FORD CROWN VICTORIA 1993

Report Your FORD CROWN VICTORIA Problem or Post a Question

No comments have been provided.

My turn signals have failed to work on my 1998 Crown Victoria. What could be the problem?

blow back when filling gas tank 1998 ford crown victoria

please contact \

paulttq@yahoo.com

The middle rear seat belt in my 1989 Crown Victoria does not function.  It has only the  female belt and the male belt is completely missing no return spring that I can feel.   Can I get a replacement from
my local Ford Dealer?

my 2004 crown victoria has a electrical problem. The wire behind my interior fuse panel has fried. leaving me with no headlights dash light dome light or taillights. hazards and signals come on but dont blink and also brake lights come on. how can

I recently purchased a 2003 Crown Victoria. The vehicle has a very dangerous problem. When the windshield wipers are used, they will periodically stop working and the windshield wiper fluid will activate on its own. It will then continue to spr

My 2000 Ford Crown Victoria in automatic transmission slip in uphill what is the problem.please reply i park the car on the street thankyou for advanced

While driving at night in my 2003 Crown Victoria LX, I was turning on to a on ramp when my low beams went out. I had to pull off   the road. I turned the lights switch to being on manually, but nothing happened. After a few minutes, they came ba

where does the small wire from the starter go to on a 1993 ford crown victoria?

FORD CROWN VICTORIA Power Train Automatic Transmission Control Module (tcm, Pcm)

FORD CROWN VICTORIA 1993 Safety Review #461818

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 10, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM, PCM) . TRACTION CONTROL SYSTEM ACTIVATED WHEN ATTEMTING TO GO UP A SNOWY/SLIPPERY HILL, CAUSING VEHICLE TO LOSE CONTROL/SKID SIDEWAYS. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W6PX. FORD CROWN VICTORIA 1993 problem was reported in BUFFALO, NY. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #476817

FORD CROWN VICTORIA 1993 car safety problem was reported on Dec 06, 1994.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with COMMUNICATIONS:HORN ASSEMBLY . LOCATION AND SIZE OF HORN BUTTON CAUSES DIFFICULTY IN LOCATING AND DEPRESSING BUTTON DURING EMERGENCY SITUATIONS. *SKD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74WXPX. FORD CROWN VICTORIA 1993 problem was reported in HUMMELSTOW, PA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #476583

FORD CROWN VICTORIA 1993 car safety problem was reported on Nov 22, 1994.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:ROTOR . DEFECTIVE BRAKE ROTORS CAUSED VEHICLE TO VIBRATE WHEN BRAKING. *SKD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP74W5PX. FORD CROWN VICTORIA 1993 problem was reported in NORTON, OH. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #960871

FORD CROWN VICTORIA 1993 car safety problem was reported on Sept 01, 1994.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SEAT BELTS:FRONT:RETRACTOR . FRONT SEAT LAP/SHOULDER WILL NOT RETRACT. TT.0 person(s) were injured. 0 person(s) died.FORD CROWN VICTORIA 1993 problem was reported in HAMILTON, IN. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #480839

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 16, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . THROTTLE POSITION SENSOR FAILED, CAUSING VEHICLE TO HESITATE/BUCK/JERK/SURGE. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W6PY. FORD CROWN VICTORIA 1993 problem was reported in VIENNA, VA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #480839

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 16, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM . CHECK ENGINE LIGHT CAME ON, INDICATING ENGINE PROBLEM/REPLACED AIR BYPASS ASSEMBLY TO REMEDY PROBLEM..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W6PY. FORD CROWN VICTORIA 1993 problem was reported in VIENNA, VA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #961924

FORD CROWN VICTORIA 1993 car safety problem was reported on Mar 14, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC . REAR DISC BRAKES FAILURE, BRAKES DONT WORK. TT.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP74W4PX. FORD CROWN VICTORIA 1993 problem was reported in LOWELL, MA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #481699

FORD CROWN VICTORIA 1993 car safety problem was reported on Feb 14, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with AIR BAGS:FRONTAL . OTHER: LOCATION OF PASSENGER'S AIR BAG WHEN DEPLOYED, RESULTED IN REARVIEW MIRROR BEING TORN AND THROWN AT PASSENGER, RESULTING IN INJURY. *SKD.Vehicle was involved in a crash. 1 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W6PX. FORD CROWN VICTORIA 1993 problem was reported in ISLAMORADA, FL. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #489603

FORD CROWN VICTORIA 1993 car safety problem was reported on Apr 23, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS . BRAKE LINE RUBBING AGAINST FRAME, CAUSING BRAKE LINE FAILURE. *SKD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP71W1PX. FORD CROWN VICTORIA 1993 problem was reported in SOUTH LAKE, CA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #968660

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS . THE BRAKES GRIND AND ARE VERY NOISY. PLEASE DESCRIBE. *AK.0 person(s) were injured. 0 person(s) died.FORD CROWN VICTORIA 1993 problem was reported in BURNSVILLE, NC. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #969414

FORD CROWN VICTORIA 1993 car safety problem was reported on May 18, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:CALIPER . ABS, BRAKE FAILURE , REPLACEMENT OF DISC ROTORS AND PADS, CALIPERS IN FRONT AND REAR. TT.0 person(s) were injured. 0 person(s) died.FORD CROWN VICTORIA 1993 problem was reported in HUDSON, ME. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #969414

FORD CROWN VICTORIA 1993 car safety problem was reported on May 18, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:ROTOR . ABS, BRAKE FAILURE , REPLACEMENT OF DISC ROTORS AND PADS, CALIPERS IN FRONT AND REAR. TT.0 person(s) were injured. 0 person(s) died.FORD CROWN VICTORIA 1993 problem was reported in HUDSON, ME. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #969414

FORD CROWN VICTORIA 1993 car safety problem was reported on May 18, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:PADS . ABS, BRAKE FAILURE , REPLACEMENT OF DISC ROTORS AND PADS, CALIPERS IN FRONT AND REAR. TT.0 person(s) were injured. 0 person(s) died.FORD CROWN VICTORIA 1993 problem was reported in HUDSON, ME. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #969414

FORD CROWN VICTORIA 1993 car safety problem was reported on May 18, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:ANTILOCK . ABS, BRAKE FAILURE , REPLACEMENT OF DISC ROTORS AND PADS, CALIPERS IN FRONT AND REAR. TT.0 person(s) were injured. 0 person(s) died.FORD CROWN VICTORIA 1993 problem was reported in HUDSON, ME. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #969781

FORD CROWN VICTORIA 1993 car safety problem was reported on July 21, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE:DELIVERY . STARTED VEHICLE AND NOTICE A STRONG GASOLINE SMELL THE GAS LINE HAD SEPARATED AND VEHICLE SAT IN A POOL OF FUEL. TT.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACT74W5TX. FORD CROWN VICTORIA 1993 problem was reported in IRVING, TX. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #969926

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:IGNITION . WHILE DRIVING RAINY WEATHER, LOST ALL VEHICLE POWER; BRAKE PEDAL WENT TO FLOOR; VEHICLE JERKED; NO EMERGENCY BRAKE, SHIFTED GEARS, NO RESPONSE. TT.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W4PX. FORD CROWN VICTORIA 1993 problem was reported in BENNETT, 00. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #969926

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS . WHILE DRIVING RAINY WEATHER, LOST ALL VEHICLE POWER; BRAKE PEDAL WENT TO FLOOR; VEHICLE JERKED; NO EMERGENCY BRAKE, SHIFTED GEARS, NO RESPONSE. TT.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W4PX. FORD CROWN VICTORIA 1993 problem was reported in BENNETT, 00. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #969926

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with PARKING BRAKE:CONVENTIONAL . WHILE DRIVING RAINY WEATHER, LOST ALL VEHICLE POWER; BRAKE PEDAL WENT TO FLOOR; VEHICLE JERKED; NO EMERGENCY BRAKE, SHIFTED GEARS, NO RESPONSE. TT.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W4PX. FORD CROWN VICTORIA 1993 problem was reported in BENNETT, 00. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #969926

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . WHILE DRIVING RAINY WEATHER, LOST ALL VEHICLE POWER; BRAKE PEDAL WENT TO FLOOR; VEHICLE JERKED; NO EMERGENCY BRAKE, SHIFTED GEARS, NO RESPONSE. TT.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W4PX. FORD CROWN VICTORIA 1993 problem was reported in BENNETT, 00. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #970920

FORD CROWN VICTORIA 1993 car safety problem was reported on Aug 22, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:IGNITION . DISCOVERD DETACHED WIRING THAT CAME FROM UNDER THE DASH AND VEHICLE WOULD NO LONGER START. TT.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP73W3PX. FORD CROWN VICTORIA 1993 problem was reported in THEODORE, AL. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #971626

FORD CROWN VICTORIA 1993 car safety problem was reported on Sept 06, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:WIRING:FRONT UNDERHOOD . ENGINE COMPARTMENT FIRE, SPREAD TO THE PASSENGER COMPARTMENT, MASTER CYLINDER PROBABLY CAUSED FIRE, EXPERIENCED BRAKE FAILURE BEFORE FIRE. TT.Vehicle was on fire. 0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W8PX. FORD CROWN VICTORIA 1993 problem was reported in CRARYVILLE, NY. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #971626

FORD CROWN VICTORIA 1993 car safety problem was reported on Sept 06, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:MASTER CYLINDER . ENGINE COMPARTMENT FIRE, SPREAD TO THE PASSENGER COMPARTMENT, MASTER CYLINDER PROBABLY CAUSED FIRE, EXPERIENCED BRAKE FAILURE BEFORE FIRE. TT.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W8PX. FORD CROWN VICTORIA 1993 problem was reported in CRARYVILLE, NY. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #485101

FORD CROWN VICTORIA 1993 car safety problem was reported on June 05, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING:HYDRAULIC POWER ASSIST SYSTEM . STEERING SYSTEM FAILURE KNOWN AS 'STEERING BIND,' CAUSED LOSS OF CONTROL/ACCIDENT. *AK.Vehicle was involved in a crash. Vehicle was on fire. 1 person(s) were injured. 0 person(s) died.FORD CROWN VICTORIA 1993 problem was reported in NORFOLK, VA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #474770

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 24, 1994.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING:WHEEL AND HANDLE BAR . VEHICLE EXPERIENCED INTERMITTENT BINDING IN STEERING PERFORMANCE WHILE MAKING WIDE LEFT TURNS/U-TURNS DUE TO A DESIGN DEFECT IN STEERING COLUMN BEARINGS. *A.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP71W3PX. FORD CROWN VICTORIA 1993 problem was reported in WARRENTON, MO. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #474770

FORD CROWN VICTORIA 1993 car safety problem was reported on Aug 11, 1994.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING:GEAR BOX (OTHER THAN RACK AND PINION) . REPLACED STEERING GEAR BOX..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP71W3PX. FORD CROWN VICTORIA 1993 problem was reported in WARRENTON, MO. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #472403

FORD CROWN VICTORIA 1993 car safety problem was reported on May 31, 1994.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT:CONTROL ARM . UPPER CONTROL ARM REQUIRED REPAIR, TO INCLUDE THE WELDING OF THE BRACKET WITH A REINFORCEMENT PLATE. *TW.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP71WXPX. FORD CROWN VICTORIA 1993 problem was reported in TIFFIN, OH. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #974659

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:ANTILOCK . IN WET OR DRY WEATHER THE ABS LOCKED UP . TT PROBLEMS WITH THE ABS SYSTEM STRTED AT THE TIME OF PURCHASE, CONSUMER HAD THE VEHICLE SERVICED NUMEROUS TIMES, AND MOST OF THE COMPONETS WERE REPLACED, INCLUDING THE DISC PADS BRAKE LINES AND COMPUTER, IT SEEMED THAT THE PROBLEM WAS RESOLVED BUT HAS REOCCURED INTERMITTENLY SINCE THEN,THE BRAKES LOCK WHEN COMSING TO A STOP CAUSING THE VEHICLE TO SKID, WHEN RESUMING TRAVEL THE BRAKES DO NOT ALWAYS RELEASE, THE BRAKES OCCASSIONALLY ENGAGE WHILE DRIVING.*JB.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP74W4WX. FORD CROWN VICTORIA 1993 problem was reported in CLARK, NJ. Original Owner. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #974659

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS . IN WET OR DRY WEATHER THE ABS LOCKED UP . TT PROBLEMS WITH THE ABS SYSTEM STRTED AT THE TIME OF PURCHASE, CONSUMER HAD THE VEHICLE SERVICED NUMEROUS TIMES, AND MOST OF THE COMPONETS WERE REPLACED, INCLUDING THE DISC PADS BRAKE LINES AND COMPUTER, IT SEEMED THAT THE PROBLEM WAS RESOLVED BUT HAS REOCCURED INTERMITTENLY SINCE THEN,THE BRAKES LOCK WHEN COMSING TO A STOP CAUSING THE VEHICLE TO SKID, WHEN RESUMING TRAVEL THE BRAKES DO NOT ALWAYS RELEASE, THE BRAKES OCCASSIONALLY ENGAGE WHILE DRIVING.*JB.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP74W4WX. FORD CROWN VICTORIA 1993 problem was reported in CLARK, NJ. Original Owner. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #975104

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:CALIPER . BRAKE PINS CONTINUOUSLY CORRODE AND BIND. TT.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP74WAPX. FORD CROWN VICTORIA 1993 problem was reported in PORTSMOUTH, RI. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #975108

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING . STEERING LOCKS UP TEMPORARILY WHEN TURNING, HAD FIXED SEVEN TIMES. TT.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP74WAPX. FORD CROWN VICTORIA 1993 problem was reported in PORTSMOUTH, RI. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #975251

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . VEHICLES HAS ERRATIC ACCELERATION AND DECELERATION WHILE DRIVING. TT.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP73W0PX. FORD CROWN VICTORIA 1993 problem was reported in MANALATAN, NJ. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #975251

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . VEHICLES HAS ERRATIC ACCELERATION AND DECELERATION WHILE DRIVING. TT.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP73W0PX. FORD CROWN VICTORIA 1993 problem was reported in MANALATAN, NJ. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #975258

FORD CROWN VICTORIA 1993 car safety problem was reported on Nov 21, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . AUTOMATIC TRANSMISSION FAILURE, ERRATIC OPERATION OF THE AUTO TRANSMISSION. TT *JB.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):12FALP73W0P. FORD CROWN VICTORIA 1993 problem was reported in MANALATANA, NJ. Vehicle was purchased on 19940601. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #484805

FORD CROWN VICTORIA 1993 car safety problem was reported on July 01, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . VEHICLE SHUDDERS DUE TO A TRANSMISSION PROBLEM. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74WXPX. FORD CROWN VICTORIA 1993 problem was reported in MIAMI, FL. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #488979

FORD CROWN VICTORIA 1993 car safety problem was reported on Aug 29, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:MASTER CYLINDER . MASTER CYLINDER INSTALLED, THE NEXT DAY AFTER APPROXIMATELY 30 MILES OF DRIVING THE BRAKES FAILED/SMOKE AND FIRE WAS OBSERVED AFTER GETTING OUT OF THE CAR. *SD REFERENCED IN EA02-025.Vehicle was on fire. 0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W8PX. FORD CROWN VICTORIA 1993 problem was reported in CRARYVILLE, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #980403

FORD CROWN VICTORIA 1993 car safety problem was reported on Mar 06, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING:HYDRAULIC POWER ASSIST SYSTEM . UPON DECELERATION THE POWER STEERING BECOMES INACTIVE DURING TURNING MANEUVERS. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W2PX. FORD CROWN VICTORIA 1993 problem was reported in STATEN ISLAN, NY. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #980403

FORD CROWN VICTORIA 1993 car safety problem was reported on Mar 06, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING:HYDRAULIC POWER ASSIST SYSTEM . UPON DECELERATION THE POWER STEERING BECOMES INACTIVE DURING TURNING MANEUVERS. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W2PX. FORD CROWN VICTORIA 1993 problem was reported in STATEN ISLAN, NY. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #981423

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SEATS:FRONT ASSEMBLY:HEAD RESTRAINT . DRIVERS SIDE HEAD REST WILL NOT STAY UP, DOES NOT GIVE SUPPORT. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP74W6PX. FORD CROWN VICTORIA 1993 problem was reported in CALABASH, NC. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #502263

FORD CROWN VICTORIA 1993 car safety problem was reported on Apr 01, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . TRANSMISSION FAILED. *SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP73W6PX. FORD CROWN VICTORIA 1993 problem was reported in PITMAN, NJ. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #502263

FORD CROWN VICTORIA 1993 car safety problem was reported on Apr 01, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:STARTER ASSEMBLY . STARTER FAILED. *SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP73W6PX. FORD CROWN VICTORIA 1993 problem was reported in PITMAN, NJ. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #983434

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with COMMUNICATIONS:HORN ASSEMBLY . HORN IS LOCATED IN A BAD SPOT, WHEN STEERING WHEEL TURNS CANT FIND HORN. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP73W1PX. FORD CROWN VICTORIA 1993 problem was reported in WESTFIELD, MA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #503447

FORD CROWN VICTORIA 1993 car safety problem was reported on Mar 13, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:ANTILOCK . ANTILOCK BRAKING SYSTEM FAILED. *SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP71W1PX. FORD CROWN VICTORIA 1993 problem was reported in LOS ANGELE, CA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #503447

FORD CROWN VICTORIA 1993 car safety problem was reported on Nov 16, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . WHEEL SENSOR REPLACED. *SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP71W1PX. FORD CROWN VICTORIA 1993 problem was reported in LOS ANGELE, CA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #488648

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 01, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . TRANSMISSION LEAKS. *SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in GLADSTONE, MO. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #488648

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 01, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:DRIVELINE:UNIVERSAL JOINT . UNIVERSAL JOINT REPLACED. *SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in GLADSTONE, MO. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #503448

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 11, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . TRANSMISSION FAILS IN HILLY AREA. *SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP71WXPX. FORD CROWN VICTORIA 1993 problem was reported in LOS ANGELE, CA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #488648

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 01, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . THROTTLE SENSOR REPLACED. *SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in GLADSTONE, MO. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #488648

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 01, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . THROTTLE VALVE REPLACED. *SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in GLADSTONE, MO. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #488648

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 01, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . ROUGH IDLE/VIBRATION. *SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in GLADSTONE, MO. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #503449

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 17, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . TRANSMISSION DRIVE TRAIN EXPLODED. *SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP71W1PX. FORD CROWN VICTORIA 1993 problem was reported in LOS ANGELE, CA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #503450

FORD CROWN VICTORIA 1993 car safety problem was reported on July 01, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES . TRANSMISSION COOLING LINE LEAKS. *SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP71W6PX. FORD CROWN VICTORIA 1993 problem was reported in LOS ANGELE, CA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #487260

FORD CROWN VICTORIA 1993 car safety problem was reported on July 12, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . HIGH IDLE PROBLEM. (LOS ANGELES FIRE DEPT) *SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP71W6PX. FORD CROWN VICTORIA 1993 problem was reported in LOS ANGELE, CA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #487260

FORD CROWN VICTORIA 1993 car safety problem was reported on July 12, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL:ACCELERATOR PEDAL . EXCESSIVE PLAY IN ACCELERATOR PEDAL. *SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP71W6PX. FORD CROWN VICTORIA 1993 problem was reported in LOS ANGELE, CA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #487260

FORD CROWN VICTORIA 1993 car safety problem was reported on July 12, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES . TRANSMISSION COOLING LINES REPAIRED. (LOS ANGELES FIRE DEPT) *SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP71W6PX. FORD CROWN VICTORIA 1993 problem was reported in LOS ANGELE, CA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #487260

