Car-and-Safety.com

Ford F250 1998 Service Brakes, Hydraulic Foundation Components Disc

Ford F250 1998 Service Brakes, Hydraulic Foundation Components Disc Review #700817

FORD F250 1998 car safety problem was reported on Nov 20, 1998.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC . have had 4 failures in the rear suspension system. first time, the traction bars were making a horrible metal-metal creaking/grinding noise; traction bars were replaced. second time the entire bracket bolted to the frame came loose, sliding and banging around on the frame; tractions bars, traction bar brackets, and traction bar bolts all replaced. third time air spring (air ride suspension) leaked down and caused the truck to pull to one side (truck was not level; driver's side rear rode very low, passenger side front rode very high); air spring was replaced. fourth time the traction bar (passenger side) broke; service center not open, plan on taking it in tomorrow. rear window seal has been 'fixed' twice, yet continues to leak water into the cab, last time shorting out some aftermarket electronics behind the rear seat. braking at highway speed (50-75) results in a front-end vibration, rotors were turned by the dealer recently due to a front disc brake problem that resulted in the inside pad wearing down to bare metal and much grinding (wear indicators are on the outside pad and were not engaged (squeaking); so they were not indicating pads needed replacement). the other side pads were worn non-parallel to the pad backing (pad was thicker on one edge than the other)..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):1FTPX28L4WK. Ford F250 1998 problem was reported in COLORADO SPRINGS, CO. Original Owner. Vehicle was purchased on Dec 01, 1997. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:4WD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 10 mph.

Ford F250 1998 Visibility Glass, Side/rear

Ford F250 1998 Visibility Glass, Side/rear Review #700817

FORD F250 1998 car safety problem was reported on Nov 20, 1998.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:GLASS, SIDE/REAR . have had 4 failures in the rear suspension system. first time, the traction bars were making a horrible metal-metal creaking/grinding noise; traction bars were replaced. second time the entire bracket bolted to the frame came loose, sliding and banging around on the frame; tractions bars, traction bar brackets, and traction bar bolts all replaced. third time air spring (air ride suspension) leaked down and caused the truck to pull to one side (truck was not level; driver's side rear rode very low, passenger side front rode very high); air spring was replaced. fourth time the traction bar (passenger side) broke; service center not open, plan on taking it in tomorrow. rear window seal has been 'fixed' twice, yet continues to leak water into the cab, last time shorting out some aftermarket electronics behind the rear seat. braking at highway speed (50-75) results in a front-end vibration, rotors were turned by the dealer recently due to a front disc brake problem that resulted in the inside pad wearing down to bare metal and much grinding (wear indicators are on the outside pad and were not engaged (squeaking); so they were not indicating pads needed replacement). the other side pads were worn non-parallel to the pad backing (pad was thicker on one edge than the other)..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):1FTPX28L4WK. Ford F250 1998 problem was reported in COLORADO SPRINGS, CO. Original Owner. Vehicle was purchased on Dec 01, 1997. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:4WD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 10 mph.

Ford F250 1998 Suspension Rear

Ford F250 1998 Suspension Rear Review #700817

FORD F250 1998 car safety problem was reported on Nov 20, 1998.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:REAR . have had 4 failures in the rear suspension system. first time, the traction bars were making a horrible metal-metal creaking/grinding noise; traction bars were replaced. second time the entire bracket bolted to the frame came loose, sliding and banging around on the frame; tractions bars, traction bar brackets, and traction bar bolts all replaced. third time air spring (air ride suspension) leaked down and caused the truck to pull to one side (truck was not level; driver's side rear rode very low, passenger side front rode very high); air spring was replaced. fourth time the traction bar (passenger side) broke; service center not open, plan on taking it in tomorrow. rear window seal has been 'fixed' twice, yet continues to leak water into the cab, last time shorting out some aftermarket electronics behind the rear seat. braking at highway speed (50-75) results in a front-end vibration, rotors were turned by the dealer recently due to a front disc brake problem that resulted in the inside pad wearing down to bare metal and much grinding (wear indicators are on the outside pad and were not engaged (squeaking); so they were not indicating pads needed replacement). the other side pads were worn non-parallel to the pad backing (pad was thicker on one edge than the other)..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):1FTPX28L4WK. Ford F250 1998 problem was reported in COLORADO SPRINGS, CO. Original Owner. Vehicle was purchased on Dec 01, 1997. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:4WD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 10 mph.

Ford F250 1998 Service Brakes, Hydraulic Foundation Components Drum

Ford F250 1998 Service Brakes, Hydraulic Foundation Components Drum Review #833166

FORD F250 1998 car safety problem was reported on May 01, 1998.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DRUM . while driving at any speed and applying the brakes, the right rear brake will lock up, causing vehicle to slide. also drums got very hot. the consumer has had problems with the vehicle 7 to 8 times, and the vehicle has been in the shop four times for the same problem. since the last time that it has been repaired, problem has not reoccurred. *ak.Vehicle Identification Number (VIN):1FTPX28LOWN. Ford F250 1998 problem was reported in LAKE HAVASU, AZ. Vehicle was purchased on June 25, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:4WD. Ford F250 1998 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 35 mph.

Ford F250 1998 Service Brakes, Hydraulic Foundation Components Drum Drum

Ford F250 1998 Service Brakes, Hydraulic Foundation Components Drum Drum Review #833166

FORD F250 1998 car safety problem was reported on May 01, 1998.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DRUM:DRUM . while driving at any speed and applying the brakes, the right rear brake will lock up, causing vehicle to slide. also drums got very hot. the consumer has had problems with the vehicle 7 to 8 times, and the vehicle has been in the shop four times for the same problem. since the last time that it has been repaired, problem has not reoccurred. *ak.Vehicle Identification Number (VIN):1FTPX28LOWN. Ford F250 1998 problem was reported in LAKE HAVASU, AZ. Vehicle was purchased on June 25, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:4WD. Ford F250 1998 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 35 mph.

