Car-and-Safety.com

Mazda Mazda6 2008 Electrical System

Mazda Mazda6 2008 Electrical System Review #10248667

MAZDA MAZDA6 2008 car safety problem was reported on Sept 29, 2008.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with ELECTRICAL SYSTEM . 2008 mazda 6 with less than 5000 miles. starter caught on fire, dealer said rodent chewed wire. not a warranty issue. my insurance had to pay. pictures taken and my agent insured me when he filed with mazda they would take care of this. today 11/11/08 claim denied mazda said its not their fault. what ever happened to customer service. *tr.Vehicle was on fire. 0 person(s) were injured. 0 person(s) died.Mileage was 4955 miles. Vehicle Identification Number (VIN):1YVHP81C085. Mazda Mazda6 2008 problem was reported in CRESTWOOD, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda6 2008 Visibility

Mazda Mazda6 2008 Visibility Review #10252882

MAZDA MAZDA6 2008 car safety problem was reported on Dec 24, 2008.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with VISIBILITY . i accidentally touched the moonroof controls on my car and this blew a fuse which was also connected to the heat, causing dangerous driving conditions (none of my windows defrosted). they said the moonroof was frozen shut and by me touching the control it overloaded the fuse. when i went to walser mazda in burnsville they told me they had seen 3 of these same incidents in one week. because i didn't know it was just a fuse at the time i was unable to safely drive the vehicle. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 6700 miles. Mazda Mazda6 2008 problem was reported in BURNSVILLE, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Mazda Mazda6 2008 Visibility Windshield Wiper/washer

Mazda Mazda6 2008 Visibility Windshield Wiper/washer Review #10260561

MAZDA MAZDA6 2008 car safety problem was reported on Mar 02, 2009.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with VISIBILITY:WINDSHIELD WIPER/WASHER . tl*the contact owns a 2008 mazda 6. while driving approximately 68 mph in rainy weather conditions, the windshield wipers failed to activate. the failure caused poor visibilty and occurred without warning. the authorized dealer was notified of the malfunction. due to massive rain conditions, the vehicle has not been taken in for repair. the failure and current mileages were 6,900. .0 person(s) were injured. 0 person(s) died.Mileage was 6900 miles. Vehicle Identification Number (VIN):1YVHP80C785. Mazda Mazda6 2008 problem was reported in BAKER CITY, OR. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 68 mph.

Mazda Mazda6 2008 Electrical System

Mazda Mazda6 2008 Electrical System Review #10308957

MAZDA MAZDA6 2008 car safety problem was reported on Jan 29, 2010.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with ELECTRICAL SYSTEM . november , 17 , 2009 - car lost power while driving ,and came to a stop on the road.car towed in at compass mazda in middletown,ny. after one day of sitting at the dealership ,car started by itself . paid $ 48.00 for diagnosis. january, 1, 2010 - car did not start . car towed in at mazda palisades in west nyack,ny. again , car started at the dealership after sitting for a day. january , 8, 2010 - car did not start . mazda palisades in west nyack did not accept the car to be towed in stating that they do not have a trained mazda mechanic . in this situation , the car was towed in at compass mazda in middletown , ny . tow service $ 150.00 . at fault was a poor / loose connection ( ground wire ) . cost of reparation : $ 378.44. january , 29 , 2010 . car lost power while driving and came to a stop on the road . car towed in at compass mazda in middletown , ny . fuel pump relay was replaced . this time there was no charge for the repair . *tr.Mileage was 37363 miles. Vehicle Identification Number (VIN):1YVHP80C885. Mazda Mazda6 2008 problem was reported in MIDDLETOWN, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Mazda Mazda6 2008 Fuel System, Gasoline