FORD CROWN VICTORIA 1993 car safety problem was reported on July 12, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:WINDSHIELD WIPER/WASHER . WINDSHIELD WIPER BLADE REPLACED DUE TO POOR VISIBILITY. (LOS ANGELES FIRE DEPT)*SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP71W6PX. FORD CROWN VICTORIA 1993 problem was reported in LOS ANGELE, CA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #473526

FORD CROWN VICTORIA 1993 car safety problem was reported on May 01, 1994.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING:WHEEL AND HANDLE BAR . STEERING PROBLEMS, CAUSING STEERING TO WANDER. *SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP74W2PX. FORD CROWN VICTORIA 1993 problem was reported in MILNER, GA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #985946

FORD CROWN VICTORIA 1993 car safety problem was reported on June 20, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING:LINKAGES . POLICE VEHICLE. WHEN TURNING THE WHEEL IT STICKS AND HAS TO BE FORCED OUT OF THAT POSITION.PLEASE DESCRIBE..Vehicle Identification Number (VIN):2FACP71W1PX. FORD CROWN VICTORIA 1993 problem was reported in SANDWICH, IL. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #503219

FORD CROWN VICTORIA 1993 car safety problem was reported on Mar 28, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:ROTOR . BRAKE ROTORS WARPED, CAUSING VIBRATION WHEN BRAKES APPLIED.*SD.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP74W5PX. FORD CROWN VICTORIA 1993 problem was reported in NORTON, OH. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #458144

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 25, 1992.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING . STEERING PROBLEM CAUSES VEHICLE TO DRIFT TO LEFT AND RIGHT, CAUSING DIFFICULTY CONTROLLING VEHICLE. *DH.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W3PX. FORD CROWN VICTORIA 1993 problem was reported in EDGEWATER, FL. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #986946

FORD CROWN VICTORIA 1993 car safety problem was reported on June 24, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT . WHILE TRAVELING ON HIGHWAY AT SPEED OF 60 MPH, RING & PINION GEAR FAILED, VEHICLE LOST CONTROL, TURNING SIDEWAYS. OTHER VEHICLES AVOIDED IMPACT. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W1PX. FORD CROWN VICTORIA 1993 problem was reported in RESTON, VA. Original Owner. Vehicle was purchased on 19931201. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 60 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #801861

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . THE TRANSMISSION STICKS WHEN SHIFTING GEAR . PLEASE DESCRIBE .*AK.FORD CROWN VICTORIA 1993 problem was reported in NEW BOSTON, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #507637

FORD CROWN VICTORIA 1993 car safety problem was reported on Aug 13, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . TRANSMISSION SHUDDERS WHEN OVERDRIVE ENGAGES..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP74W8PX. FORD CROWN VICTORIA 1993 problem was reported in NOVI, MI. Vehicle was purchased on 19950717. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #510730

FORD CROWN VICTORIA 1993 car safety problem was reported on Sept 01, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER . TORQUE CONVERTER FAILURE..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP74W8PX. FORD CROWN VICTORIA 1993 problem was reported in OAK LAWN, IL. Vehicle was purchased on 19940301. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 50 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #506216

FORD CROWN VICTORIA 1993 car safety problem was reported on July 02, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with LATCHES/LOCKS/LINKAGES:DOORS:LATCH . DRIVERS SIDE REAR DOOR CAN'T BE OPENED DUE TO CHILD SAFETY LATCH FAILURE..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in RACELAND, LA. Vehicle was purchased on 19940201. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #506216

FORD CROWN VICTORIA 1993 car safety problem was reported on Feb 01, 1994.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE:GASOLINE . ENGINE MAKES NOISE LIKE METAL RUBBING METAL..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in RACELAND, LA. Vehicle was purchased on 19940201. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #511211

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 20, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . SUDDEN ACCELERATION DUE TO THROTTLE VALVE FAILURE..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in NORWICH, CT. Original Owner. Vehicle was purchased on 19931101. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 60 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #601992

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 23, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . TRANSMISSION BUCKED PRIOR TO RECALL, RECALL REPAIRS UNSATISFACTORY..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74WXPX. FORD CROWN VICTORIA 1993 problem was reported in WHITE PLAINS, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #513748

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:MANUAL TRANSMISSION . TRANSMISSION WAS LEAKING AND LOOSING PRESSURE, INHIBITING ABILITY TO ACCELERATE WHEN ENTERING TRAFFIC..Vehicle Identification Number (VIN):2FALP74W4PX. FORD CROWN VICTORIA 1993 problem was reported in NORTH MIAM, FL. Vehicle was purchased on 19940427. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #513633

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS . REAR FUEL LINE SEGMENT WORN OUT BY AREAS CAUSED BY THE POINT OF CONTACTS WITH OTHER PARTS. *AK.Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in SAN JUAN, PR. Vehicle was purchased on 19960226. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #544836

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 07, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER . TORQUE CONVERTER FAILED..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP71W7FX. FORD CROWN VICTORIA 1993 problem was reported in LOS ANGELES, CA. Original Owner. Vehicle was purchased on 19930801. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #513964

FORD CROWN VICTORIA 1993 car safety problem was reported on Sept 29, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER . TORQUE CONVERTER NOISE WHEN UPSHIFTING 2 TIMES..0 person(s) died.Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in JEFFERSON VALLEY, NY. Original Owner. Vehicle was purchased on 19920901. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #513960

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 07, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . TRANSMISSION SLIPS WHILE SHIFTING..0 person(s) died.Vehicle Identification Number (VIN):2FALP71W7FX. FORD CROWN VICTORIA 1993 problem was reported in LOS ANGELES, CA. Original Owner. Vehicle was purchased on 19930801. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #810078

FORD CROWN VICTORIA 1993 car safety problem was reported on Mar 03, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING:LINKAGES:TIE ROD ASSEMBLY . WHILE PARKING VEHICLE OUTER ROD FAILED, RENDERING VEHICLE UNDRIVABLE. *AK.Vehicle Identification Number (VIN):2FACP71W1PX. FORD CROWN VICTORIA 1993 problem was reported in EAST HARDWICK, VT. Vehicle was purchased on 19961001. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: DIESEL. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #807875

FORD CROWN VICTORIA 1993 car safety problem was reported on Dec 19, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE:DELIVERY . THE FUEL CONNECTION TO THE GAS TANK AND FUEL PUMP CORRODED, MADE SMALL HOLES AND SPRAYED GASOLINE UNDER THE VEHICLE. PROBLEM CORRECTED BY FORD DEALER. *AK.Vehicle Identification Number (VIN):2FACP74W3PX. FORD CROWN VICTORIA 1993 problem was reported in BANGOR, ME. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #812550

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:POWER WINDOW DEVICES AND CONTROLS . FRONT DRIVER'S SIDE AND REAR RIGHT SIDE POWER WINDOWS DONT SLIDE DOWN OR UP. *AK.FORD CROWN VICTORIA 1993 problem was reported in TALLAHASSEE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #517458

FORD CROWN VICTORIA 1993 car safety problem was reported on May 10, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with LATCHES/LOCKS/LINKAGES:HOOD:LATCH . THE HOOD OPENED, OBSCURING VISION..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP71W9PX. FORD CROWN VICTORIA 1993 problem was reported in COTTAGE GROVE, MN. Vehicle was purchased on 19960901. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 55 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #814104

FORD CROWN VICTORIA 1993 car safety problem was reported on July 01, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT:CONTROL ARM:UPPER ARM . CONSUMER STATES THAT THERE WAS A RECALL ON HIS VEHICLE . HE TOOK VEHICLE TO DEALER FOR REPAIR . AFTER REPAIR OF VEHICLE BY DEALER THE CONDITION OF THE VEHICLE BECAME WORSE. 95V-194000. *AK AFTER REPAIR THE HOOD HAVE TO BE SLAMMED DOWN FROM FULL UP POSITION TO GET IT LATCHED. *YH .Vehicle Identification Number (VIN):2FACP71W6PX. FORD CROWN VICTORIA 1993 problem was reported in ANITA, IA. Vehicle was purchased on 19951201. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #814104

FORD CROWN VICTORIA 1993 car safety problem was reported on July 01, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with LATCHES/LOCKS/LINKAGES:HOOD:LATCH . CONSUMER STATES THAT THERE WAS A RECALL ON HIS VEHICLE . HE TOOK VEHICLE TO DEALER FOR REPAIR . AFTER REPAIR OF VEHICLE BY DEALER THE CONDITION OF THE VEHICLE BECAME WORSE. 95V-194000. *AK AFTER REPAIR THE HOOD HAVE TO BE SLAMMED DOWN FROM FULL UP POSITION TO GET IT LATCHED. *YH .Vehicle Identification Number (VIN):2FACP71W6PX. FORD CROWN VICTORIA 1993 problem was reported in ANITA, IA. Vehicle was purchased on 19951201. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #517457

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER . THE TORQUE CONVERTER FAILED..0 person(s) died.FORD CROWN VICTORIA 1993 problem was reported in ST. SIMONS, GA. Original Owner. Vehicle was purchased on 19930301. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:FWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #519504

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER . TORQUE CONVERTOR FAILED, CAUSING LOSS OF CONTROL..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in BOURNE, MA. Original Owner. Vehicle was purchased on 19931201. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 35 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #519203

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:POWER ASSIST:VACUUM . POWER BOOSTER FAILED, CAUSING BRAKES TO FADE..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP73W2PX. FORD CROWN VICTORIA 1993 problem was reported in DECATUR, GA. Original Owner. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #520736

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER . AUTOMATIC TRANSMISSION CONVERTER FAILS FREQUENTLY..Vehicle Identification Number (VIN):2FACO74W3OX. FORD CROWN VICTORIA 1993 problem was reported in METAIRIE, LA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #518837

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 01, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with EXTERIOR LIGHTING:TURN SIGNAL:SWITCH . WHEN THE HEADLAMPS ARE DIMMED FOR ONCOMING TRAFFIC THE WINDSHIELD WIPERS MALFUNCTION, CAUSING POOR VISIBILITY IN RAIN. *AK.FORD CROWN VICTORIA 1993 problem was reported in LEESVILLE, SC. Vehicle was purchased on 19960525. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 55 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #522649

FORD CROWN VICTORIA 1993 car safety problem was reported on Aug 14, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER . THE TRANSMISSION/TORQUE CONVERTER HAS FAILED FOR THE SECOND TIME..FORD CROWN VICTORIA 1993 problem was reported in BURLINGTON, MA. Vehicle was purchased on 19971010. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #521352

FORD CROWN VICTORIA 1993 car safety problem was reported on Apr 01, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE:GASOLINE . WHILE DRIVING VEHICLE LOST POWER/STALLED. ALSO, TRANSMISSION FAILURE. *AK.FORD CROWN VICTORIA 1993 problem was reported in HUNTINGTOWN, MD. Original Owner. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #521352

FORD CROWN VICTORIA 1993 car safety problem was reported on Apr 01, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . WHILE DRIVING VEHICLE LOST POWER/STALLED. ALSO, TRANSMISSION FAILURE. *AK.FORD CROWN VICTORIA 1993 problem was reported in HUNTINGTOWN, MD. Original Owner. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #520736

FORD CROWN VICTORIA 1993 car safety problem was reported on May 13, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER . TORQUE CONVERTER FAILED..0 person(s) died.Vehicle Identification Number (VIN):2FACP74W3PX. FORD CROWN VICTORIA 1993 problem was reported in METAIRIE, LA. Original Owner. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #819236

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . CRUISE CONTROL WAS SET FOR 60 MPH ,WENT TO DISENGAGE,STARTED TO ACCELERATE DID NOT DISENGAGE, TOOK ABOUT 4 MINUTES IN ORDER TO SLOW DOWN OR GAIN CONTROL. THIS DEFECT CAN RESULT IN AN ACCIDENT. *AK.Vehicle Identification Number (VIN):2SALP74W4PX. FORD CROWN VICTORIA 1993 problem was reported in UNION, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #819553

FORD CROWN VICTORIA 1993 car safety problem was reported on Nov 26, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER . TRANSMISSION/TORQUE CONVERTER NEEDS TO BE REPLACED. CONSUMER ALSO HAS REPLACED THE TORQUE CONVERTER IN JAN OF 96. THE DEALER HAS BEEN NOTIFIED..Vehicle Identification Number (VIN):ASA1P74W3PX. FORD CROWN VICTORIA 1993 problem was reported in VIRGINIA BEACH, VA. Original Owner. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #523771

FORD CROWN VICTORIA 1993 car safety problem was reported on Apr 04, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:STARTER ASSEMBLY . IGNITION FAILED..0 person(s) died.Vehicle Identification Number (VIN):2FALP74W1PX. FORD CROWN VICTORIA 1993 problem was reported in SPRING HILL, FL. Original Owner. Vehicle was purchased on 19930503. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 70 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #524909

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE:GASOLINE . VEHICLE STALLS OCCASIONALLY WHEN IDLING OR GOING AROUND CORNERS..0 person(s) died.Vehicle Identification Number (VIN):2FACP74W5PX. FORD CROWN VICTORIA 1993 problem was reported in MARLBOROUGH, MA. Original Owner. Vehicle was purchased on 19930301. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #529777

FORD CROWN VICTORIA 1993 car safety problem was reported on Feb 23, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . DEPUTY PLACED VEHICLE IN PARK AND EXITED VEHICLE. TEN MINUTES LATER THE DEPUTY HEARD A CRASH AND OBSERVED THAT THE VEHICLE HAD CRASHED THROUGH THE GARAGE DOOR..Vehicle Identification Number (VIN):2FACP71W4PX. FORD CROWN VICTORIA 1993 problem was reported in DAYTON, OH. Original Owner. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #529778

FORD CROWN VICTORIA 1993 car safety problem was reported on Feb 23, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . DEPUTY PLACED VEHICLE IN PARK AND EXITED VEHICLE. TEN MINUTES LATER THE DEPUTY HEARD A CRASH AND OBSERVED THAT THE VEHICLE HAD CRASHED THROUGH THE GARAGE DOOR..Vehicle Identification Number (VIN):2FACP71W4PX. FORD CROWN VICTORIA 1993 problem was reported in DAYTON, OH. Original Owner. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #529775

FORD CROWN VICTORIA 1993 car safety problem was reported on Feb 23, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . DEPUTY PLACED VEHICLE IN PARK AND EXITED VEHICLE. TEN MINUTES LATER THE DEPUTY HEARD A CRASH AND OBSERVED THAT THE VEHICLE HAD CRASHED THROUGH THE GARAGE DOOR..Vehicle Identification Number (VIN):2FACP71W4PX. FORD CROWN VICTORIA 1993 problem was reported in DAYTON, OH. Original Owner. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #820331

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 06, 1998.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with AIR BAGS:FRONTAL . INVOLVED IN A FRONTAL COLLISION AT 15-20 MPH AND THE AIR BAGS DID NOT DEPLOY FULLY, CAUSING THE DRIVER'S ELBOW TO BREAK ON THE WINDSHIELD. *AK.Vehicle was involved in a crash. 1 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W1PX. FORD CROWN VICTORIA 1993 problem was reported in WELLINGTON, FL. Accident was reported to Police. Original Owner. Vehicle was purchased on 19931030. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 20 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #820331

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 06, 1998.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with AIR BAGS:FRONTAL . INVOLVED IN A FRONTAL COLLISION AT 15-20 MPH AND THE AIR BAGS DID NOT DEPLOY FULLY, CAUSING THE DRIVER'S ELBOW TO BREAK ON THE WINDSHIELD. *AK.Vehicle was involved in a crash. 1 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W1PX. FORD CROWN VICTORIA 1993 problem was reported in WELLINGTON, FL. Accident was reported to Police. Original Owner. Vehicle was purchased on 19931030. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 20 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #821072

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:WINDSHIELD WIPER/WASHER . WINDSHIELD WIPERS WILL BECOME INOPERABLE, CAUSE UNKNOWN. PLEASE GIVE ANY FURTHER DETAILS. *AK.FORD CROWN VICTORIA 1993 problem was reported in BAKAER, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #523403

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:POWER WINDOW DEVICES AND CONTROLS . POWER WINDOW ACTUATOR FAILED TWICE ON DRIVER'S SIDE, ONCE LEFT REAR PASSENGER'S SIDE, AND ONCE RIGHT FRONT PASSENGER'S SIDE. *AK.Vehicle Identification Number (VIN):2FALP73W4PX. FORD CROWN VICTORIA 1993 problem was reported in GRANADA HILLS, CA. Vehicle was purchased on 19950901. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #527038

FORD CROWN VICTORIA 1993 car safety problem was reported on Nov 09, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER . TORQUE CONVERTER FAILED CAUSING VIBRATION ON TWO OCCASIONS..0 person(s) died.Vehicle Identification Number (VIN):2FALP74WXPX. FORD CROWN VICTORIA 1993 problem was reported in LAPEL, IN. Vehicle was purchased on 19941122. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #528035

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:ANTILOCK . ANTI LOCK BRAKE RELAY FAILED..0 person(s) died.Vehicle Identification Number (VIN):2FACP71W1PX. FORD CROWN VICTORIA 1993 problem was reported in CHICO, CA. Vehicle was purchased on 19971118. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #528035

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:MASTER CYLINDER . CLIP BROKE ON THE MASTER CYLINDER RESERVOIR..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP71W1PX. FORD CROWN VICTORIA 1993 problem was reported in CHICO, CA. Vehicle was purchased on 19971118. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #530590

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 04, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . SUDDEN ACCELERATION CAUSED ACCIDENTS..0 person(s) died.Vehicle Identification Number (VIN):2FALP74W4PX. FORD CROWN VICTORIA 1993 problem was reported in UNION, NJ. Original Owner. Vehicle was purchased on 19940601. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #530272

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:WIRING:INTERIOR/UNDER DASH . WIRING HARNESS FAULTY CAUSING ABS LIGHT AND BRAKE LIGHT FAILURES..0 person(s) died.Vehicle Identification Number (VIN):2FACP71W1PX. FORD CROWN VICTORIA 1993 problem was reported in CHICO, CA. Vehicle was purchased on 19971118. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #532685

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR . LOCATION OF STARTER ALLOWS CONNECTING WIRES TO BE EXPOSED TO RAIN, SNOW ETC.,PREVENTNG VEHICLE FROM STARTING..0 person(s) died.Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in CYNTHIANA, KY. Vehicle was purchased on 19951101. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #532685

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE:DELIVERY . FUEL LINE RUSTED THROUGH CAUSING GAS TO LEAK..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in CYNTHIANA, KY. Vehicle was purchased on 19951101. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #534630

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 01, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:GLASS, SIDE/REAR . LEFT/RIGHT WINDOWS REGULATOR INOPERABLE..Vehicle Identification Number (VIN):2FACP74W4PX. FORD CROWN VICTORIA 1993 problem was reported in MCALLEN, TX. Vehicle was purchased on 19930930. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #823253

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 23, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER . TORQUE CONVERTER WENT BAD, CAUSING THE VEHICLE TO ACCELERATE AND DECELERATE ON ITS OWN. THE MANUFACTURER HAS BEEN NOTIFIED. .Vehicle Identification Number (VIN):2FALP74W7PX. FORD CROWN VICTORIA 1993 problem was reported in TAYLORS, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. FUEL SYSTEM:N/A. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #823982

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER . WHEN SHIFTING FROM THIRD TO FOURTH GEAR THE VEHICLE WOULD SHAKE AT ABOUT 40 TO 45MPH. DEALER REPLACED THE TORQUE CONVERTER. *AK .Vehicle Identification Number (VIN):2FALP74W2PX. FORD CROWN VICTORIA 1993 problem was reported in SEVIERVILLE, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 45 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #524557