Ford F250 1998 Suspension Front Springs Torsion Bar

Ford F250 1998 Suspension Front Springs Torsion Bar Review #702333

FORD F250 1998 car safety problem was reported on Jan 14, 1999.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT:SPRINGS:TORSION BAR . both front torsion bars broke while vehicle was setting in the garage. it appears to be related to cold weather stress or the torsions bars were heat treated to hard. did not flex between the cold weather (0 -10 deg) and the warm garage (45 deg.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):1FTPX28L5WK. Ford F250 1998 problem was reported in CLINTON TWP, MI. Original Owner. Vehicle was purchased on Feb 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:4WD. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford F250 1998 Suspension Front Springs Torsion Bar Review #703028

FORD F250 1998 car safety problem was reported on Feb 06, 1999.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT:SPRINGS:TORSION BAR . breakage occurred either while stationary or doing slow speed - not sure when. vehicle was leaning to right when i returned to it 20 minutes after driving it. feel free to call for more information. i see on the web that these torsion bars have been breaking quite frequently on f150s too! *ak.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FTPX28L0WC. Ford F250 1998 problem was reported in CARP ONTARIO CANADA, WY. Original Owner. Vehicle was purchased on Mar 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:4WD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.

Ford F250 1998 Power Train Automatic Transmission

Ford F250 1998 Power Train Automatic Transmission Review #607554

FORD F250 1998 car safety problem was reported on Sept 18, 1998.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . manufacturer installed transmission wiring incorrectly at factory, resulting in short causing other operations to fail. *yc.Vehicle Identification Number (VIN):1FTRX27L3WN. Ford F250 1998 problem was reported in LAGUNA HIL, CA. Original Owner. Vehicle was purchased on May 29, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Ford F250 1998 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. Ford F250 1998 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 7 mph.

Ford F250 1998 Service Brakes, Hydraulic Foundation Components

Ford F250 1998 Service Brakes, Hydraulic Foundation Components Review #838290

FORD F250 1998 car safety problem was reported on Jan 01, 1998.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS . when applying brakes or slowing down vehicle will shutter, causing a safety hazard. dealer cannot determine what is causing the defect. *ak *ml.Vehicle Identification Number (VIN):1FTPX27L2WK. Ford F250 1998 problem was reported in PIEDMONT, OK. Original Owner. Vehicle was purchased on Jan 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:RWD. Ford F250 1998 TRANSMISSION TYPE: AUTO.

Ford F250 1998 Suspension Front

Ford F250 1998 Suspension Front Review #706957

FORD F250 1998 car safety problem was reported on .FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT . front end tires and steering shake constantly and at highway speed it vibrates and shakes so hard over 50 mph it is had to hold on road. tires are wearing due to shaking. vehicle has had new tires, balancing, front end alignment, more than once. *ak.Vehicle Identification Number (VIN):1FTNE24L9WH. Ford F250 1998 problem was reported in ODESSA, FL. Original Owner. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Ford F250 1998 drive type:FWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.

Ford F250 1998 Exterior Lighting Turn Signal Flasher Unit

Ford F250 1998 Exterior Lighting Turn Signal Flasher Unit Review #707734

FORD F250 1998 car safety problem was reported on .FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with EXTERIOR LIGHTING:TURN SIGNAL:FLASHER UNIT . turn signal does not remain engaged or is difficult to engage during turns..Vehicle Identification Number (VIN):1FTPX28L2WK. Ford F250 1998 problem was reported in MT. FREEDOM, NJ. Original Owner. Vehicle was purchased on Mar 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:4WD. FUEL TYPE: GAS.

Ford F250 1998 Service Brakes, Hydraulic Antilock

Ford F250 1998 Service Brakes, Hydraulic Antilock Review #709657

FORD F250 1998 car safety problem was reported on .FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:ANTILOCK . brakes shudder or wobble. multiple repairs done but problem persists. we were given a loaner truck (same model and make) which turned out to have same problem! dealer has replaced all brake parts multiple times , turned drums multiple times, and replac.Vehicle Identification Number (VIN):1FTPX28L1WK. Ford F250 1998 problem was reported in MERIDIAN, ID. Original Owner. Vehicle was purchased on Oct 01, 1997. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:4WD. FUEL TYPE: GAS.

Ford F250 1998 Service Brakes, Hydraulic Antilock Review #845904

FORD F250 1998 car safety problem was reported on .FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:ANTILOCK . when applying the brakes right rear wheel locks up, causing the vehicle to spin. dealer can't find a solution. *ak.Ford F250 1998 problem was reported in BROKEN ARROW, OK. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control.

Ford F250 1998 Power Train Driveline Driveshaft

Ford F250 1998 Power Train Driveline Driveshaft Review #609268

FORD F250 1998 car safety problem was reported on Feb 01, 1999.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:DRIVELINE:DRIVESHAFT . drive shaft making noise. yh.Vehicle Identification Number (VIN):1FTRX27L4WN. Ford F250 1998 problem was reported in ENCINITAS, CA. Original Owner. Vehicle was purchased on July 01, 1998. Vehicle was using Cruise Control.Ford F250 1998 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. Ford F250 1998 TRANSMISSION TYPE: AUTO.