Mazda Mazda6 2008 Fuel System, Gasoline Review #10308957

MAZDA MAZDA6 2008 car safety problem was reported on Jan 29, 2010.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with FUEL SYSTEM, GASOLINE . november , 17 , 2009 - car lost power while driving ,and came to a stop on the road.car towed in at compass mazda in middletown,ny. after one day of sitting at the dealership ,car started by itself . paid $ 48.00 for diagnosis. january, 1, 2010 - car did not start . car towed in at mazda palisades in west nyack,ny. again , car started at the dealership after sitting for a day. january , 8, 2010 - car did not start . mazda palisades in west nyack did not accept the car to be towed in stating that they do not have a trained mazda mechanic . in this situation , the car was towed in at compass mazda in middletown , ny . tow service $ 150.00 . at fault was a poor / loose connection ( ground wire ) . cost of reparation : $ 378.44. january , 29 , 2010 . car lost power while driving and came to a stop on the road . car towed in at compass mazda in middletown , ny . fuel pump relay was replaced . this time there was no charge for the repair . *tr.Mileage was 37363 miles. Vehicle Identification Number (VIN):1YVHP80C885. Mazda Mazda6 2008 problem was reported in MIDDLETOWN, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 55 mph.

Mazda Mazda6 2008 Service Brakes, Hydraulic Foundation Components Disc Rotor

Mazda Mazda6 2008 Service Brakes, Hydraulic Foundation Components Disc Rotor Review #10323291

MAZDA MAZDA6 2008 car safety problem was reported on May 12, 2009.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:ROTOR . tl* the contact owns a 2008 mazda 6. the contact stated when coming to a stop after driving at approximately 50 mph, the vehicle would shake. the vehicle was taken to an authorized dealer where the front rotors were replaced. the failure mileage was 8,948. the current mileage was 18,243..Mileage was 8948 miles. Vehicle Identification Number (VIN):1YVHP80C985. Mazda Mazda6 2008 problem was reported in MARANA, AZ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 50 mph.

Mazda Mazda6 2008 Engine And Engine Cooling Engine

Mazda Mazda6 2008 Engine And Engine Cooling Engine Review #10325083

MAZDA MAZDA6 2008 car safety problem was reported on Aug 01, 2008.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with ENGINE AND ENGINE COOLING:ENGINE . 1. there was no warning to this failure, i was on a motorway (u.k) i check my oil levels every single week 2. i had an engine over-run and could only be stopped by switching the engine off, the rev counter hit maximum and a huge cloud of white smoke was left behind me. consequences are now i am left without a car and i could have died because i was approaching a roundabout 700 yards away and swerved between 2 lanes of moving traffic to force a stop on a lay-by. 3. nothing was done, mazda are blaming me for the incident even after i had my oil checked and results shown a 62% diesel oil contamination, they blame the dpf (diesel particulate filter) for this over-run as i am not doing enough "long journey" miles. which i was, no warning lights appeared before or after the incident and the oil levels are dramatically above the full mark. no fault codes are shown on mazda computer. my car is sitting useless on my drive as we are all to scared to drive it. *tr.Mileage was 11987 miles. Vehicle Identification Number (VIN):JMZGH12D611. Mazda Mazda6 2008 problem was reported in LONDON, 00. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 100 mph.

Mazda Mazda6 2008 Electrical System

Mazda Mazda6 2008 Electrical System Review #10325083

MAZDA MAZDA6 2008 car safety problem was reported on Aug 01, 2008.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with ELECTRICAL SYSTEM . 1. there was no warning to this failure, i was on a motorway (u.k) i check my oil levels every single week 2. i had an engine over-run and could only be stopped by switching the engine off, the rev counter hit maximum and a huge cloud of white smoke was left behind me. consequences are now i am left without a car and i could have died because i was approaching a roundabout 700 yards away and swerved between 2 lanes of moving traffic to force a stop on a lay-by. 3. nothing was done, mazda are blaming me for the incident even after i had my oil checked and results shown a 62% diesel oil contamination, they blame the dpf (diesel particulate filter) for this over-run as i am not doing enough "long journey" miles. which i was, no warning lights appeared before or after the incident and the oil levels are dramatically above the full mark. no fault codes are shown on mazda computer. my car is sitting useless on my drive as we are all to scared to drive it. *tr.Mileage was 11987 miles. Vehicle Identification Number (VIN):JMZGH12D611. Mazda Mazda6 2008 problem was reported in LONDON, 00. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 100 mph.