FORD CROWN VICTORIA 1993 car safety problem was reported on July 14, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION . BEARINGS WITHIN THE FRONT AND REAR AXLES FAILED CAUSING EXTENSIVE DAMAGE TO AXLES..FORD CROWN VICTORIA 1993 problem was reported in SANTA ANA, CA. Original Owner. Vehicle was purchased on 19930917. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #524557

FORD CROWN VICTORIA 1993 car safety problem was reported on July 14, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:REAR . BEARINGS WITHIN THE FRONT AND REAR AXLES FAILED CAUSING EXTENSIVE DAMAGE TO AXLES..FORD CROWN VICTORIA 1993 problem was reported in SANTA ANA, CA. Original Owner. Vehicle was purchased on 19930917. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #825419

FORD CROWN VICTORIA 1993 car safety problem was reported on July 12, 1998.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:ANTILOCK . WHEN THE BRAKES WERE APPLIED DURING A PANIC STOP THE BRAKE PEDAL WENT TO THE FLOOR, RESULTING IN EXTENDED STOPPING DISTANCE, AND BLOWING THE VACUUM ON THE MASTER CYLINDER. VEHICLE IS BEING REPAIRED BY DEALER. *AK.FORD CROWN VICTORIA 1993 problem was reported in MONONGAH, WV. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #825419

FORD CROWN VICTORIA 1993 car safety problem was reported on July 12, 1998.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:MASTER CYLINDER . WHEN THE BRAKES WERE APPLIED DURING A PANIC STOP THE BRAKE PEDAL WENT TO THE FLOOR, RESULTING IN EXTENDED STOPPING DISTANCE, AND BLOWING THE VACUUM ON THE MASTER CYLINDER. VEHICLE IS BEING REPAIRED BY DEALER. *AK.FORD CROWN VICTORIA 1993 problem was reported in MONONGAH, WV. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #538838

FORD CROWN VICTORIA 1993 car safety problem was reported on Nov 03, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER . THIRD TORQUE CONVERTER INSTALLLED, SHOULD LAST A LIFETIME..Vehicle Identification Number (VIN):2FACP74W5PX. FORD CROWN VICTORIA 1993 problem was reported in OLD TAPPAN, NJ. Original Owner. Vehicle was purchased on 19930415. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #539844

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 04, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with EQUIPMENT:MECHANICAL:CARRIER/RACK . BOLT HOLDING DOWN SPARE TIRE IN TRUNK SHEARED OFF DURING CRASH, CAUSING SPARE TIRE TO BE THROWN AGAINST REAR SEAT BACK. LACK OF REINFORCEMENT CAUSED REAR SEAT BACK TO BOW FORWARD SEVERAL INCHES, KILLING THREE CHILDREN. ALL THREE CHILDREN WERE WEARING SEAT BELTS AND DIED OF INTERNAL INJURIES CAUSED BY FORCE OF THE SEAT BACK SQUEEZING AGAINST FIXED SEAT BELTS. *SLC.5 person(s) were injured. 3 person(s) died.Vehicle Identification Number (VIN):2FALP73W1PX. FORD CROWN VICTORIA 1993 problem was reported in JACKSONVILLE, FL. Accident was reported to Police. Original Owner. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #539844

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 04, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SEATS:FRONT ASSEMBLY:RECLINER . BOLT HOLDING DOWN SPARE TIRE IN TRUNK SHEARED OFF DURING CRASH, CAUSING SPARE TIRE TO BE THROWN AGAINST REAR SEAT BACK. LACK OF REINFORCEMENT CAUSED REAR SEAT BACK TO BOW FORWARD SEVERAL INCHES, KILLING THREE CHILDREN. ALL THREE CHILDREN WERE WEARING SEAT BELTS AND DIED OF INTERNAL INJURIES CAUSED BY FORCE OF THE SEAT BACK SQUEEZING AGAINST FIXED SEAT BELTS. *SLC.5 person(s) were injured. 3 person(s) died.Vehicle Identification Number (VIN):2FALP73W1PX. FORD CROWN VICTORIA 1993 problem was reported in JACKSONVILLE, FL. Accident was reported to Police. Original Owner. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #780461

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with OTHER . UNSPECIFIED..FORD CROWN VICTORIA 1993 problem was reported in LAKE CITY, MN. Vehicle was not using Cruise Control. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #828713

FORD CROWN VICTORIA 1993 car safety problem was reported on Aug 01, 1998.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER . WHEN DRIVING BETWEEN 35-40MPH VEHICLE JERKS. DEALER NOT AWARE OF THE PROBLEM. MECHANIC STATES THE TORQUE CONVERTER NEEDS TO BE REPLACED. *AK.Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in WESTLAND, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #829088

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 14, 1998.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING . WHILE THE KEY IS IN THE IGNITION AND THE VEHICLE IN PARK POSTION AND THE EMERGENCY PARKING BRAKE IS ACTIVATED, HEARD A POPPING NOISE. THE VEHICLE ROLLED OVER, CAUSING MAJOR INJURIES AND LOSS OF THE VEHICLE. CAUSE UNKNOWN. PLEASE PROVIDE DETAILS. *AK.Vehicle was involved in a crash. 1 person(s) were injured. FORD CROWN VICTORIA 1993 problem was reported in MACON, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #829257

FORD CROWN VICTORIA 1993 car safety problem was reported on Apr 01, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING . WHEN ATTEMPTING TO TURN THE VEHICLE OFF THE KEY WOULD NOT COME OUT OF THE IGNITION DUE TO THE ACTUATOR WITHIN THE STEERING WHICH WENT BAD. CONSUMER HAS CONTACTED THE DEALER, DEALER HAS REPLACED THE PARTS ON TWO OCCASIONS PARTS NUMBER F2DZ3E723A AND FODZ3E715A. *AK.Vehicle Identification Number (VIN):2FACP74W7PX. FORD CROWN VICTORIA 1993 problem was reported in CINCINNATI, OH. Original Owner. Vehicle was purchased on 19930203. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #700771

FORD CROWN VICTORIA 1993 car safety problem was reported on Nov 10, 1998.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT . NO SUMMARY PROVIDED BY CONSUMER.Vehicle Identification Number (VIN):2FALP73W9PX. FORD CROWN VICTORIA 1993 problem was reported in HUBBARDSTON, MI. Vehicle was purchased on 19970701. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 10 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #832563

FORD CROWN VICTORIA 1993 car safety problem was reported on Feb 01, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER . WHENEVER DRIVING AT VARIOUS SPEED THE TORQUE CONVERTOR WOULD MAKE LOUD NOISES. TOOK TO MECHANIC & INFORMED TORQUE CONVERTOR NEEDED TO BE REPLACED. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP73W2PX. FORD CROWN VICTORIA 1993 problem was reported in VAN BUREN, AR. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #703399

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 27, 1998.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE:DELIVERY . BOTH THE PUMP AND RETURN LINES TO THE GAS TANK FAILED(LEAKING GAS) DUE TO CORROSION. DEALER INFORMED THAT THE CAR COULD NOT BE DRIVEN UNTIL THE LINES WERE REPLACED. DUE TO THE UNIQUE CONFIGURATION OF THE FUEL PUMP ASSEMBLY THE ENTIRE FUEL PUMP AND SENDING UNIT HAD TO BE REPLACED..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP73W9PX. FORD CROWN VICTORIA 1993 problem was reported in QUEENSBURY, NY. Original Owner. Vehicle was purchased on 19930801. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #704857

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 10, 1998.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE:DELIVERY . BOTH THE INTAKE AND RETURN FUEL LINES FAILED(LEAKING GASOLINE) DUE TO CORROSION. DUE TO THE UNIQUE CONFIGURATION THE LEAKING LINES AND BOTH THE FUEL PUMP AND SENDING UNIT NEEDED REPLACING. *AK.Vehicle Identification Number (VIN):2FACP73W9PX. FORD CROWN VICTORIA 1993 problem was reported in QUEENSBURY, NY. Original Owner. Vehicle was purchased on 19930801. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #835503

FORD CROWN VICTORIA 1993 car safety problem was reported on July 01, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT:CONTROL ARM . BALL JOINTS & TIE ROD ENDS WOULD MAKE GROANING NOISES IN THE FRONT END. ITS AN INTERMITTENT PROBLEM. TOOK VEHICLE TO DEALER & NOTHING FOUND. TOOK TO ANOTHER GARAGE & MECHANIC NOTICED TIE ROD END WAS SHOT, AND THAT BALL JOINTS WERE RUSTY & PITTED. THEREFORE, VEHICLE WAS MAKING NOISES WHEN BEING DRIVEN. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP74W1PX. FORD CROWN VICTORIA 1993 problem was reported in WYANDOTTE, MI. Vehicle was purchased on 19960510. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 35 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #835503

FORD CROWN VICTORIA 1993 car safety problem was reported on July 01, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING:LINKAGES:TIE ROD ASSEMBLY . BALL JOINTS & TIE ROD ENDS WOULD MAKE GROANING NOISES IN THE FRONT END. ITS AN INTERMITTENT PROBLEM. TOOK VEHICLE TO DEALER & NOTHING FOUND. TOOK TO ANOTHER GARAGE & MECHANIC NOTICED TIE ROD END WAS SHOT, AND THAT BALL JOINTS WERE RUSTY & PITTED. THEREFORE, VEHICLE WAS MAKING NOISES WHEN BEING DRIVEN. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP74W1PX. FORD CROWN VICTORIA 1993 problem was reported in WYANDOTTE, MI. Vehicle was purchased on 19960510. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 35 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #707093

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 01, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with EXTERIOR LIGHTING:HEADLIGHTS . PLASTIC HEADLAMP LENSES BECOME CLOUDY WITH TIME. THEY PREVENT FULL LAMP OUTPUT TO ROAD. *AK.Vehicle Identification Number (VIN):2FALP73W7PX. FORD CROWN VICTORIA 1993 problem was reported in BROOKLYN, NY. Original Owner. Vehicle was purchased on 19930401. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #838746

FORD CROWN VICTORIA 1993 car safety problem was reported on May 02, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . CRUISE CONTROL SYSTEM DOES NOT ENGAGE. DEALER/MANFACTURER WERE CONTACTED ABOUT THE PROBLEM. PROBLEM HAS NOT BEEN CORECTED. *AK.Vehicle Identification Number (VIN):2FACP74W3PX. FORD CROWN VICTORIA 1993 problem was reported in ROSEVILLE, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #838983

FORD CROWN VICTORIA 1993 car safety problem was reported on June 05, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with AIR BAGS:FRONTAL . AIR BAG LIGHT FOR DRIVER SIDE AND PASSENGER SIDE AIR BAGS E KEPT FLASHING OFF AND ON..Vehicle Identification Number (VIN):2FACT74W3PX. FORD CROWN VICTORIA 1993 problem was reported in CHESTER, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #838983

FORD CROWN VICTORIA 1993 car safety problem was reported on June 05, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with AIR BAGS:FRONTAL . AIR BAG LIGHT FOR DRIVER SIDE AND PASSENGER SIDE AIR BAGS E KEPT FLASHING OFF AND ON..Vehicle Identification Number (VIN):2FACT74W3PX. FORD CROWN VICTORIA 1993 problem was reported in CHESTER, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #838983

FORD CROWN VICTORIA 1993 car safety problem was reported on June 05, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with AIR BAGS:FRONTAL . AIR BAG LIGHT FOR DRIVER SIDE AND PASSENGER SIDE AIR BAGS E KEPT FLASHING OFF AND ON..Vehicle Identification Number (VIN):2FACT74W3PX. FORD CROWN VICTORIA 1993 problem was reported in CHESTER, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #839184

FORD CROWN VICTORIA 1993 car safety problem was reported on Apr 03, 1998.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL:CRUISE CONTROL . VEHICLE WAS INVOLVOED IN A FIRE WHILE PARKED IN CONSUMER DRIVWAY, CAUSE OF FIRE MAY BE DUE TO RECENT MFR. RECALL # 99 S 15 CONCERNING IGNITION SWITCH. MFR. NOTIFIED AND INFORMED CONSUMER VEHICLE WAS NOT UNDER RECALL. ALSO VEHICLE ON HOLD FOR A WEEK FOR INSPECTION IF NEEDED AT COOKS SALVAGE 228/392-2288. REFERENCED IN EA02-025.FORD CROWN VICTORIA 1993 problem was reported in WIGGINS, MS. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #545860

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE . STRESS CRACKS OF THE FLOOR BOARD CAUSED THE BOLT THAT HOLD THE FRONT DRIVER'S SEAT TO BREAK RESULTING IN THE SEAT BECOMING UNSTABLE AND TO LURCH BACKWARDS..FORD CROWN VICTORIA 1993 problem was reported in EASTON, MD. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #839755

FORD CROWN VICTORIA 1993 car safety problem was reported on May 29, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with AIR BAGS:FRONTAL . WHILE SITTING AT STOPLIGHT VEHICLE WAS HIT FROM THE REAR AND PUSHED INTO A BIG 4X4, CAUSING HOOD TO FOLD IN, AND AIR BAGS DID NOT DEPLOY. ALSO DURING THE ACCIDENT BOTH DRIVER'S AND PASSENGER'S SIDE SEATS COLLAPSED, CAUSING SOME INJURIES TO BOTH DRIVER AND PASSENGER. *AK.Vehicle was involved in a crash. 2 person(s) were injured. 0 person(s) died.FORD CROWN VICTORIA 1993 problem was reported in MARYVILLE, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #839755

FORD CROWN VICTORIA 1993 car safety problem was reported on May 29, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SEATS:FRONT ASSEMBLY:RECLINER . WHILE SITTING AT STOPLIGHT VEHICLE WAS HIT FROM THE REAR AND PUSHED INTO A BIG 4X4, CAUSING HOOD TO FOLD IN, AND AIR BAGS DID NOT DEPLOY. ALSO DURING THE ACCIDENT BOTH DRIVER'S AND PASSENGER'S SIDE SEATS COLLAPSED, CAUSING SOME INJURIES TO BOTH DRIVER AND PASSENGER. *AK.Vehicle was involved in a crash. 2 person(s) were injured. 0 person(s) died.FORD CROWN VICTORIA 1993 problem was reported in MARYVILLE, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #839755

FORD CROWN VICTORIA 1993 car safety problem was reported on May 29, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with AIR BAGS:FRONTAL . WHILE SITTING AT STOPLIGHT VEHICLE WAS HIT FROM THE REAR AND PUSHED INTO A BIG 4X4, CAUSING HOOD TO FOLD IN, AND AIR BAGS DID NOT DEPLOY. ALSO DURING THE ACCIDENT BOTH DRIVER'S AND PASSENGER'S SIDE SEATS COLLAPSED, CAUSING SOME INJURIES TO BOTH DRIVER AND PASSENGER. *AK.Vehicle was involved in a crash. 2 person(s) were injured. 0 person(s) died.FORD CROWN VICTORIA 1993 problem was reported in MARYVILLE, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #604329

FORD CROWN VICTORIA 1993 car safety problem was reported on May 01, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS . BRAKE ROTOR DISCOVERED TO HAVE A DEEP GROVE DUE TO SOME DEFECT IN THE BRAKE SYSTEM. MJS.Vehicle Identification Number (VIN):2FALP74W8PX. FORD CROWN VICTORIA 1993 problem was reported in STATEN ISL, NY. Original Owner. Vehicle was purchased on 19930201. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #840731

FORD CROWN VICTORIA 1993 car safety problem was reported on June 17, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . HAD REC'D RECALL NOTICE (399V124000) IN THE MAIL & NOTIFIED DEALER. WAS INFORMED BY MECHANIC THAT NO PARTS WERE AVAILABLE & DO NOT KNOW WHEN THEY WOULD BE. THE MANUFACTURER DO NOT KNOW WHEN THE PARTS WOULD BE AVAILABE. HAD THE CRUISE CONTROL WIRES DISABLED PRIOR TO RECEIVING NOTICE. OWNER IS DISABLED & USES THE CRUISE CONTROL IN ORDER TO DRIVE..Vehicle Identification Number (VIN):2FALP74W0PX. FORD CROWN VICTORIA 1993 problem was reported in CASSELBERRY, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #842392

FORD CROWN VICTORIA 1993 car safety problem was reported on July 14, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC . VEHICLE DOES NOT START UP RIGHT AWAY. TOOK VEHICLE TO DEALER. WAS INFORMED THAT THE IGNITION SWITCH WIRES HAD TO BE REPLACED DUE TO BEING BURNED IN & AROUND THE COLUMN. THE HEATER WIRES HAD BURNED ALSO. THE SEAT ANCHOR BOLTS HAD CAME OUT OF THE FRONT SEAT. PLUGS, WIRES, AND BRAKES HAD TO BE REPLACED. *AK *ML.Vehicle Identification Number (VIN):2FALP74WXPX. FORD CROWN VICTORIA 1993 problem was reported in WOODBURY HEIGHTS, NJ. Original Owner. Vehicle was purchased on 19931001. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #842392

FORD CROWN VICTORIA 1993 car safety problem was reported on July 14, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:DEFROSTER/DEFOGGER SYSTEM . VEHICLE DOES NOT START UP RIGHT AWAY. TOOK VEHICLE TO DEALER. WAS INFORMED THAT THE IGNITION SWITCH WIRES HAD TO BE REPLACED DUE TO BEING BURNED IN & AROUND THE COLUMN. THE HEATER WIRES HAD BURNED ALSO. THE SEAT ANCHOR BOLTS HAD CAME OUT OF THE FRONT SEAT. PLUGS, WIRES, AND BRAKES HAD TO BE REPLACED. *AK *ML.Vehicle Identification Number (VIN):2FALP74WXPX. FORD CROWN VICTORIA 1993 problem was reported in WOODBURY HEIGHTS, NJ. Original Owner. Vehicle was purchased on 19931001. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #842392

FORD CROWN VICTORIA 1993 car safety problem was reported on July 14, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SEATS . VEHICLE DOES NOT START UP RIGHT AWAY. TOOK VEHICLE TO DEALER. WAS INFORMED THAT THE IGNITION SWITCH WIRES HAD TO BE REPLACED DUE TO BEING BURNED IN & AROUND THE COLUMN. THE HEATER WIRES HAD BURNED ALSO. THE SEAT ANCHOR BOLTS HAD CAME OUT OF THE FRONT SEAT. PLUGS, WIRES, AND BRAKES HAD TO BE REPLACED. *AK *ML.Vehicle Identification Number (VIN):2FALP74WXPX. FORD CROWN VICTORIA 1993 problem was reported in WOODBURY HEIGHTS, NJ. Original Owner. Vehicle was purchased on 19931001. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #842392

FORD CROWN VICTORIA 1993 car safety problem was reported on July 14, 1997.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:IGNITION . VEHICLE DOES NOT START UP RIGHT AWAY. TOOK VEHICLE TO DEALER. WAS INFORMED THAT THE IGNITION SWITCH WIRES HAD TO BE REPLACED DUE TO BEING BURNED IN & AROUND THE COLUMN. THE HEATER WIRES HAD BURNED ALSO. THE SEAT ANCHOR BOLTS HAD CAME OUT OF THE FRONT SEAT. PLUGS, WIRES, AND BRAKES HAD TO BE REPLACED. *AK *ML.Vehicle Identification Number (VIN):2FALP74WXPX. FORD CROWN VICTORIA 1993 problem was reported in WOODBURY HEIGHTS, NJ. Original Owner. Vehicle was purchased on 19931001. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #843887

