Car-and-Safety.com

Plymouth B200 1990 Safety Reports and Reviews



Plymouth B200 Reports


PLYMOUTH B200 Service Brakes, Hydraulic Foundation Components

PLYMOUTH B200 1990 Service Brakes, Hydraulic Foundation Components Report #973436

PLYMOUTH B200 1990 car safety problem was reported on Oct 17, 1993.PLYMOUTH B200 1990, manufactured by DAIMLERCHRYSLER CORPORATION had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS . BRAKE SYSTEM FAILURE, BRAKE PEDAL FEELS SPONGY WHEN BRAKING, ALSO PEDAL GOES TO FLOOR. TT CONSUMER OVERHAULED BRAKE SYSTEM AND EVER SINCE THEN THE FOLLOWING HAS BEEN DONE: MASTER CYLINDER HAS BEEN REPLACED 8 TIMES, 4 BRAKE BOOSTERS HAVE BEEN REPLACED, ONE PROPORTIONAL VALVE REPLACED, 3 SETS OF REAR BRAKE SHOES AND WHEEL CYLINDERS, 1 SET OF ABOVE DRUMS, 1 PAIR OF NEW ROTORS ON FRONT AND ONE TURNING OF THESE NEW PARTS, 1 PAIR NEW FRONT BRAKE HOSES, AND APPROXIMATELY 7 TO 9 REBUILT FRONT CALIPERS AND PADS. *SLC.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):BB2BF5X1438. Plymouth B200 1990 problem was reported in SPRINGFIELD, OR. Vehicle was using Cruise Control.Plymouth B200 1990 drive type:RWD. FUEL TYPE: GAS. Plymouth B200 1990 TRANSMISSION TYPE: AUTO.
     Report Your Car Problem      Go Top

PLYMOUTH B200 Service Brakes, Hydraulic Power Assist Hydraulic

PLYMOUTH B200 1990 Service Brakes, Hydraulic Power Assist Hydraulic Report #973436

PLYMOUTH B200 1990 car safety problem was reported on Oct 17, 1993.PLYMOUTH B200 1990, manufactured by DAIMLERCHRYSLER CORPORATION had a problem with SERVICE BRAKES, HYDRAULIC:POWER ASSIST:HYDRAULIC . BRAKE SYSTEM FAILURE, BRAKE PEDAL FEELS SPONGY WHEN BRAKING, ALSO PEDAL GOES TO FLOOR. TT CONSUMER OVERHAULED BRAKE SYSTEM AND EVER SINCE THEN THE FOLLOWING HAS BEEN DONE: MASTER CYLINDER HAS BEEN REPLACED 8 TIMES, 4 BRAKE BOOSTERS HAVE BEEN REPLACED, ONE PROPORTIONAL VALVE REPLACED, 3 SETS OF REAR BRAKE SHOES AND WHEEL CYLINDERS, 1 SET OF ABOVE DRUMS, 1 PAIR OF NEW ROTORS ON FRONT AND ONE TURNING OF THESE NEW PARTS, 1 PAIR NEW FRONT BRAKE HOSES, AND APPROXIMATELY 7 TO 9 REBUILT FRONT CALIPERS AND PADS. *SLC.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):BB2BF5X1438. Plymouth B200 1990 problem was reported in SPRINGFIELD, OR. Vehicle was using Cruise Control.Plymouth B200 1990 drive type:RWD. FUEL TYPE: GAS. Plymouth B200 1990 TRANSMISSION TYPE: AUTO.
     Report Your Car Problem      Go Top

Plymouth B200 1990 systems


Share, Email, Print



Rate PLYMOUTH B200 1990 Reliability


Excellent
Good
OK
Bad
Terrible

View Results

Do you enjoy driving your car?


Great, love it!
Yes, a very good ride
It is OK...
No, Don't like it
Definitely Not, Terrible

View Results

You might be interested in the following information from our sponsors



Plymouth B200 1990 Reviews


how do i fix the water pump with out taking everything apart

I have a 1991 Plymouth Grand Voyager. Recently I've noticed that the steering wheel sometimes shakes while I'm driving....not severe, but it's very disconcerting. Also, I am hearing noise from the front passenger side. I checked the tire pressu

1999 plymouht voyager  3.3 at remplace the rack and pinnion  and front strut and noise coking comming over time

what does it mean when the car still turns on but wont move in any gear and also rolls in park?

where is the speed sensor on a plymouth aclame

where on the 1998 plymouth voyager se would i find the rear defrost wiring.

transmission is controlled by electric servos, not line pressure. Servo package may be bad (silver box on trans case) or your fluid is low, or your transmission filter is clogged. Filter and fluid are under 20 bucks. Servo pack is much more. 

You cannot bleed brakes through an ABS system. You have to get it professionally done with the proper tools. 

The spark is controlled by 2 sensors, crank and camshaft. Either not working will cause a no spark situation. The camshaft sensor is the main sensor, but if the crank sensor doesnt "see" crankshaft rotation, it assumes the car has been turned off

You dont. The pump is under the pulley cover on both 4 and 6 motors, and the cover is around the motor mount. You also need to remove the crank hub to get the cover off, and that involves a crankshaft pulley puller, removing the inner fenderwell o

While driving my 1999 plymouth breeze the car went into low gear and the speedmetor stop working

95 grand voyager in limp mode...replaced input and output speed sensors, correct fluid, still in limp mode. Please help!!


Discuss PLYMOUTH B200 1990


No comments have been provided.


Plymouth B200 1990 Recalls


Plymouth B200 1990 Service Bulletins

PLYMOUTH B200 1990