Mazda Mazda6 2008 Fuel System, Diesel

Mazda Mazda6 2008 Fuel System, Diesel Review #10325083

MAZDA MAZDA6 2008 car safety problem was reported on Aug 01, 2008.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with FUEL SYSTEM, DIESEL . 1. there was no warning to this failure, i was on a motorway (u.k) i check my oil levels every single week 2. i had an engine over-run and could only be stopped by switching the engine off, the rev counter hit maximum and a huge cloud of white smoke was left behind me. consequences are now i am left without a car and i could have died because i was approaching a roundabout 700 yards away and swerved between 2 lanes of moving traffic to force a stop on a lay-by. 3. nothing was done, mazda are blaming me for the incident even after i had my oil checked and results shown a 62% diesel oil contamination, they blame the dpf (diesel particulate filter) for this over-run as i am not doing enough "long journey" miles. which i was, no warning lights appeared before or after the incident and the oil levels are dramatically above the full mark. no fault codes are shown on mazda computer. my car is sitting useless on my drive as we are all to scared to drive it. *tr.Mileage was 11987 miles. Vehicle Identification Number (VIN):JMZGH12D611. Mazda Mazda6 2008 problem was reported in LONDON, 00. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 100 mph.

Mazda Mazda6 2008 Power Train Manual Transmission

Mazda Mazda6 2008 Power Train Manual Transmission Review #10325083

MAZDA MAZDA6 2008 car safety problem was reported on Aug 01, 2008.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN:MANUAL TRANSMISSION . 1. there was no warning to this failure, i was on a motorway (u.k) i check my oil levels every single week 2. i had an engine over-run and could only be stopped by switching the engine off, the rev counter hit maximum and a huge cloud of white smoke was left behind me. consequences are now i am left without a car and i could have died because i was approaching a roundabout 700 yards away and swerved between 2 lanes of moving traffic to force a stop on a lay-by. 3. nothing was done, mazda are blaming me for the incident even after i had my oil checked and results shown a 62% diesel oil contamination, they blame the dpf (diesel particulate filter) for this over-run as i am not doing enough "long journey" miles. which i was, no warning lights appeared before or after the incident and the oil levels are dramatically above the full mark. no fault codes are shown on mazda computer. my car is sitting useless on my drive as we are all to scared to drive it. *tr.Mileage was 11987 miles. Vehicle Identification Number (VIN):JMZGH12D611. Mazda Mazda6 2008 problem was reported in LONDON, 00. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 100 mph.

Mazda Mazda6 2008 Seat Belts

Mazda Mazda6 2008 Seat Belts Review #10325754

MAZDA MAZDA6 2008 car safety problem was reported on Apr 07, 2010.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with SEAT BELTS . i purchased a 2008 madza 6 in march of 2009 and the front passenger safety belt would lock intermittently. in june 2009 my husband took the car back to sesi motors and advised them of the problem and they supposedly fixed it. however on april 7, 2010 my husband and son was in a car accident and my son had on his seatbelt however his head hit the windshield. when my husband went to take off the seatbelt it was not fastened the lock did not hold causing my sons head to hit the windshield. he sustained injuries he was unconscious for approximately 10 minutes before ems got to him and he had a concussion. my son is now complaining of headaches, back aches and neck pains. *tr.Vehicle was involved in a crash. 2 person(s) were injured. Mileage was 56000 miles. Vehicle Identification Number (VIN):1YVHP80C485. Mazda Mazda6 2008 problem was reported in WESTLAND, MI. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Mazda Mazda6 2008 Air Bags Side/window