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . CONSUMER RECEIVED MANUFACTURER'S RECALL 99S15, CONCERNING SPEED CONTROL. CONTACTED DEALER, AND WAS INFORMED NO PARTS WERE AVAILABLE. *AK.FORD CROWN VICTORIA 1993 problem was reported in HUNDSON, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #844503

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . RECALL # 99V124000 FORD/SPEED CONTROL SWITCH; DEALER DOES NOT HAVE PARTS TO CORRECT RECALL NOTICE. OWNER HAS WAITED FOR TWO MONTHS. OWNER HAS RECEIVED SECOND NOTICE. FORD RECALL 99S15. *AK.Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in SAN JUAN, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #547223

FORD CROWN VICTORIA 1993 car safety problem was reported on July 02, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . VEHICLE EXPERIENCING SUDDEN ACCELERATION WHICH NEARLY RESULTED IN COLLISION. POSSIBLE SHORT IN ELECTRICAL SYSTEM MAY HAVE CAUSED FAILURE, PRIOR TO RECALL NOTICE (99V-124). *YC.Vehicle Identification Number (VIN):2FALP74W4PX. FORD CROWN VICTORIA 1993 problem was reported in UNION, NJ. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #547905

FORD CROWN VICTORIA 1993 car safety problem was reported on May 01, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . NO PARTS AVAILABLE FOR RECALL REPAIR OF SPEED CONTROL DEACTIVATION SWITCH. NLM (RECALL #99S15).Vehicle Identification Number (VIN):2FALP74WOPX. FORD CROWN VICTORIA 1993 problem was reported in SAN FRANCI, CA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #710815

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT:CONTROL ARM:LOWER ARM . I PURCHASED THIS CAR USED 03/97 87,000 MILES. WHEN YOU WOULD TURN TO THE LEFT SHARP, IT ALWAYS MADE A CLUNK AND THE CAR WOULD SHIFT OVER. THE CLUNK CONTINUED, SO I TOOK IT TO MY LOCAL FORD DEALER, RUDIG-JENSEN IN NEW LISBON, THEY FOUND THAT THE BOLTS THAT ATTACH THE UPPER CONTROL ARMS TO THE FRAME WERE LOOSE. THE LOOSE BOLTS HAD WORN OUT THE BOLTS AND THE UPPER CONTROL ARM. THEY FOUND THAT WHILE REPLACING THE PARTS, THAT THE BOLT HOLES IN THE FRAME MOUNTING BRACKET HAD WORN AND HAD FRACTURED. THEY WERE UNABLE TO REPAIR THE CAR, AND CALLED GARY'S AUTOBODY OF NEW LISBON TO LOOK AT THE FRAME MOUNTING BRACKET . GARY'S HAVE REPAIRED THE BRACKET BY WELDING IT , AS THE FORD DEALER TOLD MYSELF, THAT THEY COULD NOT REPAIR IT. I WOULD HAVE TO BUY A NEW CAR. I CALLED THE FORD MOTOR COMPANY, AND WAS TOLD THAT THE CAR HAD BEEN IN FOR THE RECALL 95V194000 NHTSA AT NORRIS VERNIER FORD IN TOMAH, WI. AND THAT FORD MOTOR COMPANY WOULD NOT PAY FOR THE REPAIRS, BECAUSE THE VEHICLE HAD ALREADY BEEN IN FOR THE RECALL. THE DAMAGE DONE TO MY VEHICLE IS FROM THE LOOSE BOLTS, AND I FEEL THAT FORD'S FAULTY PRODUCT CAUSED THIS, AND THAT THEY SHOULD REPAIR THE DAMAGE, AS IT IS DUE TO THEIR PROBLEM WITH THESE VEHICLES. THE BOLTS CAN LOOSEN EVEN AFTER BEING CHECKED UNDER THE RECALL. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP71W7PX. FORD CROWN VICTORIA 1993 problem was reported in NEW LISBON, WI. Original Owner. Vehicle was purchased on 19970301. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #552243

FORD CROWN VICTORIA 1993 car safety problem was reported on July 07, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . DURING RECALL REPAIR 99V-124 OF THE SPPED CONTROL DEACTIVATION SWITCH CONSUMER FEELS DEALER MADE ADDITIONAL REPAIRS (DRIVE BELT, DIAGNOSTIC TEST, T-CONNECTOR AND HOSE FOR PCV) THAT WERE UNNEEDED. NLM.Vehicle Identification Number (VIN):2FALP74W5PX. FORD CROWN VICTORIA 1993 problem was reported in YUKON, OK. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #712385

FORD CROWN VICTORIA 1993 car safety problem was reported on Sept 14, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:POWER ASSIST . TRANSMISSION AND BRAKE FAILURE/LOCK-UP ON A VEHICLE THAT HAS BEEN "BABYED" AND METICULOUSLY MAINTAINED IS OUTRAGEOUS. I CANNOT GET FORD MOTOR CO. TO RETURN MY CALLS. I CAN ONLY IMAGINR WHAT KIND OF HORRIFIC ACCIDENT WOULD HAVE OCCURRED IF WE HAD BEEN DRIVING AT HIGHWAY SPEEDS. DEALER'S SHOP ALSO HAD A 95, 97, & 98 CROWN VICS. W/ TRANSMISSION FAILURE. I SUSPECT FORD IS TRYING TO COVER UP A DEFECT..Vehicle Identification Number (VIN):2FALP74WOPX. FORD CROWN VICTORIA 1993 problem was reported in EMERSON, NJ. Original Owner. Vehicle was purchased on 19920901. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #712385

FORD CROWN VICTORIA 1993 car safety problem was reported on Sept 14, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . TRANSMISSION AND BRAKE FAILURE/LOCK-UP ON A VEHICLE THAT HAS BEEN "BABYED" AND METICULOUSLY MAINTAINED IS OUTRAGEOUS. I CANNOT GET FORD MOTOR CO. TO RETURN MY CALLS. I CAN ONLY IMAGINR WHAT KIND OF HORRIFIC ACCIDENT WOULD HAVE OCCURRED IF WE HAD BEEN DRIVING AT HIGHWAY SPEEDS. DEALER'S SHOP ALSO HAD A 95, 97, & 98 CROWN VICS. W/ TRANSMISSION FAILURE. I SUSPECT FORD IS TRYING TO COVER UP A DEFECT..Vehicle Identification Number (VIN):2FALP74WOPX. FORD CROWN VICTORIA 1993 problem was reported in EMERSON, NJ. Original Owner. Vehicle was purchased on 19920901. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #713546

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 14, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING:LINKAGES:TIE ROD ASSEMBLY . LEFT TIE ROD END FELL APART, SOCKET FROM BALL. EXTREME WEAR FROM LACK OF LUBRICATION. NO LUBE FITTING ENGINEERED INTO PART. TOTAL LOSS OF CAR CONTROL. HOW MANY CARS ARE OUT THERE WITH THIS PROBLEM UNDISCOVERED? DEALER FAILED TO COMPENSATE FOR COST OR REPLACEMENT FOR THIS MIS-ENGINEERED OR MIS-MANUFACTURED PART..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W2PX. FORD CROWN VICTORIA 1993 problem was reported in BATAVIA, IL. Original Owner. Vehicle was purchased on 19930901. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 1 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #713645

FORD CROWN VICTORIA 1993 car safety problem was reported on Aug 01, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . TRANSMISSION SHUTTERS GOING INTO OVERDRIVE. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP74W0PX. FORD CROWN VICTORIA 1993 problem was reported in DEARBORN, MI. Vehicle was purchased on 19980401. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 60 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #852081

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 26, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING:WHEEL AND HANDLE BAR . PIN WHITIN THE STEERING COLUMN BROKE. WHEN PUTTING THE KEY INTO IGNITION, THE IGNITION KEPT GOING AROUND, AND THE CONSUMER WAS ABLE TO TAKE THE KEY OUT OF THE IGNITION. BUT, ENGINE KEPT RUNNING..Vehicle Identification Number (VIN):2SACP74W2PX. FORD CROWN VICTORIA 1993 problem was reported in HATBORO, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #852081

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 26, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:IGNITION:SWITCH . PIN WHITIN THE STEERING COLUMN BROKE. WHEN PUTTING THE KEY INTO IGNITION, THE IGNITION KEPT GOING AROUND, AND THE CONSUMER WAS ABLE TO TAKE THE KEY OUT OF THE IGNITION. BUT, ENGINE KEPT RUNNING..Vehicle Identification Number (VIN):2SACP74W2PX. FORD CROWN VICTORIA 1993 problem was reported in HATBORO, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #548918

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:POWER WINDOW DEVICES AND CONTROLS . POWER WINDOW REGULATORS FAILED. MJS.Vehicle Identification Number (VIN):2FALP74W5PX. FORD CROWN VICTORIA 1993 problem was reported in BOYNTON BE, FL. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #549407

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SEATS . BOLTS PULL OUT OF THE FRONT PASSENGER SEAT. MJS.Vehicle Identification Number (VIN):2FALP74WXPX. FORD CROWN VICTORIA 1993 problem was reported in WOODBURY H, NJ. Vehicle was not using Cruise Control. FORD CROWN VICTORIA 1993 drive type:RWD. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #549407

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SEATS . BOLTS PULL OUT OF THE FRONT PASSENGER SEAT. MJS.Vehicle Identification Number (VIN):2FALP74WXPX. FORD CROWN VICTORIA 1993 problem was reported in WOODBURY H, NJ. Vehicle was not using Cruise Control. FORD CROWN VICTORIA 1993 drive type:RWD. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #549407

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . STEERING COLUMN CAUGHT FIRE DUE TO POSSIBLE RECALL COMPONENT FAILURE (99V-124), HOWEVER DENIED BY DEALERSHIP. MJS.Vehicle was on fire. Vehicle Identification Number (VIN):2FALP74WXPX. FORD CROWN VICTORIA 1993 problem was reported in WOODBURY H, NJ. Vehicle was not using Cruise Control. FORD CROWN VICTORIA 1993 drive type:RWD. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #549407

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SEATS . BOLTS PULL OUT OF THE FRONT PASSENGER SEAT. MJS.Vehicle Identification Number (VIN):2FALP74WXPX. FORD CROWN VICTORIA 1993 problem was reported in WOODBURY H, NJ. Vehicle was not using Cruise Control. FORD CROWN VICTORIA 1993 drive type:RWD. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #549407

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING:WHEEL AND HANDLE BAR . STEERING COLUMN CAUGHT FIRE DUE TO POSSIBLE RECALL COMPONENT FAILURE (99V-124), HOWEVER DENIED BY DEALERSHIP. MJS.Vehicle was on fire. Vehicle Identification Number (VIN):2FALP74WXPX. FORD CROWN VICTORIA 1993 problem was reported in WOODBURY H, NJ. Vehicle was not using Cruise Control. FORD CROWN VICTORIA 1993 drive type:RWD. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #549407

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING:WHEEL AND HANDLE BAR . STEERING COLUMN CAUGHT FIRE DUE TO POSSIBLE RECALL COMPONENT FAILURE (99V-124), HOWEVER DENIED BY DEALERSHIP. MJS.Vehicle was on fire. Vehicle Identification Number (VIN):2FALP74WXPX. FORD CROWN VICTORIA 1993 problem was reported in WOODBURY H, NJ. Vehicle was not using Cruise Control. FORD CROWN VICTORIA 1993 drive type:RWD. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #852593

FORD CROWN VICTORIA 1993 car safety problem was reported on Aug 01, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN . THE DEFECTIVE ODOMETER IS INOPERATIVE. DEALER NEEDS TO REPLACE THE ODOMETER SYSTEM. DEALER CANNOT DETERMINE THE CAUSE OF THE PROBLEM. PLEASE PROVIDE FURTHER INFORMATION. *AK.Vehicle Identification Number (VIN):PLEASE FILL. FORD CROWN VICTORIA 1993 problem was reported in SUNNY ISLE BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #714657

FORD CROWN VICTORIA 1993 car safety problem was reported on July 23, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:WINDSHIELD WIPER/WASHER:MOTOR . THE PULSE WINDSHIELD WIPER DOES NOT ENGAGE AT CERTAIN SETTINGS. AT OTHER TIMES, THE PULSE WIPER BECOMES INOPERABLE WHEN ENGAGING THE TURN INDICATOR, CAUSING VISUAL PROBLEMS DURING RAIN/SNOW. INSTALLING A NEW BATTERY HELPED FOR A WHILE, BUT THE SAME PROBLEMS EVENTUALLY RETURNED. IT APPEARS TO BE A SHORT-CIRCUIT/GROUNDING PROBLEM OF SOME TYPE. THE INDEPENDENT FRONT-END SUSPENSION PROBLEM CONCERNS A CRACKING SOUND OF METAL ON THE FRONT-PASSENGER SIDE WHEN THE WHEEL IS TURNED SHARPLY TO THE RIGHT. THIS PROBLEM OCCURS INFREQUENTLY, BUT HAS BEEN NOTICED SINCE EARLY PURCHASE DATE. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP73W8PX. FORD CROWN VICTORIA 1993 problem was reported in SHARON, MA. Original Owner. Vehicle was purchased on 19930701. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 5 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #714657

FORD CROWN VICTORIA 1993 car safety problem was reported on July 23, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT . THE PULSE WINDSHIELD WIPER DOES NOT ENGAGE AT CERTAIN SETTINGS. AT OTHER TIMES, THE PULSE WIPER BECOMES INOPERABLE WHEN ENGAGING THE TURN INDICATOR, CAUSING VISUAL PROBLEMS DURING RAIN/SNOW. INSTALLING A NEW BATTERY HELPED FOR A WHILE, BUT THE SAME PROBLEMS EVENTUALLY RETURNED. IT APPEARS TO BE A SHORT-CIRCUIT/GROUNDING PROBLEM OF SOME TYPE. THE INDEPENDENT FRONT-END SUSPENSION PROBLEM CONCERNS A CRACKING SOUND OF METAL ON THE FRONT-PASSENGER SIDE WHEN THE WHEEL IS TURNED SHARPLY TO THE RIGHT. THIS PROBLEM OCCURS INFREQUENTLY, BUT HAS BEEN NOTICED SINCE EARLY PURCHASE DATE. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP73W8PX. FORD CROWN VICTORIA 1993 problem was reported in SHARON, MA. Original Owner. Vehicle was purchased on 19930701. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 5 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #850549

FORD CROWN VICTORIA 1993 car safety problem was reported on Aug 27, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE . WHILE DRIVING ON THE HIGHWAY OIL LIGHT CAME ON. VEHICLE MADE UNUSUALL NOISES, AND DIDN'T WANT TO MOVE. HAD THE VEHICLE TOWED TO THE DEALER. OIL PUMP FAILED TO DISTRIBUTE OIL IN THE ENGINE. ALSO, DEALER CLEANED AND REPAIRED OIL FILTER, AND REPLACED FRONT BRAKE ROTORS AND PADS. *AK.Vehicle Identification Number (VIN):2FALP74W5PX. FORD CROWN VICTORIA 1993 problem was reported in CARLSTADT, NJ. Original Owner. Vehicle was purchased on 19930615. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 55 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #850549

FORD CROWN VICTORIA 1993 car safety problem was reported on Aug 27, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC . WHILE DRIVING ON THE HIGHWAY OIL LIGHT CAME ON. VEHICLE MADE UNUSUALL NOISES, AND DIDN'T WANT TO MOVE. HAD THE VEHICLE TOWED TO THE DEALER. OIL PUMP FAILED TO DISTRIBUTE OIL IN THE ENGINE. ALSO, DEALER CLEANED AND REPAIRED OIL FILTER, AND REPLACED FRONT BRAKE ROTORS AND PADS. *AK.Vehicle Identification Number (VIN):2FALP74W5PX. FORD CROWN VICTORIA 1993 problem was reported in CARLSTADT, NJ. Original Owner. Vehicle was purchased on 19930615. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 55 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #850549

FORD CROWN VICTORIA 1993 car safety problem was reported on Aug 27, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE . WHILE DRIVING ON THE HIGHWAY OIL LIGHT CAME ON. VEHICLE MADE UNUSUALL NOISES, AND DIDN'T WANT TO MOVE. HAD THE VEHICLE TOWED TO THE DEALER. OIL PUMP FAILED TO DISTRIBUTE OIL IN THE ENGINE. ALSO, DEALER CLEANED AND REPAIRED OIL FILTER, AND REPLACED FRONT BRAKE ROTORS AND PADS. *AK.Vehicle Identification Number (VIN):2FALP74W5PX. FORD CROWN VICTORIA 1993 problem was reported in CARLSTADT, NJ. Original Owner. Vehicle was purchased on 19930615. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 55 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #850549

FORD CROWN VICTORIA 1993 car safety problem was reported on Aug 27, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with OTHER . WHILE DRIVING ON THE HIGHWAY OIL LIGHT CAME ON. VEHICLE MADE UNUSUALL NOISES, AND DIDN'T WANT TO MOVE. HAD THE VEHICLE TOWED TO THE DEALER. OIL PUMP FAILED TO DISTRIBUTE OIL IN THE ENGINE. ALSO, DEALER CLEANED AND REPAIRED OIL FILTER, AND REPLACED FRONT BRAKE ROTORS AND PADS. *AK.Vehicle Identification Number (VIN):2FALP74W5PX. FORD CROWN VICTORIA 1993 problem was reported in CARLSTADT, NJ. Original Owner. Vehicle was purchased on 19930615. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 55 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #548846

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR . CONVERTERS FAILED. YH.FORD CROWN VICTORIA 1993 problem was reported in METAIRIE, LA. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #548846

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . CRUISE CONTROL IS DEFECTIVE. YH.FORD CROWN VICTORIA 1993 problem was reported in METAIRIE, LA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #548846

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . AUTOMATIC TRANSMISSION MALFUNCTIONS. YH.FORD CROWN VICTORIA 1993 problem was reported in METAIRIE, LA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #548846

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:IGNITION . INFFERIOR SPARK PLUG WIRING CAUSED ELECTICAL CUT OUT. YH.FORD CROWN VICTORIA 1993 problem was reported in METAIRIE, LA. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #548846

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR . CONVERTERS FAILED. YH.FORD CROWN VICTORIA 1993 problem was reported in METAIRIE, LA. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #548846

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:IGNITION . INFFERIOR SPARK PLUG WIRING CAUSED ELECTICAL CUT OUT. YH.FORD CROWN VICTORIA 1993 problem was reported in METAIRIE, LA. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #548846

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . CRUISE CONTROL IS DEFECTIVE. YH.FORD CROWN VICTORIA 1993 problem was reported in METAIRIE, LA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #548846

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . AUTOMATIC TRANSMISSION MALFUNCTIONS. YH.FORD CROWN VICTORIA 1993 problem was reported in METAIRIE, LA. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #604631

FORD CROWN VICTORIA 1993 car safety problem was reported on Mar 30, 1994.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with OTHER . CUP HOLDER SPRING FAILED. NLM.Vehicle Identification Number (VIN):2FALP74W7PX. FORD CROWN VICTORIA 1993 problem was reported in FORT WAYNE, IN. Vehicle was purchased on 19940321. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #604631

FORD CROWN VICTORIA 1993 car safety problem was reported on Mar 30, 1994.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SEATS . FRONT SEAT TRACK FAILED. NLM.Vehicle Identification Number (VIN):2FALP74W7PX. FORD CROWN VICTORIA 1993 problem was reported in FORT WAYNE, IN. Vehicle was purchased on 19940321. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #854871

