Car-and-Safety.com

Mazda Mazda6 2010 Tires

Mazda Mazda6 2010 Tires Review #10346731

MAZDA MAZDA6 2010 car safety problem was reported on Aug 01, 2010.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . tl* the contact owns a 2010 mazda 6. the contact stated while traveling at 20 mph, the rear passenger tire split. the tires were examined 3,000 miles ago and the contact was told that the vehicle was safe. the vehicle was not taken to the dealer for diagnosis. the dot number was not available. the failure and current mileage was 8,000. .Mileage was 8000 miles. Vehicle Identification Number (VIN):1YVHZ8BH1A5. Mazda Mazda6 2010 problem was reported in BRIDGPORT, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 20 mph.

Mazda Mazda6 2010 Tires Pressure Monitoring And Regulating Systems

Mazda Mazda6 2010 Tires Pressure Monitoring And Regulating Systems Review #10392918

MAZDA MAZDA6 2010 car safety problem was reported on Mar 25, 2011.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS . tpms valve broke when checking air pressure in the tire. tire went flat and tpms had to be replaced. *tr.Vehicle Identification Number (VIN):1YVHZ8BH7A5. Mazda Mazda6 2010 problem was reported in SAN JOSE, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda6 2010 Electrical System

Mazda Mazda6 2010 Electrical System Review #10393113

MAZDA MAZDA6 2010 car safety problem was reported on Mar 28, 2011.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with ELECTRICAL SYSTEM . tl* the contact owns a 2010 mazda mazda6. the contact was driving 2 mph and entering a residential driveway when the start/stop button was inadvertently engaged and the steering wheel locked. the contact stated that the start/stop button was located below the air conditioner button and the contact believed the location of the button was a safety hazard. the vin was not available. the approximate failure mileage was 25,000..Mileage was 25000 miles. Mazda Mazda6 2010 problem was reported in ALBUQUERQUE, NM. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 2 mph.

Mazda Mazda6 2010 Service Brakes, Hydraulic

Mazda Mazda6 2010 Service Brakes, Hydraulic Review #10399901

MAZDA MAZDA6 2010 car safety problem was reported on Apr 01, 2011.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with SERVICE BRAKES, HYDRAULIC . my 2010 mazda 6 which has less than 10,000 miles on it has been reported by the service center that all 4 rotors are out of round and need to be replaced. however, the brakes and brake pads are fine. the warranty will not cover the replacement of the rotors. another issue is when i turn the steering wheel to the right the horn will randomly start beeping. the service center stated it did not happen for them. *tr.Mileage was 9700 miles. Vehicle Identification Number (VIN):1YVHZ8BH6A5. Mazda Mazda6 2010 problem was reported in STATEN ISLAND, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS.

Mazda Mazda6 2010 Exterior Lighting

Mazda Mazda6 2010 Exterior Lighting Review #10402409

MAZDA MAZDA6 2010 car safety problem was reported on Mar 15, 2011.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with EXTERIOR LIGHTING . the inner tail light lenses on both the driver & passenger side of my 2010 mazda 6 touring are physically melting and becoming severely deformed. the outer, clear lenses are not damaged and the melting is originating in the vicinity of the bulbs. car has not been altered from the mfg and bulbs are manufacturer recommended. car has 48,000 miles on it and beyond the 36,000 mfg warranty therefore mazda will not replace them for free. i believe this is a supplier, design or manufacturing defect that can possibly cause a fire or reduced brake light visibility and this part should not melt. i have pictures and can send them as reference. a search of the internet showed a few other incidents with defective mazda tail lights on other models and years similar to this. i am uncertain how wide spread this situation is. pictures received. updated 06/14/11 *tr.Mileage was 46000 miles. Vehicle Identification Number (VIN):1YVHZ8CH7A5. Mazda Mazda6 2010 problem was reported in ROANOKE, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda6 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda6 2010 Electrical System

Mazda Mazda6 2010 Electrical System Review #10409451

MAZDA MAZDA6 2010 car safety problem was reported on June 15, 2011.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with ELECTRICAL SYSTEM . i was driving on the freeway after leaving class. after being on the freeway for about 5 minutes, the car starts to power down. all of the caution lights start to come on (ie: battery light, traction light, oil light and many others). as i get off the freeway, the car starts to lose more power, the fuel acceleration did not work as well and the steering became very hard because something happened to the power steering fluid. then as i start to pull into a parking lot there is smoke coming from both sides of the closed hood. i put the car in park, turn off the acceleration, and pop the hood and i noticed it is on fire. i ran from car and called the fire department. after all is said and done, the car is totaled. i am not sure what components malfunctioned in the car which insurance is determining at the moment. this is a mazda defect!!!!!.Vehicle was on fire. 0 person(s) were injured. 0 person(s) died.Mileage was 6385 miles. Vehicle Identification Number (VIN):1YVHZ8CH5A5. Mazda Mazda6 2010 problem was reported in WARREN, MI. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Mazda Mazda6 2010 Air Bags Frontal

