Car-and-Safety.com

Mazda Mazdaspeed3 2010 Safety Reports and Reviews



Mazda Mazdaspeed3 2010 Reviews



Mazda Mazdaspeed3 2010 Seats

Mazda Mazdaspeed3 2010 Seats Review #10481035

MAZDA MAZDASPEED3 2010 car safety problem was reported on Sept 05, 2012.MAZDA MAZDASPEED3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . tl* the contact owns a 2010 mazda mazdaspeed3. the contact stated that the driver's seat fractured from one side of the frame rail. the vehicle was taken to the dealer who stated that the seat frame was fractured and needed to be replaced. the manufacturer was made aware of the failure who offered to cover partial repair expenses. the vehicle was not repaired. the failure mileage was 40,000 and the current mileage was 51,835. .0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Vehicle Identification Number (VIN):JM1BL1H3XA1. Mazda Mazdaspeed3 2010 problem was reported in HOUSTON, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazdaspeed3 2010 Seats Review #10560150

MAZDA MAZDASPEED3 2010 car safety problem was reported on Jan 10, 2014.MAZDA MAZDASPEED3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . driving when seat made a loud popping sound and began rocking wildly. upon investigation realized the weld had broken. there is a tsb that applies to my vin number, but mazda wants $700 to repair the seat. there are a lot of online complaints about this very issue. shouldn't this be a recall as it is a major safety issue. if i had been driving faster i would have crashed. tsb #09-049/10 "2010 mazda3 - rattle noise from bottom of driver seat" applies to vins lower than [xxx] information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6). *tr.0 person(s) were injured. 0 person(s) died.Mileage was 61300 miles. Vehicle Identification Number (VIN):JM1BL1H32A1. Mazda Mazdaspeed3 2010 problem was reported in PFLUGERVILLE, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 10 mph.

Mazda Mazdaspeed3 2010 Tires

Mazda Mazdaspeed3 2010 Tires Review #10565306

MAZDA MAZDASPEED3 2010 car safety problem was reported on Feb 18, 2014.MAZDA MAZDASPEED3 2010, manufactured by Mazda Motor Corp. had a problem with TIRES . this has happened more than just the date listed here. the tire pressure sensors (tps) on this and other vehicles are prone to corrosion and failure. this is because the exterior stem is aluminum and the interior core is another metal (nickel-plated, perhaps) and the entire sensor body is energized. when the tps is exposed to road salt and snowmelt, the aluminum corrodes and can break off, causing an uncontrolled deflation of the tire. this happened to me and my wife on two occasions while changing a tire and i have heard of other instances in which drivers have experienced catastrophic failure of the tps and tire deflation at highway speeds. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 84000 miles. Mazda Mazdaspeed3 2010 problem was reported in FALMOUTH, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazdaspeed3 2010 Wheels

Mazda Mazdaspeed3 2010 Wheels Review #10565306

MAZDA MAZDASPEED3 2010 car safety problem was reported on Feb 18, 2014.MAZDA MAZDASPEED3 2010, manufactured by Mazda Motor Corp. had a problem with WHEELS . this has happened more than just the date listed here. the tire pressure sensors (tps) on this and other vehicles are prone to corrosion and failure. this is because the exterior stem is aluminum and the interior core is another metal (nickel-plated, perhaps) and the entire sensor body is energized. when the tps is exposed to road salt and snowmelt, the aluminum corrodes and can break off, causing an uncontrolled deflation of the tire. this happened to me and my wife on two occasions while changing a tire and i have heard of other instances in which drivers have experienced catastrophic failure of the tps and tire deflation at highway speeds. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 84000 miles. Mazda Mazdaspeed3 2010 problem was reported in FALMOUTH, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazdaspeed3 2010 Seats