FORD CROWN VICTORIA 1993 car safety problem was reported on Dec 24, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:ANTILOCK . ABS BRAKING SYSTEM MALFUNCTIONED, CAUSING STEERING TO LOCK UP AND NO BRAKING ABILITY, WHICH MAY HAVE CAUSED A CRASH. PLEASE PROVIDE FURTHER INFORMATION. *AK.Vehicle Identification Number (VIN):2FA7P72W918. FORD CROWN VICTORIA 1993 problem was reported in WEST HEMPSTEAD, NY. Original Owner. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #718345

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 27, 2000.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE:GASOLINE . NO SUMMARY LISTED FOR ABOVE VEHICLE. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP73WXPX. FORD CROWN VICTORIA 1993 problem was reported in MIDLOTHIAN, VA. Original Owner. Vehicle was purchased on 19960301. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #857322

FORD CROWN VICTORIA 1993 car safety problem was reported on June 01, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC . BRAKING SYSTEM MALFUNCTIONED, CAUSING EXTENDED STOPPING DISTANCE WHICH MAY RESULT IN A CRASH. DEALER REPLACED BRAKE CALIPERS AND FRONT DISC ROTORS 3 TIMES. ALSO, WIRING HARNESS IN THE STEERING COLUMN BURNED OUT(IGNITION), CAUSING A FIRE. IN ADDITION, BOLT THAT HOLDS DRIVER'S SEAT TO THE FLOOR CAME OUT WHICH COULD CAUSE THE DRIVER'S SEAT TO MOVE UNEXPECTEDLY. PLEASE PROVIDE FURTHER INFORMATION. *AK.Vehicle was involved in a crash. Vehicle was on fire. Vehicle Identification Number (VIN):2FALP74XPXP. FORD CROWN VICTORIA 1993 problem was reported in WOODBURY HEIGHTS, NJ. Original Owner. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #857322

FORD CROWN VICTORIA 1993 car safety problem was reported on June 01, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SEATS . BRAKING SYSTEM MALFUNCTIONED, CAUSING EXTENDED STOPPING DISTANCE WHICH MAY RESULT IN A CRASH. DEALER REPLACED BRAKE CALIPERS AND FRONT DISC ROTORS 3 TIMES. ALSO, WIRING HARNESS IN THE STEERING COLUMN BURNED OUT(IGNITION), CAUSING A FIRE. IN ADDITION, BOLT THAT HOLDS DRIVER'S SEAT TO THE FLOOR CAME OUT WHICH COULD CAUSE THE DRIVER'S SEAT TO MOVE UNEXPECTEDLY. PLEASE PROVIDE FURTHER INFORMATION. *AK.Vehicle was involved in a crash. Vehicle was on fire. Vehicle Identification Number (VIN):2FALP74XPXP. FORD CROWN VICTORIA 1993 problem was reported in WOODBURY HEIGHTS, NJ. Original Owner. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #857322

FORD CROWN VICTORIA 1993 car safety problem was reported on June 01, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:WIRING:FRONT UNDERHOOD . BRAKING SYSTEM MALFUNCTIONED, CAUSING EXTENDED STOPPING DISTANCE WHICH MAY RESULT IN A CRASH. DEALER REPLACED BRAKE CALIPERS AND FRONT DISC ROTORS 3 TIMES. ALSO, WIRING HARNESS IN THE STEERING COLUMN BURNED OUT(IGNITION), CAUSING A FIRE. IN ADDITION, BOLT THAT HOLDS DRIVER'S SEAT TO THE FLOOR CAME OUT WHICH COULD CAUSE THE DRIVER'S SEAT TO MOVE UNEXPECTEDLY. PLEASE PROVIDE FURTHER INFORMATION. *AK.Vehicle was involved in a crash. Vehicle was on fire. Vehicle Identification Number (VIN):2FALP74XPXP. FORD CROWN VICTORIA 1993 problem was reported in WOODBURY HEIGHTS, NJ. Original Owner. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #857322

FORD CROWN VICTORIA 1993 car safety problem was reported on June 01, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS . BRAKING SYSTEM MALFUNCTIONED, CAUSING EXTENDED STOPPING DISTANCE WHICH MAY RESULT IN A CRASH. DEALER REPLACED BRAKE CALIPERS AND FRONT DISC ROTORS 3 TIMES. ALSO, WIRING HARNESS IN THE STEERING COLUMN BURNED OUT(IGNITION), CAUSING A FIRE. IN ADDITION, BOLT THAT HOLDS DRIVER'S SEAT TO THE FLOOR CAME OUT WHICH COULD CAUSE THE DRIVER'S SEAT TO MOVE UNEXPECTEDLY. PLEASE PROVIDE FURTHER INFORMATION. *AK.Vehicle was involved in a crash. Vehicle was on fire. Vehicle Identification Number (VIN):2FALP74XPXP. FORD CROWN VICTORIA 1993 problem was reported in WOODBURY HEIGHTS, NJ. Original Owner. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #857993

FORD CROWN VICTORIA 1993 car safety problem was reported on Mar 03, 2000.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:PARK/NEUTRAL START SWITCH . WHILE IN PARK POSITION WITH KEY OUT OF THE IGNITION, AND EMERGENCY PARKING BRAKE ACTIVATED, VEHICLE SUDDENLY MOVED FORWARD AND CAUSED A CRASH. AFTER THE CRASH, THE OCCUPANT COULD NOT START VEHICLE AND MOVE IT OUT OF PARK POSITION. PLEASE PROVIDE FURTHER INFORMATION. *AK.Vehicle was involved in a crash. Vehicle Identification Number (VIN):2FALP74W2PX. FORD CROWN VICTORIA 1993 problem was reported in TUXEDO, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #858180

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL:LINKAGES . WHILE APPLYING THE BRAKES VEHICLE SUDDENLY AND UNEXPECTEDLY ACCELERATED, RESULTING IN A COLLISION. *AK.Vehicle was involved in a crash. FORD CROWN VICTORIA 1993 problem was reported in FORTY FORT, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #549179

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:WIRING . WIRES IN THE STEERING COLUMN CAUGHT FIRE. NLM.Vehicle was on fire. FORD CROWN VICTORIA 1993 problem was reported in WOODBURY H, NJ. Original Owner. Vehicle was purchased on 19931001. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:FWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #549179

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SEATS . DRIVERS SEAT BOLT CAME OUT OF THE FRAME AND IT CANNOT BE WELDED BECAUSE THE METAL IS TO SOFT. NLM.Vehicle was on fire. FORD CROWN VICTORIA 1993 problem was reported in WOODBURY H, NJ. Original Owner. Vehicle was purchased on 19931001. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:FWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #9000308

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SEATS . DRIVERS SEAT CAME LOSE FROM THE FLOOR BOARD..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W1PX. FORD CROWN VICTORIA 1993 problem was reported in GLEN BURNIE, MD. Vehicle was purchased on 19930101. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #861551

FORD CROWN VICTORIA 1993 car safety problem was reported on Apr 24, 2000.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING:LINKAGES:TIE ROD ASSEMBLY . WHILE BACKING OUT OF THE GARAGE AND WITHOUT WARNING INNER TIE ROD BROKE, CAUSE UNKNOWN. *AK.Vehicle Identification Number (VIN):2FALP74W8PX. FORD CROWN VICTORIA 1993 problem was reported in HOLLAND PATTENT, NY. Vehicle was purchased on 19950301. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #722271

FORD CROWN VICTORIA 1993 car safety problem was reported on June 01, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . CRUISE CONTROL FAILED, RESEMBLES NHTSA CAMPAIGN NUMBER 99V124000 MINUS UNDERHOOD FIRE. CONTACTED FORD 05-04-00 - RESPONSE NOT ON THEIR VIN LIST OF AFFECTED VEHICLES. *AK REFERENCED IN EA02-025.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W2PX. FORD CROWN VICTORIA 1993 problem was reported in ROSWELL, GA. Vehicle was purchased on 19950901. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL TYPE: GAS.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #863662

FORD CROWN VICTORIA 1993 car safety problem was reported on June 01, 2000.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SEATS . WHILE PULLING OUT OF A LOT AT APPROXIMATELY 3-5 MPH VEHICLE STRUCK A POLE, CAUSING LEFT FRONT ANCHOR BOLT TO PULL OUT OF THE SEAT. DEALER/MANUFACTURER WERE NOT CONTACTED AT THIS TIME. FEEL FREE TO PROVIDE FUTHER DETAILS. *AK.Vehicle was involved in a crash. Vehicle Identification Number (VIN):2FALP74UXPX. FORD CROWN VICTORIA 1993 problem was reported in HAGERSTOWN, MD. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #724263

FORD CROWN VICTORIA 1993 car safety problem was reported on Apr 01, 2000.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE:GASOLINE . E-MAIL REPLY IS ACCEPTABLE. NO SAFETY DEFECT LISTED IN SUMMARY. *AK.Vehicle Identification Number (VIN):2FACP74W7PX. FORD CROWN VICTORIA 1993 problem was reported in WARREN, MI. Original Owner. Vehicle was purchased on 19940201. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 1 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #724036

FORD CROWN VICTORIA 1993 car safety problem was reported on Aug 01, 1994.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE:GASOLINE . HAD TO TAKE CAR TO DEALER 3 TIMES WITH TRANSMISSION TROUBLE CAR WOULD NOT SHIFT TO THE NEXT GEAR EACH TIME THE DEALER ADVISED THE PROBLEM WAS WITH THE COMPUTER SYSTEM AND I HAD TO PAY FOR THE WORK DONE AND THEN THE TRANSMISSION WENT OUT AT 600098 MI (98 OVER THE 60,000 MI WARRANTY) AND DEALER WOULD NOT COVER CAR HAD TO HAVE AND PAY FOR A NEW TRANSMISSION THEN 1 MONTH LATER THE ENGINE HAD TO BE REPLACED AGAIN THE DEALER WOULD NOT BE RESPONSIBLE THE SHOP THAT PUT THE NEW ENGINE IN SAID IT WAS CAUSED BY THE COMPUTER SYSTEM AND THAT ALOT OF CR VICS FROM THE 1993 YEAR (1ST YEAR FOR THAT MODEL) HAD TROUBLE (EX THE POLICE CARS IN MEMPHIS) AFTER HAVING A NEW TRANSMISSION AND ENGINE THE CAR DID FINE UNTIL 0301200 HAD TO HAVE A NEW TRANSMISSION AGAIN AND THE SHOP IS UNABLE TO MAKE IT RIGHT DUE TO THE COMPUTER SYSTEM, THIS SHOP PUT A 2ND TRANSMISSION IN 06/2000 AND SAID I HAD ENGINE PROBLEMS REASON FOR TRANSMISSION TROUBLE. THIS CAR IS A LEMON AND HAS MULTIPLE DEFECTS EVIDENTLY WITH THE COMPUTER SYSTEM. *AK.Vehicle Identification Number (VIN):2FALP73W0PX. FORD CROWN VICTORIA 1993 problem was reported in MEMPHIS, TN. Original Owner. Vehicle was purchased on 19920701. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:FWD. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 40 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #724036

FORD CROWN VICTORIA 1993 car safety problem was reported on Aug 01, 1994.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . HAD TO TAKE CAR TO DEALER 3 TIMES WITH TRANSMISSION TROUBLE CAR WOULD NOT SHIFT TO THE NEXT GEAR EACH TIME THE DEALER ADVISED THE PROBLEM WAS WITH THE COMPUTER SYSTEM AND I HAD TO PAY FOR THE WORK DONE AND THEN THE TRANSMISSION WENT OUT AT 600098 MI (98 OVER THE 60,000 MI WARRANTY) AND DEALER WOULD NOT COVER CAR HAD TO HAVE AND PAY FOR A NEW TRANSMISSION THEN 1 MONTH LATER THE ENGINE HAD TO BE REPLACED AGAIN THE DEALER WOULD NOT BE RESPONSIBLE THE SHOP THAT PUT THE NEW ENGINE IN SAID IT WAS CAUSED BY THE COMPUTER SYSTEM AND THAT ALOT OF CR VICS FROM THE 1993 YEAR (1ST YEAR FOR THAT MODEL) HAD TROUBLE (EX THE POLICE CARS IN MEMPHIS) AFTER HAVING A NEW TRANSMISSION AND ENGINE THE CAR DID FINE UNTIL 0301200 HAD TO HAVE A NEW TRANSMISSION AGAIN AND THE SHOP IS UNABLE TO MAKE IT RIGHT DUE TO THE COMPUTER SYSTEM, THIS SHOP PUT A 2ND TRANSMISSION IN 06/2000 AND SAID I HAD ENGINE PROBLEMS REASON FOR TRANSMISSION TROUBLE. THIS CAR IS A LEMON AND HAS MULTIPLE DEFECTS EVIDENTLY WITH THE COMPUTER SYSTEM. *AK.Vehicle Identification Number (VIN):2FALP73W0PX. FORD CROWN VICTORIA 1993 problem was reported in MEMPHIS, TN. Original Owner. Vehicle was purchased on 19920701. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:FWD. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 40 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #865583

FORD CROWN VICTORIA 1993 car safety problem was reported on Feb 01, 2000.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL:ACCELERATOR PEDAL . WHILE DRIVING AND LETTING OFF THE GAS PEDAL, VEHICLE CONTINUES AND WON'T SLOW DOWN. PLEASE PROVIDE FURTHER INFORMATION.*AK.Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in RICHMOND, TX. Original Owner. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #869740

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SEATS . THE BOLTS HOLDING DRIVER'S SEAT TO THE FRAME SHEARED OFF, CAUSING SEAT TO BE UNSTABLE. DEALER HAS INSPECTED VEHICLE.*AK.FORD CROWN VICTORIA 1993 problem was reported in LAFAYETTE, LA. Original Owner. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #552243

FORD CROWN VICTORIA 1993 car safety problem was reported on July 07, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . DURING RECALL REPAIR 99V-124 OF THE SPPED CONTROL DEACTIVATION SWITCH CONSUMER FEELS DEALER MADE ADDITIONAL REPAIRS (DRIVE BELT, DIAGNOSTIC TEST, T-CONNECTOR AND HOSE FOR PCV) THAT WERE UNNEEDED. NLM.Vehicle Identification Number (VIN):2FALP74W5PX. FORD CROWN VICTORIA 1993 problem was reported in YUKON, OK. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #555255

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with EXTERIOR LIGHTING:HEADLIGHTS . HEAD LIGHTS ARE GIVING POOR LIGHTING. *SLC .Vehicle Identification Number (VIN):2FALP74W2PX. FORD CROWN VICTORIA 1993 problem was reported in KEYSER, WV. Vehicle was purchased on 19930120. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #874128

FORD CROWN VICTORIA 1993 car safety problem was reported on Sept 30, 2000.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE:GASOLINE . WHILE DRIVING ABOUT 60 MPH ENGINE SHUT OFF WITHOUT A PRIOR WARNING. CONSUMER HAS TO DRIVE OFF ROAD AND RESTART ENGINE AGAIN, THEN IT WILL WORK.*AK ENGINE SHUTS OFF WHEN THE DRIVER USES THE BRAKE OR WHEN CHANGES LANES. *YH.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W4PX. FORD CROWN VICTORIA 1993 problem was reported in CHICAGO, IL. Original Owner. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #556003

FORD CROWN VICTORIA 1993 car safety problem was reported on Aug 03, 2000.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE:GASOLINE . WHILE DRIVING THE VEHICLE COMPLETELY SHUT OFF CAUSING LOSS OF POWER STEERING AND BRAKES. NLM.FORD CROWN VICTORIA 1993 problem was reported in BARBERTON, OH. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #557039

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:ANTILOCK . THE ANTI-LOCK BRAKE CYLINDER ON THE DRIVER'S SIDE AND REAR PASSENGER SIDE HAVE BOTH GONE OUT, THE BRAKES ATTEMPT TO LOCK AT TIMES WHEN THE VEHICLE IS BEING DRIVEN. *SLC.Vehicle Identification Number (VIN):2FACP74W4PX. FORD CROWN VICTORIA 1993 problem was reported in LOS ANGELES, CA. Vehicle was purchased on 19950823. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #557039

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT:SPRINGS:AIR SUSPENSION SYSTEM . REAR SUSPENSION AIR BAGS LEAK, CAUSING THE VEHICLE TO BE UNABLE TO RAISE UP AND THE ENGINE TO CONSTANTLY RUN. *SLC.Vehicle Identification Number (VIN):2FACP74W4PX. FORD CROWN VICTORIA 1993 problem was reported in LOS ANGELES, CA. Vehicle was purchased on 19950823. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #736604

FORD CROWN VICTORIA 1993 car safety problem was reported on July 01, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with EXTERIOR LIGHTING:HEADLIGHTS . ENGINE CHECK LIGHT COMES ON AT VARIOUS MPH EACH TIME CAR IS DRIVEN. MECHANICS DO NOT KNOW THE CAUSE. WE HAVE SPENT OVER $500 TRYING TO GET IT FIXED. REGARDING THE LIGHTS, MOISTURE FORMS BEHIND THE LIGHT COVERS DURING COOL OR DAMP WEATHER. IN MY ESTIMATION, THIS IS A SAFETY HAZZARD WHEN DRIVING AT NIGHT DUE TO DECREASED VISIBILITY..Vehicle Identification Number (VIN):2FACP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in DALLAS, TX. Vehicle was purchased on 19931101. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #736604

FORD CROWN VICTORIA 1993 car safety problem was reported on July 01, 1999.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with OTHER . ENGINE CHECK LIGHT COMES ON AT VARIOUS MPH EACH TIME CAR IS DRIVEN. MECHANICS DO NOT KNOW THE CAUSE. WE HAVE SPENT OVER $500 TRYING TO GET IT FIXED. REGARDING THE LIGHTS, MOISTURE FORMS BEHIND THE LIGHT COVERS DURING COOL OR DAMP WEATHER. IN MY ESTIMATION, THIS IS A SAFETY HAZZARD WHEN DRIVING AT NIGHT DUE TO DECREASED VISIBILITY..Vehicle Identification Number (VIN):2FACP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in DALLAS, TX. Vehicle was purchased on 19931101. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #557906

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . THE ACCELERATOR STUCK WHILE BACKING OUT OF A PARKING LOT CAUSING THE CAR TO HIT TWO OTHER VEHICLES WHICH WERE PARKED, PASSENGER SUFFERED FRACTURED RIBS AND MULTIPLE BRUISES, DRIVER SUSTAINED BRUISED CHEST FROM HITTING THE STEERING WHEEL, VEHICLE WAS TOTALED. NLM.1 person(s) were injured. Vehicle Identification Number (VIN):2FALP74V8PX. FORD CROWN VICTORIA 1993 problem was reported in LA HABRA, CA. Original Owner. Vehicle was purchased on 19930726. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #877881

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 01, 1995.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER . IN OCTOBER 1995 TORQUE CONVERTER HAD TO BE REPLACED. FORD PAID 50 %, THERE WAS A TSB 931211 ON IT. CURRENTLY, SAME THING HAS HAPPENED AGAIN. FORD REFUSED TO ASSIST IN REPAIR EXPENSES. *AK.Vehicle Identification Number (VIN):2FACP74W2PX. FORD CROWN VICTORIA 1993 problem was reported in FORT MEYERS, FL. Original Owner. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #738489