Mazda Mazda6 2008 Air Bags Side/window Review #10335714

MAZDA MAZDA6 2008 car safety problem was reported on June 08, 2010.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with AIR BAGS:SIDE/WINDOW . i was driving the morning of 6/8/10 on my way to work. there was a car going to pass me on a illinois rte 161 road. i slowed down for courtesy of the passer and i caught loose gravel on the hard road. instantly i knew not to over correct and try to ease out of it. i end up barrel rolling aprox 80+ feet down a steep reveen. no air bags deployed. my 2008 mazda 6 is equipped with side curtain airbags, which are roll over protection safety feature. as quoted on a internet site. i rolled aprox 4-6 times. *tr.Vehicle was involved in a crash. Mileage was 49000 miles. Vehicle Identification Number (VIN):1YVHP80C985. Mazda Mazda6 2008 problem was reported in CENTRALIA, IL. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Mazda Mazda6 2008 Power Train

Mazda Mazda6 2008 Power Train Review #10339937

MAZDA MAZDA6 2008 car safety problem was reported on June 24, 2010.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . placed our 2008 mazda 6 in reverse, the steering wheel locked up, the brake pedal would not engage and car rolled back into a telephone pole, causing moderate damage to rear of vehicle. no warning of any previous failures. *tr.Vehicle was involved in a crash. Mileage was 33000 miles. Vehicle Identification Number (VIN):1YVHP80C985. Mazda Mazda6 2008 problem was reported in DALLAS, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 5 mph.

Mazda Mazda6 2008 Service Brakes, Hydraulic

Mazda Mazda6 2008 Service Brakes, Hydraulic Review #10339937

MAZDA MAZDA6 2008 car safety problem was reported on June 24, 2010.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with SERVICE BRAKES, HYDRAULIC . placed our 2008 mazda 6 in reverse, the steering wheel locked up, the brake pedal would not engage and car rolled back into a telephone pole, causing moderate damage to rear of vehicle. no warning of any previous failures. *tr.Vehicle was involved in a crash. Mileage was 33000 miles. Vehicle Identification Number (VIN):1YVHP80C985. Mazda Mazda6 2008 problem was reported in DALLAS, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 5 mph.

Mazda Mazda6 2008 Steering

Mazda Mazda6 2008 Steering Review #10339937

MAZDA MAZDA6 2008 car safety problem was reported on June 24, 2010.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with STEERING . placed our 2008 mazda 6 in reverse, the steering wheel locked up, the brake pedal would not engage and car rolled back into a telephone pole, causing moderate damage to rear of vehicle. no warning of any previous failures. *tr.Vehicle was involved in a crash. Mileage was 33000 miles. Vehicle Identification Number (VIN):1YVHP80C985. Mazda Mazda6 2008 problem was reported in DALLAS, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 5 mph.

Mazda Mazda6 2008 Fuel System, Gasoline

Mazda Mazda6 2008 Fuel System, Gasoline Review #10349499

MAZDA MAZDA6 2008 car safety problem was reported on Aug 14, 2010.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with FUEL SYSTEM, GASOLINE . my stepson was involved in a rear-end collision with a 2008 mazda 6. the damage is severe enough to the left rear area of the car i believe the car is totaled. it was a 40-50 mph impact. the fuel tank was exposed after the accident and crushed. my concern and complaint is why didn't the fuel safety cutoff activate after a hard impact in the rear? i believe there is a device mandated by federal laws that after a rear end collision of this magnitude that the car would not start after the impact. in this case it did start and run smooth. i would like to have someone investigate as to why this device wasn't not properly functioning at the time of the accident. i will also notify mazda and my insurance company of this defect as well. *tr .Vehicle was involved in a crash. Mileage was 39500 miles. Mazda Mazda6 2008 problem was reported in CITY OF INDUSTRY, CA. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Mazda Mazda6 2008 Service Brakes, Hydraulic