Mazda Mazda6 2010 Air Bags Frontal Review #10408525

MAZDA MAZDA6 2010 car safety problem was reported on Oct 16, 2010.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with AIR BAGS:FRONTAL . tl* the contact owns a 2010 mazda, mazda6. when the contact started the ignition the front passenger side air bag off indicator illuminated on the instrument panel when an occupant was present in the front passenger seat. the failure occurred sporadically. the vehicle was taken to an authorized dealer who stated the air bag functioned properly. the manufacturer was notified of the problem and assured the contact that the vehicle met the specifications and requirements. the approximate mileage was 300. the vin was unavailable. updated 07/26/11*lj updated 3/22/12 *cn.Mileage was 300 miles. Vehicle Identification Number (VIN):1YVHZ8BH9A5. Mazda Mazda6 2010 problem was reported in KENTWOOD, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. DEALER'S NAME: BORGMAN FORD MAZDA . DEALER'S TELEPHONE NUMBER: 800-968-1888 .

Mazda Mazda6 2010 Structure Body Bumpers

Mazda Mazda6 2010 Structure Body Bumpers Review #10411128

MAZDA MAZDA6 2010 car safety problem was reported on July 01, 2011.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with STRUCTURE:BODY:BUMPERS . this concerns the plastic safety bumper on my mazda and plastic bumpers in general. mine is a safety hazard and in danger of breaking off. i believe it to be a defective product. i have a mazda6 touring plus which is ten months old, with less than 12,000 miles. my bumper began cracking two months ago. the rip went from the top of the bumper to the bottom. in time, the rip has expanded to a fourth of a bumper. i am using shipping tape to hold it in place. shipping tape! the bumper is so brittle, it's useless as a safety bumper. i get no satisfaction from my dealer , ramsey mazda, ramsey n.j .or from mazda headquarters. they tell me the crack may have occurred when i went over a pothole or safety bumper and suggest i ask my insurance company to pay $1300 for the replacement cost. i believe this should be covered by warranty. more important, bumpers of this sort should be banned. they are a safety hazard and should be replaced with a solid bumper or better quality. i have owned many cars over the years and i have never heard of a bumper ripping or flaking. updated 07/05/11 *bf .0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):M6603613000. Mazda Mazda6 2010 problem was reported in PARAMUS, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. DEALER'S NAME: RAMSEY MAZDA .

Mazda Mazda6 2010 Service Brakes, Hydraulic

Mazda Mazda6 2010 Service Brakes, Hydraulic Review #10428087

MAZDA MAZDA6 2010 car safety problem was reported on Sept 21, 2011.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with SERVICE BRAKES, HYDRAULIC . brake sensor making noise as if the brakes need to be replaced. vehicle has under 10000 miles. have owned several new vehicles and have never had to replace the brakes for a new vehicle at this number of mileage. possible defect with mazdas braking system. *tr.Mileage was 9560 miles. Mazda Mazda6 2010 problem was reported in PHILADELPHIA, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda6 2010 Seats

Mazda Mazda6 2010 Seats Review #10429170

MAZDA MAZDA6 2010 car safety problem was reported on Feb 01, 2010.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . leased new 2010 mazda 6 october 2009. about 3 months later, i turned the lumbar adjustment knob, and a loud pop happens and the knob starts freewheeling. the lumbar knob connection (shaft/whatever it is) to the internals broke. many months later, i called to make an appointment at the same time as a recall came out. medical conditions prevented me from keeping that appointment, so i called and canceled it. so today, 10/07/11 i took it in for the recall and the broken lumbar knob connection so that parts could be ordered to fix it. turns out there were 2 other recalls too, so that was added to the list. about 2 1/2 hours later, the car is brought up. the service adviser says that the tech sees there are aftermarket seat covers on the seats, and therefore whoever put those on, broke the lumbar knob connection. (the aftermarket seat covers are on there because the material used for this models seats is prone to excessive wear, and since this is a lease, i don't want that.) i advised the service adviser and service manager that the seat covers were just recently put on, (last week of august 2011) and in no way had anything to do with the broken lumbar knob connection. the service adviser said that i would have to bring it in another time for the regional rep to look at it, to determine if it would be fixed or not. i again advised, that it had absolutely nothing to do with it, and besides that, it's just nylon fabric that's put over the seat cushions. and they were not even on when it happened. the service manager said that's the only way that the dealership can get paid for it, is if the rep says so. so, the service manager, service writer, and technician at bob moore mazda okc are saying i'm lying about how the lumbar knob connection broke. also, when the vehicle was returned to me, the tech had reinstalled the seat belt twisted. shows the quality of service there. *tr.Mileage was 2000 miles. Vehicle Identification Number (VIN):1YVHZ8CHXA5. Mazda Mazda6 2010 problem was reported in OKLAHOMA CITY, OK. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda6 2010 Service Brakes, Hydraulic

Mazda Mazda6 2010 Service Brakes, Hydraulic Review #10436432

MAZDA MAZDA6 2010 car safety problem was reported on Nov 05, 2010.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with SERVICE BRAKES, HYDRAULIC . when applying foot to the brakes, the pedal "collapse" to the floor with little to no resistance. releasing the brake pedal and quickly pumping does regain some resistance, but braking is affected. the problem is intermittent and is not triggered by any specific event. *tr.Mileage was 6758 miles. Vehicle Identification Number (VIN):1YVHZ8CH4A5. Mazda Mazda6 2010 problem was reported in HOLDEN, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda6 2010 Tires

