or user-error), but it is not covered under their warranty. the mechanic at ford says that they see a lot of these situations. they are grossly negligent in not warning families and offering to fix their mistakes by replacing the bad throttle body components. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 43000 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in LAND O LAKES, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10472834

FORD FUSION 2010 car safety problem was reported on Aug 27, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . i was pulling my 2010 ford fusion hybrid into a parking space at about 3 mph and the car suddenly surged forward. to avoid impact into the car in front of me, i turned the car into a parking block next to my parking space. as i did this, i jammed on the brake, put it in park and turned it off. damage to front bumper and casing in front of tire from hitting the parking block. drove to dealership with no problems. diagnostics revealed nothing. contacted ford corp. about the incident and will await to see if they will cover damages to my vehicle. *tr.Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Mileage was 24890 miles. Ford Fusion 2010 problem was reported in HADDONFIELD, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 3 mph.

Ford Fusion 2010 Service Brakes, Hydraulic

Ford Fusion 2010 Service Brakes, Hydraulic Review #10473484

FORD FUSION 2010 car safety problem was reported on Oct 01, 2011.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with SERVICE BRAKES, HYDRAULIC . 2010 ford fusion hybrid. consumer writes in regards to vehicle brake system *tgw the consumer stated in feb 2010, ford issued a customer satisfaction program recall to reprogram the brake system. unfortunately, the general recall did not correct the malfunction with his particular vehicle. since that time, he has continued to experience the problem that prompted the recall. the malfunction occurred randomly and with no warning. there were times, where the vehicle had been driven for months, with no problem. but, then without warning, the malfunction would occur again. according to ford, the brake system software may unnecessarily cause the regenerative brake system to transition to conventional brakes, if that occurs the red brake warning lamp will illuminate, the message check brake system will appear and a warning chime will sound. the consumer stated when the issue did occur, at times he was able to stop the vehicle, turn it off and re-start it; other times he would have to let the vehicle sit for an hour or more. .Vehicle Identification Number (VIN):3FADP0L35AR. Ford Fusion 2010 problem was reported in IRVINE, CA. Original Owner. Vehicle was purchased on Aug 16, 2009. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: HYBRID ELECTRIC. DEALER'S NAME: POWER FORD . DEALER'S CITY: TUSTIN . DEALER'S STATE CODE: CA.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10473072

FORD FUSION 2010 car safety problem was reported on Aug 28, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . i had been driving on a surface street for about 1 mile after coming off a highway. the car had come to a stop at least twice at traffic lights. i was coasting (foot not on brake or accelerator) when the car accelerated on its own from ~30 mph as if the cruise control (cc) had been activated. i touched the brake as quickly as possible (probably < 1sec of acceleration) and conditions returned to normal. looking at the dash, i noted that the cc master switch was on, but cc was not active before acceleration event or after braking. state during acceleration is unknown. my fingers were nowhere near the cc buttons (or any other steering wheel buttons) when the event occured. prior to the event: i was on a highway traveling about 60-65 mph with cc on and active. when cc is active, i always keep a thumb on the cancel/resume button. traffic slowed and i braked, then hit c/r (turning cc back to active -- my error). i immediately noticed the error and set the cc back to inactive (either by brake or cancel, i can't recall). cc was left in its master-on/inactive state when i came off the highway with active velocity set somewhere in the 60-65 mph range. this was the state of the cc system when the above described event occured. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 40100 miles. Vehicle Identification Number (VIN):3FAHP0GA8AR. Ford Fusion 2010 problem was reported in SANTA MONICA, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10473092

FORD FUSION 2010 car safety problem was reported on Aug 29, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with ENGINE . tl* the contact owns a 2010 ford fusion hybrid. the contact stated while driving 20 mph the vehicle stalled. the contact was able to maneuver to the shoulder in order to restart the vehicle. the dealer was contacted who advised the contact to bring the vehicle in to run a diagnostic test. the vehicle was not taken to the dealer. in addition, the contact stated that vehicle would not move when it was shifted in drive or reverse. the failure mileage was 46,000. .0 person(s) were injured. 0 person(s) died.Mileage was 46000 miles. Vehicle Identification Number (VIN):3FADP0L32AR. Ford Fusion 2010 problem was reported in SPANAWAY, WA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10473113

FORD FUSION 2010 car safety problem was reported on Aug 30, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . on a routine drive home from work, i exited the highway and noticed my rpms falling faster than what i was controlling with the brake. car was losing speed quickly with no rpms to accelerate it forward to a safe stopping point. was able to pull into a gas station right off highway, but barely as car was apparently entering limited power mode (determined via owners manual). upon placing car into car, dashboard wrench light illuminated. i then turned the car off, sat a minute, restarted car and everything was fine. within the course of the next 10 minutes, the same thing occurred 3 more times and check engine light illuminated. since the first time, this has occurred a total of 6 times while in motion with risk of causing a wreck due to lack of control to not cause car to stop abruptly in middle of road. shaking has occurred in 4 of the 6 occurrences and car just putters out until it is shut off. determination due to codes read is the throttle bottle- an electrical issue. while the limited power mode may be a safety feature, its interaction with the throttle body/idle issues poses a potential threat. the electrical issue that throttle bodies are experiencing within this make/model needs to be recalled and taken care off effectively and efficiently by ford. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 87156 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in KANSAS CITY, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10473113

FORD FUSION 2010 car safety problem was reported on Aug 30, 2012.FORD FUSION 2010, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . on a routine drive home from work, i exited the highway and noticed my rpms falling faster than what i was controlling with the brake. car was losing speed quickly with no rpms to accelerate it forward to a safe stopping point. was able to pull into a gas station right off highway, but barely as car was apparently entering limited power mode (determined via owners manual). upon placing car into car, dashboard wrench light illuminated. i then turned the car off, sat a minute, restarted car and everything was fine. within the course of the next 10 minutes, the same thing occurred 3 more times and check engine light illuminated. since the first time, this has occurred a total of 6 times while in motion with risk of causing a wreck due to lack of control to not cause car to stop abruptly in middle of road. shaking has occurred in 4 of the 6 occurrences and car just putters out until it is shut off. determination due to codes read is the throttle bottle- an electrical issue. while the limited power mode may be a safety feature, its interaction with the throttle body/idle issues poses a potential threat. the electrical issue that throttle bodies are experiencing within this make/model needs to be recalled and taken care off effectively and efficiently by ford. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 87156 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in KANSAS CITY, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10473206

FORD FUSION 2010 car safety problem was reported on Aug 31, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with VEHICLE SPEED CONTROL . for several weeks i've been noticing a sputter/vibration when in idle or park. this has only happened intermittently. this morning, while driving to work at approximately 65 mph, car suddenly begins to lose power and surge/vibrate/sputter and i notice the wrench light illuminated. i'm completely unable to accelerate and all i can do is coast to a stop on the shoulder of the (very busy) highway. after shutting the car off and sitting for about 15 minutes i'm able to restart the car with no indication there was ever a problem. the car is running smoothly and wrench light is off. i drove it to the nearest dealer's service department where i left it for inspection. as usual, i had to call the service department for an update and was told that the car was not "acting up" and everything seemed to be fine. they did agree to keep it for another round of inspections for the next day or so but i suspect i'll get the same response. after doing some light research, i've discovered that this is a very common issue with the fusions but there is no recall or tsb addressing it. i've read post after post after post written by infuriated fusion owners about this problem. it's time for ford to own up to this, get a solution, and send out the recall notices!!!!!!!!!!!!!!!!!!!!!!!!!!!! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 56500 miles. Ford Fusion 2010 problem was reported in CHATSWORTH, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10473206