Ford F250 1998 Structure Frame And Members

Ford F250 1998 Structure Frame And Members Review #609268

FORD F250 1998 car safety problem was reported on Feb 01, 1999.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE:FRAME AND MEMBERS . under carrige of vehicle rusted. yh.Vehicle Identification Number (VIN):1FTRX27L4WN. Ford F250 1998 problem was reported in ENCINITAS, CA. Original Owner. Vehicle was purchased on July 01, 1998. Vehicle was using Cruise Control.Ford F250 1998 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. Ford F250 1998 TRANSMISSION TYPE: AUTO.

Ford F250 1998 Visibility Glass, Side/rear

Ford F250 1998 Visibility Glass, Side/rear Review #712952

FORD F250 1998 car safety problem was reported on Dec 20, 1998.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:GLASS, SIDE/REAR . dealer service depart states: "3 out of 10" trucks have this problem! why no recall?.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):1FTPX28L7WN. Ford F250 1998 problem was reported in BOWIE, MD. Original Owner. Vehicle was purchased on Jan 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:4WD. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford F250 1998 Suspension Front Springs Torsion Bar

Ford F250 1998 Suspension Front Springs Torsion Bar Review #607258

FORD F250 1998 car safety problem was reported on Sept 01, 1998.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT:SPRINGS:TORSION BAR . torsion bars failed. yh.Vehicle Identification Number (VIN):1FTPX27L3WN. Ford F250 1998 problem was reported in SPRINGVILL, CA. Original Owner. Vehicle was purchased on Jan 22, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. Ford F250 1998 TRANSMISSION TYPE: AUTO.

Ford F250 1998 Service Brakes, Hydraulic Foundation Components Disc

Ford F250 1998 Service Brakes, Hydraulic Foundation Components Disc Review #720812

FORD F250 1998 car safety problem was reported on Apr 01, 1998.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC . when brakes are applied, brakes lock and release resulting in failure of vehicle to stop. when brakes are applied quickly, pedal goes to floor and brakes fail. when traveling over a bumpy surface, if brakes are applied, they fail. if driving on extremely wet roads and brakes are applied, they fail to work properly. brakes pads and/or rotors have been replaced numerous times due to improper wear. numerous attempts have been made with the dealer and ford motor company to resolve. however, since warranty has expired, ford motor company refuses to discuss vehicle replacement. they acknowledge a braking defect however they claim to have no solution at this time. copies of all repair orders and service notices from ford are available, as well as correspondence to the dispute reolution board and ford motor company. *ak.Vehicle Identification Number (VIN):1FTRX2761WN. Ford F250 1998 problem was reported in ASHLAND, KY. Original Owner. Vehicle was purchased on Sept 01, 1997. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Ford F250 1998 Service Brakes, Hydraulic Antilock

Ford F250 1998 Service Brakes, Hydraulic Antilock Review #720812

FORD F250 1998 car safety problem was reported on Apr 01, 1998.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:ANTILOCK . when brakes are applied, brakes lock and release resulting in failure of vehicle to stop. when brakes are applied quickly, pedal goes to floor and brakes fail. when traveling over a bumpy surface, if brakes are applied, they fail. if driving on extremely wet roads and brakes are applied, they fail to work properly. brakes pads and/or rotors have been replaced numerous times due to improper wear. numerous attempts have been made with the dealer and ford motor company to resolve. however, since warranty has expired, ford motor company refuses to discuss vehicle replacement. they acknowledge a braking defect however they claim to have no solution at this time. copies of all repair orders and service notices from ford are available, as well as correspondence to the dispute reolution board and ford motor company. *ak.Vehicle Identification Number (VIN):1FTRX2761WN. Ford F250 1998 problem was reported in ASHLAND, KY. Original Owner. Vehicle was purchased on Sept 01, 1997. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Ford F250 1998 Air Bags Frontal

Ford F250 1998 Air Bags Frontal Review #722178

FORD F250 1998 car safety problem was reported on Sept 01, 1999.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with AIR BAGS:FRONTAL . one side of truck sat low, shortly after the other side sat low. rear end airbag suspension gave way as well as the springs. air bags were replaced twice with in 3 month period. after recieving truck from repair shop it was noticed by body shop that frame on left side was cracked. this crack was in front view of service people and not detected. i do not recall the crack from the previous time the air bags were replaced. i do not recall the crack when i dropped the truck for second replacement of airbags and springs. the truck frame on left side is held together by two inches of connecting steel and i have been advised not to drive the vehicle. this truck is my livelyhood and only means of transportation. ford body shop will not weld or repair frame do to liability. they recommend new frame. after discussion with service people and body shop manager it was revealed that ford made changes to the frame in the 1999 year. this is why in the 1998 f-250 a disiel engine was not available. other words the 1998 f-250 was found to be a weaker frame than any other year. also, the design of the airbag suspension system of this truck is weaker than even the f-150 models. the springs are of lessor materials and lessor strength. this was explained to me that this was done do to the airbags capability to make up the difference is support. my view is that all these components work in unisonand when one system failed the others followed. the repairs i have done are not remedying the problem and i have paid $ 2000.00 and much lost time. there is a defect in the frame and ford needs to correct this problem. .*ak.Vehicle Identification Number (VIN):1FTRX2769WN. Ford F250 1998 problem was reported in HOMESTEAD, FL. Original Owner. Vehicle was purchased on Feb 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.