Mazda Mazda6 2010 Tires Review #10439688

MAZDA MAZDA6 2010 car safety problem was reported on Nov 29, 2011.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . both rear tire pressure sensors failed due to either over-tightening or corrosion. both sensors snapped off right below the sensor stem cap causing both rear tires to deflate. on a newer car still under warranty, mazda claims sensors are only covered until 36000 miles. and they're not cheap either ($80 each, not including installation.) *tr.Mileage was 47900 miles. Mazda Mazda6 2010 problem was reported in CROSBY, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Mazda Mazda6 2010 Wheels

Mazda Mazda6 2010 Wheels Review #10439688

MAZDA MAZDA6 2010 car safety problem was reported on Nov 29, 2011.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . both rear tire pressure sensors failed due to either over-tightening or corrosion. both sensors snapped off right below the sensor stem cap causing both rear tires to deflate. on a newer car still under warranty, mazda claims sensors are only covered until 36000 miles. and they're not cheap either ($80 each, not including installation.) *tr.Mileage was 47900 miles. Mazda Mazda6 2010 problem was reported in CROSBY, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Mazda Mazda6 2010 Electrical System

Mazda Mazda6 2010 Electrical System Review #10439688

MAZDA MAZDA6 2010 car safety problem was reported on Nov 29, 2011.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with ELECTRICAL SYSTEM . both rear tire pressure sensors failed due to either over-tightening or corrosion. both sensors snapped off right below the sensor stem cap causing both rear tires to deflate. on a newer car still under warranty, mazda claims sensors are only covered until 36000 miles. and they're not cheap either ($80 each, not including installation.) *tr.Mileage was 47900 miles. Mazda Mazda6 2010 problem was reported in CROSBY, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Mazda Mazda6 2010 Steering

Mazda Mazda6 2010 Steering Review #10458509

MAZDA MAZDA6 2010 car safety problem was reported on May 01, 2012.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with STEERING . the rotors are warped after less then 30k miles. this causes the car to shimmy when braking at any appreciable speed (any speed over 40mph). took car to dealer and they claim it is not covered under the warranty as it is "normal wear and tear". called mazda and they too refused to fix the problem under the warranty..0 person(s) were injured. 0 person(s) died.Mileage was 29889 miles. Mazda Mazda6 2010 problem was reported in ALEXANDRIA, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Mazda Mazda6 2010 Service Brakes

Mazda Mazda6 2010 Service Brakes Review #10458509

MAZDA MAZDA6 2010 car safety problem was reported on May 01, 2012.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with SERVICE BRAKES . the rotors are warped after less then 30k miles. this causes the car to shimmy when braking at any appreciable speed (any speed over 40mph). took car to dealer and they claim it is not covered under the warranty as it is "normal wear and tear". called mazda and they too refused to fix the problem under the warranty..0 person(s) were injured. 0 person(s) died.Mileage was 29889 miles. Mazda Mazda6 2010 problem was reported in ALEXANDRIA, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Mazda Mazda6 2010 Electrical System

Mazda Mazda6 2010 Electrical System Review #10469316

MAZDA MAZDA6 2010 car safety problem was reported on July 22, 2012.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with ELECTRICAL SYSTEM . my car was parked, went inside store for a minute, came out and it wouldn't start. no lights prior, and i take meticulous care of my car. after a failed jump, tow was issued. the mechanic says it's a starter failure- at 42,000 miles on a brand new factory line car. now mazda will not respond to complaints, and attempts at reaching any supervisors have been negated. car has been immobile for over two weeks. 42,000 is a premature failure for a brand new factory part- and the car company should pay to replace a defective portion of the vehicle. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 42000 miles. Vehicle Identification Number (VIN):1YVHZ8CHXA5. Mazda Mazda6 2010 problem was reported in ARVADA, CO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda6 2010 Exterior Lighting

Mazda Mazda6 2010 Exterior Lighting Review #10491611

MAZDA MAZDA6 2010 car safety problem was reported on Dec 29, 2012.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with EXTERIOR LIGHTING . just purchased an used 2010 mazda 6 and the passenger low-beam headlamp is "out" until you give it a nice friendly tap. this at only 29,300 miles. went out again 9 days later and the tap is not working. went online and found this link with other owners having the same issue. http://www.youtube.com/watch?v=uqqperresa8. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 29300 miles. Vehicle Identification Number (VIN):1YVHZ8CB8A5. Mazda Mazda6 2010 problem was reported in SAN DIEGO, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda6 2010 Vehicle Speed Control

Mazda Mazda6 2010 Vehicle Speed Control Review #10550912

MAZDA MAZDA6 2010 car safety problem was reported on July 09, 2013.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 mazda mazda6. the contact stated that while driving at various speeds, the vehicle accelerated on its own. the vehicle was taken to the dealer. the technician was unable to duplicate the failure. the manufacturer was not made aware of the failure. the vehicle was not repaired. the failure mileage was 17,000 and the current mileage was 25,000...updated 03/07/14 *bf .0 person(s) were injured. 0 person(s) died.Mileage was 17000 miles. Vehicle Identification Number (VIN):1YVHZ8BH9A5. Mazda Mazda6 2010 problem was reported in XENIA, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda6 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS.