FORD FUSION 2010 car safety problem was reported on Aug 31, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . for several weeks i've been noticing a sputter/vibration when in idle or park. this has only happened intermittently. this morning, while driving to work at approximately 65 mph, car suddenly begins to lose power and surge/vibrate/sputter and i notice the wrench light illuminated. i'm completely unable to accelerate and all i can do is coast to a stop on the shoulder of the (very busy) highway. after shutting the car off and sitting for about 15 minutes i'm able to restart the car with no indication there was ever a problem. the car is running smoothly and wrench light is off. i drove it to the nearest dealer's service department where i left it for inspection. as usual, i had to call the service department for an update and was told that the car was not "acting up" and everything seemed to be fine. they did agree to keep it for another round of inspections for the next day or so but i suspect i'll get the same response. after doing some light research, i've discovered that this is a very common issue with the fusions but there is no recall or tsb addressing it. i've read post after post after post written by infuriated fusion owners about this problem. it's time for ford to own up to this, get a solution, and send out the recall notices!!!!!!!!!!!!!!!!!!!!!!!!!!!! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 56500 miles. Ford Fusion 2010 problem was reported in CHATSWORTH, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10473251

FORD FUSION 2010 car safety problem was reported on Sept 01, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with VEHICLE SPEED CONTROL . on a typical good weather day i was driving around running some errands in the city. shortly after i started the car going at a city traffic rate of speed...approx 35-40mph...i got approximately 5miles out and the car began to slow down,and a wrench sign appeared. even with my foot on the accelerator, i could not accelerate, and went to pull off to the side of the rode which i was barely able to do. once i was fully out of the road, i put the car in park, and before i could shut the car off, it began to shake/ vibrate. i turned the car off and let it sit a couple minutes and i proceeded to start the car up, which it did so like the day i bought it, and the wrench sign went away. i proceeded to my first destination with out any problems. i left my destination and proceeded to my next...i got about 3miles out and the car did, and showed the same thing. so as i decided to just head home which was no more than 10 miles away, the car did the same thing 5 more times and the check engine light came on!!!!! i am now home and afraid to drive anywhere. i got online to see what it could possibly be, and i have not been able to call a mechanic because it is of course a holiday weekend!!! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 85000 miles. Ford Fusion 2010 problem was reported in CINCINNATI, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10473251

FORD FUSION 2010 car safety problem was reported on Sept 01, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . on a typical good weather day i was driving around running some errands in the city. shortly after i started the car going at a city traffic rate of speed...approx 35-40mph...i got approximately 5miles out and the car began to slow down,and a wrench sign appeared. even with my foot on the accelerator, i could not accelerate, and went to pull off to the side of the rode which i was barely able to do. once i was fully out of the road, i put the car in park, and before i could shut the car off, it began to shake/ vibrate. i turned the car off and let it sit a couple minutes and i proceeded to start the car up, which it did so like the day i bought it, and the wrench sign went away. i proceeded to my first destination with out any problems. i left my destination and proceeded to my next...i got about 3miles out and the car did, and showed the same thing. so as i decided to just head home which was no more than 10 miles away, the car did the same thing 5 more times and the check engine light came on!!!!! i am now home and afraid to drive anywhere. i got online to see what it could possibly be, and i have not been able to call a mechanic because it is of course a holiday weekend!!! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 85000 miles. Ford Fusion 2010 problem was reported in CINCINNATI, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10473279

FORD FUSION 2010 car safety problem was reported on July 05, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with ENGINE . whle driving my 2010 ford fusion, the car will just stall and cut off while driving with no warning, the engine light and the wrench light comes on, i will turn off the car, wait a few minutes and it will restart, this happens consistantly sometimes as much as 4 times a day, this is definitiely a safety issue because one time when the car stalled, i was almost hit from behind. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 94000 miles. Vehicle Identification Number (VIN):3FAHPOHG5AR. Ford Fusion 2010 problem was reported in WESTLAND, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Engine Review #10473319

FORD FUSION 2010 car safety problem was reported on Sept 01, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with ENGINE . while driving my car on the expressway the wrench light turned on followed by the check engine light. the car started reducing speed even though i was pressing the gas. i pulled over to the side and the car started shaking. i had an obd ii machine in my car at the time and ran a diagnostic. check engine code p2111 came up. after researching the code it says it has to do with the throttle body. i also noticed that there are so many discussion forums out there with people who are having the same issue. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 66500 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in CHICAGO, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10473319

FORD FUSION 2010 car safety problem was reported on Sept 01, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . while driving my car on the expressway the wrench light turned on followed by the check engine light. the car started reducing speed even though i was pressing the gas. i pulled over to the side and the car started shaking. i had an obd ii machine in my car at the time and ran a diagnostic. check engine code p2111 came up. after researching the code it says it has to do with the throttle body. i also noticed that there are so many discussion forums out there with people who are having the same issue. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 66500 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in CHICAGO, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train Review #10473674

FORD FUSION 2010 car safety problem was reported on Mar 20, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . while driving on the highway at about 40 mph the car stalled. all power went off but the electricity stayed on. i rolled to the side and was able to restart after 2-3 tries. the same thing happened when i pulled out of my driveway the same day. ford rebuilt my transmission and gave me a new throttle body. the car ran roughly the other day the engine light came on but it didn't stall. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 28000 miles. Vehicle Identification Number (VIN):3FAHP0CG3AR. Ford Fusion 2010 problem was reported in GREAT NECK, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10473674

FORD FUSION 2010 car safety problem was reported on Mar 20, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with FUEL/PROPULSION SYSTEM . while driving on the highway at about 40 mph the car stalled. all power went off but the electricity stayed on. i rolled to the side and was able to restart after 2-3 tries. the same thing happened when i pulled out of my driveway the same day. ford rebuilt my transmission and gave me a new throttle body. the car ran roughly the other day the engine light came on but it didn't stall. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 28000 miles. Vehicle Identification Number (VIN):3FAHP0CG3AR. Ford Fusion 2010 problem was reported in GREAT NECK, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Tires

Ford Fusion 2010 Tires Review #10473769

FORD FUSION 2010 car safety problem was reported on Aug 31, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with TIRES . tl* the contact owns a 2010 ford fusion. the vehicle was equipped with michelin energy saver a/s green x tires, size 225/50/17. the contact noticed that all four tires exhibited numerous cracks and were completely dry rotted. the vehicle was taken to an independent tire shop where the contact was advised that the tires were not under warranty. the four tires were not replaced. the manufacturer was notified of the defective tires. the approximate failure mileage was 6,300. .Mileage was 6300 miles. Vehicle Identification Number (VIN):3FAHP0HA2AR. Ford Fusion 2010 problem was reported in CAPE CORAL, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10473847

FORD FUSION 2010 car safety problem was reported on May 07, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . transmission is slipping in gear, hesitating during shifts, or coming out of gear completely during acceleration. also the transmission is shimmying down the road in certain gears. the car is getting to the point where it is unsafe to drive and this is my family car. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 55000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in RUSTBURG, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10473926

FORD FUSION 2010 car safety problem was reported on Aug 31, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with FUEL/PROPULSION SYSTEM . loss of accelerator control. wrench and check engine light came on. car entered emergency mode and had to be pulled over and restarted. died 2 more times at highway speed. codes on car from check engine light read p2111 and p2112. dealer completed a throttle body replacement on september 5th, 2012. common problem with these particular vehicles. dealer was awesome with the repair and help with situation. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 46000 miles. Vehicle Identification Number (VIN):3FAHP0JG4AR. Ford Fusion 2010 problem was reported in VANDALIA, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10473926

FORD FUSION 2010 car safety problem was reported on Aug 31, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . loss of accelerator control. wrench and check engine light came on. car entered emergency mode and had to be pulled over and restarted. died 2 more times at highway speed. codes on car from check engine light read p2111 and p2112. dealer completed a throttle body replacement on september 5th, 2012. common problem with these particular vehicles. dealer was awesome with the repair and help with situation. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 46000 miles. Vehicle Identification Number (VIN):3FAHP0JG4AR. Ford Fusion 2010 problem was reported in VANDALIA, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train Review #10474044