Mazda Mazda6 2008 Service Brakes, Hydraulic Review #10353779

MAZDA MAZDA6 2008 car safety problem was reported on Aug 16, 2010.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with SERVICE BRAKES, HYDRAULIC . we noticed that suddenly our 2 year old mazda 6, with about 18,000 miles was barely braking. it has been serviced regularly and had a brake inspection at the dealership 2,000 miles and 5 months previously. the front brakes did not seem to be engaging at all, and we noted rust build up on the disc that no amount of braking could remove. an inspection at an independent shop revealed less than 10% remaining life on the rear brakes, and they noted that excessive rust had caused the brakes to rust out. the car is operated in kentucky--not exactly the center of the rust belt. i think defective brake materials are likely causing this unexpected and premature brake failure. while we did not experience an accident as a result, another driver may. i am writing in case other owners have had a similar issue with the 2008 mazda 6. *tr.Mileage was 18680 miles. Vehicle Identification Number (VIN):1YVHP80C185. Mazda Mazda6 2008 problem was reported in LEXINGTON, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 25 mph.

Mazda Mazda6 2008 Air Bags

Mazda Mazda6 2008 Air Bags Review #10367916

MAZDA MAZDA6 2008 car safety problem was reported on Nov 24, 2010.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with AIR BAGS . tl*the contact owns a 2008 mazda 6. while driving approximately 35 mph, the contact hit a deer causing her to crash. the air bags did not deploy. the dealer had not been contacted. the manufacturer had not been notified. a police report was not filed. the vehicle was not repaired. the current and failure mileages were approximately 65,000. .Vehicle was involved in a crash. Mileage was 65000 miles. Vehicle Identification Number (VIN):1YVHP80C185. Mazda Mazda6 2008 problem was reported in RIDGELEY, WV. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Mazda Mazda6 2008 Air Bags Review #10369088

MAZDA MAZDA6 2008 car safety problem was reported on Oct 29, 2010.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with AIR BAGS . tl*the contact owns a 2008 mazda, mazda6. while the contact was driving approximately 40 mph, the vehicle was involved in a crash and the air bags did not deploy. the vehicle was taken to an authorized dealer where it was repaired. the dealer stated that the impact did not warrrant air bag deployment. a police report was filed. the failure mileage was approximately 70,000. .Vehicle was involved in a crash. Mileage was 70000 miles. Vehicle Identification Number (VIN):1YVHP80C385. Mazda Mazda6 2008 problem was reported in TOLEDO, OH. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Mazda Mazda6 2008 Fuel System, Gasoline

Mazda Mazda6 2008 Fuel System, Gasoline Review #10386349

MAZDA MAZDA6 2008 car safety problem was reported on Dec 15, 2009.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with FUEL SYSTEM, GASOLINE . tl* the contact owns a 2008 mazda mazda6. while driving approximately 30 mph, the contact noticed a yellow spider coming from the vent area onto the carpet. the contact stated she had noticed spiders in this area several times. the vehicle was not taken to the dealer for the failure. the contact referenced nhtsa campaign id number: 11v134000 (fuel system, gasoline: storage: tank assembly) which stated that a certain type of spider could weave a web in the evaporative canister vent line and potentially cause a restriction in the line. the manufacturer advised that the recall was only for the 2009-2010 model mazda6. the failure mileage 36,000 and the current mileage was 48,000. .Mileage was 36000 miles. Vehicle Identification Number (VIN):1YVHP80C285. Mazda Mazda6 2008 problem was reported in THORNTON, CO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Mazda Mazda6 2008 Unknown Or Other

Mazda Mazda6 2008 Unknown Or Other Review #10386412

MAZDA MAZDA6 2008 car safety problem was reported on Mar 03, 2011.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with UNKNOWN OR OTHER . yesterday i found a yellow sac spider in my 2008 4 cylinder mazda 6. *tr.Mileage was 52000 miles. Mazda Mazda6 2008 problem was reported in PEARL, MS. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. VEHICLE SPEED: 0 mph.