Mazda Mazda6 2010 Exterior Lighting

Mazda Mazda6 2010 Exterior Lighting Review #10551071

MAZDA MAZDA6 2010 car safety problem was reported on Oct 15, 2013.MAZDA MAZDA6 2010, manufactured by MAZDA MOTOR CORP had a problem with EXTERIOR LIGHTING . tl* the contact owns a 2010 mazda mazda6. the contact stated while driving into the residential driveway, the passenger side low beam headlight burned out. the vehicle was not taken to the dealer. the manufacturer was made aware of the failure. the vehicle was not repaired. the failure mileage was 53,855 and the current mileage was 54,200. .0 person(s) were injured. 0 person(s) died.Mileage was 53855 miles. Vehicle Identification Number (VIN):1YVHZ8BH3A5. Mazda Mazda6 2010 problem was reported in OAK HILL, WV. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda6 2010 Engine And Engine Cooling

Mazda Mazda6 2010 Engine And Engine Cooling Review #10565712

MAZDA MAZDA6 2010 car safety problem was reported on June 27, 2013.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with ENGINE AND ENGINE COOLING . when stopped at a stop light vehicle would begin to raise in temperature and a/c would shut off. this happened several times. brought vehicle to dealer and was told they couldn't do anything unless they saw the vehicle have the problem. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 49500 miles. Mazda Mazda6 2010 problem was reported in WEST WARWICK, RI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda6 2010 Engine Review #10569417

MAZDA MAZDA6 2010 car safety problem was reported on Mar 13, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with ENGINE . my son took my car to school. he was going to leave after school let out, he was going to give his friend a ride home. this is a 6 speed car. his friend got in the car on the passenger side, my son was talking to his brother, he was not in the car. my son had put the keys on the driver seat, his friend put the key in the ignition and turned the key to accessories to listen to the radio, the car had the emergency brake on, and it was in first gear. when he turned the key to listen to the radio the car took off!!!! i am not sure how fast it was going but it crashed into a tree and stopped. there was no driver!! there is a police report on this, and there were several witnesses. my son's friend hit his head on the windshield and it cracked the windshield. i contacted mazda headquarters to make them aware, and they seemed bothered that i even called!!!!! it is a miracle a kid was not walking by and was struck by this out of control car. *tr.Vehicle was involved in a crash. 1 person(s) were injured. 0 person(s) died.Mileage was 53000 miles. Vehicle Identification Number (VIN):1YVHZ8BH7A5. Mazda Mazda6 2010 problem was reported in BILLINGS, MT. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.

Mazda Mazda6 2010 Power Train

Mazda Mazda6 2010 Power Train Review #10569417

MAZDA MAZDA6 2010 car safety problem was reported on Mar 13, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with POWER TRAIN . my son took my car to school. he was going to leave after school let out, he was going to give his friend a ride home. this is a 6 speed car. his friend got in the car on the passenger side, my son was talking to his brother, he was not in the car. my son had put the keys on the driver seat, his friend put the key in the ignition and turned the key to accessories to listen to the radio, the car had the emergency brake on, and it was in first gear. when he turned the key to listen to the radio the car took off!!!! i am not sure how fast it was going but it crashed into a tree and stopped. there was no driver!! there is a police report on this, and there were several witnesses. my son's friend hit his head on the windshield and it cracked the windshield. i contacted mazda headquarters to make them aware, and they seemed bothered that i even called!!!!! it is a miracle a kid was not walking by and was struck by this out of control car. *tr.Vehicle was involved in a crash. 1 person(s) were injured. 0 person(s) died.Mileage was 53000 miles. Vehicle Identification Number (VIN):1YVHZ8BH7A5. Mazda Mazda6 2010 problem was reported in BILLINGS, MT. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.

Mazda Mazda6 2010 Service Brakes

Mazda Mazda6 2010 Service Brakes Review #10584968

MAZDA MAZDA6 2010 car safety problem was reported on Apr 23, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with SERVICE BRAKES . the brake rotors on this vehicle need machining each year due to grabbing. my mazda dealership has machined them after the first year and replaced them under warranty at 30k. the replacement rotors are to be machined again on 4/26/14. this is a safety issue due to potential loss of control during braking. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 12000 miles. Vehicle Identification Number (VIN):1YVHZ8CH6A5. Mazda Mazda6 2010 problem was reported in MESA, AZ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Mazda Mazda6 2010 Tires Pressure Monitoring And Regulating Systems

Mazda Mazda6 2010 Tires Pressure Monitoring And Regulating Systems Review #10594775

MAZDA MAZDA6 2010 car safety problem was reported on May 19, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS . my husband was driving on the nj turnpike and the tire pressure monitor light came on. within a minute the rear passenger tire was completely flat. after inspected by a tire dealer, it was determined that the tpms corroded and the nut came off while driving the car. the tpms fell into the tire causing an immediate flat tire. warranty did not cover the defective tpms and mazda does not have a safety recall on this part. the part was replaced with a new rubber tpms.[original made of metal] this is an obvious concern if mazda is now replacing the part with a new material. this is a major safety concern as a major accident could have occurred. luckily, the incident did not result in an accident or injuries. now there is a concern for the other three tpms which are also corroded and the same issue can happen. mazda needs to issue a safety recall since i am afraid to drive my infant and toddler until all tpms are replaced with the new tpms design. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 48000 miles. Vehicle Identification Number (VIN):1YVHZ8CH2A5. Mazda Mazda6 2010 problem was reported in WYCKOFF, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Mazda Mazda6 2010 Wheels