FORD FUSION 2010 car safety problem was reported on Sept 04, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . i was driving my vehicle on the highway, at approximately 55-60 mph, when i suddenly lost the ability to accelerate. the car stalled, and the wrench light came on. i had to pull over and restart the car. this happened again, the next day. the car also began to shake prior to turning the car off. i have read hundreds, if not more, complaints regarding this same issue. my car is currently at a local ford dealership, where i was advised that it sounded like the "throttle body". the ford dealer commented that this is a common complaint among the 2010 fusions. again, since discovering this problem, i have read hundreds of complaints online in reference to the same issue. i have filed a complaint with ford, as this part/defect is not covered under my powertrain warranty, even though my vehicle is only two years old, with 58,000 miles. this is a tremendous safety concern, with car losing all ability to accelerate on a busy highway. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 58000 miles. Ford Fusion 2010 problem was reported in CANTON, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10474273

FORD FUSION 2010 car safety problem was reported on Sept 01, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with FUEL/PROPULSION SYSTEM . my 22 year old son and i had made a roundtrip from tallahassee, florida to thomasville, georgia. approximately one and a half or so miles from my house, the rpms on the car began waving wildly, the car jerked slightly, and came to almost a complete stop on the road, with a truck traveling right behind me. i pressed my foot on the accelerator to the floorboard, but the car slowed to a crawl. the truck behind me passed. i managed to keep the car going to my house; we could have walked there faster. again, this was with the accelerator pressed to the floorboard. the "wrench" light came on the dash. i had 55, 187.1 miles on my car, which i bought in april, 2010, new. i researched this (it was labor day weekend and i had no transportation to speak of!). i called the ford dealership; they closed on saturday at 2:00 p.m. they towed my car in on tuesday morning. i told them i suspected a throttle/transmission problem based on what i saw re similar complaints on the internet. i reported this to the national ford website. they took my complaint. the dealer told me the next day that my throttle had failed, and ford would not assist in any payment for replacement. i advised them i was a lawyer, and they are looking at a products liability design defect or tort lawsuit (if someone gets killed when the car dies on the highway). ford could care less. i had to pay $394 for the labor and part. i will never buy another of their cars. this was my 3rd ford. it is not necessarily the money i was concerned about; it seems like there is a design defect that could cause serious personal injury or death, but ford is engaged in a beancounting exercise at this point. remember the pinto? *tr.0 person(s) were injured. 0 person(s) died.Mileage was 55187 miles. Vehicle Identification Number (VIN):3FAHP0HA4AR. Ford Fusion 2010 problem was reported in TALLAHASSEE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.

Ford Fusion 2010 Fuel/propulsion System Review #10474282

FORD FUSION 2010 car safety problem was reported on July 12, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with FUEL/PROPULSION SYSTEM . i purchased a 2010 ford fusion in june and about 3 weeks later, it decelerated and the wrench lit up on the dashboard, while i was driving. luckily, i was not on the highway or this could have caused a serious accident. i pulled over started the car up and it was fine. a few weeks later, i was 2 blocks from my home and the same thing happened 4 times and continues to randomly happen. the time between instances of this occurring can be minutes, hours, days or weeks apart. i have researched the issue and found hundreds if not thousands of complaints and questions regarding the same issue. i was amazed and appalled that such a common and very dangerous issue has not been addressed with a recall. i did purchase the extended warranty only to find out that the warranty does not cover anything that has to do with what is likely to be causing this issue, which is the throttle body. so until i can afford to get this fixed, i am stuck with a car that i am terrified to drive for fear of causing an accident due to the sudden drop in speed. *tr.0 person(s) were injured. 0 person(s) died.Ford Fusion 2010 problem was reported in DALLAS, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10474282

FORD FUSION 2010 car safety problem was reported on July 12, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . i purchased a 2010 ford fusion in june and about 3 weeks later, it decelerated and the wrench lit up on the dashboard, while i was driving. luckily, i was not on the highway or this could have caused a serious accident. i pulled over started the car up and it was fine. a few weeks later, i was 2 blocks from my home and the same thing happened 4 times and continues to randomly happen. the time between instances of this occurring can be minutes, hours, days or weeks apart. i have researched the issue and found hundreds if not thousands of complaints and questions regarding the same issue. i was amazed and appalled that such a common and very dangerous issue has not been addressed with a recall. i did purchase the extended warranty only to find out that the warranty does not cover anything that has to do with what is likely to be causing this issue, which is the throttle body. so until i can afford to get this fixed, i am stuck with a car that i am terrified to drive for fear of causing an accident due to the sudden drop in speed. *tr.0 person(s) were injured. 0 person(s) died.Ford Fusion 2010 problem was reported in DALLAS, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10474507

FORD FUSION 2010 car safety problem was reported on July 19, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with ENGINE . while driving down the road, my engine lost power. rpms went down, and the accelerator was not responsive. i pulled the car to the side of the road, and put it in park. the engine idled very roughly. i shut off the car, waited 5 seconds and attempted to restart. the engine did restart after some effort by the starter. i drove down the road, and the car behaved normally. this seemingly isolated incident increased in frequency in the following weeks. sometimes up to 5 times a day. i took my car to an authorized ford dealer, and the problem was diagnosed as a faulty throttle body. cost of replacement is $355. i researched the problem online and noticed that the problem seems to be fairly common among 2010 ford fusion owners. the online complaints about fusion throttle body problems were exactly the same as the symptoms i experienced. the danger lies in the fact that the car basically stalls without warning and must be restarted before normal driving can resume. i have experienced this problem at both highway and city speeds. a stalled engine in the wrong place at the wrong time (middle of an intersection, freeway, while passing, etc.) could have disastrous effects. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 45000 miles. Ford Fusion 2010 problem was reported in NORTH MANCHESTER, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10474507

FORD FUSION 2010 car safety problem was reported on July 19, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with ELECTRICAL SYSTEM . while driving down the road, my engine lost power. rpms went down, and the accelerator was not responsive. i pulled the car to the side of the road, and put it in park. the engine idled very roughly. i shut off the car, waited 5 seconds and attempted to restart. the engine did restart after some effort by the starter. i drove down the road, and the car behaved normally. this seemingly isolated incident increased in frequency in the following weeks. sometimes up to 5 times a day. i took my car to an authorized ford dealer, and the problem was diagnosed as a faulty throttle body. cost of replacement is $355. i researched the problem online and noticed that the problem seems to be fairly common among 2010 ford fusion owners. the online complaints about fusion throttle body problems were exactly the same as the symptoms i experienced. the danger lies in the fact that the car basically stalls without warning and must be restarted before normal driving can resume. i have experienced this problem at both highway and city speeds. a stalled engine in the wrong place at the wrong time (middle of an intersection, freeway, while passing, etc.) could have disastrous effects. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 45000 miles. Ford Fusion 2010 problem was reported in NORTH MANCHESTER, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10474507

FORD FUSION 2010 car safety problem was reported on July 19, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . while driving down the road, my engine lost power. rpms went down, and the accelerator was not responsive. i pulled the car to the side of the road, and put it in park. the engine idled very roughly. i shut off the car, waited 5 seconds and attempted to restart. the engine did restart after some effort by the starter. i drove down the road, and the car behaved normally. this seemingly isolated incident increased in frequency in the following weeks. sometimes up to 5 times a day. i took my car to an authorized ford dealer, and the problem was diagnosed as a faulty throttle body. cost of replacement is $355. i researched the problem online and noticed that the problem seems to be fairly common among 2010 ford fusion owners. the online complaints about fusion throttle body problems were exactly the same as the symptoms i experienced. the danger lies in the fact that the car basically stalls without warning and must be restarted before normal driving can resume. i have experienced this problem at both highway and city speeds. a stalled engine in the wrong place at the wrong time (middle of an intersection, freeway, while passing, etc.) could have disastrous effects. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 45000 miles. Ford Fusion 2010 problem was reported in NORTH MANCHESTER, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10474513