Ford F250 1998 Suspension Rear Springs Leaf Spring Assembly

Ford F250 1998 Suspension Rear Springs Leaf Spring Assembly Review #722178

FORD F250 1998 car safety problem was reported on Sept 01, 1999.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:REAR:SPRINGS:LEAF SPRING ASSEMBLY . one side of truck sat low, shortly after the other side sat low. rear end airbag suspension gave way as well as the springs. air bags were replaced twice with in 3 month period. after recieving truck from repair shop it was noticed by body shop that frame on left side was cracked. this crack was in front view of service people and not detected. i do not recall the crack from the previous time the air bags were replaced. i do not recall the crack when i dropped the truck for second replacement of airbags and springs. the truck frame on left side is held together by two inches of connecting steel and i have been advised not to drive the vehicle. this truck is my livelyhood and only means of transportation. ford body shop will not weld or repair frame do to liability. they recommend new frame. after discussion with service people and body shop manager it was revealed that ford made changes to the frame in the 1999 year. this is why in the 1998 f-250 a disiel engine was not available. other words the 1998 f-250 was found to be a weaker frame than any other year. also, the design of the airbag suspension system of this truck is weaker than even the f-150 models. the springs are of lessor materials and lessor strength. this was explained to me that this was done do to the airbags capability to make up the difference is support. my view is that all these components work in unisonand when one system failed the others followed. the repairs i have done are not remedying the problem and i have paid $ 2000.00 and much lost time. there is a defect in the frame and ford needs to correct this problem. .*ak.Vehicle Identification Number (VIN):1FTRX2769WN. Ford F250 1998 problem was reported in HOMESTEAD, FL. Original Owner. Vehicle was purchased on Feb 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.

Ford F250 1998 Structure Frame And Members

Ford F250 1998 Structure Frame And Members Review #722178

FORD F250 1998 car safety problem was reported on Sept 01, 1999.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE:FRAME AND MEMBERS . one side of truck sat low, shortly after the other side sat low. rear end airbag suspension gave way as well as the springs. air bags were replaced twice with in 3 month period. after recieving truck from repair shop it was noticed by body shop that frame on left side was cracked. this crack was in front view of service people and not detected. i do not recall the crack from the previous time the air bags were replaced. i do not recall the crack when i dropped the truck for second replacement of airbags and springs. the truck frame on left side is held together by two inches of connecting steel and i have been advised not to drive the vehicle. this truck is my livelyhood and only means of transportation. ford body shop will not weld or repair frame do to liability. they recommend new frame. after discussion with service people and body shop manager it was revealed that ford made changes to the frame in the 1999 year. this is why in the 1998 f-250 a disiel engine was not available. other words the 1998 f-250 was found to be a weaker frame than any other year. also, the design of the airbag suspension system of this truck is weaker than even the f-150 models. the springs are of lessor materials and lessor strength. this was explained to me that this was done do to the airbags capability to make up the difference is support. my view is that all these components work in unisonand when one system failed the others followed. the repairs i have done are not remedying the problem and i have paid $ 2000.00 and much lost time. there is a defect in the frame and ford needs to correct this problem. .*ak.Vehicle Identification Number (VIN):1FTRX2769WN. Ford F250 1998 problem was reported in HOMESTEAD, FL. Original Owner. Vehicle was purchased on Feb 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.

Ford F250 1998 Air Bags

Ford F250 1998 Air Bags Review #729010

FORD F250 1998 car safety problem was reported on Aug 22, 2000.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with AIR BAGS . during a front impact collision with another vehicle above 15 mph the air bags failed to deploy . i am in doubt as to the reliability of the system. the dealer said it did not deploy due to the angle at which the bumper was hit..Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):1FTPX28L1WN. Ford F250 1998 problem was reported in CALLAWAY, MD. Accident was reported to Police. Original Owner. Vehicle was purchased on Aug 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:4WD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford F250 1998 Suspension Front Springs Torsion Bar

Ford F250 1998 Suspension Front Springs Torsion Bar Review #874158

FORD F250 1998 car safety problem was reported on Oct 27, 2000.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT:SPRINGS:TORSION BAR . torsion bar keeps braking first on driver's side at 35000 which could cause front end to drop, then on passenger's side.*ak torsion bar broke twice in the same year. front end dropping at high speed could cause the vehicle to rollover. *yh.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):1FTDY28L4WK. Ford F250 1998 problem was reported in WENDOVER, UT. Vehicle was purchased on Jan 01, 1999. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Ford F250 1998 drive type:4WD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. Ford F250 1998 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph.

Ford F250 1998 Fuel System, Other Storage

Ford F250 1998 Fuel System, Other Storage Review #876436

FORD F250 1998 car safety problem was reported on Dec 13, 1998.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, OTHER:STORAGE . truck that was purchased brand new has a lpg tank assembly, consumer smells propane through the fresh air of the a/c system while set on vent, floor, and defrost, dealership has not been able to remedy the problem after many attempts. *slc .0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):1FTPX28Z8WK. Ford F250 1998 problem was reported in MURPHY, TX. Original Owner. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:4WD. Ford F250 1998 TRANSMISSION TYPE: AUTO.

Ford F250 1998 Suspension Front Springs Torsion Bar

Ford F250 1998 Suspension Front Springs Torsion Bar Review #878143

FORD F250 1998 car safety problem was reported on Jan 12, 2001.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT:SPRINGS:TORSION BAR . while driving torsion bar broke which almost cause a crash. currently at dealer. *ak the manufacturer fixed the torsion bar. *yh.Vehicle Identification Number (VIN):1FTPXZ8L6WK. Ford F250 1998 problem was reported in HARRISONVILLE, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Ford F250 1998 drive type:4WD. FUEL TYPE: GAS. Ford F250 1998 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 55 mph.

Ford F250 1998 Service Brakes, Hydraulic Foundation Components Disc Rotor

Ford F250 1998 Service Brakes, Hydraulic Foundation Components Disc Rotor Review #878475

FORD F250 1998 car safety problem was reported on Jan 18, 2000.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:ROTOR . abs system does not work properly when vehicle comes to a sudden stop. this usually happens at 30-40 mph. contacted dealer, and dealer rotated rotors.*ak.Vehicle Identification Number (VIN):2FTPX28W3WC. Ford F250 1998 problem was reported in FRESNOE, CA. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control.