Mazda Mazda6 2010 Wheels Review #10594775

MAZDA MAZDA6 2010 car safety problem was reported on May 19, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with WHEELS . my husband was driving on the nj turnpike and the tire pressure monitor light came on. within a minute the rear passenger tire was completely flat. after inspected by a tire dealer, it was determined that the tpms corroded and the nut came off while driving the car. the tpms fell into the tire causing an immediate flat tire. warranty did not cover the defective tpms and mazda does not have a safety recall on this part. the part was replaced with a new rubber tpms.[original made of metal] this is an obvious concern if mazda is now replacing the part with a new material. this is a major safety concern as a major accident could have occurred. luckily, the incident did not result in an accident or injuries. now there is a concern for the other three tpms which are also corroded and the same issue can happen. mazda needs to issue a safety recall since i am afraid to drive my infant and toddler until all tpms are replaced with the new tpms design. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 48000 miles. Vehicle Identification Number (VIN):1YVHZ8CH2A5. Mazda Mazda6 2010 problem was reported in WYCKOFF, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Mazda Mazda6 2010 Structure

Mazda Mazda6 2010 Structure Review #10594892

MAZDA MAZDA6 2010 car safety problem was reported on May 31, 2011.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE . i would like to report this ongoing issue with my mazda 6 2010 model. the way mazda design side mirror that's very comfy for spider. our both left & right mirror has spider web all the time. we need to clean that in all seasons. there are multiple safety recall for mazda 6 2010. [xxx] information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6). *tr.0 person(s) were injured. 0 person(s) died.Mileage was 2500 miles. Vehicle Identification Number (VIN):1YVHZ8BH3A5. Mazda Mazda6 2010 problem was reported in MILL VALLEY, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda6 2010 Visibility Rearview Mirrors/devices

Mazda Mazda6 2010 Visibility Rearview Mirrors/devices Review #10594892

MAZDA MAZDA6 2010 car safety problem was reported on May 31, 2011.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY:REARVIEW MIRRORS/DEVICES . i would like to report this ongoing issue with my mazda 6 2010 model. the way mazda design side mirror that's very comfy for spider. our both left & right mirror has spider web all the time. we need to clean that in all seasons. there are multiple safety recall for mazda 6 2010. [xxx] information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6). *tr.0 person(s) were injured. 0 person(s) died.Mileage was 2500 miles. Vehicle Identification Number (VIN):1YVHZ8BH3A5. Mazda Mazda6 2010 problem was reported in MILL VALLEY, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda6 2010 Service Brakes

Mazda Mazda6 2010 Service Brakes Review #10597367

MAZDA MAZDA6 2010 car safety problem was reported on Apr 09, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with SERVICE BRAKES . tl* the contact owns a 2010 mazda mazda6. the contact stated that the rotors were prematurely warped, causing the vehicle to jerk violently. also, the contact mentioned that the tpms and passenger air bag warning lamp illuminated. the vehicle was taken to the dealer. the technician was unable to diagnose the failure. the manufacturer was made aware of the failure. the vehicle was not repaired. the vin was not available. the failure mileage was 30,000 and the current mileage was 60,000. .0 person(s) were injured. 0 person(s) died.Mileage was 30000 miles. Mazda Mazda6 2010 problem was reported in LOUISVILLE, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda6 2010 Service Brakes, Hydraulic Foundation Components Disc Rotor

Mazda Mazda6 2010 Service Brakes, Hydraulic Foundation Components Disc Rotor Review #10597367

MAZDA MAZDA6 2010 car safety problem was reported on Apr 09, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:ROTOR . tl* the contact owns a 2010 mazda mazda6. the contact stated that the rotors were prematurely warped, causing the vehicle to jerk violently. also, the contact mentioned that the tpms and passenger air bag warning lamp illuminated. the vehicle was taken to the dealer. the technician was unable to diagnose the failure. the manufacturer was made aware of the failure. the vehicle was not repaired. the vin was not available. the failure mileage was 30,000 and the current mileage was 60,000. .0 person(s) were injured. 0 person(s) died.Mileage was 30000 miles. Mazda Mazda6 2010 problem was reported in LOUISVILLE, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda6 2010 Exterior Lighting