Mazda Mazda6 2008 Structure

Mazda Mazda6 2008 Structure Review #10395743

MAZDA MAZDA6 2008 car safety problem was reported on Apr 07, 2011.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with STRUCTURE . tl*the contact owns a 2008 mazda 6. the contact stated, the two engine mount bolts broke in half, causing the engine to fall and break the axle shaft and the valve cover gaskets. the dealer stated that it was normal for the 2008 mazda3. the contact stated there was some vibration coming from the steering prior to the failure, but though it was an alignment issue. the vehicle was repaired and the vibration ceased. the failure and current mileages were 64,000. updated 05/05/11*lj the consumer stated two cradle bolts and five engine mount bolts were replaced. updated 11/23/11.Mileage was 64000 miles. Vehicle Identification Number (VIN):1YVHP80C885. Mazda Mazda6 2008 problem was reported in AKRON, OH. Vehicle was purchased on Sept 22, 2009. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Mazda Mazda6 2008 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Mazda Mazda6 2008 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph. DEALER'S NAME: DAVE WALTER . DEALER'S TELEPHONE NUMBER: 330-434-8989 .

Mazda Mazda6 2008 Electrical System Battery Cables

Mazda Mazda6 2008 Electrical System Battery Cables Review #10452313

MAZDA MAZDA6 2008 car safety problem was reported on Mar 18, 2012.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with ELECTRICAL SYSTEM:BATTERY:CABLES . i tried to start my car on sunday morning (march 18th) and it would not start. i purchased a new battery. when i went to install it, i noted that the positive cable had corroded to the point where it could no longer make contact with the battery terminal. apparently, the wiring needs to be replaced at a cost of approximately $400. why would this happen at only 39,000 miles? i'm still working through this with the dealer, but wanted to post something as it appears others have had the same issue. i'm definitely not a mechanic but it appears that people might be having problems starting their car, or with batteries needing to be replaced pre-maturely and not realizing that it's due to corroded cables. *js.Mileage was 38500 miles. Vehicle Identification Number (VIN):1YVHP81C885. Mazda Mazda6 2008 problem was reported in TAMPA, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda6 2008 drive type:FWD. FUEL TYPE: GAS.

Mazda Mazda6 2008 Wheels

Mazda Mazda6 2008 Wheels Review #10457113

MAZDA MAZDA6 2008 car safety problem was reported on Apr 16, 2012.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . mazda 6i 2008 has two tire sensors fail, which appear to be defective in nature due to how low the mileage is. the tire sensor for right front passenger tire and a tire sensor for rear right passenger tire have failed and there is not even 36,000 miles on the car. was told this is not covered under warranty but this is a defective product that could result in an accident if the sensor fails while driving. there are many complaints on line regarding the mazda 6, the tire sensors should be recalled and replaced by mazda. *js.Mileage was 35249 miles. Vehicle Identification Number (VIN):1YVHP84C285. Mazda Mazda6 2008 problem was reported in OCEANPORT, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda6 2008 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS.

Mazda Mazda6 2008 Steering

Mazda Mazda6 2008 Steering Review #10464608

MAZDA MAZDA6 2008 car safety problem was reported on Feb 04, 2008.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with STEERING . when i purchase my new mazda 6, it was determined on a computer that the steering wheel was crooked, but the car was not out of alignment. then the car started pulling hard to the right. then the steering wheel started clunking when i was turning either way. after many trips to the service dept, a new steering column was put in. the clunking stopped, but the car would still pull hard to the right, and every time i got new tires or rotated the tires, the steering wheel would be crooked again, but not out of alignment. the clunking started again, and appears to have the same issue, but my car is out of warranty now and the dealership has changed owners 3 times. i feel my car was a lemon and i could not get help because the dealership kept being sold. i feel i am driving an unsafe car. i have never known anyone who had to have a steering column replaced. i am afraid that my car is going to pull me off the road into a tree. it is a 5-speed so 1 hand is off the steering wheel frequently. i need help from mazda to help me cure this problem because i am so frustrated in dealing with the dealerships. i am afraid that i am going to killed in this car because of the steering issue that is unresolved. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 1000 miles. Vehicle Identification Number (VIN):1YVHP80C185. Mazda Mazda6 2008 problem was reported in INDIANAPOLIS, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph.