Ford F250 1998 Service Brakes, Hydraulic Antilock

Ford F250 1998 Service Brakes, Hydraulic Antilock Review #878475

FORD F250 1998 car safety problem was reported on Jan 18, 2000.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:ANTILOCK . abs system does not work properly when vehicle comes to a sudden stop. this usually happens at 30-40 mph. contacted dealer, and dealer rotated rotors.*ak.Vehicle Identification Number (VIN):2FTPX28W3WC. Ford F250 1998 problem was reported in FRESNOE, CA. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control.

Ford F250 1998 Vehicle Speed Control Accelerator Pedal

Ford F250 1998 Vehicle Speed Control Accelerator Pedal Review #878902

FORD F250 1998 car safety problem was reported on .FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL:ACCELERATOR PEDAL . when weather is cold throttle gets stuck in open position, causing vehicle to respond as if cruise contol was activated. ford has been contacted.*ak.Vehicle Identification Number (VIN):2FTPF28L8WC. Ford F250 1998 problem was reported in BRADFORD, PA. Original Owner. Vehicle was purchased on June 11, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:4WD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. Ford F250 1998 TRANSMISSION TYPE: AUTO.

Ford F250 1998 Structure Frame And Members

Ford F250 1998 Structure Frame And Members Review #558987

FORD F250 1998 car safety problem was reported on .FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE:FRAME AND MEMBERS . vehicle experiences a problem with the frame continually becoming warped even after being replaced, the consumer is concerned that it could break while driving. *slc.Vehicle Identification Number (VIN):1FTRX2769WN. Ford F250 1998 problem was reported in HOMESTEAD, FL. Vehicle was using Cruise Control.Ford F250 1998 drive type:RWD. FUEL SYSTEM:N/A. Ford F250 1998 TRANSMISSION TYPE: AUTO.

Ford F250 1998 Structure Frame And Members Review #559157

FORD F250 1998 car safety problem was reported on .FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE:FRAME AND MEMBERS . the 6 month old frame is warped, there was a break on the frame that was visible when the repairs were made, the dealer stated that the suspension broke, consumer states that the problem is still persisting. *slc.Vehicle Identification Number (VIN):1FTRX2769WN. Ford F250 1998 problem was reported in HOMESTEAD, FL. Vehicle was using Cruise Control.Ford F250 1998 drive type:RWD. FUEL SYSTEM:N/A. Ford F250 1998 TRANSMISSION TYPE: AUTO.

Ford F250 1998 Structure Body Door

Ford F250 1998 Structure Body Door Review #884757

FORD F250 1998 car safety problem was reported on Jan 01, 2001.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE:BODY:DOOR . driver's side door is cracking above door handle. dealership is replacing door. *ak.Vehicle Identification Number (VIN):1FTPX28LXWK. Ford F250 1998 problem was reported in BULINGTON, KS. Original Owner. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.

Ford F250 1998 Service Brakes, Hydraulic Antilock

Ford F250 1998 Service Brakes, Hydraulic Antilock Review #744515

FORD F250 1998 car safety problem was reported on Oct 09, 2000.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:ANTILOCK . no summary listed for above vehicle. *ak.Vehicle Identification Number (VIN):1FTPF28W7WK. Ford F250 1998 problem was reported in DUNLAP, IL. Original Owner. Vehicle was purchased on Sept 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Ford F250 1998 drive type:4WD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.

Ford F250 1998 Engine And Engine Cooling Engine Gasoline

Ford F250 1998 Engine And Engine Cooling Engine Gasoline Review #744514

FORD F250 1998 car safety problem was reported on July 07, 2000.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE:GASOLINE . no summary listed for abov evehicle. *ak.Vehicle Identification Number (VIN):1FTPF28W0WK. Ford F250 1998 problem was reported in DUNLAP, IL. Original Owner. Vehicle was purchased on Sept 01, 1999. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Ford F250 1998 drive type:4WD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 50 mph.

Ford F250 1998 Suspension Front

Ford F250 1998 Suspension Front Review #744515

FORD F250 1998 car safety problem was reported on Oct 09, 2000.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT . no summary listed for above vehicle. *ak.Vehicle Identification Number (VIN):1FTPF28W7WK. Ford F250 1998 problem was reported in DUNLAP, IL. Original Owner. Vehicle was purchased on Sept 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Ford F250 1998 drive type:4WD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.

Ford F250 1998 Engine And Engine Cooling Engine Gasoline

Ford F250 1998 Engine And Engine Cooling Engine Gasoline Review #744515

FORD F250 1998 car safety problem was reported on Oct 09, 2000.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE:GASOLINE . no summary listed for above vehicle. *ak.Vehicle Identification Number (VIN):1FTPF28W7WK. Ford F250 1998 problem was reported in DUNLAP, IL. Original Owner. Vehicle was purchased on Sept 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Ford F250 1998 drive type:4WD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.

Ford F250 1998 Service Brakes, Hydraulic Antilock

Ford F250 1998 Service Brakes, Hydraulic Antilock Review #744520

FORD F250 1998 car safety problem was reported on Dec 20, 1999.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:ANTILOCK . no summary listed for abov evehicle. *ak.Vehicle Identification Number (VIN):1FTRF2768WK. Ford F250 1998 problem was reported in DUNLAP, IL. Original Owner. Vehicle was purchased on Sept 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Ford F250 1998 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.