FORD CROWN VICTORIA 1993 car safety problem was reported on Dec 04, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . ON 12/4/96 MY VEHICLE'S TRANSMISSION STARTED SLIPPING.IT WAS STILL UNDER WARRANTY AT THAT TIME.IT WAS TAKEN INTO THE FORD DEALERSHIP,WHERE WE WERE TOLD THAT THEY HAD BEEN HAVING PROBLEMS TORQUE CONVERTERS ON THESE VEHICLES.A TORK FLUSH WAS PERFORMED AND THEY TOLD US EVERYTHING WOULD BE OK.THE VEHICLE HAS 30,000 AT THAT TIME.ON 6/2/99 WE STARTED EXPERIENCING THE SAME PROBLEM.IT AGAIN WAS TAKEN INTO THE FORD DEALERSHIP,WHERE AGAIN THEY STATED THE TORK CONVERTER WAS BAD AND THEY TOLD US AGAIN THAT A TORK FLUSH WOULD BE NEEDED.THE VEHICLE AT THIS TIME HAD 70,000.I ADDRESSED THE PROBLEM AT THAT TIME AND ASKED WHY THE TRANSMISSION COULD NOT BE REPAIRED VS. JUST A TORK FLUSH.I WAS TOLD " FORD MOTOR WILL ONLY FLUSH". ON 12/18/00 MY VEHICLE AGAIN STARTED EXPERIENCING PROBLEMS. IT WOULD NOW NOT GO INTO "DRIVE". THE CAR HAS 90,000 ON IT NOW. THE VEHICLE WAS TAKEN TO THE SHOP AND I WAS TOLD THAT THE WHOLE TRANSMISSION IS OUT. ON SEVERAL OCCASIONS I HAVE EXPRESSED MY CONCERN REGARDING FLUSHING VS ACTUALLY CHECKING INTO THE TRANSMISSIONS AND STILL WAS TOLD THAT FORD WILL NOT DO THAT, THEY WILL ONLY DO THE FLUSH. NOW I'M STUCK WITH A CAR WITH ONLY 90,000 ON IT AND A TRANSMISSION THAT HAS TO BE COMPLETELY REBUILT. WHAT EVER HAPPENED TO "FORD STANDS BEHIND THEIR PRODUCT" OR "YOUR SATISFACTION IS OUR #1 GOAL." I HAVE CALLED CUSTOMER SERVICE ON SEVERAL OCCASIONS AND TO DATE I HAVE NOT ONCE GOTTEN A CALL BACK. I HAVE DECIDED THAT THE ONLY WAY TO RECTIFY THIS PROBLEM IS TO VOICE MY CONCERN MY GOING PUBLIC ON TV. WE HAVE A TV STATION HERE CALLED "CALL FOR ACTION" MAYBE THAT IS MY NEXT STEP. CALLING AND EXPRESSING MYSELF TO FORD DOES NOT SEEM TO HELP. IF FORD REALLY STOOD BEHIND THEIR VEHICLES, I WOULD NOT BE SITTING WITH A CAR WITH ONLY 90,000 MILES ON IT WITH A BLOWN TRANSMISSION. IF THE PROBLEM WOULD HAVE BE CORRECTED IN 1996 WHEN I ORIGINALLY REPORTED THE PROBLEM, THEN MAYBE I WOULD STILL BE DRIVING THE CAR.I LOVE MY CAR, ITS FORD MOTOR COMPANY I AM NOT HAPPY WITH..Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in OLATHE, KS. Original Owner. Vehicle was purchased on 19931001. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #738489

FORD CROWN VICTORIA 1993 car safety problem was reported on Dec 04, 1996.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER . ON 12/4/96 MY VEHICLE'S TRANSMISSION STARTED SLIPPING.IT WAS STILL UNDER WARRANTY AT THAT TIME.IT WAS TAKEN INTO THE FORD DEALERSHIP,WHERE WE WERE TOLD THAT THEY HAD BEEN HAVING PROBLEMS TORQUE CONVERTERS ON THESE VEHICLES.A TORK FLUSH WAS PERFORMED AND THEY TOLD US EVERYTHING WOULD BE OK.THE VEHICLE HAS 30,000 AT THAT TIME.ON 6/2/99 WE STARTED EXPERIENCING THE SAME PROBLEM.IT AGAIN WAS TAKEN INTO THE FORD DEALERSHIP,WHERE AGAIN THEY STATED THE TORK CONVERTER WAS BAD AND THEY TOLD US AGAIN THAT A TORK FLUSH WOULD BE NEEDED.THE VEHICLE AT THIS TIME HAD 70,000.I ADDRESSED THE PROBLEM AT THAT TIME AND ASKED WHY THE TRANSMISSION COULD NOT BE REPAIRED VS. JUST A TORK FLUSH.I WAS TOLD " FORD MOTOR WILL ONLY FLUSH". ON 12/18/00 MY VEHICLE AGAIN STARTED EXPERIENCING PROBLEMS. IT WOULD NOW NOT GO INTO "DRIVE". THE CAR HAS 90,000 ON IT NOW. THE VEHICLE WAS TAKEN TO THE SHOP AND I WAS TOLD THAT THE WHOLE TRANSMISSION IS OUT. ON SEVERAL OCCASIONS I HAVE EXPRESSED MY CONCERN REGARDING FLUSHING VS ACTUALLY CHECKING INTO THE TRANSMISSIONS AND STILL WAS TOLD THAT FORD WILL NOT DO THAT, THEY WILL ONLY DO THE FLUSH. NOW I'M STUCK WITH A CAR WITH ONLY 90,000 ON IT AND A TRANSMISSION THAT HAS TO BE COMPLETELY REBUILT. WHAT EVER HAPPENED TO "FORD STANDS BEHIND THEIR PRODUCT" OR "YOUR SATISFACTION IS OUR #1 GOAL." I HAVE CALLED CUSTOMER SERVICE ON SEVERAL OCCASIONS AND TO DATE I HAVE NOT ONCE GOTTEN A CALL BACK. I HAVE DECIDED THAT THE ONLY WAY TO RECTIFY THIS PROBLEM IS TO VOICE MY CONCERN MY GOING PUBLIC ON TV. WE HAVE A TV STATION HERE CALLED "CALL FOR ACTION" MAYBE THAT IS MY NEXT STEP. CALLING AND EXPRESSING MYSELF TO FORD DOES NOT SEEM TO HELP. IF FORD REALLY STOOD BEHIND THEIR VEHICLES, I WOULD NOT BE SITTING WITH A CAR WITH ONLY 90,000 MILES ON IT WITH A BLOWN TRANSMISSION. IF THE PROBLEM WOULD HAVE BE CORRECTED IN 1996 WHEN I ORIGINALLY REPORTED THE PROBLEM, THEN MAYBE I WOULD STILL BE DRIVING THE CAR.I LOVE MY CAR, ITS FORD MOTOR COMPANY I AM NOT HAPPY WITH..Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in OLATHE, KS. Original Owner. Vehicle was purchased on 19931001. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #886033

FORD CROWN VICTORIA 1993 car safety problem was reported on Apr 05, 2001.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE:GASOLINE . VEHICLE PARKED, CONSUMER STARTED ENGINE, USED AIR CONDITIONER FOR 12 TO 15 MINUTES, AND SHUT ENGINE OFF AGAIN. ONE HALF HOUR LATER,VEHICLE WAS BURNING, FIRE DEPARTMENT STATED FIRE STARTED IN ENGINE RUNNING GEAR. VEHICLE TOTALLED. *AK *SLC REFERENCED IN RQ01-002.Vehicle was on fire. Vehicle Identification Number (VIN):2FACP74W5PX. FORD CROWN VICTORIA 1993 problem was reported in HOUSTON, TX. Vehicle was purchased on 20000811. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #743896

FORD CROWN VICTORIA 1993 car safety problem was reported on Apr 01, 2001.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with TIRES . THESE TIRES ARE PURPORTEDLY GOOD FOR 3 YEARS OR 70,000 MILES. THEY ARE ALSO SUPPOSE TO BE GOOD UP TO 112 MPH. HOWEVER, WHEN THE PREVIOUS OWNER LEARNED OF OUR WRECK , HE PROVIDED ME WITH RECEIPTS WHICH SHOWED THAT TWO OTHER TIRES FROM THE ORIGINAL FOUR FAILED AT 153,240 MILES AND 143,911 MILES. HE ORIGINALLY BOUGHT THEM AT 106562 MILES. THESE TIRES ARE TOUTED AS GOOD FOR 70,000 MILES AND THEY ARE GOING TO GET SOMEONE KILLED. MARVIN MORRIS AT 281-579-2174 WITNESSED THE TIRE SHREDDING AS DID KAWAL PATEL AT 281-575-4360 (ALSO 281-693-2353).*AK (DOT NUMBER: 0B34PT0070 TIRESIZE: 215/70R15).Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74WXPX. FORD CROWN VICTORIA 1993 problem was reported in BOSSIER CITY, LA. Accident was reported to Police. Vehicle was purchased on 20001101. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL TYPE: GAS. VEHICLE SPEED: 75 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #743808

FORD CROWN VICTORIA 1993 car safety problem was reported on Apr 09, 2001.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING:LINKAGES . WHILE BACKING OUT FROM A PARKING SPACE FROM A STAND STILL, LEFT TIE ROD BROKE WITHOUT WARNING. VEHICLE COULD NOT BE STEERED AND HAD TO BE TOWED.*AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W8PX. FORD CROWN VICTORIA 1993 problem was reported in NEW HAVEN, CT. Vehicle was purchased on 19950801. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #744334

FORD CROWN VICTORIA 1993 car safety problem was reported on Apr 11, 2001.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with TIRES . ON WEDNESDAY, APRIL 11, 2001 AT APPROXIMATELY 2:15 PM CDT, A FIRESTONE PASSENGER CAR TIRE FT70C FLATTENED AND DISINTEGRATED AT 70+ MPH ON INTERSTATE 40 EASTBOUND MILE MARKER 262. THE VEHICLE WAS A 1993 FORD CROWN VICTORIA. THE TIRE WAS ON THE RIGHT FRONT. I WAS ABLE TO KEEP CONTROL AND GET TO THE SIDE OF THE ROAD WITHOUT FURTHER INCIDENT.*AIK (DOT NUMBER: EL34 TIRESIZE: P215/70R15).0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP73W1PX. FORD CROWN VICTORIA 1993 problem was reported in HENDERSONVILLE, TN. Original Owner. Vehicle was purchased on 19930701. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 75 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #886956

FORD CROWN VICTORIA 1993 car safety problem was reported on July 01, 2000.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with EXTERIOR LIGHTING:HEADLIGHTS . HEADLIGHT COVERS ARE DISCOLORED SO BADLY THAT CONSUMER IS NO LONGER ABLE TO DRIVE AT NIGHT, VISIBILITY IS GREATLY REDUCED.*AK.Vehicle Identification Number (VIN):2FACP71W3PX. FORD CROWN VICTORIA 1993 problem was reported in COMMERCE, GA. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #744636

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:WINDSHIELD . WE HAD TO HAVE THREE OF THE CARS WINDOWS WORKED ON - THEY WOULD NOT GO UP OR DOWN. NOW THE DRIVER SIDE WINDOW HAS QUIT WORKING A SECOND TIME. WE DO NOT EXCESSIVELY USE THE WINDOWS. I AM THE SOLE DRIVER OF THE CAR AND USUSALLY JUST TAKE IT TO WORK 2 MILES AWAY FROM HOME AND BACK. I USE THE AC. EACH TIME WE HAVE THE WINDOWS REPAIRED IT IS $200 OR GREATER. SO FAR WE HAVE $600 INTO THE WINDOWS. WE WILL PROBABLY NOT FIX THEM ANYMORE WHEN THEY BREAK. WE UNDERSTAND FROM CRUISING THE INTERNET THAT THIS IS A COMMON COMPLAINT WITH THIS MAKE AND MODEL AND YEAR OF CAR. IS THERE ANYTHING THAT CAN BE DONE? WHEN THE DRIVER SIDE WINDOW QUIT WORKING FOR THE SECOND TIME, THAT WAS REALLY ANNOYING. WHENEVER I NEED TO USE THAT WINDOW (MORE FREQUENTLY THAN THE OTHERS)- I HAVE TO OPEN THE DOOR GET OUT OF THE CAR.*AK.Vehicle Identification Number (VIN):2FACP74W1PX. FORD CROWN VICTORIA 1993 problem was reported in MARIETTA, OH. Original Owner. Vehicle was purchased on 19980301. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL TYPE: GAS.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #898941

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 15, 2001.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . SPEED CONTROL WILL NOT DESENGAGE UPON TAPPING ON BRAKES. CONSUMER HAS CONTACTED DEALER. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W9PX. FORD CROWN VICTORIA 1993 problem was reported in BROOKSVILLE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #756634

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 21, 2001.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:ANTILOCK . NO SUMMARY LISTED FOR ABOVER VEHICLE. *AK.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FALP74W5PX. FORD CROWN VICTORIA 1993 problem was reported in VINELAND, NJ. Vehicle was purchased on 20010501. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 75 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #761428

FORD CROWN VICTORIA 1993 car safety problem was reported on Mar 31, 2002.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . WHILE THE VEHICLE WAS IN PARK, WITH NO KEYS IN THE IGNITION, A SMALL CHILD GRABBED THE GEAR SHIFTER. WITH ONLY SLIGHT PRESSURE, THE VEHICLE SLIPPED OUT OF GEAR AND ROLLED BACKWARDS DOWN A HILL, WEDGING A 16 YEAR OLD FEMALE IN THE REAR DRIVER'S SIDE DOOR, THEN PINNING THE FEMALE BETWEEN TWO VEHICLES. THE FEMALE WAS PRONOUNCED DEAD AT A LOCAL HOSPITAL SEVERAL HOURS LATER, AS A RESULT OF THE INJURIES RECEIVED FROM THE VEHICLE.*JB.Vehicle was involved in a crash. 1 person(s) died.Vehicle Identification Number (VIN):2FACP71W3PX. FORD CROWN VICTORIA 1993 problem was reported in INDEPENDENCE, MO. Accident was reported to Police. Original Owner. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. FORD CROWN VICTORIA 1993 drive type:FWD. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #8015881

FORD CROWN VICTORIA 1993 car safety problem was reported on Dec 01, 2001.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:IGNITION:SWITCH . VEHICLE WOULD START INTERMITTENTLY,AND SPARKS WOULD BE SEEN WHEN SWITCHING ON. DEALER CONTACTED. FEEL FREE TO PROVIDE ANY FURTHER INFORMATION. *AK.Vehicle Identification Number (VIN):2FALP74W8PX. FORD CROWN VICTORIA 1993 problem was reported in ATHENS, TN. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #770039

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with OTHER . NO SUMMARY. DT.Vehicle Identification Number (VIN):2FALP74W8PX. FORD CROWN VICTORIA 1993 problem was reported in GAITHERSBURG, MD. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10004424

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY . THE CONSUMER PURCHASED AN OLD POLICE VEHICLE WHICH HAS BEEN RECALLED TO PROVIDE A SAFETY SHIELD AROUND THE FUEL TANK. THE VEHICLE WAS TAKEN TO A DEALER WHO INFORMED THE CONSUMER THAT ONLY ACTIVE POLICE OFFICERS WERE GOING TO RECEIVE THE SHIELD. THE CONSUMER FEELS THE SHIELD SHOULD BE INSTALLED ON ALL RECALL VEHICLES NOT JUST THE ACTIVE POLICE VEHICLE. *NLM.Vehicle Identification Number (VIN):2FALP71W5PX. FORD CROWN VICTORIA 1993 problem was reported in NEW BRAUNFELS, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10008356

FORD CROWN VICTORIA 1993 car safety problem was reported on May 15, 2001.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:MOUNTING . FUEL TANK ASSEMBLY BRACKETS. *JB .Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Mileage was 15 miles. Vehicle Identification Number (VIN):2FACP73W8PX. FORD CROWN VICTORIA 1993 problem was reported in TABERNACLE, NJ. Accident was reported to Police. Original Owner. Vehicle was purchased on 19930110. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph. DEALER'S NAME: HOLMAN . DEALER'S CITY: MT LAUREL . DEALER'S STATE CODE: NJ.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10018601

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 01, 2003.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SEATS . I HAVE HAD TWO FORD CROWN VICS, A 1992 AND NOW A 1993. IN BOTH VEHICLES THE DRIVER'S SIDE SEAT FRAME, ON THE FRONT LEFT CORNER, SHEARED. THIS LEFT THE BOLT STILL ANCHORED TO THE SLIDER FOR THE SEAT ADJUSTER. THE SEATS ROCK BACK AND FORTH. NOT ONLY IS THIS A SAFETY ISSUE, BUT IT MAKE THE SEAT EXTREMELY UNCOMFORTABLE. I DON'T HAVE EXACT DATES AS TO WHEN THIS HAPPENED. THE DATE ON THE FORM IS WRONG AND ONLY SHOWS BECAUSE IT WAS A REQUIRED FIELD. *JB.0 person(s) were injured. 0 person(s) died.FORD CROWN VICTORIA 1993 problem was reported in CAPAC, MI. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10029826

FORD CROWN VICTORIA 1993 car safety problem was reported on July 22, 2003.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with EXTERIOR LIGHTING:HEADLIGHTS:CONCEALMENT DEVICES . THE CONSUMER STATED THE HEADLIGHT LENSES WERE DISCOLORED. *AK *JB.Mileage was 90000 miles. Vehicle Identification Number (VIN):2FACP74WXPX. FORD CROWN VICTORIA 1993 problem was reported in WESTLAND, MI. Vehicle was purchased on 19950501. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10048230

FORD CROWN VICTORIA 1993 car safety problem was reported on Nov 17, 2003.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STEERING:LINKAGES:TIE ROD ASSEMBLY . WHILE DRIVING FRONT PASSENGER SIDE TIE ROD SNAPPED. CONSUMER LOST STEERING CONTROL. CONSUMER MANAGED TO PULL OVER, AND HAD VEHICLE TOWED TO DEALERSHIP. *AK.Mileage was 123000 miles. Vehicle Identification Number (VIN):2FALP74W7PX. FORD CROWN VICTORIA 1993 problem was reported in RADCLIFF, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10059755

FORD CROWN VICTORIA 1993 car safety problem was reported on .FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL:ACCELERATOR PEDAL . THROTTLE STUCK IN REVERSE. AS A RESULT, DRIVER LOST CONTROL OF VEHICLE AND HIT A HOUSE. VEHICLE CAME TO A STOP AFTER CRASHING INTO A BRICK WALL. *AK.Vehicle was involved in a crash. Mileage was 94000 miles. Vehicle Identification Number (VIN):2FACP74W4PX. FORD CROWN VICTORIA 1993 problem was reported in FREMONT, CA. Accident was reported to Police. Vehicle was purchased on 19951001. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10075024