FORD FUSION 2010 car safety problem was reported on Sept 10, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with FUEL/PROPULSION SYSTEM . was driving in morning traffic on the highway and the car lurched and stalled. car was dead and accelerator would not work. i was able to coast to the shoulder. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 45000 miles. Vehicle Identification Number (VIN):3FAHP0HAXAR. Ford Fusion 2010 problem was reported in CYPRESS, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Electrical System

Ford Fusion 2010 Electrical System Review #10474513

FORD FUSION 2010 car safety problem was reported on Sept 10, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with ELECTRICAL SYSTEM . was driving in morning traffic on the highway and the car lurched and stalled. car was dead and accelerator would not work. i was able to coast to the shoulder. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 45000 miles. Vehicle Identification Number (VIN):3FAHP0HAXAR. Ford Fusion 2010 problem was reported in CYPRESS, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10474513

FORD FUSION 2010 car safety problem was reported on Sept 10, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with ENGINE . was driving in morning traffic on the highway and the car lurched and stalled. car was dead and accelerator would not work. i was able to coast to the shoulder. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 45000 miles. Vehicle Identification Number (VIN):3FAHP0HAXAR. Ford Fusion 2010 problem was reported in CYPRESS, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Engine Review #10474518

FORD FUSION 2010 car safety problem was reported on Sept 08, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with ENGINE . we were traveling on busy i-80 at approximately 70 m.p.h. due to busy vehicular traffic on the interstate hi-way, i was not using the cruise-control. when we experienced the incident, i had pressed on the gas pedal to maintain speed on an uphill section. on the uphill section, i noticed the vehicle did not accelerate and the instrument panel warning lights started flashing. even with heavy traffic, i was able to negotiate maneuvering the vehicle to the shoulder. as i was coasting on the shoulder, i shifted the transmission to neutral and tried to start the engine (ev system did not respond either) with no avail. after coming to a complete stop, i shifted the transmission to park, turned-off the climate control system and the and radio. i removed the ignition key and re-installed it and proceeded to start the vehicle, the propulsion system (ev mode) responded. we accelerated on the shoulder in ev mode and we reached speed the gas engine responded and we were back on i-80 and traveling with the traffic flow. this is first time this has occurred with us but researching this phenoma, this event has happened with other ford fusion hybrid owners. we are concerned the propulsion system may shut-down in an unsafe environment and create a dangerous situation! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 32200 miles. Vehicle Identification Number (VIN):3FADP0L3XAR. Ford Fusion 2010 problem was reported in DES MOINES, IA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: HYBRID ELECTRIC. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10474518

FORD FUSION 2010 car safety problem was reported on Sept 08, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . we were traveling on busy i-80 at approximately 70 m.p.h. due to busy vehicular traffic on the interstate hi-way, i was not using the cruise-control. when we experienced the incident, i had pressed on the gas pedal to maintain speed on an uphill section. on the uphill section, i noticed the vehicle did not accelerate and the instrument panel warning lights started flashing. even with heavy traffic, i was able to negotiate maneuvering the vehicle to the shoulder. as i was coasting on the shoulder, i shifted the transmission to neutral and tried to start the engine (ev system did not respond either) with no avail. after coming to a complete stop, i shifted the transmission to park, turned-off the climate control system and the and radio. i removed the ignition key and re-installed it and proceeded to start the vehicle, the propulsion system (ev mode) responded. we accelerated on the shoulder in ev mode and we reached speed the gas engine responded and we were back on i-80 and traveling with the traffic flow. this is first time this has occurred with us but researching this phenoma, this event has happened with other ford fusion hybrid owners. we are concerned the propulsion system may shut-down in an unsafe environment and create a dangerous situation! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 32200 miles. Vehicle Identification Number (VIN):3FADP0L3XAR. Ford Fusion 2010 problem was reported in DES MOINES, IA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: HYBRID ELECTRIC. VEHICLE SPEED: 70 mph.

Ford Fusion 2010 Power Train Review #10475281

FORD FUSION 2010 car safety problem was reported on Aug 08, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . tl* the contact owns a 2010 ford fusion. the contact stated that the accelerator pedal became inoperable. the vehicle was taken to the dealer for inspection where they stated that the torque converter needed to be replaced. the vehicle was repaired but the failure recurred. the contact took the vehicle back to the dealer where they advised that the power assist warning light was illuminated and that the power steering needed to be replaced. the vehicle was not repaired. the manufacturer was contacted and advised the contact that the vehicle was no longer under warranty. the failure mileage was 53,000. .0 person(s) were injured. 0 person(s) died.Mileage was 53000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in WOODSTOCK, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Steering

Ford Fusion 2010 Steering Review #10475281

FORD FUSION 2010 car safety problem was reported on Aug 08, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with STEERING . tl* the contact owns a 2010 ford fusion. the contact stated that the accelerator pedal became inoperable. the vehicle was taken to the dealer for inspection where they stated that the torque converter needed to be replaced. the vehicle was repaired but the failure recurred. the contact took the vehicle back to the dealer where they advised that the power assist warning light was illuminated and that the power steering needed to be replaced. the vehicle was not repaired. the manufacturer was contacted and advised the contact that the vehicle was no longer under warranty. the failure mileage was 53,000. .0 person(s) were injured. 0 person(s) died.Mileage was 53000 miles. Vehicle Identification Number (VIN):3FAHP0HA8AR. Ford Fusion 2010 problem was reported in WOODSTOCK, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Steering Review #10475717

FORD FUSION 2010 car safety problem was reported on Aug 07, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with STEERING . lost power steering. has happened three times since. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 30000 miles. Ford Fusion 2010 problem was reported in WELLSTON, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 2 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10475878

FORD FUSION 2010 car safety problem was reported on Sept 16, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with ENGINE . the car basically stalled without turning off. the "wrench" light turned on and the car lost all power and the accelerator was unresponsive. the car would only go 2 mph. once stopped and placed in park, the car idled very rough. then turned off the car. when re-starting the car it started poorly, but once started the wrench light was off. the car then drove normally. this happened 3x that day. i am lucky i did not get into an accident when i lost all power and had to pull over. ford will not fix it citing they cannot see the code. i am afraid to drive this car for fear of an accident. *tr *js.0 person(s) were injured. 0 person(s) died.Mileage was 36604 miles. Vehicle Identification Number (VIN):3FAHP0JG1AR. Ford Fusion 2010 problem was reported in SCHENECTADY, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 7 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10475878

FORD FUSION 2010 car safety problem was reported on Sept 16, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . the car basically stalled without turning off. the "wrench" light turned on and the car lost all power and the accelerator was unresponsive. the car would only go 2 mph. once stopped and placed in park, the car idled very rough. then turned off the car. when re-starting the car it started poorly, but once started the wrench light was off. the car then drove normally. this happened 3x that day. i am lucky i did not get into an accident when i lost all power and had to pull over. ford will not fix it citing they cannot see the code. i am afraid to drive this car for fear of an accident. *tr *js.0 person(s) were injured. 0 person(s) died.Mileage was 36604 miles. Vehicle Identification Number (VIN):3FAHP0JG1AR. Ford Fusion 2010 problem was reported in SCHENECTADY, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 7 mph.