Ford F250 1998 Suspension Front

Ford F250 1998 Suspension Front Review #744514

FORD F250 1998 car safety problem was reported on July 07, 2000.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT . no summary listed for abov evehicle. *ak.Vehicle Identification Number (VIN):1FTPF28W0WK. Ford F250 1998 problem was reported in DUNLAP, IL. Original Owner. Vehicle was purchased on Sept 01, 1999. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Ford F250 1998 drive type:4WD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 50 mph.

Ford F250 1998 Service Brakes, Hydraulic Antilock

Ford F250 1998 Service Brakes, Hydraulic Antilock Review #744514

FORD F250 1998 car safety problem was reported on July 07, 2000.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC:ANTILOCK . no summary listed for abov evehicle. *ak.Vehicle Identification Number (VIN):1FTPF28W0WK. Ford F250 1998 problem was reported in DUNLAP, IL. Original Owner. Vehicle was purchased on Sept 01, 1999. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Ford F250 1998 drive type:4WD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 50 mph.

Ford F250 1998 Steering Hydraulic Power Assist System

Ford F250 1998 Steering Hydraulic Power Assist System Review #744520

FORD F250 1998 car safety problem was reported on Dec 20, 1999.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with STEERING:HYDRAULIC POWER ASSIST SYSTEM . no summary listed for abov evehicle. *ak.Vehicle Identification Number (VIN):1FTRF2768WK. Ford F250 1998 problem was reported in DUNLAP, IL. Original Owner. Vehicle was purchased on Sept 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Ford F250 1998 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.

Ford F250 1998 Structure Body

Ford F250 1998 Structure Body Review #744987

FORD F250 1998 car safety problem was reported on Mar 03, 1999.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE:BODY . water leaking to interior of vehicle caused mal-functions causing truck to short and stop in intersection.*ak.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):1FTPF28L6WK. Ford F250 1998 problem was reported in SANTA CRUZ, CA. Original Owner. Vehicle was purchased on Aug 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Ford F250 1998 drive type:4WD. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph.

Ford F250 1998 Engine And Engine Cooling Engine

Ford F250 1998 Engine And Engine Cooling Engine Review #891434

FORD F250 1998 car safety problem was reported on Apr 18, 2001.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE . spark plug number four had blown out of head, consumer managed to get vehicle to a mechanice and was informed that head was made of aluminum and engine was made of iron, this is what caused the spark plugs to blow, right head was replaced for a total cost of $1900, partial reimbursement ws given to consumer. *slc.Vehicle Identification Number (VIN):1FTPX28L0WN. Ford F250 1998 problem was reported in WEARE, NJ. Original Owner. Vehicle was purchased on Mar 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FUEL SYSTEM:N/A. FUEL TYPE: GAS. Ford F250 1998 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 40 mph.

Ford F250 1998 Electrical System Ignition

Ford F250 1998 Electrical System Ignition Review #891434

FORD F250 1998 car safety problem was reported on Apr 18, 2001.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:IGNITION . spark plug number four had blown out of head, consumer managed to get vehicle to a mechanice and was informed that head was made of aluminum and engine was made of iron, this is what caused the spark plugs to blow, right head was replaced for a total cost of $1900, partial reimbursement ws given to consumer. *slc.Vehicle Identification Number (VIN):1FTPX28L0WN. Ford F250 1998 problem was reported in WEARE, NJ. Original Owner. Vehicle was purchased on Mar 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.FUEL SYSTEM:N/A. FUEL TYPE: GAS. Ford F250 1998 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 40 mph.

Ford F250 1998 Vehicle Speed Control

Ford F250 1998 Vehicle Speed Control Review #752795

FORD F250 1998 car safety problem was reported on Sept 29, 2001.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . while traveling down interstate with cruise on at 70mph, the cruisew ould not turn off with the brake being applied or with the off button, the cruise accelerated and would not turn off until the key was used to turn the motor off with out locking the steering wheel. the first two times this happen it was just that the cruise would not turn off with the brake or off button.*ak.Ford F250 1998 problem was reported in NEW PARIS, OH. Original Owner. Vehicle was purchased on Apr 01, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:RWD. FUEL TYPE: GAS. VEHICLE SPEED: 70 mph.

Ford F250 1998 Structure Body Door

Ford F250 1998 Structure Body Door Review #757308

FORD F250 1998 car safety problem was reported on .FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE:BODY:DOOR . both doors of vehicle exhibit a fatigue crack on the outside of the vehicle near the window area, rear edge, about 3 inches up from the bottom of window frame, crack begins at the rubber weather seal, then progresses rearward horizontally for about ,5 inches. we then checked my buddies 1997 f150 and his had it too. he then check 3 of his friends, and they also had the cracks. seems that auto body shops know of this problem, check it out seems to be a high percentage from a very small sample. *ak.Ford F250 1998 problem was reported in NASHVILLE ILLINOIS, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Ford F250 1998 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.

Ford F250 1998 Structure Body Door Review #758242

FORD F250 1998 car safety problem was reported on .FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE:BODY:DOOR . have found a crack located on the driver's side door at window cutout.*ak.Vehicle Identification Number (VIN):2FTPX28L8WC. Ford F250 1998 problem was reported in STANWOOD, WA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Ford F250 1998 drive type:FWD. FUEL TYPE: GAS.

Ford F250 1998 Engine And Engine Cooling Engine Gasoline

Ford F250 1998 Engine And Engine Cooling Engine Gasoline Review #785884

FORD F250 1998 car safety problem was reported on Dec 30, 2001.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE:GASOLINE . while driving the vehicle the oil light came on, discovered vehicle was low on oil and replaced oil, next day vehicle made a terrible noise and was taken to dealer only to find the oil had been burned up through the converter.engine is bad due to the casings. *jg .Vehicle Identification Number (VIN):1FTPX27L2WN. Ford F250 1998 problem was reported in HIRAM, OH. Vehicle was purchased on Aug 30, 2000. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.