Mazda Mazdaspeed3 2010 Seats Review #10594854

MAZDA MAZDASPEED3 2010 car safety problem was reported on May 23, 2014.MAZDA MAZDASPEED3 2010, manufactured by Mazda Motor Corp. had a problem with SEATS . we were driving on a highway when the seat bracket that holds the driver's seat to the position adjustment frame snapped, causing the seat to tip backwards. a collision was narrowly avoided. in the event of an accident the seat would not have been likely to stay connected to the car. the part in question is a 1/4" or 3/8" steel bracket that appears to have broken near a factory weld. pictures are available. the dealer performed an investigation, but concluded that they did not know why it had happened and have never seen something like this before. there appears to be a pattern of this establishing on the nhtsa database and anecdotally on automobile enthusiast websites. there was no early indication of a pending failure. we are concerned the same may happen with the passenger seat or again to the drivers seat after repair. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 125000 miles. Vehicle Identification Number (VIN):JM1BL1H39A1. Mazda Mazdaspeed3 2010 problem was reported in WEST DES MOINES, IA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Mazda Mazdaspeed3 2010 Structure

Mazda Mazdaspeed3 2010 Structure Review #10598130

MAZDA MAZDASPEED3 2010 car safety problem was reported on June 01, 2013.MAZDA MAZDASPEED3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE . the entire dashboard of my 2010 mazda3 is melting! the majority of it has melted into a thick tar like substance; the rest of it has become very soft, with a sticky thick glue like texture. i took the car to the mazda dealership and they said they have seen a few of these melting dashboards but i would have to contact mazda & it probably would not be covered. a couple of days ago i noticed that the tar like "pool of goo" has started a slow thick black drip of liquid dashboard streaming towards one of the vents. the glare of my "ebony oasis" on the windshield makes it very difficult & very dangerous when driving. combine the blazing texas sun & houston traffic with that and it's beyond what anyone should have to endure to get to and from work... so i can pay for the car that's literally melting around me! if a manufacturer's vehicle can't take "the (texas) heat" they should stay out of the kitchen... i mean market! *js.0 person(s) were injured. 0 person(s) died.Mileage was 50000 miles. Vehicle Identification Number (VIN):JM1BL1S54A1. Mazda Mazdaspeed3 2010 problem was reported in SPRING, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazdaspeed3 2010 drive type:FWD.

Mazda Mazdaspeed3 2010 Unknown Or Other

Mazda Mazdaspeed3 2010 Unknown Or Other Review #10619188

MAZDA MAZDASPEED3 2010 car safety problem was reported on July 28, 2014.MAZDA MAZDASPEED3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . dashboard is melting. has sticky residue all over dashboard. during day the glare makes it hard to drive..0 person(s) were injured. 0 person(s) died.Mileage was 80000 miles. Vehicle Identification Number (VIN):JM1BL1U72D1. Mazda Mazdaspeed3 2010 problem was reported in CHANNELVIEW, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazdaspeed3 2010 Visibility/wiper

Mazda Mazdaspeed3 2010 Visibility/wiper Review #10653443

MAZDA MAZDASPEED3 2010 car safety problem was reported on Nov 21, 2013.MAZDA MAZDASPEED3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . the dashboard of the vehicle has been melting and causing a glare while driving..0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Vehicle Identification Number (VIN):JM1BL1SF0A1. Mazda Mazdaspeed3 2010 problem was reported in WEST PALM BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazdaspeed3 2010 Seats

Mazda Mazdaspeed3 2010 Seats Review #10662068

MAZDA MAZDASPEED3 2010 car safety problem was reported on Dec 01, 2014.MAZDA MAZDASPEED3 2010, manufactured by Mazda Motor Corp. had a problem with SEATS . i was taking a clover-leaf off-ramp when i heard a snap (or pop) and felt my seat rock back about 3 inches with more inches to go back. i took my 2010 mazdaspeed 3 into morrie's minnetonka mazda in order for them to inspect the part that had broken. the washer came loose from the bottom of the driver side seat rail on the left side. the mechanics had reattached the washer, which appeared to be a pressed-on washer, and when testing the seat by rocking in it, the washer fell off again. the recommendation that the dealership had given me was to purchase a new driver seat rail assembly, which costs $1080.00 + tax/ss. i had declined to purchase this part, as i don't believe the seat rail assembly is worth that amount, plus i could have purchased a nice set of aftermarket seats like brands bride or sparco. after posting to a facebook group page called "mazda community blog", many other members have posted similar experiences, and have provided many references to other websites that have close to the same issue that i have experienced. it appears to be mostly related to the 2010 mazdaspeed 3 / 2010 mazda 3 years of when this issue has had occurrences. some other similar issues that others have also had are the welds breaking on the seats, which have a similar effect to what my seat felt like..0 person(s) were injured. 0 person(s) died.Mileage was 46296 miles. Vehicle Identification Number (VIN):JM1BL1H37A1. Mazda Mazdaspeed3 2010 problem was reported in NEW RICHMOND, WI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Mazda Mazdaspeed3 2010 Seats Review #10662092