Mazda Mazda6 2010 Exterior Lighting Review #10597375

MAZDA MAZDA6 2010 car safety problem was reported on June 10, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with EXTERIOR LIGHTING . my brake rotors are completely warped! after 6 months of having my car my brakes have gone out multiple times, i don't not drive my car long distances or even on a daily basis. i can be going as slow as 25 mph and when i go to brake my car will start to shake (not much but noticeable) this is very dangerous due to the fact it can cause loss of control while braking. i have taken my car to the dealer and had it worked on under a "one time" warranty meaning they will maintenance the brake once at no cost to me. each time i have gone or spoken to my dealer they say they can't figure out why it keeps happening and even said it could be normal wear and tear (which is not the case). i am apart of a regional mazda club and everyone with a mazda 6 (2009-12) seem to have the exact same problem with this. also, the tire pressure light stays on. almost immediately after i purchased my car the light came on followed by the loud beeping sound that warns you that your tire pressure is low. i called my dealer and they looked at it and told my i just need air. well the very next day the light came on and the loud beeping followed. a long with that my passenger seat air bag light keeps say that the air bag is off, and the passenger seat low beam headlight has issues with stay on. *tr.0 person(s) were injured. 0 person(s) died.Mazda Mazda6 2010 problem was reported in LOUISVILLE, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda6 2010 Service Brakes

Mazda Mazda6 2010 Service Brakes Review #10597375

MAZDA MAZDA6 2010 car safety problem was reported on June 10, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with SERVICE BRAKES . my brake rotors are completely warped! after 6 months of having my car my brakes have gone out multiple times, i don't not drive my car long distances or even on a daily basis. i can be going as slow as 25 mph and when i go to brake my car will start to shake (not much but noticeable) this is very dangerous due to the fact it can cause loss of control while braking. i have taken my car to the dealer and had it worked on under a "one time" warranty meaning they will maintenance the brake once at no cost to me. each time i have gone or spoken to my dealer they say they can't figure out why it keeps happening and even said it could be normal wear and tear (which is not the case). i am apart of a regional mazda club and everyone with a mazda 6 (2009-12) seem to have the exact same problem with this. also, the tire pressure light stays on. almost immediately after i purchased my car the light came on followed by the loud beeping sound that warns you that your tire pressure is low. i called my dealer and they looked at it and told my i just need air. well the very next day the light came on and the loud beeping followed. a long with that my passenger seat air bag light keeps say that the air bag is off, and the passenger seat low beam headlight has issues with stay on. *tr.0 person(s) were injured. 0 person(s) died.Mazda Mazda6 2010 problem was reported in LOUISVILLE, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda6 2010 Tires Pressure Monitoring And Regulating Systems

Mazda Mazda6 2010 Tires Pressure Monitoring And Regulating Systems Review #10597375

MAZDA MAZDA6 2010 car safety problem was reported on June 10, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS . my brake rotors are completely warped! after 6 months of having my car my brakes have gone out multiple times, i don't not drive my car long distances or even on a daily basis. i can be going as slow as 25 mph and when i go to brake my car will start to shake (not much but noticeable) this is very dangerous due to the fact it can cause loss of control while braking. i have taken my car to the dealer and had it worked on under a "one time" warranty meaning they will maintenance the brake once at no cost to me. each time i have gone or spoken to my dealer they say they can't figure out why it keeps happening and even said it could be normal wear and tear (which is not the case). i am apart of a regional mazda club and everyone with a mazda 6 (2009-12) seem to have the exact same problem with this. also, the tire pressure light stays on. almost immediately after i purchased my car the light came on followed by the loud beeping sound that warns you that your tire pressure is low. i called my dealer and they looked at it and told my i just need air. well the very next day the light came on and the loud beeping followed. a long with that my passenger seat air bag light keeps say that the air bag is off, and the passenger seat low beam headlight has issues with stay on. *tr.0 person(s) were injured. 0 person(s) died.Mazda Mazda6 2010 problem was reported in LOUISVILLE, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda6 2010 Unknown Or Other

Mazda Mazda6 2010 Unknown Or Other Review #10606972

MAZDA MAZDA6 2010 car safety problem was reported on Nov 26, 2013.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . hi, my mazda have a melt dash.0 person(s) were injured. 0 person(s) died.Mazda Mazda6 2010 problem was reported in TAMPA, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda6 2010 Unknown Or Other Review #10610002

MAZDA MAZDA6 2010 car safety problem was reported on June 30, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . i have had my well maintained car for just under 5 years. it is out of warranty. i have never used a chemical cleaning product to clean the interior, just a damp cloth. i noticed that only the section of dashboard that covers the airbag on the passenger side was sticky. within a few days it became progressively worse and actually gooey. if it was touched by a window sun screen or by your hand, the dashboard color and material rolled off and spread to anything that was accidentally retouched. the 800 number mazda customer assistance center told me that it was up to the mazda dealership to decide what could be done about the problem. paretti mazda at 4000 veterans blvd., metairie, la 70002 had me bring the car in on july 2, 2014 when the mazda district representative was available to look at it. at 3:00 p.m. that same day, i was told that i had to decide before 5:00 p.m. whether or not i would accept the offer of mazda giving me a new $226.96 dashboard part and my having to pay $324.84 to them for labor. it was a one time only offer for that day. the entire scenario is unethical. i had no other choice but to let mazda do this job and i was told that it may happen again in a few years. they do not stand behind the replacement part. the car was not ready by the end of today 7/11/2014 as promised because of "unforeseen problems." paretti mazda is now renting a car for me to use for the next 3 days because of the weekend. .0 person(s) were injured. 0 person(s) died.Mileage was 39413 miles. Vehicle Identification Number (VIN):1YVHZ8BH7A5. Mazda Mazda6 2010 problem was reported in METAIRIE, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda6 2010 Unknown Or Other Review #10610137