Ford Fusion 2010 Power Train Review #10476537

FORD FUSION 2010 car safety problem was reported on Sept 19, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . on way home from work, driving for 30 miles, going 50 mph, upon changing lanes, the acceleration died. wrench light came on. i was able to pull over on the highway. thankfully, just got through the eight miles of construction with no shoulder and only one lane. if it happened then, i could have caused an accident or at least angered quite a few people on their way home from work by stopping traffic with no way to get around me. as the car was idling, the tach was jumping all over the place, so i put it in park and shut the car off. waited a few minutes, started the car and was able to drive the additional mile home. called the dealership to have this checked out. cannot get in for several days. holding my breath driving it back and forth to work on major highways until then. my first major disappointment with ford for not recalling this issue. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 47000 miles. Ford Fusion 2010 problem was reported in BURLINGTON, WI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10476665

FORD FUSION 2010 car safety problem was reported on Sept 20, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact stated that while driving 55 mph and attempting to accelerate, the vehicle would not respond. the vehicle started to shake while decelerating. the contact stopped the vehicle as the wrench warning light illuminated and the failure recurred several times. the vehicle was taken to the dealer who stated that the failure could be related to the throttle body however, a diagnostic was not performed. the manufacturer was not made aware of the failure. the approximate failure and current mileage was 74,300. .0 person(s) were injured. 0 person(s) died.Mileage was 74300 miles. Vehicle Identification Number (VIN):3FAHP0HAXAR. Ford Fusion 2010 problem was reported in HATTIESBURG, MS. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10476739

FORD FUSION 2010 car safety problem was reported on Sept 19, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with ENGINE . i was driving my 2010 fusion down the highway when the car began to lose power and the check engine light came on. the rpm's increased when i pressed the gas pedal, but the car continued to slow down. luckily, i was able to pull over to the shoulder. after shutting the car off and waiting a minute, i was able to restart and continue with no issues. it happened again 2 days later. after running a google search, i found that there are plenty of other fusion owners with the same issue. i hope ford is able to rectify this issue before someone gets hurt. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 47000 miles. Ford Fusion 2010 problem was reported in ALPHARETTA, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Ford Fusion 2010 Air Bags

Ford Fusion 2010 Air Bags Review #10476844

FORD FUSION 2010 car safety problem was reported on Sept 12, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with AIR BAGS . tl* the contact owns a 2010 ford fusion. the contact was in traffic and neither the brake pedal nor the accelerator pedal was depressed when the vehicle began to roll forward. immediately, the vehicle abnormally accelerated to 35 mph. the contact attempted to control the unintended acceleration but the steering wheel and the brakes had become operable. as a result, the contact crashed into another vehicle. the air bags failed to deploy and the front driver side seat belt did not restrain the contact properly. the contact sustained a fractured toe, a bruised sternum and bruising to the forehead. the police reported to the scene and a police report was filed. the contact was transported to the hospital via ambulance. the police inspected the vehicle but could not determine the cause of the failure. the vehicle was towed to a collision center and the manufacturer was made aware of the failure. the manufacturer advised the contact that an engineer would be sent to inspect the vehicle. prior to the crash, the contact noticed slight surging and had taken to the vehicle to the dealer for diagnostic testing where the technician recalibrated the computer. the vehicle was not repaired. the approximate failure mileage was 36,000. .Vehicle was involved in a crash. 1 person(s) were injured. 0 person(s) died.Mileage was 36000 miles. Vehicle Identification Number (VIN):3FAHP0JA7AR. Ford Fusion 2010 problem was reported in COVINA, CA. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Seat Belts

Ford Fusion 2010 Seat Belts Review #10476844

FORD FUSION 2010 car safety problem was reported on Sept 12, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with SEAT BELTS . tl* the contact owns a 2010 ford fusion. the contact was in traffic and neither the brake pedal nor the accelerator pedal was depressed when the vehicle began to roll forward. immediately, the vehicle abnormally accelerated to 35 mph. the contact attempted to control the unintended acceleration but the steering wheel and the brakes had become operable. as a result, the contact crashed into another vehicle. the air bags failed to deploy and the front driver side seat belt did not restrain the contact properly. the contact sustained a fractured toe, a bruised sternum and bruising to the forehead. the police reported to the scene and a police report was filed. the contact was transported to the hospital via ambulance. the police inspected the vehicle but could not determine the cause of the failure. the vehicle was towed to a collision center and the manufacturer was made aware of the failure. the manufacturer advised the contact that an engineer would be sent to inspect the vehicle. prior to the crash, the contact noticed slight surging and had taken to the vehicle to the dealer for diagnostic testing where the technician recalibrated the computer. the vehicle was not repaired. the approximate failure mileage was 36,000. .Vehicle was involved in a crash. 1 person(s) were injured. 0 person(s) died.Mileage was 36000 miles. Vehicle Identification Number (VIN):3FAHP0JA7AR. Ford Fusion 2010 problem was reported in COVINA, CA. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Vehicle Speed Control

Ford Fusion 2010 Vehicle Speed Control Review #10476844

FORD FUSION 2010 car safety problem was reported on Sept 12, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 ford fusion. the contact was in traffic and neither the brake pedal nor the accelerator pedal was depressed when the vehicle began to roll forward. immediately, the vehicle abnormally accelerated to 35 mph. the contact attempted to control the unintended acceleration but the steering wheel and the brakes had become operable. as a result, the contact crashed into another vehicle. the air bags failed to deploy and the front driver side seat belt did not restrain the contact properly. the contact sustained a fractured toe, a bruised sternum and bruising to the forehead. the police reported to the scene and a police report was filed. the contact was transported to the hospital via ambulance. the police inspected the vehicle but could not determine the cause of the failure. the vehicle was towed to a collision center and the manufacturer was made aware of the failure. the manufacturer advised the contact that an engineer would be sent to inspect the vehicle. prior to the crash, the contact noticed slight surging and had taken to the vehicle to the dealer for diagnostic testing where the technician recalibrated the computer. the vehicle was not repaired. the approximate failure mileage was 36,000. .Vehicle was involved in a crash. 1 person(s) were injured. 0 person(s) died.Mileage was 36000 miles. Vehicle Identification Number (VIN):3FAHP0JA7AR. Ford Fusion 2010 problem was reported in COVINA, CA. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10477023

FORD FUSION 2010 car safety problem was reported on Sept 24, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . i have a 2010 fusion. i purchased the car as a certified pre-owned. the car stalled 6 times on the way home last night. the wrench light would go on and there was no throttle response. the car would shake and sputter. i would shut the car off and restart and could proceed for a short distance. the last time it stall on the freeway on ramp. i took it in and let the dealer know what had occurred and they called back indicating it is the throttle body. i am out of manufacturers warranty. the cost is $500. the power train system is covered but the throttle body is not (even though the throttle body causes the power train to go into stall)? at what point will they make the choice that the throttle body that is in these cars are not up to par and a safety hazard and make it a recalled item? *tr.0 person(s) were injured. 0 person(s) died.Mileage was 45467 miles. Vehicle Identification Number (VIN):3FAHP0HG2AR. Ford Fusion 2010 problem was reported in FITCHBURG, WI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10477023

FORD FUSION 2010 car safety problem was reported on Sept 24, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with FUEL/PROPULSION SYSTEM . i have a 2010 fusion. i purchased the car as a certified pre-owned. the car stalled 6 times on the way home last night. the wrench light would go on and there was no throttle response. the car would shake and sputter. i would shut the car off and restart and could proceed for a short distance. the last time it stall on the freeway on ramp. i took it in and let the dealer know what had occurred and they called back indicating it is the throttle body. i am out of manufacturers warranty. the cost is $500. the power train system is covered but the throttle body is not (even though the throttle body causes the power train to go into stall)? at what point will they make the choice that the throttle body that is in these cars are not up to par and a safety hazard and make it a recalled item? *tr.0 person(s) were injured. 0 person(s) died.Mileage was 45467 miles. Vehicle Identification Number (VIN):3FAHP0HG2AR. Ford Fusion 2010 problem was reported in FITCHBURG, WI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 45 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10477067