MAZDA MAZDASPEED3 2010 car safety problem was reported on May 14, 2014.MAZDA MAZDASPEED3 2010, manufactured by Mazda Motor Corp. had a problem with SEATS . while i was entering the freeway i felt the seat moved back i almost got into accident when it happen luckily it didnt happen. i went to a mazda dealership and asked them about the seat they said its not covered by the warranty i have to pay 800 plus labor to fix the seat. the second time it happen i was at the stop light and when the light turn green the seat moved way back and i couldnt reach the gas and the clutch pedal so i stalled in the middle of the street and there was traffic coming, almost got into accident again. so now i have to hold the steering wheel and move closer to the streering wheel just to reach the gas ,brake, and clutch pedal and thats not the proper way to seat for the drivers if anyone got into accident that close to the air they might suffocate if the air deploy during an accident. please fix this problem i dont want this to happen this to anyone. i have pictures to prove it..0 person(s) were injured. 0 person(s) died.Mileage was 66257 miles. Vehicle Identification Number (VIN):JM1BL1H41A1. Mazda Mazdaspeed3 2010 problem was reported in VALLEJO, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.


Mazda Mazdaspeed3 2010 Systems


Seats 5 Review(s)

Structure 1 Review(s)

Tires 1 Review(s)

Unknown Or Other 1 Review(s)

Visibility/wiper 1 Review(s)

Wheels 1 Review(s)



Search 1000s of Car Reviews, Recalls and Technical Bulletins
Start by entering a car model, system, manufacturer or any combination of keywords.


Mazda Mazdaspeed3 2010 Reports


My 2001 626 transmission slips slightly when first put it into drive from park then bucks. After it engages it shifts fine

I have a 1998 Mazda Protege LX Touring Edition (4dr) and need to install a rear-facing infant car seat (with base) in the back seat, preferably center position.  Because I purchased my Mazda used, I do not have the Owner's Manual.  I was told th

question is whiseling noise when take off

Sorry the question is for Tribute 2010 for whiseling noise when taking off

Today I backed up in a narrow parking lot and as I put my 2009 Mazda 6 in drive and with my foot still on the brake the car accelrated unexpectedly over about 10 feet and into a building, the engine revving and smoking as I put it in neutral and t

mazda3 2007 radio fuse location

my alt light came on and stayed so i disconnected the battery to see if the car would sat running and now both headlaights burnt out the tach is in op no and the air bag lamp stays on all the time what happened?

94 mazda 626 air bag ligt stays on after alt burnt out what is the problem

I REALLY THINK I HAVE THE ANSWER, I HOPE.  I have an 2002 Mazda tribute it stalls especially in hot weather.  The manual says very little, but it said it may be a vapor lock.  My car was parked inside a humid garage so when it stalls on me seas

Another really difficult thing to diagnose was the engine light, and warning bell sounding off for a yr. the dealer ship misdiagnosed the problem.  Charged me for a diagnostic test they did not do.  They sold me a battery, and sent me down the r

I can't find my Satellitte Radio Number, it appeared originally on my NAV Screen when I would depress the SAT button. It no longer appears. I don't know if that's a malfunction.
I have a 2008 Mazda CX-9 Grand touring with the Navigation touch s

 i have a 2002 millenia , would a 1998 automtic transmission work for car, denny.koch@insightbb.com

Discuss Mazda Mazdaspeed3


No comments have been provided.


Mazda Mazdaspeed3 2010 Recalls


Mazda Mazdaspeed3 2010 Service Bulletins


Mazda Mazdaspeed3 2010