MAZDA MAZDA6 2010 car safety problem was reported on June 02, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . i have a 2010 mazda 6 and recently noticed that my dashboard is melting..0 person(s) were injured. 0 person(s) died.Mazda Mazda6 2010 problem was reported in LOXAHATCHEE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda6 2010 Unknown Or Other Review #10621425

MAZDA MAZDA6 2010 car safety problem was reported on Aug 11, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dashboard on the passenger side of my car is starting to melt. it is very sticky and shiny. .0 person(s) were injured. 0 person(s) died.Mileage was 87000 miles. Mazda Mazda6 2010 problem was reported in ORLANDO, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda6 2010 Unknown Or Other Review #10628137

MAZDA MAZDA6 2010 car safety problem was reported on Aug 04, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . car surges forward when you slow down or is stopping to park..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):1YVHZ8BHXA5. Mazda Mazda6 2010 problem was reported in WEST PALM BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda6 2010 Unknown Or Other Review #10633145

MAZDA MAZDA6 2010 car safety problem was reported on Aug 01, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . my vehicle's dashboard is meting creating a glare when i am driving affecting my vision and putting me, my family and others at a safety risk. to make matters worse, the glue-like material is smearing and fogging my windshield also affecting my vision and making the interior sticky. the car has cloth seats and it is getting all over the seats, steering wheel, carpets, and clothing. the vehicle has very few miles, this should not be occuring. it is definitely the result of a defect and a recall must be put in place for this safety hazzard. consumers should not be exposed and have to be injured or die before action is taken. i am very dissapointed to read that mazda and other auto makers are not paying to fix this issue. i have contact information for over 8,500 companies in the u.s. and i am going to be sending an email blast to make it public so that everyone stays away from buying a mazda. ironically, i have to take the vehicle in for another recall on the door latch that is defective and it is opening while my wife is driving..0 person(s) were injured. 0 person(s) died.Mileage was 41000 miles. Vehicle Identification Number (VIN):1YVHZ8BH5A5. Mazda Mazda6 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda6 2010 Unknown Or Other Review #10638619

MAZDA MAZDA6 2010 car safety problem was reported on Sept 01, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . my dashboard on the passenger side is melting. .0 person(s) were injured. 0 person(s) died.Mileage was 45000 miles. Vehicle Identification Number (VIN):1YVHZ8BH4A5. Mazda Mazda6 2010 problem was reported in JACKSONVILLE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda6 2010 Suspension

Mazda Mazda6 2010 Suspension Review #10650268

MAZDA MAZDA6 2010 car safety problem was reported on Feb 01, 2010.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with SUSPENSION . this vehicle does not track straight, even on a level road. at highway speeds (above 50 mph) it has a decided pull to the left, regardless of the lateral slope of the road. constant clockwise pressure on the steering wheel is necessary in order to keep vehicle from drifting in a leftward direction. if driver attention is diverted for only an instant the vehicle is likely to partially intrude into the lane to the left, which on an undivided highway could be an oncoming traffic lane (hence the safety issue). i called this to the attention of my mazda dealer's service department at least twice within the first year after purchase (january 2010). their answer was no answer--they could not find anything wrong mechanically and there were no bulletins from mazda on the subject. they verified the alignment and rotated the tires left to right, but neither of these solved the problem. nearly five years later the problem still exists and seems even more pronounced than it was originally. a recent check with the dealer indicated that there is still nothing from mazda. possibly it is a defect that applies only to my car and not in general to that model, but i have no way of determining that at this point..0 person(s) were injured. 0 person(s) died.Mileage was 500 miles. Vehicle Identification Number (VIN):1YVHZ8CH1A5. Mazda Mazda6 2010 problem was reported in STAMFORD, CT. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Mazda Mazda6 2010 Unknown Or Other

Mazda Mazda6 2010 Unknown Or Other Review #10650268

MAZDA MAZDA6 2010 car safety problem was reported on Feb 01, 2010.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . this vehicle does not track straight, even on a level road. at highway speeds (above 50 mph) it has a decided pull to the left, regardless of the lateral slope of the road. constant clockwise pressure on the steering wheel is necessary in order to keep vehicle from drifting in a leftward direction. if driver attention is diverted for only an instant the vehicle is likely to partially intrude into the lane to the left, which on an undivided highway could be an oncoming traffic lane (hence the safety issue). i called this to the attention of my mazda dealer's service department at least twice within the first year after purchase (january 2010). their answer was no answer--they could not find anything wrong mechanically and there were no bulletins from mazda on the subject. they verified the alignment and rotated the tires left to right, but neither of these solved the problem. nearly five years later the problem still exists and seems even more pronounced than it was originally. a recent check with the dealer indicated that there is still nothing from mazda. possibly it is a defect that applies only to my car and not in general to that model, but i have no way of determining that at this point..0 person(s) were injured. 0 person(s) died.Mileage was 500 miles. Vehicle Identification Number (VIN):1YVHZ8CH1A5. Mazda Mazda6 2010 problem was reported in STAMFORD, CT. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Mazda Mazda6 2010 Steering