Mazda Mazda6 2008 Tires Pressure Monitoring And Regulating Systems

Mazda Mazda6 2008 Tires Pressure Monitoring And Regulating Systems Review #10475924

MAZDA MAZDA6 2008 car safety problem was reported on Sept 17, 2012.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS . in one month i have had to replace 2 tire pressure sensors. when i asked about why these are going out they told me that there have been a lot of issues with the ones on my car, which is why mazda has since changed to a different sensor. the first one was a slow leak and i would have to fill it every few days,which although a huge pain, made it to where i could wait to bring it in when i had time to be car less for a few hours. the most recent one happened two days ago.i got home from one job at11 pm. the tire pressure light came on my drive home and i was thinking i was having problems again with the first one. i woke up at 7am to go to my other job and as i was driving there my car was very jerky so i pulled over at the gas station right by my house to check on my tire and it was completely flat .i went from close to full pressure to 0 in 8hours.this is very dangerous and a huge safety issue! if i had been out farther in the country or on a long car ride or if i hadn't noticed it was not steering correctly, this could have easily caused an accident. if i was pretty much told that the part was faulty at the dealership and it was known to leak then this should be recalled before someone gets hurt or worse. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 51000 miles. Mazda Mazda6 2008 problem was reported in LAKEVILLE, MN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 50 mph.

Mazda Mazda6 2008 Engine

Mazda Mazda6 2008 Engine Review #10495155

MAZDA MAZDA6 2008 car safety problem was reported on Dec 12, 2012.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with ENGINE . i was going down the i-90 in new york. i just got off a exit and notice my clutch was slipping so i stop and check my slave cylinder and it was cover in oil. i proceed to my destination and park i got out and look some more and notice oil running out of my bell housing. had it towed to a garage and check out they told me the rear main seal is gone and need to be replace. they also told me that the crankshaft had a lot of play in it side to side i also google this problem more than one person has this problem with low miles. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 71568 miles. Vehicle Identification Number (VIN):1YVHP80C485. Mazda Mazda6 2008 problem was reported in JOHNSTOWN, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda6 2008 Power Train

Mazda Mazda6 2008 Power Train Review #10495155

MAZDA MAZDA6 2008 car safety problem was reported on Dec 12, 2012.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . i was going down the i-90 in new york. i just got off a exit and notice my clutch was slipping so i stop and check my slave cylinder and it was cover in oil. i proceed to my destination and park i got out and look some more and notice oil running out of my bell housing. had it towed to a garage and check out they told me the rear main seal is gone and need to be replace. they also told me that the crankshaft had a lot of play in it side to side i also google this problem more than one person has this problem with low miles. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 71568 miles. Vehicle Identification Number (VIN):1YVHP80C485. Mazda Mazda6 2008 problem was reported in JOHNSTOWN, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda6 2008 Power Train Review #10497744

MAZDA MAZDA6 2008 car safety problem was reported on Sept 03, 2012.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . when the car is accelerating shift shock occurs when shifting from gear 3 to 4. it doesn't always occur when the transmission is cold, but is inevitable as the transmission warms. as time goes on the shift shock occurs under less and less of a load due to the wearing of a part in the transmission. the only way to fix the issue is to purchase a new transmission. when purchasing the transmission you have to make sure you get a transmission that has been redesigned, otherwise the issue will happen again. we talked to a mazda master mechanic that said mazda knows about the issue and even went as far as changing the way the transmission was made so the problem wouldn't continue. they obviously know the issue is their fault if they changed the design of the transmission, but will not issue a recall and own up to their mistake. from what we understand, the problem is with the housing of the transmission. this means you have no choice but the replace the entire transmission. mazda made a mistake in their engineering, but will not admit the mistake. we may not buy another mazda because of this. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 61000 miles. Vehicle Identification Number (VIN):1YVHP80C385. Mazda Mazda6 2008 problem was reported in DELAWARE, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Mazda Mazda6 2008 Power Train Review #10533325