FORD CROWN VICTORIA 1993 car safety problem was reported on June 06, 2004.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT . ON JUNE 6, 2004 WHILE DRIVING AT APPROXIMATELY 35 MPH THE PASSENGER SIDE FRONT END DROPPED DOWN AND SCRAPED THE PAVEMENT, THE STEERING WHEEL JUMPED AROUND AND THE RIGHT FRONT TIRE BLEW. LOOKING UNDER THE CAR REVEALED THAT THE LOWER CONTROL ARM BALL JOINT HAD SEPARATED AND PULLED FREE FROM THE CONTROL ARM. THE LOWER CONTROL ARM HAD BEEN FORCED INTO THE SIDEWALL OF THE TIRE AND GOUGED A HUGE HOLE IN IT. HAD THIS HAPPENED AT HIGHWAY SPEEDS IT COULD HAVE BEEN CATASTROPHIC WITH LOSS OF CONTROL OF THE VEHICLE. THE EXPOSED BALL JOINT END WAS DRY (NO LUBRICANT) AND I COULD SEE GALLING ON THE UPPER TOP HALF OF THE "BALL". THESE ARE SEALED BALL JOINTS THAT HAVE NO GREASE FITTING AND THUS NO PROVISION FOR LUBRICATION. THE CAR HAD TO BE TOWED. IT IS SITTING IN MY DRIVEWAY AT THIS TIME AVAILABLE FOR INSPECTION BY ANYONE. I LOOKED UP RECALLS ON THE INTERNET AND FOUND NHTSA RECALL HISTORY LISTING "1992-99: BEARING WITHIN LOWER BALL JOINT CAN WEAKEN SLOWLY DURING USE AND EVENTUALLY CRACK; COULD RESULT IN SEPARATION, ALLOWING CONTROL ARM TO DROP TO THE GROUND" AND ELSEWHERE RECALL NO. 1998251 REFERS TO CROWN VICTORIA " BEARING LOADS CAN LEAD TO THINNING AND EVENTUAL CRACKING OF THE LOWER CONTROL ARM BALL JOINT" . I ALSO FOUND NHTSA RECORDS OF BALL JOINT FAILURES UNDER THE ODI ID NUMBERS OF: 835503, 713546, 505865, 700771, 714657, 710815. I ALSO FOUND AT ALLDATA.COM UNDER AUTOMOTIVE RECALLS A TSB NO. 98S37 OF DEC. '98 "RECALL - FRONT LOWER CONTROL ARM BALL JOINT REPLACEMENT". I CALLED FORD ON JUNE 8, 2004 AND TALKED TO A REP NAMED NORMAN (I.D. NO. 2357) AND CASE REFERENCE NO. [XXX] AND HE TOLD ME THAT MY CAR [XXX] HAD NO RECALL NOTICES AND THEREFORE IT'S NOT A PROBLEM. I TOLD HIM THAT THIS DEFECTIVE VEHICLE SITUATION COULD CAUSE A FATAL VEHICLE ACCIDENT AND ASKED TO TALK TO HIS SUPERVISOR. HE TOLD ME THAT THERE WASN'T A SUPERIOR I COULD TAKE THE MATTER UP WITH. *AK UPDATED 07/25/2012 *JS INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).Mileage was 170421 miles. Vehicle Identification Number (VIN):2FACP73W6PX. FORD CROWN VICTORIA 1993 problem was reported in OLATHE, KS. Vehicle was purchased on 20010812. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 35 mph. DEALER'S NAME: OLATHE FORD . DEALER'S CITY: OLATHE . DEALER'S STATE CODE: KS. DEALER'S ZIPCODE: 66061 .
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10083533

FORD CROWN VICTORIA 1993 car safety problem was reported on July 22, 2004.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE:BODY:HOOD:HINGE AND ATTACHMENTS . WHEN DRIVING AT AN UNDETERMINED SPEED HOOD OPENED. THIS CAUSED CONSUMER TO PULL OFF THE ROAD. CONSUMER WAS ABLE TO TIE DOWN THE HOOD AND DROVE THE VEHICLE HOME. *AK *SC.Mileage was 68000 miles. Vehicle Identification Number (VIN):2FALP74W9X1. FORD CROWN VICTORIA 1993 problem was reported in WHITESTONE, NY. Vehicle was purchased on 19950823. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. DEALER'S NAME: SATURN OF STATEN ISLAND . DEALER'S TELEPHONE NUMBER: 718-979-8900 . DEALER'S CITY: NY . DEALER'S STATE CODE: NY.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10106620

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 02, 2005.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with EQUIPMENT:MECHANICAL:JACKS . CONSUMER JACKED THE VEHICLE UP TO CHANGE THE OIL. WHILE CHANGING THE OIL THE JACK BROKE, AND THE VEHICLE CAME DOWN. THE JACK SHREDDED IN THE GROVES. *AK THE CONSUMER BEGAN LOWERING THE JACK. ONE TURN OF THE SCREW AND THE JACK FAILED. *TC.Mileage was 140000 miles. Vehicle Identification Number (VIN):2FALP74W4PX. FORD CROWN VICTORIA 1993 problem was reported in BURLINGTON, IA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. DEALER'S NAME: SILOTTERNKIRK . DEALER'S TELEPHONE NUMBER: 319-758-5900 . DEALER'S CITY: WEST BURLINGTON . DEALER'S STATE CODE: IA. DEALER'S ZIPCODE: 52655 .
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10118014

FORD CROWN VICTORIA 1993 car safety problem was reported on Sept 14, 2002.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with AIR BAGS:FRONTAL . MY HUSBAND WAS BLINDED BY THE DRIVER AIRBAG ON A 1993 FORD CROWN VICTORIA IN SEPTEMBER 2002. IT WAS A LOW IMPACT SINGLE CAR ACCIDENT AT 8 MPH. THE AIRBAG DID NOT GO OFF IN A TIMELY MANNER AND BLINDED MY HUSBAND INSTANTLY. MY HUSBAND SUFFERED A TEAR IN THE LEFT MUSCLE AND PERMANENTLY LOST THE VISION IN THAT EYE, TORN IRIS ON BOTH EYES, BLOOD CLOTS IN BOTH EYES; CORNEA DAMAGE TO BOTH EYES... THE LIST IS LONG. HE HAS HAD 8 EYE SURGERIES AND WE ARE STILL UNSURE OF HE WILL LOSE THE REST OF WHAT VISION HE HAS IN THE RIGHT EYE. FORD HAS HAD MANY CASES SINCE THEN, BUT WILL STILL NOT RECALL THESE CARS FOR 1992-1996, WHICH INCLUDE THE GRAND MARQUIS. FORD LOST A CASE IN 2000 (HOFFMAN V. FORD) AND ACCORDING TO AUTOMOTIVE NEWS: FORD WAS AWARE OF AIRBAG COMPLAINTS THAT HAD BEEN MADE BY CONSUMERS, BUT FORD SAYS THEY DID NOTHING BECAUSE NO ONE EVER FILED A LAWSUIT. SINCE THEY LOST THE HOFFMAN CASE, FORD STILL HAS NOT RECALLED THE CARS FOR THE DEFECTIVE AIRBAGS. DURING A $1 BILLION COST SAVING BY FORD, THEY CHANGED THE AIRBAG SENSORS FROM 5 TO 3 SENSORS. THIS SAVED FORD $18-25 PER CAR. THIS COST SAVING IS COSTING PEOPLE THEIR LIVES OR THEY ARE BEING BLINDED WHEN THE AIRBAG DOESN'T GO OFF WHEN IT SHOULD. THE 1993 FORD CROWN VIC'S AIRBAG IS RELEASED INTO YOUR FACE AT . WHEN ARE THE CONSUMERS AND JURIES GOING TO BE TOLD THE TRUTH ABOUT THESE AIRBAGS AND THEIR DANGERS. AIRBAGS MAY SAVE LIVES BUT THEY ALSO BURDEN A FAMILY WITH FINANCIAL RUIN, A LIFETIME OF MEDICAL BILLS AND EMOTIONAL DISTRESS AND FORD TAKES NO RESPONSIBILITY FOR THE RESULTS TO US CONSUMERS. WE LOST OUT CASE AGAINST FORD.*AK.Vehicle was involved in a crash. 1 person(s) were injured. 0 person(s) died.Mileage was 48500 miles. Vehicle Identification Number (VIN):2FACP74W5PX. FORD CROWN VICTORIA 1993 problem was reported in KENNESAW, GA. Accident was reported to Police. Vehicle was purchased on 19930128. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 8 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10118976

FORD CROWN VICTORIA 1993 car safety problem was reported on Apr 19, 2005.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS . WHILE DRIVING AT APPROXIMATELY 40 MPH, THE DRIVER APPLIED THE BRAKES AND THE PEDAL WENT TO THE FLOOR, AND HEARD A POPPING SOUND. THE BRAKE LINE RUPTURED AND FLUID HAD LEAKED EVERYWHERE. THE OWNER TOOK THE VEHICLE TO AN INDEPENDENT MECHANIC, AND WAS INFORMED THAT THEY SEE QUITE A BIT OF THESE FORD VEHICLES WITH THE SAME DEFECT. *AK *SC *JB.Mileage was 69000 miles. Vehicle Identification Number (VIN):2FALP74W1PX. FORD CROWN VICTORIA 1993 problem was reported in CHATHAM, MA. Vehicle was purchased on 19950901. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 40 mph. DEALER'S NAME: HADDON LINCOLN MERCURY . DEALER'S CITY: NORWOOD . DEALER'S STATE CODE: MA.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10127354

FORD CROWN VICTORIA 1993 car safety problem was reported on June 26, 2005.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:WIRING:INTERIOR/UNDER DASH . WHILE DRIVING DOWN THE ROAD I NOTICED THE SPEEDOMETER FALLING TO "0" AND BACK UP TO 70 MPH AND THE ODOMETER STOPPED WORKING. I CALLED THE LOCAL FORD DEALERSHIP TO INQUIRE ABOOUT A DEFECT AND THEY TOLD ME I WOULD HAVE TO PAY FOR IT TO BE FIXED. I CHECKED OTHER MECHANICS WHO TOLD ME IT WAS VERY COMMON FOR THIS TO HAPPEN. IF IT IS SO COMMON THEN WHY HAS THERE NOT BEEN A RECALL ON THEIR DEFECTIVE EQUIPMENT..0 person(s) were injured. 0 person(s) died.Mileage was 85549 miles. Vehicle Identification Number (VIN):2FACP73W1PX. FORD CROWN VICTORIA 1993 problem was reported in BRYAN, TX. Vehicle was purchased on 20050624. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10143419

FORD CROWN VICTORIA 1993 car safety problem was reported on Nov 21, 2005.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:ANTILOCK . 1993 FORD CROWN VICTORIA, I'VE OWNED THIS CAR FOR 8 YEARS,THE ABS PUMP AND HCU FAILED, PARTS WHICH ARE SUPPOSE TO BE DURABLE AND ARE VERY EXPENSIVE, I HAVE 114811 MILES ON THIS CAR AND IT IS IN IMMACULATE CONDITION INSIDE AND OUT, I WOULD LIKE TO KNOW IS THIS CAR SAFE TO DRIVE UNTIL REPAIRS ARE MADE,THIS CONDITION WAS DIAGNOSED AND FOUND BY A FORD DEALER. *NM.0 person(s) were injured. 0 person(s) died.Mileage was 114800 miles. Vehicle Identification Number (VIN):2FACP71W6PX. FORD CROWN VICTORIA 1993 problem was reported in MILWAUKEE, WI. Vehicle was purchased on 19950415. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10158415

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 01, 1901.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL:CRUISE CONTROL . 1993 CROWN VICTORIA DEFECTIVE SPEED CONTROL DEACTIVATION SWITCH CAUSED AN UNDER HOOD FIRE. *TS ***NAR*** THE CONSUMER WAS TOLD THAT HIS VEHICLE WAS NOT INCLUDED IN THE RECALL(99S15). *NM.Vehicle was on fire. Vehicle Identification Number (VIN):2FALP74W0PX. FORD CROWN VICTORIA 1993 problem was reported in BROOKFIELD, IL. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10160972

FORD CROWN VICTORIA 1993 car safety problem was reported on June 28, 2006.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS . DT*: THE CONTACT STATED BRAKE FLUID LEAKED OUT OF THE REAR BRAKE LINE CAUSING THE BRAKES TO BECOME INOPERATIVE. WHEN THE BRAKE PEDAL WAS DEPRESSED, THE PEDAL WENT ALL THE WAY TO THE FLOOR. THERE IS AN NHTSA RECALL, # 96I002000, REGARDING THE SERVICE BRAKES, HYDRAULIC: FOUNDATION COMPONENTS: HOSES, LINES/PIPING, AND FITTINGS. THE VIN WAS NOT INCLUDED IN THE RECALL. UPDATED 7/14/2006 - THE HORN PAD BECAME STUCK. THE DEALERTHE LEFT SIDE HORN BUTTON. *NM UPDATED 03/26/07.*JB .Mileage was 107113 miles. Vehicle Identification Number (VIN):2FALP74W6PX. FORD CROWN VICTORIA 1993 problem was reported in RONKONKONA, NY. Vehicle was purchased on 20030101. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. DEALER'S NAME: MCDANIEL FORD . DEALER'S TELEPHONE NUMBER: 516-681-9006 . DEALER'S CITY: HICKSVILLE . DEALER'S STATE CODE: NY. DEALER'S ZIPCODE: 11801 .
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10160972

FORD CROWN VICTORIA 1993 car safety problem was reported on June 28, 2006.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with COMMUNICATIONS:HORN ASSEMBLY . DT*: THE CONTACT STATED BRAKE FLUID LEAKED OUT OF THE REAR BRAKE LINE CAUSING THE BRAKES TO BECOME INOPERATIVE. WHEN THE BRAKE PEDAL WAS DEPRESSED, THE PEDAL WENT ALL THE WAY TO THE FLOOR. THERE IS AN NHTSA RECALL, # 96I002000, REGARDING THE SERVICE BRAKES, HYDRAULIC: FOUNDATION COMPONENTS: HOSES, LINES/PIPING, AND FITTINGS. THE VIN WAS NOT INCLUDED IN THE RECALL. UPDATED 7/14/2006 - THE HORN PAD BECAME STUCK. THE DEALERTHE LEFT SIDE HORN BUTTON. *NM UPDATED 03/26/07.*JB .Mileage was 107113 miles. Vehicle Identification Number (VIN):2FALP74W6PX. FORD CROWN VICTORIA 1993 problem was reported in RONKONKONA, NY. Vehicle was purchased on 20030101. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. DEALER'S NAME: MCDANIEL FORD . DEALER'S TELEPHONE NUMBER: 516-681-9006 . DEALER'S CITY: HICKSVILLE . DEALER'S STATE CODE: NY. DEALER'S ZIPCODE: 11801 .
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10176386

FORD CROWN VICTORIA 1993 car safety problem was reported on Dec 14, 2006.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:WIRING:FRONT UNDERHOOD . TL*- THE CONTACT CALLED REGARDING A FIRE TO HER VEHICLE, WHICH STARTED UNDER THE HOOD OF HER VEHICLE, AT THE TIME OF THE INCIDENT VEHICLE WAS PARKED. THE CONTACT CALLED THE FIRE DEPARTMENT AND THEY PUT OUT THE FIRE. AT THE TIME OF THE INCIDENT CONTACT WASN'T AWARE OF NHTSA CAMPAIGN NUMBER 99V124000. THE CONTACT IS NOT SURE WHERE THE FIRE STARTED BUT, WAS INFORMED BY THE FIRE DEPT. THAT IT WAS AN ELECTRICAL PROBLEM. CONTACT VEHICLE WAS TOTALED BY THE INSURANCE COMPANY AND WANTED TO KNOW IF THERE WAS ANYWAY SHE COULD GET REIMBURSED. THE CONTACT CAN ALSO PROVIDE A FIRE DEPARTMENT REPORT AND PICTURES IF NEEDED..Vehicle was on fire. 0 person(s) were injured. 0 person(s) died.Mileage was 121911 miles. Vehicle Identification Number (VIN):2FACP74W6PX. FORD CROWN VICTORIA 1993 problem was reported in GRANBY, MO. Accident was reported to Police. Vehicle was purchased on 20050701. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10199001

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 04, 2005.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with OTHER . TL*THE CONTACT OWNS A 1993 FORD CROWN VICTORIA. HE STATED THAT HIS VEHICLE BURNED DOWN 3 YEARS AGO. HE DID NOT KNOW THE CAUSE OF THE FIRE. THE CONTACT FELT THE FUSE BOX CAUSED THE FAILURE. THE CURRENT AND FAILURE MILEAGES WERE 80,000. THERE IS A RECALL FOR THE VEHICLE SPEED CONTROL (NHTSA CAMPAIGN ID #07V336000). .Vehicle was on fire. 0 person(s) were injured. 0 person(s) died.Mileage was 80000 miles. Vehicle Identification Number (VIN):2FALP74W4PX. FORD CROWN VICTORIA 1993 problem was reported in SPRINGFIELD, MA. Vehicle was purchased on 19970322. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph. DEALER'S NAME: GREATER SPRINGFIELD .
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10206317

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 18, 2007.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE:BODY:HOOD:HINGE AND ATTACHMENTS . TL*THE CONTACT OWNS A 1993 FORD CROWN VICTORIA. WHILE DRIVING 70 MPH, THE RIVETS FROM THE HOOD LATCH LOOSENED AND THE HOOD FLEW UP AND CRASHED THROUGH THE WINDSHIELD. THE WINDSHIELD SHATTERED AND SPLINTERS OF GLASS STRUCK THE CONTACT'S FACE. THE HOOD ALSO PLACED A DENT IN THE TOP OF THE VEHICLE, WHICH WOULD COST $200 TO REPAIR. SHE WAS ABLE TO PULL THE VEHICLE OFF THE ROAD AND TIED THE HOOD DOWN. SHE DROVE THE VEHICLE TO A BODY SHOP. THE BODY SHOP REPLACED THE WINDSHIELD AND THE HOOD WAS REPLACED WITH A USED HOOD THAT WAS A DIFFERENT COLOR THAN THE VEHICLE. THE REPAIR COST WAS $519. THE HOOD STILL HAS TO BE PAINTED AND THE TOP OF THE VEHICLE NEEDS TO BE REPAIRED. THE CONTACT DOES NOT KNOW THE PRICE OF THE PAINT JOB. NHTSA CAMPAIGN ID NUMBER 97V024000 (LATCHES/LOCKS/ LINKAGES:HOOD:LATCH) WAS REFERENCED; HOWEVER, SHE WAS INFORMED THAT IT ONLY APPLIED TO POLICE VEHICLES AND TAXI CABS. THE CURRENT AND FAILURE MILEAGES WERE 138,000. UPDATED 06/10/08. *LJ.1 person(s) were injured. 0 person(s) died.Mileage was 138000 miles. Vehicle Identification Number (VIN):2FACP73W8PX. FORD CROWN VICTORIA 1993 problem was reported in TOPEKA, KS. Vehicle was purchased on 19930615. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 70 mph. DEALER'S NAME: CAR VALLEY MOTORS . DEALER'S TELEPHONE NUMBER: 785-232-9160 . DEALER'S CITY: TOPEKA . DEALER'S STATE CODE: KS. DEALER'S ZIPCODE: 66607 .
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10206317

FORD CROWN VICTORIA 1993 car safety problem was reported on Oct 18, 2007.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with LATCHES/LOCKS/LINKAGES:HOOD:LATCH . TL*THE CONTACT OWNS A 1993 FORD CROWN VICTORIA. WHILE DRIVING 70 MPH, THE RIVETS FROM THE HOOD LATCH LOOSENED AND THE HOOD FLEW UP AND CRASHED THROUGH THE WINDSHIELD. THE WINDSHIELD SHATTERED AND SPLINTERS OF GLASS STRUCK THE CONTACT'S FACE. THE HOOD ALSO PLACED A DENT IN THE TOP OF THE VEHICLE, WHICH WOULD COST $200 TO REPAIR. SHE WAS ABLE TO PULL THE VEHICLE OFF THE ROAD AND TIED THE HOOD DOWN. SHE DROVE THE VEHICLE TO A BODY SHOP. THE BODY SHOP REPLACED THE WINDSHIELD AND THE HOOD WAS REPLACED WITH A USED HOOD THAT WAS A DIFFERENT COLOR THAN THE VEHICLE. THE REPAIR COST WAS $519. THE HOOD STILL HAS TO BE PAINTED AND THE TOP OF THE VEHICLE NEEDS TO BE REPAIRED. THE CONTACT DOES NOT KNOW THE PRICE OF THE PAINT JOB. NHTSA CAMPAIGN ID NUMBER 97V024000 (LATCHES/LOCKS/ LINKAGES:HOOD:LATCH) WAS REFERENCED; HOWEVER, SHE WAS INFORMED THAT IT ONLY APPLIED TO POLICE VEHICLES AND TAXI CABS. THE CURRENT AND FAILURE MILEAGES WERE 138,000. UPDATED 06/10/08. *LJ.1 person(s) were injured. 0 person(s) died.Mileage was 138000 miles. Vehicle Identification Number (VIN):2FACP73W8PX. FORD CROWN VICTORIA 1993 problem was reported in TOPEKA, KS. Vehicle was purchased on 19930615. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 70 mph. DEALER'S NAME: CAR VALLEY MOTORS . DEALER'S TELEPHONE NUMBER: 785-232-9160 . DEALER'S CITY: TOPEKA . DEALER'S STATE CODE: KS. DEALER'S ZIPCODE: 66607 .
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10206895