Mazda Mazda6 2010 Steering Review #10650268

MAZDA MAZDA6 2010 car safety problem was reported on Feb 01, 2010.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with STEERING . this vehicle does not track straight, even on a level road. at highway speeds (above 50 mph) it has a decided pull to the left, regardless of the lateral slope of the road. constant clockwise pressure on the steering wheel is necessary in order to keep vehicle from drifting in a leftward direction. if driver attention is diverted for only an instant the vehicle is likely to partially intrude into the lane to the left, which on an undivided highway could be an oncoming traffic lane (hence the safety issue). i called this to the attention of my mazda dealer's service department at least twice within the first year after purchase (january 2010). their answer was no answer--they could not find anything wrong mechanically and there were no bulletins from mazda on the subject. they verified the alignment and rotated the tires left to right, but neither of these solved the problem. nearly five years later the problem still exists and seems even more pronounced than it was originally. a recent check with the dealer indicated that there is still nothing from mazda. possibly it is a defect that applies only to my car and not in general to that model, but i have no way of determining that at this point..0 person(s) were injured. 0 person(s) died.Mileage was 500 miles. Vehicle Identification Number (VIN):1YVHZ8CH1A5. Mazda Mazda6 2010 problem was reported in STAMFORD, CT. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Mazda Mazda6 2010 Unknown Or Other

Mazda Mazda6 2010 Unknown Or Other Review #10651046

MAZDA MAZDA6 2010 car safety problem was reported on Oct 15, 2013.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . my passenger side dashboard has appeared to be melting for awhile now. i never thought to check on it until i decided to google how i could fix the problem. it causes a glare and the sticky substance gets on anything that gets near it and it seems to be spreading further down the panel. also it can't be cleaned so is collecting dust and debris..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):1YVHZ8CH0A5. Mazda Mazda6 2010 problem was reported in DANIA BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda6 2010 Structure Body

Mazda Mazda6 2010 Structure Body Review #10653053

MAZDA MAZDA6 2010 car safety problem was reported on Oct 01, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE:BODY . dashboard crash pad on the passenger side is melting. i live in florida and use a sun screen in my window when the vehicle is parked. causes dash to become shiny and there is a glare when driving. .0 person(s) were injured. 0 person(s) died.Mileage was 48000 miles. Vehicle Identification Number (VIN):1YVHZ8BH8A5. Mazda Mazda6 2010 problem was reported in BOYNTON BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda6 2010 Unknown Or Other

Mazda Mazda6 2010 Unknown Or Other Review #10653830

MAZDA MAZDA6 2010 car safety problem was reported on Feb 03, 2014.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . my mazda dashboard is melting. it is very sticky, shiny and i cannot the stand the smell of it. since the dashboard became shiny it reflects light in to my eyes and it kind of blinds me sometimes. i cannot clean it or touch it..0 person(s) were injured. 0 person(s) died.Mazda Mazda6 2010 problem was reported in ORLANDO, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda6 2010 Fuel/propulsion System

Mazda Mazda6 2010 Fuel/propulsion System Review #10660679

MAZDA MAZDA6 2010 car safety problem was reported on Apr 15, 2013.MAZDA MAZDA6 2010, manufactured by Mazda Motor Corp. had a problem with FUEL/PROPULSION SYSTEM . vehicle was repaired as part of nhtsa campaign number: 11v134000 on 21 july 2011. however, vehicle's fuel tank cracked in april 2013 and had to be replaced at owner's expense. after smelling gasoline after fill up and noticing a puddle of gasoline in driveway in april 2013, owner had vehicle towed to mazda dealer for repair. dealer replaced tank on 15 april 2013. over the last year and several attempts, mazda has since declined to reimburse owner for repair and reprogram ecu per nhtsa campaign number: 14v114000. recall from july 2011 was supposed to eliminate the possibly of a cracked fuel tank, but it didn't. owner has pictures of cracked tank and dealer work orders from july 2011 and april 2013 and can provide if needed. owner worried that if the ecu isn't reprogrammed, the tank will crack again..0 person(s) were injured. 0 person(s) died.Mileage was 58627 miles. Vehicle Identification Number (VIN):1YVHZ8CHXA5. Mazda Mazda6 2010 problem was reported in MOUNT HOLLY, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Air Bags Frontal 1 Review(s)

Electrical System 4 Review(s)

Engine 1 Review(s)

Engine And Engine Cooling 1 Review(s)

Exterior Lighting 4 Review(s)

Fuel/propulsion System 1 Review(s)

Power Train 1 Review(s)

Seats 1 Review(s)

Service Brakes 4 Review(s)

Service Brakes, Hydraulic 3 Review(s)

Service Brakes, Hydraulic Foundation Components Disc Rotor 1 Review(s)

Steering 2 Review(s)

Structure 1 Review(s)

Structure Body 1 Review(s)

Structure Body Bumpers 1 Review(s)

Suspension 1 Review(s)

Tires 2 Review(s)

Tires Pressure Monitoring And Regulating Systems 3 Review(s)

Unknown Or Other 10 Review(s)

Vehicle Speed Control 1 Review(s)

Visibility Rearview Mirrors/devices 1 Review(s)

Wheels 2 Review(s)