Ford F250 1998 Engine And Engine Cooling Engine Gasoline Review #785884

FORD F250 1998 car safety problem was reported on Dec 30, 2001.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE:GASOLINE . while driving the vehicle the oil light came on, discovered vehicle was low on oil and replaced oil, next day vehicle made a terrible noise and was taken to dealer only to find the oil had been burned up through the converter.engine is bad due to the casings. *jg .Vehicle Identification Number (VIN):1FTPX27L2WN. Ford F250 1998 problem was reported in HIRAM, OH. Vehicle was purchased on Aug 30, 2000. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Ford F250 1998 drive type:RWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS.

Ford F250 1998 Air Bags Frontal

Ford F250 1998 Air Bags Frontal Review #8012630

FORD F250 1998 car safety problem was reported on June 23, 2002.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with AIR BAGS:FRONTAL . while driving at 35mph involved in a frontal collison. upon impact, air bags did not deploy.*ak.Vehicle was involved in a crash. Vehicle Identification Number (VIN):2FTPX2861WC. Ford F250 1998 problem was reported in ELK CITY, ID. Original Owner. Vehicle was not using Cruise Control.

Ford F250 1998 Suspension Rear Springs Air Suspension System

Ford F250 1998 Suspension Rear Springs Air Suspension System Review #10017031

FORD F250 1998 car safety problem was reported on May 03, 2003.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:REAR:SPRINGS:AIR SUSPENSION SYSTEM . i have a 1998 f-250 light duty pickup with rear air bag suspension. the air bags have failed 3 times in the last 18 months. i was hoping there was a recall or something from ford to fix this problem, i am getting tired of replacing these things at $500 a piece. *jb.Mileage was 114500 miles. Vehicle Identification Number (VIN):1FTPX28LXWN. Ford F250 1998 problem was reported in CRYSTAL RIVER, FL. Vehicle was purchased on Feb 23, 1999. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. Ford F250 1998 drive type:4WD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford F250 1998 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph.

Ford F250 1998 Service Brakes, Hydraulic

Ford F250 1998 Service Brakes, Hydraulic Review #10025079

FORD F250 1998 car safety problem was reported on .FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC . there was a pulsation in the brake pedal when depressed. the abs system locked up intermittently which caused the tires to wear prematurely. *nlm.Mileage was 9000 miles. Vehicle Identification Number (VIN):2FTPX28W3WC. Ford F250 1998 problem was reported in FRESNO, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford F250 1998 Exterior Lighting Turn Signal

Ford F250 1998 Exterior Lighting Turn Signal Review #10034352

FORD F250 1998 car safety problem was reported on Aug 22, 2003.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with EXTERIOR LIGHTING:TURN SIGNAL . right turn signals would fail to stay on if road bears opposite of signal. independent technician replaced turn signal. but, problem was not solved, unable to be fixed. dealer stated need to replace the switch. it will cost consumer $310.00. *ak.Ford F250 1998 problem was reported in FORT COLLINS, CO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford F250 1998 Suspension Rear Springs Air Suspension System Springs/bags

Ford F250 1998 Suspension Rear Springs Air Suspension System Springs/bags Review #10047999

FORD F250 1998 car safety problem was reported on Nov 10, 2003.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:REAR:SPRINGS:AIR SUSPENSION SYSTEM:SPRINGS/BAGS . while driving, the rear suspension snapped. the consumer managed to pull over and had the vehicle towed. the dealership tried to repair the problem once before, but the problem was not resolved. *ak three air suspension bags had blown out since the consumer purchased the vehicle. (right airbag on the rear suspension) *scc *jb.Mileage was 115738 miles. Vehicle Identification Number (VIN):1FTPX27L2WN. Ford F250 1998 problem was reported in PLAISTOW, NH. Original Owner. Vehicle was purchased on June 29, 1998. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. Ford F250 1998 TRANSMISSION TYPE: AUTO. DEALER'S NAME: REGAN FORD . DEALER'S TELEPHONE NUMBER: 978 373 3878 . DEALER'S CITY: HAVERHILL . DEALER'S STATE CODE: MA. DEALER'S ZIPCODE: 01830 .

Ford F250 1998 Electrical System Starter Assembly

Ford F250 1998 Electrical System Starter Assembly Review #10082335

FORD F250 1998 car safety problem was reported on July 12, 2004.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM:STARTER ASSEMBLY . while starting my ford truck with the 5.4 l engine i heard a very loud pop and the engine ran as if the head gasket blew. a non-ford mechanic verified the no. 3 spark plug on the passenger side blew out and stripped the threads from the cylinder head insert that this ford dealer inserted to repair an earlier blown spark plug. the old insert for the previous failure was removed and replaced with a new type according to the ford mechanic. this is the second time for this to happen. on july 10, 2003, approximately 1 yr and 2 days before this failure the no. 3 spark plug blew out stripping the treads in the cylinder head. numerous non-ford mechanics i've talked to have verified this been a fairly common occurrence in the 5.4 l ford engine in trucks and suv's. an individual that i work with had the same spark plug (no. 3 passenger side) blow out from her ford explorer with the 5.4 l engine approximately 6 weeks ago. *la.0 person(s) were injured. 0 person(s) died.Mileage was 35890 miles. Vehicle Identification Number (VIN):2FTPX28L4WC. Ford F250 1998 problem was reported in ANCHORAGE, AK. Original Owner. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. Ford F250 1998 drive type:4WD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford F250 1998 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph. DEALER'S NAME: CAL WORTHINGTON FORD .