FORD CROWN VICTORIA 1993 car safety problem was reported on Sept 06, 2007.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . TL*THE CONTACT OWNS A 1993 FORD CROWN VICTORIA. THE CONTACT RECEIVED A RECALL NOTICE IN SEPTEMBER OF 2007 FOR THE VEHICLE SPEED CRUISE CONTROL SWITCH. A WEEK PRIOR TO RECEIVING THE NOTICE, HE NOTICED A BURNING SMELL AND THE GEARS WOULD STICK WHEN THE VEHICLE WAS PLACED IN PARK. THE DEALER STATED THAT THE WIRING HARNESS MELTED DUE TO THE SWITCH. APPROXIMATELY TWO WEEKS LATER, THE FAILURE RECURRED WHILE DRIVING. IN ORDER TO PARK THE VEHICLE SAFELY, THE CONTACT HAD TO LEAVE THE VEHICLE IN NEUTRAL AND APPLY THE EMERGENCY BRAKE. HOWEVER, THE BURNING SMELL REMAINED. HE HAS NOT YET TAKEN THE VEHICLE BACK TO THE DEALER OR NOTIFIED THE MANUFACTURER. THE SPEED AND RECALL NUMBER WERE UNKNOWN. THE FAILURE MILEAGE WAS 93,000 AND CURRENT MILEAGE WAS 95,000. UPDATED 01/11/08. *LJ THE CONSUMER STATED THE PROBLEM IS THE WIRING ON THE BRAKE LIGHT SWITCH. WHICH ALSO INTERLOCKS THE TRANSMISSION FROM BEING MOVED OUT OF PARK UNLESS THE BRAKE IS DEPRESSED. UPDATED .0 person(s) were injured. 0 person(s) died.Mileage was 93000 miles. Vehicle Identification Number (VIN):2FALP74W3PX. FORD CROWN VICTORIA 1993 problem was reported in PLATSBERG, NY. Vehicle was purchased on 20040105. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. DEALER'S NAME: PRIVATE OWNER .
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10206895

FORD CROWN VICTORIA 1993 car safety problem was reported on Sept 06, 2007.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:WIRING . TL*THE CONTACT OWNS A 1993 FORD CROWN VICTORIA. THE CONTACT RECEIVED A RECALL NOTICE IN SEPTEMBER OF 2007 FOR THE VEHICLE SPEED CRUISE CONTROL SWITCH. A WEEK PRIOR TO RECEIVING THE NOTICE, HE NOTICED A BURNING SMELL AND THE GEARS WOULD STICK WHEN THE VEHICLE WAS PLACED IN PARK. THE DEALER STATED THAT THE WIRING HARNESS MELTED DUE TO THE SWITCH. APPROXIMATELY TWO WEEKS LATER, THE FAILURE RECURRED WHILE DRIVING. IN ORDER TO PARK THE VEHICLE SAFELY, THE CONTACT HAD TO LEAVE THE VEHICLE IN NEUTRAL AND APPLY THE EMERGENCY BRAKE. HOWEVER, THE BURNING SMELL REMAINED. HE HAS NOT YET TAKEN THE VEHICLE BACK TO THE DEALER OR NOTIFIED THE MANUFACTURER. THE SPEED AND RECALL NUMBER WERE UNKNOWN. THE FAILURE MILEAGE WAS 93,000 AND CURRENT MILEAGE WAS 95,000. UPDATED 01/11/08. *LJ THE CONSUMER STATED THE PROBLEM IS THE WIRING ON THE BRAKE LIGHT SWITCH. WHICH ALSO INTERLOCKS THE TRANSMISSION FROM BEING MOVED OUT OF PARK UNLESS THE BRAKE IS DEPRESSED. UPDATED .0 person(s) were injured. 0 person(s) died.Mileage was 93000 miles. Vehicle Identification Number (VIN):2FALP74W3PX. FORD CROWN VICTORIA 1993 problem was reported in PLATSBERG, NY. Vehicle was purchased on 20040105. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. DEALER'S NAME: PRIVATE OWNER .
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10209205

FORD CROWN VICTORIA 1993 car safety problem was reported on Nov 13, 2007.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . I HAVE AN 1993 FORD CROWN VICTORIA THAT HAS MANY RECALLS. I TOOK THE VEHICLE TO HERITAGE FORD (209) 529-5110 TO HAVE THE CRUISE CONTROL DISCONNECTED AS PER AN RECALL NOTICE I RECEIVED. I WAS TOLD THAT THE NEW CRUISE CONTROL WOULD BE CONNECTED IN OCTOBER OR NOVEMBER. I CALLED THE SERVICE MANAGER ON 11/13/2007 TO FIND OUT WHEN I CAN BRING THE VEHICLE TO HAVE THE NEW CRUISE CONTROL CONNECTED. I WAS TOLD THAT IT WON'T BE UNTIL JANUARY OR FEBRUARY UNTIL THIS WILL HAPPEN. MY SITUATION IS THAT AS AN INDEPENDENT INSURANCE ADJUSTER. I AM ON THE ROAD COVERING A LARGE AREA AT TIMES & WITH THE PRICE OF FUEL, I WANT THE CRUISE CONTROL HOOKED UP FOR FUEL SAVINGS! THERE ARE FOUR OTHER RECALLS WITH THE VEHICLE. I WILL CONFRONT THE DEALERSHIP ABOUT THEM AFTER I GET THIS PROBLEM TAKEN CARE OF. THANK YOU CLIFF MILLER *TR.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP73W5PX. FORD CROWN VICTORIA 1993 problem was reported in MODESTO, CA. Vehicle was purchased on 20070715. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 35 mph. DEALER'S NAME: HERITAGE FORD . DEALER'S TELEPHONE NUMBER: 209-343-5157 . DEALER'S CITY: MODESTO . DEALER'S STATE CODE: CA. DEALER'S ZIPCODE: 95350 .
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10213253

FORD CROWN VICTORIA 1993 car safety problem was reported on Sept 01, 2007.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL:CRUISE CONTROL . TL*THE CONTACT OWNS A 1993 FORD CROWN VICTORIA. THE CONTACT RECEIVED A RECALL NOTICE FOR NHTSA CAMPAIGN ID NUMBER 07V336000 (VEHICLE SPEED CONTROL: CRUISE CONTROL). HIS LOCAL DEALER STATED THAT THEY DID NOT HAVE THE PARTS AVAILABLE FOR THE RECALL REPAIR NOR DID THEY HAVE THE PARTS TO DEACTIVATE THE CRUISE CONTROL SWITCH. THE MANUFACTURER HAS NOT BEEN NOTIFIED. THERE HAD BEEN NO FAILURE TO DATE. THE CURRENT MILEAGE WAS 110,000. .0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP73W5PX. FORD CROWN VICTORIA 1993 problem was reported in VINCENTOWN, NJ. Original Owner. Vehicle was purchased on 19931201. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph. DEALER'S NAME: RICE AND HOLMAN FORD .
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10214818

FORD CROWN VICTORIA 1993 car safety problem was reported on Aug 22, 2007.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . TL*THE CONTACT OWNS A 1993 FORD CROWN VICTORIA. THE CONTACT RECEIVED A RECALL NOTICE FOR NHTSA CAMPAIGN ID NUMBER 07V336000 (VEHICLE SPEED CONTROL) AND FORD RECALL NUMBER 05S28 IN AUGUST OF 2007. THE DEACTIVATION SWITCH WAS DISCONNECTED SHORTLY THEREAFTER. HE CALLED FORD MOTOR COMPANY ON SEVERAL OCCASIONS AND THEY STATED THAT THE PART WOULD BE AVAILABLE THE FOURTH QUARTER OF 2007, WHICH WAS THEN CHANGED TO JANUARY OF 2008. CURRENTLY, FORD DOES NOT KNOW WHEN THE PARTS WILL ARRIVE. THERE HAD BEEN NO FAILURE TO DATE. THE CURRENT MILEAGE WAS 115,000. .0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FACP74W4PX. FORD CROWN VICTORIA 1993 problem was reported in GARNER, IA. Original Owner. Vehicle was purchased on 19930303. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph. DEALER'S NAME: DONALDLER FRIENDS FORD . DEALER'S CITY: MASON CITY . DEALER'S STATE CODE: IA.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10217151

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 01, 1901.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . 1993 FORD CROWN VICTORIA WITH A SPEED CONTROL RECALL. CONSUMER STATES THAT THE RECALL WAS RECEIVED IN SEPTEMBER. CONSUMER WAS TOLD THE PARTS WOULD BE IN, IN DECEMBER, THEN JANUARY. YET NO PARTS TO FIX THE PROBLEM. *KB.Vehicle Identification Number (VIN):2FALP74W6PX. FORD CROWN VICTORIA 1993 problem was reported in HACIENDA HEIGHTS, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10219595

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 28, 2008.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT:CONTROL ARM:LOWER ARM . TL*THE CONTACT OWNS A 1993 FORD CROWN VICTORIA. WHILE DRIVING AT AN UNKNOWN SPEED, THE CONTACT NOTICED THAT THE VEHICLE SPORADICALLY VEERED TO THE RIGHT. THE DEALER STATED THAT ALTHOUGH HE WAS EXPERIENCING THE SAME FAILURE AS NOTED IN NHTSA CAMPAIGN ID NUMBER 95V194000 (SUSPENSION:FRONT:CONTROL ARM:UPPER ARM), THE VIN WAS NOT INCLUDED IN THE RECALL AND THEY WOULD NOT REPAIR HIS VEHICLE FOR FREE. THE VEHICLE IS CURRENTLY BEING REPAIRED. THE FAILURE MILEAGE WAS 172,000 AND CURRENT MILEAGE WAS 173,000. .0 person(s) were injured. 0 person(s) died.Mileage was 172000 miles. Vehicle Identification Number (VIN):2FACP71W8PX. FORD CROWN VICTORIA 1993 problem was reported in NOCOA, TX. Vehicle was purchased on 20070228. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. DEALER'S NAME: PRIVATE OWNER .
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10220763

FORD CROWN VICTORIA 1993 car safety problem was reported on Dec 01, 2007.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . TL*THE CONTACT OWNS A 1993 FORD CROWN VICTORIA. THE VEHICLE CAUGHT FIRE AT THE CONTACT'S WORKPLACE. THE MANUFACTURER WAS NOTIFIED AND STATED THAT THE CONTACT WAS RESPONSIBLE FOR THE REPAIR. HE RECENTLY RECEIVED FORD RECALL LETTER NUMBER 05S28 IN MARCH OF 2008 FOR THE VEHICLE SPEED CONTROL. THE VEHICLE HAS NOT BEEN INSPECTED BY A DEALER. THE VEHICLE IS CURRENTLY PARKED AT HIS RESIDENCE. THE CURRENT AND FAILURE MILEAGES WERE 167,000..Vehicle was on fire. 0 person(s) were injured. 0 person(s) died.Mileage was 167000 miles. Vehicle Identification Number (VIN):2FACP71W1PX. FORD CROWN VICTORIA 1993 problem was reported in SWEET HOME, AR. Vehicle was purchased on 20030101. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph. DEALER'S NAME: STATE VEHICLE .
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10223936

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 01, 1901.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . 1993 FORD CROWN VICTORIA WITH SPEED CONTROL RECALL. CONSUMER STATES THAT THE RECALL REPAIR WAS MADE IN FEBRUARY 2008. CONSUMER STATES THAT THE SERVICE WAS EXCELLENT. *KB.Vehicle Identification Number (VIN):2FALP74WXPX. FORD CROWN VICTORIA 1993 problem was reported in WESTBOROUGH, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. DEALER'S NAME: HERB CHAMBER . DEALER'S CITY: WESTBOROUGH . DEALER'S STATE CODE: MA. DEALER'S ZIPCODE: 01581 .
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10223377

FORD CROWN VICTORIA 1993 car safety problem was reported on Apr 04, 2008.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . TL*THE CONTACT OWNS A 1993 FORD CROWN VICTORIA. THE CONTACT STATED THAT SHE HAD BEEN WAITING FOR THE RECALL REPAIR FOR THE CRUISE CONTROL (NHTSA CAMPAIGN ID NUMBERS 07V336000: VEHICLE SPEED CONTROL) OR 08V051000 (VEHICLE SPEED CONTROL:CRUISE CONTROL) FOR A LONG TIME. ON APRIL 4, 2008, THE CONTACT WENT TO THE DEALER TO HAVE THE RECALL PART INSTALLED. AFTER THE REPAIR, SHE REALIZED THAT THE CRUISE CONTROL NO LONGER FUNCTIONED AT ALL. THE DEALER DID NOT PROVIDE MUCH ASSISTANCE. THE CURRENT MILEAGE WAS 154,000 AND FAILURE MILEAGE WAS 152,000. UPDATED 04/28/08. *LJ THE CONSUMER STATED HER MECHANIC WAS ABLE TO GET THE PART AND NOW THE CRUISE CONTROL WORKS. UPDATED .0 person(s) were injured. 0 person(s) died.Mileage was 152000 miles. Vehicle Identification Number (VIN):2FALP74W7PX. FORD CROWN VICTORIA 1993 problem was reported in SANDUSKY, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FORD CROWN VICTORIA 1993 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. FORD CROWN VICTORIA 1993 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph. DEALER'S NAME: DUBBS FORD . DEALER'S CITY: SANDUSKY . DEALER'S STATE CODE: MI.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10226581

FORD CROWN VICTORIA 1993 car safety problem was reported on Apr 02, 2008.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SEATS . DRIVERS SEAT LEANS BACK, POSSIBLE BROKEN FLOOR BOLT LIKE MENTIONED IN NHTSA ACTION NUMBER : PE98041 ON A 1993 FORD CROWN VIC, ALSO KNEW OF THE SAME PROBLEM WITH A 1992 CROWN VIC WHICH I NO LONGER OWN. DID THEY CHANGE THE SEAT BETWEEN 1993 AND 1198 MODELS? IF THEY DID NOT THEN THE RECALL SHOULD CERTAINLY INCLUDE OLDER MODEL CROWN VICS. *TR.0 person(s) were injured. 0 person(s) died.Mileage was 160000 miles. Vehicle Identification Number (VIN):2FALP74W3PX. FORD CROWN VICTORIA 1993 problem was reported in KANSAS CITY, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. VEHICLE SPEED: 20 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10228088

FORD CROWN VICTORIA 1993 car safety problem was reported on May 17, 2008.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with LATCHES/LOCKS/LINKAGES . FORD 1963 CROWN VICTORIA XL DRIVERS SIDE DOOR POPS OPEN WHILE MOVING. *TR.Mileage was 100000 miles. Vehicle Identification Number (VIN):2FALP74W1PX. FORD CROWN VICTORIA 1993 problem was reported in OCEAN SPRINGS, MS. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. VEHICLE SPEED: 50 mph. DEALER'S NAME: ASTRO FORD . DEALER'S CITY: D'IBERVILLE . DEALER'S STATE CODE: MS.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10298478

FORD CROWN VICTORIA 1993 car safety problem was reported on Jan 04, 2010.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL:CRUISE CONTROL . TL*THE CONTACT OWNS A 1993 FORD CROWN VICTORIA. WHILE THE ENGINE WAS ON WITH THE GEAR IN PARK THE CONTACT NOTICED THAT THERE WERE BLUE AND BLACK SMOKE UNDER THE HOOD. MOMENTS LATER THE CONTACT NOTICED THAT A FIRE HAD BEGUN ON THE FRONT END OF THE VEHICLE. THE FIRE DEPARTMENT WAS CALLED TO EXTINGUISH THE FIRE. THE VEHICLE HAS NOT BEEN DIAGNOSED BY THE DEALER. THE CONTACT NOTICED PRIOR THAT FORD RECALL #08V051000, VEHICLE SPEED CONTROL:CRUISE CONTROL HAD ALREADY BEEN SERVICED ON HIS VEHICLE. THE CURRENT AND FAILURE MILEAGES WERE 132905. .Vehicle was on fire. 0 person(s) were injured. Mileage was 132905 miles. Vehicle Identification Number (VIN):2FACP71W1PX. FORD CROWN VICTORIA 1993 problem was reported in FULTON, MS. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10355766

FORD CROWN VICTORIA 1993 car safety problem was reported on Mar 09, 2007.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT:CONTROL ARM:UPPER ARM . TL* THE CONTACT OWNS 1993 FORD CROWN VICTORIA. THE CONTACT STATED WHILE DRIVING 70 MPH THE FRONT DRIVER'S SIDE BALL JOINT BROKE, CAUSING THE LOWER CONTROL ARM TO COLLAPS. THE DRIVER'S SIDE UPPER CONTROL ARM WAS ALSO DAMAGED AS WELL, CAUSING THE CONTACT TO LOSE CONTROL OF THE STEERING ,WHICH ALMOST CAUSED A CRASH. THE CONTACT HAD THE VEHICLE TOWED TO HIS RESIDENCE. THE CONTACT REPAIRED THE FRONT PASSENGER SIDE CONTROL ARM. HE REFERENCED THE RECALL FOR THE SUSPENSION:FRONT:CONTROL ARM:UPPER ARM (95V194000) HOWEVER, HIS VIN WAS NOT INCLUDED IN THE RECALL. THE CONTACT STATED THE MANUFACTURER SHOULD HONOR THE RECALL ON THIS VEHICLE SINCE THIS IS A MANUFACTURER DEFECT. THE FAILURE MILEAGE WAS 150,000. .Mileage was 140000 miles. Vehicle Identification Number (VIN):2FALP74W7PX. FORD CROWN VICTORIA 1993 problem was reported in FORT PIERCE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.
Ask a Question      Report Your Car Problem      Go Top

FORD CROWN VICTORIA 1993 Safety Review #10441664

FORD CROWN VICTORIA 1993 car safety problem was reported on Dec 28, 2011.FORD CROWN VICTORIA 1993, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE:BODY . TL* THE CONTACT OWNS A 1993 FORD CROWN VICTORIA. THE CONTACT WAS DRIVING 65 MPH WHEN THE HOOD LATCH FAILED AND CAUSED THE HOOD TO ABRUPTLY FLY OPEN, OBSCURING THE CONTACT'S VISION OF THE ROADWAY. THE CONTACT PULLED OVER AND CLOSE HIS HOOD. THE VEHICLE WAS TOWED HOME. THE VEHICLE HAD NOT BEEN INSPECTED BY A DEALER NOR REPAIRED. THE MANUFACTURER WAS CONTACTED AND THEY OFFERED NO ASSISTANCE. THE FAILURE AND THE CURRENT MILEAGES WERE APPROXIMATELY 142,000. .Mileage was 142000 miles. Vehicle Identification Number (VIN):2FALP74W1PX. FORD CROWN VICTORIA 1993 problem was reported in GREELEY, CO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.
Ask a Question      Report Your Car Problem      Go Top