FORD FUSION 2010 car safety problem was reported on Sept 21, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . i was slowing to a stop when my car shuddered and the engine seemed to die. i had a error symbol for the transmission and the engine had no more power. it was stuck in idle now even though i was just doing 35 miles per hour coming to a stop. as i finally braked to a stop the engine was surging, but when i pressed the gas pedal, nothing happened to the engine, it was as if it was just turned on and placed in drive only. i didn't know what to do, i had to get through 2 intersections on idle speed only. i finally pulled over past the intersections and turned my car completely off. i then turned it back on and it was working normally. i took it to the ford dealership, who told me this is common after a new battery is placed in these fusions. they noticed my recently purchased used car (purchased about a month before this) had a brand new battery in it. they told me with a new battery, the carbon builds up dramatically and damages the throttle body. so i need to buy a new throttle body and have the cars acceleration computer reprogrammed. and this might happen every time i get a new battery? please investigate this occurrence with other ford dealerships. i have reading this same story all over the web. why doesn't ford do something to correct this issue? *tr.0 person(s) were injured. 0 person(s) died.Mileage was 51121 miles. Vehicle Identification Number (VIN):3FAHP0CG5AR. Ford Fusion 2010 problem was reported in FRISCO, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10477067

FORD FUSION 2010 car safety problem was reported on Sept 21, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with FUEL/PROPULSION SYSTEM . i was slowing to a stop when my car shuddered and the engine seemed to die. i had a error symbol for the transmission and the engine had no more power. it was stuck in idle now even though i was just doing 35 miles per hour coming to a stop. as i finally braked to a stop the engine was surging, but when i pressed the gas pedal, nothing happened to the engine, it was as if it was just turned on and placed in drive only. i didn't know what to do, i had to get through 2 intersections on idle speed only. i finally pulled over past the intersections and turned my car completely off. i then turned it back on and it was working normally. i took it to the ford dealership, who told me this is common after a new battery is placed in these fusions. they noticed my recently purchased used car (purchased about a month before this) had a brand new battery in it. they told me with a new battery, the carbon builds up dramatically and damages the throttle body. so i need to buy a new throttle body and have the cars acceleration computer reprogrammed. and this might happen every time i get a new battery? please investigate this occurrence with other ford dealerships. i have reading this same story all over the web. why doesn't ford do something to correct this issue? *tr.0 person(s) were injured. 0 person(s) died.Mileage was 51121 miles. Vehicle Identification Number (VIN):3FAHP0CG5AR. Ford Fusion 2010 problem was reported in FRISCO, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10477092

FORD FUSION 2010 car safety problem was reported on Sept 17, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . i recently bought a 2010 ford fusion with 45000.00 miles on it. after having owned it for only about 2.5 months i am having problems. while driving down a 4 lane highway at 55 miles per hour it almost stops in the middle of the highway and will not accelerate. it does this with no warning. i am able to pull over to the shoulder and the car begins to shake as i come to a complete stop. once i turn the car off the wrench light goes out i am able to start it back up. it has happened several more times. today it happened in the middle of a busy intersection. the ford dealership in my area when i called said it would be hard to diagnose because the problem is intermittent. by reading the complaints from everyone on the 2010 ford fusion this a common problem with this model. the issue seems to be the throttle body. my fear is that someone will slam into my car not realizing it has stopped in the road. i really think it is a safety issue and cannot believe with being such a wide spread problem ford has not done something to correct it before someone is injured from what appears to be a defective part they have put on their cars. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 48595 miles. Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in ANDERSON, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 50 mph.

Ford Fusion 2010 Power Train Review #10477093

FORD FUSION 2010 car safety problem was reported on Sept 22, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . i was traveling down the highway when my car stopped getting power when i pressed the gas. a yellow wrench warning dash light came on, the car started shaking and had no power when trying to accelerate to get over a lane to get off the road to avoid an accident. i luckily got over with my hazard lights on and coasted to the shoulder where the car finally stopped but did not shut off or die. the car idled and continued to shake so i popped the hood and checked the transmission fluid level. the level was slightly low which was strange cause i had to add half a qt of trans fluid the month before because the shifting was rough. the fluid was very dark colored and smelled scorched. i shut the vehicle off and let it sit for about 10 minutes then i checked the oil, ok. i turned the car back on, added a little more trans fluid and the car seemed to be ok to get me the rest of the way to work. i left it in a parking lot for the night and returned to check it out in the light. i jacked it up and found some fluid slowly coming out of the place where the axle goes into the transmission. i called the ford service center, explained what happened and explained what i found. i had the recall for the transmission done in 2011 for ford fusion 2010s but the rough shifting has been a problem since i bought it. i have had constant trouble with the transmission shifting rough and now losing all power while driving on the highway at 55mph. it almost caused an accident. my car is now at 76,800 miles and ford service rep says the bill is on me cause the powertrain warranty is up and the recall for the same problem doesn't cover me anymore. i want my car fixed with this problem and i cant afford to keep going to the shop every time this keeps acting up. ford needs to fix the problem with their transmissions before someone gets hurt by this. luckily my 1yr old daughter was not with me this time. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 76800 miles. Vehicle Identification Number (VIN):3FAHP0HA3AR. Ford Fusion 2010 problem was reported in DURHAM, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10477193

FORD FUSION 2010 car safety problem was reported on Sept 25, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with ENGINE . i pulled out of my works parking lot and got 50 ft. car began to slow down, shake/ vibrate violently, and emergency wrench lite lit up. while driving and while in park, it shook. i went to pull off to the side of the rode safely. thank good ness i was on a downhill and could coast to a side road (but still not safe where i was). once i was pulled off major road, i put the car in park. i turned the car off and was too afraid to do anything else. i called for a tow. 24 hours later, i was told my car's computer code said it had a bad throttle body. it was replaced with a brand new, revised throttle body - under warranty which ends in 37 days. it happens to many ford fusions. it's time for ford to own up and send out the recall notices before someone gets hurt/killed. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 27150 miles. Vehicle Identification Number (VIN):3FAHP0GA4AR. Ford Fusion 2010 problem was reported in HAMILTON, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10477193

FORD FUSION 2010 car safety problem was reported on Sept 25, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . i pulled out of my works parking lot and got 50 ft. car began to slow down, shake/ vibrate violently, and emergency wrench lite lit up. while driving and while in park, it shook. i went to pull off to the side of the rode safely. thank good ness i was on a downhill and could coast to a side road (but still not safe where i was). once i was pulled off major road, i put the car in park. i turned the car off and was too afraid to do anything else. i called for a tow. 24 hours later, i was told my car's computer code said it had a bad throttle body. it was replaced with a brand new, revised throttle body - under warranty which ends in 37 days. it happens to many ford fusions. it's time for ford to own up and send out the recall notices before someone gets hurt/killed. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 27150 miles. Vehicle Identification Number (VIN):3FAHP0GA4AR. Ford Fusion 2010 problem was reported in HAMILTON, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 30 mph.

Ford Fusion 2010 Power Train Review #10478057

FORD FUSION 2010 car safety problem was reported on Sept 28, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . wrench light comes on, car kicks out of gear into idling mode, will not accelerate, shakes violently. pull over, turn it off, restart it with no problems. sluggish gear changes (automatic) happens at town and highway speed. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 30300 miles. Vehicle Identification Number (VIN):3FAHP0HA0AR. Ford Fusion 2010 problem was reported in MUNFORD, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 10 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10478213

FORD FUSION 2010 car safety problem was reported on Sept 30, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with FUEL/PROPULSION SYSTEM . throttle body malfunctions while car is at speed. the "wrench" light appears on the display and then the car loses power and begins to shudder. turning the car off and restarting it resets the display and starts fine. problem is intermittent but dangerous as the car stops working while the car is going anywhere from 25 to 45 mph. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 39000 miles. Ford Fusion 2010 problem was reported in W HOLLYWOOD, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10478213

FORD FUSION 2010 car safety problem was reported on Sept 30, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . throttle body malfunctions while car is at speed. the "wrench" light appears on the display and then the car loses power and begins to shudder. turning the car off and restarting it resets the display and starts fine. problem is intermittent but dangerous as the car stops working while the car is going anywhere from 25 to 45 mph. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 39000 miles. Ford Fusion 2010 problem was reported in W HOLLYWOOD, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Ford Fusion 2010 Power Train Review #10478490

FORD FUSION 2010 car safety problem was reported on Sept 30, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . wrench light comes on, car kicks out of gear into idle mode, will not accelerate, shakes violently. i was able to coast to side of road and turn off engine. restarted engine with longer than normal cranking time. gear changes (automatic) continues to be sluggish and happens at highway and city speeds. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 51000 miles. Vehicle Identification Number (VIN):3FAHP0JG3AR. Ford Fusion 2010 problem was reported in PINEHURST, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 55 mph.