Ford F250 1998 Engine And Engine Cooling Engine

Ford F250 1998 Engine And Engine Cooling Engine Review #10082335

FORD F250 1998 car safety problem was reported on July 12, 2004.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING:ENGINE . while starting my ford truck with the 5.4 l engine i heard a very loud pop and the engine ran as if the head gasket blew. a non-ford mechanic verified the no. 3 spark plug on the passenger side blew out and stripped the threads from the cylinder head insert that this ford dealer inserted to repair an earlier blown spark plug. the old insert for the previous failure was removed and replaced with a new type according to the ford mechanic. this is the second time for this to happen. on july 10, 2003, approximately 1 yr and 2 days before this failure the no. 3 spark plug blew out stripping the treads in the cylinder head. numerous non-ford mechanics i've talked to have verified this been a fairly common occurrence in the 5.4 l ford engine in trucks and suv's. an individual that i work with had the same spark plug (no. 3 passenger side) blow out from her ford explorer with the 5.4 l engine approximately 6 weeks ago. *la.0 person(s) were injured. 0 person(s) died.Mileage was 35890 miles. Vehicle Identification Number (VIN):2FTPX28L4WC. Ford F250 1998 problem was reported in ANCHORAGE, AK. Original Owner. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. Ford F250 1998 drive type:4WD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford F250 1998 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph. DEALER'S NAME: CAL WORTHINGTON FORD .

Ford F250 1998 Engine And Engine Cooling Review #10099084

FORD F250 1998 car safety problem was reported on Aug 28, 2004.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . the truck was started and the spark plug blew out from the engine. the truck was taken to a local dealership. they stated it wasn't a problem. the next time, the spark plug blew out while traveling on the highway at 55 mph. the consumer had to coast to the side of the road. please provide details. *jb.Mileage was 59500 miles. Vehicle Identification Number (VIN):FILL IN. Ford F250 1998 problem was reported in PORTAGE, WI. Original Owner. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Ford F250 1998 TRANSMISSION TYPE: AUTO.

Ford F250 1998 Suspension Front Springs Torsion Bar

Ford F250 1998 Suspension Front Springs Torsion Bar Review #10116154

FORD F250 1998 car safety problem was reported on Mar 28, 2005.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT:SPRINGS:TORSION BAR . broken front torsion bar. started motor, shifted from park to reverse, and without moving from the spot, heard a loud crack and the torsion bar had snapped. my garage was told by their parts supplier that, until this past month, they never had a request for this part before. this is now the second request in the past month. kept the broken bar after replacement..0 person(s) were injured. 0 person(s) died.Mileage was 55000 miles. Vehicle Identification Number (VIN):1FTPF28L3WN. Ford F250 1998 problem was reported in REINHOLDS, PA. Vehicle was purchased on Aug 03, 2002. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. Ford F250 1998 drive type:4WD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford F250 1998 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph.

Ford F250 1998 Steering

Ford F250 1998 Steering Review #10245531

FORD F250 1998 car safety problem was reported on Oct 14, 2008.FORD F250 1998, manufactured by FORD MOTOR COMPANY had a problem with STEERING . steering gear box. it has become disengaged at the pitman arm. and leaking fluid. i have found that the 97 and 99 versions of this truck have had problems and recalls for this. i was told a while back ( about 1 year ago) by a car dealership owner that this truck is actually a 99 i would like to add my vehicle year to this list. i have also had problems with the spark plugs "popping out" which is also a problem with the triton engines. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 190000 miles. Vehicle Identification Number (VIN):1FTPX28L2WN. Ford F250 1998 problem was reported in PEPPERELL, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 15 mph.

Air Bags 1 Review(s)

Air Bags Frontal 2 Review(s)

Electrical System Ignition 1 Review(s)

Electrical System Starter Assembly 1 Review(s)

Engine And Engine Cooling 1 Review(s)

Engine And Engine Cooling Engine 2 Review(s)

Engine And Engine Cooling Engine Gasoline 4 Review(s)

Exterior Lighting Turn Signal 1 Review(s)

Exterior Lighting Turn Signal Flasher Unit 1 Review(s)

Fuel System, Other Storage 1 Review(s)

Power Train Automatic Transmission 1 Review(s)

Power Train Driveline Driveshaft 1 Review(s)

Service Brakes, Hydraulic 1 Review(s)

Service Brakes, Hydraulic Antilock 7 Review(s)

Service Brakes, Hydraulic Foundation Components 1 Review(s)

Service Brakes, Hydraulic Foundation Components Disc 2 Review(s)

Service Brakes, Hydraulic Foundation Components Disc Rotor 1 Review(s)

Service Brakes, Hydraulic Foundation Components Drum 1 Review(s)

Service Brakes, Hydraulic Foundation Components Drum Drum 1 Review(s)

Steering 1 Review(s)

Steering Hydraulic Power Assist System 1 Review(s)

Structure Body 1 Review(s)

Structure Body Door 3 Review(s)

Structure Frame And Members 4 Review(s)

Suspension Front 3 Review(s)

Suspension Front Springs Torsion Bar 6 Review(s)

Suspension Rear 1 Review(s)

Suspension Rear Springs Air Suspension System 1 Review(s)

Suspension Rear Springs Air Suspension System Springs/bags 1 Review(s)

Suspension Rear Springs Leaf Spring Assembly 1 Review(s)

Vehicle Speed Control 1 Review(s)

Vehicle Speed Control Accelerator Pedal 1 Review(s)

Visibility Glass, Side/rear 2 Review(s)