Ford Fusion 2010 Structure Body

Ford Fusion 2010 Structure Body Review #10478601

FORD FUSION 2010 car safety problem was reported on Sept 04, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with STRUCTURE:BODY . tl* the contact owns a 2010 ford fusion. the contact stated that while entering the vehicle the interior drivers side door handle detached. the vehicle was taken to the dealer who stated that the door handle needed to be replaced. the manufacturer was made aware of the failure. the vehicle was not repaired. the failure and current mileage was 50,000. .0 person(s) were injured. 0 person(s) died.Mileage was 50000 miles. Vehicle Identification Number (VIN):3FAHP0HA4AR. Ford Fusion 2010 problem was reported in SOUTH LION, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Fusion 2010 Engine

Ford Fusion 2010 Engine Review #10478691

FORD FUSION 2010 car safety problem was reported on Oct 04, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with ENGINE . at 11:45 pm, i was traveling west on i-64, at 68 mph, when my car quickly decelerated. despite my applying more gas, my car continued to lose power rapidly and began shuddering. it was then that the "wrench" warning light came on. i immediately pulled over to the side of the road, turned my vehicle off and put my hazard lights on. i waited for a 5 minutes before starting the car again. the car started roughly but did not have any power and could/would not accelerate. it was at this time that both the wrench and engine warning lights came on. again i turned off the car and waited. after another 10-15 minutes, i turned the car on again. this time it started without incident. the wrench warning light did not come back on but the engine light remained on. i kept my hazard lights on and remained in the breakdown lane while i drove approximately 5 miles to the closest exit off the interstate where i promptly parked my car. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 89000 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in SANDY HOOK, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 68 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10478691

FORD FUSION 2010 car safety problem was reported on Oct 04, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . at 11:45 pm, i was traveling west on i-64, at 68 mph, when my car quickly decelerated. despite my applying more gas, my car continued to lose power rapidly and began shuddering. it was then that the "wrench" warning light came on. i immediately pulled over to the side of the road, turned my vehicle off and put my hazard lights on. i waited for a 5 minutes before starting the car again. the car started roughly but did not have any power and could/would not accelerate. it was at this time that both the wrench and engine warning lights came on. again i turned off the car and waited. after another 10-15 minutes, i turned the car on again. this time it started without incident. the wrench warning light did not come back on but the engine light remained on. i kept my hazard lights on and remained in the breakdown lane while i drove approximately 5 miles to the closest exit off the interstate where i promptly parked my car. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 89000 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in SANDY HOOK, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 68 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10478691

FORD FUSION 2010 car safety problem was reported on Oct 04, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with FUEL/PROPULSION SYSTEM . at 11:45 pm, i was traveling west on i-64, at 68 mph, when my car quickly decelerated. despite my applying more gas, my car continued to lose power rapidly and began shuddering. it was then that the "wrench" warning light came on. i immediately pulled over to the side of the road, turned my vehicle off and put my hazard lights on. i waited for a 5 minutes before starting the car again. the car started roughly but did not have any power and could/would not accelerate. it was at this time that both the wrench and engine warning lights came on. again i turned off the car and waited. after another 10-15 minutes, i turned the car on again. this time it started without incident. the wrench warning light did not come back on but the engine light remained on. i kept my hazard lights on and remained in the breakdown lane while i drove approximately 5 miles to the closest exit off the interstate where i promptly parked my car. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 89000 miles. Vehicle Identification Number (VIN):3FAHP0HA7AR. Ford Fusion 2010 problem was reported in SANDY HOOK, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 68 mph.

Ford Fusion 2010 Fuel/propulsion System Review #10478756

FORD FUSION 2010 car safety problem was reported on Oct 04, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with FUEL/PROPULSION SYSTEM . i own a 2010 ford fusion with 19000 miles. i haven't even had it a month yet. it is a certified pre-owned vehicle. driving home from work yesterday, i stopped in a line of traffic at a red light. the light turned green and i accelerated. during acceleration, the car jerked then lost all forward momentum and "puttered". i was able to "putter" to the side of the road out of traffic. i put it in park and noticed that the wrench light was lit up, so i pulled out the owner's manual to see what it meant...powertrain. i turned the car off for about 5 minutes then restarted it with no other incidents on my way home. thank god i wasn't in any heavier traffic or multiple lanes! from what i've been reading, some people have lost acceleration going 50+ mph in interstate/highway traffic! if this problem isn't addressed, and soon, someone will be seriously injured or worse due to a defect in ford's design. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 19000 miles. Vehicle Identification Number (VIN):3FAHP0JG7AR. Ford Fusion 2010 problem was reported in MEDINA, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10478756

FORD FUSION 2010 car safety problem was reported on Oct 04, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . i own a 2010 ford fusion with 19000 miles. i haven't even had it a month yet. it is a certified pre-owned vehicle. driving home from work yesterday, i stopped in a line of traffic at a red light. the light turned green and i accelerated. during acceleration, the car jerked then lost all forward momentum and "puttered". i was able to "putter" to the side of the road out of traffic. i put it in park and noticed that the wrench light was lit up, so i pulled out the owner's manual to see what it meant...powertrain. i turned the car off for about 5 minutes then restarted it with no other incidents on my way home. thank god i wasn't in any heavier traffic or multiple lanes! from what i've been reading, some people have lost acceleration going 50+ mph in interstate/highway traffic! if this problem isn't addressed, and soon, someone will be seriously injured or worse due to a defect in ford's design. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 19000 miles. Vehicle Identification Number (VIN):3FAHP0JG7AR. Ford Fusion 2010 problem was reported in MEDINA, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 0 mph.

Ford Fusion 2010 Steering Hydraulic Power Assist System

Ford Fusion 2010 Steering Hydraulic Power Assist System Review #10478781

FORD FUSION 2010 car safety problem was reported on Oct 04, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with STEERING:HYDRAULIC POWER ASSIST SYSTEM . on october 4, 2012, i was driving my 2010 ford fusion around 40 m.p.h. on a four lane street when the power steering failed/locked for no reason. the electronic display said "power steering assist fault. service advancetrac" i drove straight for 5 miles and knew there was a dealer on the left side and managed a wide left turn into the dealership. when i waited for the representative to come to my car, i turned off the engine. i explained what happened and he asked to see the display. i turned the car back on, the display was gone and the power steering was back on. i left the dealer and went on-line and found numerous complaints about the same problem. i also learned that it is useless to take the car to ford for service because dealers claim that the computer is not showing a diagnostic code and they need to "replicate the problem" (which is highly unlikely that it will happen while at the dealer). i also learned that it has happened to some customers many times and there is no warning or reason why the ps suddenly fails. further, it appears that dealers have no idea how to correct the problem. it is a safety issue. it is dangerous, especially if it fails when trying to make a turn. i went back to the dealer and was told that they never heard of this issue and it could be anything. i then called corporate headquarters for ford and filed a complaint. i was told that they would get back to me today, october 5, 2012. i have heard nothing. this needs to be investigated immediately. i cannot afford to buy a new car. i also cannot in good conscience sell my car with this dangerous defect. i feel that ford is forcing me to drive an unsafe car and i am extremely scared that the ps will go out again in a situation that will cause me to crash or worse. *tr the consumer stated the dealer replaced the steering rack. the consumer stated the power steering has not failed since. however, the vehicle seemed to steer hard and would pull to the left or right when braking. also, a seal from the transmission was leaking fluid, which needed to be replaced. .0 person(s) were injured. 0 person(s) died.Mileage was 49700 miles. Vehicle Identification Number (VIN):3FAHP0JA7AR. Ford Fusion 2010 problem was reported in ROYAL OAK, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 40 mph. DEALER'S NAME: ROYAL OAK FORD . DEALER'S CITY: ROYAL OAK . DEALER'S STATE CODE: MI. DEALER'S ZIPCODE: 48067 .

Ford Fusion 2010 Steering Rack And Pinion Rack

Ford Fusion 2010 Steering Rack And Pinion Rack Review #10478781

FORD FUSION 2010 car safety problem was reported on Oct 04, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with STEERING:RACK AND PINION:RACK . on october 4, 2012, i was driving my 2010 ford fusion around 40 m.p.h. on a four lane street when the power steering failed/locked for no reason. the electronic display said "power steering assist fault. service advancetrac" i drove straight for 5 miles and knew there was a dealer on the left side and managed a wide left turn into the dealership. when i waited for the representative to come to my car, i turned off the engine. i explained what happened and he asked to see the display. i turned the car back on, the display was gone and the power steering was back on. i left the dealer and went on-line and found numerous complaints about the same problem. i also learned that it is useless to take the car to ford for service because dealers claim that the computer is not showing a diagnostic code and they need to "replicate the problem" (which is highly unlikely that it will happen while at the dealer). i also learned that it has happened to some customers many times and there is no warning or reason why the ps suddenly fails. further, it appears that dealers have no idea how to correct the problem. it is a safety issue. it is dangerous, especially if it fails when trying to make a turn. i went back to the dealer and was told that they never heard of this issue and it could be anything. i then called corporate headquarters for ford and filed a complaint. i was told that they would get back to me today, october 5, 2012. i have heard nothing. this needs to be investigated immediately. i cannot afford to buy a new car. i also cannot in good conscience sell my car with this dangerous defect. i feel that ford is forcing me to drive an unsafe car and i am extremely scared that the ps will go out again in a situation that will cause me to crash or worse. *tr the consumer stated the dealer replaced the steering rack. the consumer stated the power steering has not failed since. however, the vehicle seemed to steer hard and would pull to the left or right when braking. also, a seal from the transmission was leaking fluid, which needed to be replaced. .0 person(s) were injured. 0 person(s) died.Mileage was 49700 miles. Vehicle Identification Number (VIN):3FAHP0JA7AR. Ford Fusion 2010 problem was reported in ROYAL OAK, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 40 mph. DEALER'S NAME: ROYAL OAK FORD . DEALER'S CITY: ROYAL OAK . DEALER'S STATE CODE: MI. DEALER'S ZIPCODE: 48067 .

Ford Fusion 2010 Power Train Axle Assembly Axle Shaft Seal

Ford Fusion 2010 Power Train Axle Assembly Axle Shaft Seal Review #10478781

FORD FUSION 2010 car safety problem was reported on Oct 04, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT:SEAL . on october 4, 2012, i was driving my 2010 ford fusion around 40 m.p.h. on a four lane street when the power steering failed/locked for no reason. the electronic display said "power steering assist fault. service advancetrac" i drove straight for 5 miles and knew there was a dealer on the left side and managed a wide left turn into the dealership. when i waited for the representative to come to my car, i turned off the engine. i explained what happened and he asked to see the display. i turned the car back on, the display was gone and the power steering was back on. i left the dealer and went on-line and found numerous complaints about the same problem. i also learned that it is useless to take the car to ford for service because dealers claim that the computer is not showing a diagnostic code and they need to "replicate the problem" (which is highly unlikely that it will happen while at the dealer). i also learned that it has happened to some customers many times and there is no warning or reason why the ps suddenly fails. further, it appears that dealers have no idea how to correct the problem. it is a safety issue. it is dangerous, especially if it fails when trying to make a turn. i went back to the dealer and was told that they never heard of this issue and it could be anything. i then called corporate headquarters for ford and filed a complaint. i was told that they would get back to me today, october 5, 2012. i have heard nothing. this needs to be investigated immediately. i cannot afford to buy a new car. i also cannot in good conscience sell my car with this dangerous defect. i feel that ford is forcing me to drive an unsafe car and i am extremely scared that the ps will go out again in a situation that will cause me to crash or worse. *tr the consumer stated the dealer replaced the steering rack. the consumer stated the power steering has not failed since. however, the vehicle seemed to steer hard and would pull to the left or right when braking. also, a seal from the transmission was leaking fluid, which needed to be replaced. .0 person(s) were injured. 0 person(s) died.Mileage was 49700 miles. Vehicle Identification Number (VIN):3FAHP0JA7AR. Ford Fusion 2010 problem was reported in ROYAL OAK, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Ford Fusion 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Fusion 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 40 mph. DEALER'S NAME: ROYAL OAK FORD . DEALER'S CITY: ROYAL OAK . DEALER'S STATE CODE: MI. DEALER'S ZIPCODE: 48067 .

Ford Fusion 2010 Power Train Review #10478833

FORD FUSION 2010 car safety problem was reported on Oct 01, 2011.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . traveling on the street at about 40 mph, car shuddered to a stop. engine light came on. had car towed home. car started the next day. carefully drove the car to the ford dealer. they replaced the throttle body. the throttle body should not be failing at 60000 miles. this should be a recall. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 60000 miles. Vehicle Identification Number (VIN):3FAHP0HA2AR. Ford Fusion 2010 problem was reported in CARLSBAD, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Fuel/propulsion System

Ford Fusion 2010 Fuel/propulsion System Review #10478833

FORD FUSION 2010 car safety problem was reported on Oct 01, 2011.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with FUEL/PROPULSION SYSTEM . traveling on the street at about 40 mph, car shuddered to a stop. engine light came on. had car towed home. car started the next day. carefully drove the car to the ford dealer. they replaced the throttle body. the throttle body should not be failing at 60000 miles. this should be a recall. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 60000 miles. Vehicle Identification Number (VIN):3FAHP0HA2AR. Ford Fusion 2010 problem was reported in CARLSBAD, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Ford Fusion 2010 Power Train

Ford Fusion 2010 Power Train Review #10479222

FORD FUSION 2010 car safety problem was reported on Oct 06, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with POWER TRAIN . this is my second complaint in as many days - about the exact same problem. this incident happened two days after the first one. traveling on a city street approximately 15-20 mph and the car suddenly loses all acceleration and the wrench light appears. i was able to putter to the side of the road and shut the car off. when i restarted it, it ran fine. it goes to the dealer today for inspection, where i suspect i'll get the same response that most every one else gets - that the problem couldn't be re-produced. what will it take to get a recall from ford about the defect in their design? fatal accidents?? that's a pretty high price to pay before they're forced to correct their product. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 190000 miles. Vehicle Identification Number (VIN):3FAHP0JG7AR. Ford Fusion 2010 problem was reported in MEDINA, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 15 mph.

Ford Fusion 2010 Unknown Or Other

Ford Fusion 2010 Unknown Or Other Review #10479222

FORD FUSION 2010 car safety problem was reported on Oct 06, 2012.FORD FUSION 2010, manufactured by Ford Motor Company had a problem with UNKNOWN OR OTHER . this is my second complaint in as many days - about the exact same problem. this incident happened two days after the first one. traveling on a city street approximately 15-20 mph and the car suddenly loses all acceleration and the wrench light appears. i was able to putter to the side of the road and shut the car off. when i restarted it, it ran fine. it goes to the dea