MAZDA MAZDA6 2008 car safety problem was reported on July 15, 2013.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . i took my car to the mazda dealership after having experienced the 'at' light come on and a jolting in shifting gears and a real " drag" when trying to accelerate. i was told that the following fault codes "'torque converter clutch pressure control solenoid intermittent" and "transmission fluid pressure sensor/switch" indicate that i need a new transmission. i called the manufacturer because i was shocked that i would need a new transmission for a 5 year old car. i only average 12,500 miles per year, have had regular maintenance, have never heard of a transmission breaking down on such a " young" car. i believe they built the car with a poor quality product and now they will not take responsibility for it. even prior to the current mileage i had noticed that the car was jerky and "bucks" and not powerful when accelerating but i chalked it up to it being a 4 cylinder car-- prior to this vehicle i had owned 6 cylinder vehicles-- so i didn't know that perhaps these things were an indication of a failing transmission. i tried to explain to the dealership that i felt that mazda may have a faulty/ cheap transmission and i should not be responsible for a new transmission but they would not hear me out. a transmission should not break down after only 5 years. my previous cars lasted until 120,000 -150,000 without major breakdowns. i am livid and i feel i have no recourse. i hope someone investigates this matter. what a huge let down!!! there is no " zoom zoom" in this car. what a farce!!!!! i don't know how i will pay for this. i can't be the only one complaining of this issue. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 89000 miles. Vehicle Identification Number (VIN):1YVHP80C685. Mazda Mazda6 2008 problem was reported in MIDDLEBURG HTS, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 25 mph.

Mazda Mazda6 2008 Engine And Engine Cooling

Mazda Mazda6 2008 Engine And Engine Cooling Review #10563406

MAZDA MAZDA6 2008 car safety problem was reported on Feb 18, 2013.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with ENGINE AND ENGINE COOLING . the exhaust gaskets in this model fail leading to very loud noises from the engine which then leads to terrible emissions and failure of exhaust system. i looked the issue up online (and on this site) and found a tsb (01-024/07) that covered what i thought was the issue. this tsb said that the gasket between the exhaust manifold and cat was causing the noise. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 42000 miles. Vehicle Identification Number (VIN):1YVHP80C785. Mazda Mazda6 2008 problem was reported in ANNANDALE, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda6 2008 Structure Body

Mazda Mazda6 2008 Structure Body Review #10577914

MAZDA MAZDA6 2008 car safety problem was reported on Feb 05, 2014.MAZDA MAZDA6 2008, manufactured by MAZDA MOTOR CORP had a problem with STRUCTURE:BODY . tl* the contact owns a 2008 mazda mazda6. the contact stated that spiders somehow entered the dashboard area and that she saw several spiders coming out of the dashboard. the vehicle was not inspected by a dealer. the manufacturer was made aware of the failure. the vehicle was not repaired. the failure and current mileage was 90,000. .0 person(s) were injured. 0 person(s) died.Mileage was 90000 miles. Vehicle Identification Number (VIN):1YVHP80C185. Mazda Mazda6 2008 problem was reported in PITTSBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda6 2008 Steering

Mazda Mazda6 2008 Steering Review #10621760

MAZDA MAZDA6 2008 car safety problem was reported on Apr 08, 2008.MAZDA MAZDA6 2008, manufactured by Mazda Motor Corp. had a problem with STEERING . the car would make horrible sounds when i was turning left or right and would pull me to the left or right without me being able to conrol the car. a new steering column was put in by the dealership. the service manager at tom wood mazda (he now works at tom wood ford) said the car was designed to pull me off the highway or road in case i passed out at the wheel. then a new dealership bought the dealership and they replaced my steering column. my steering wheel was never straight, but the car was not out of alignment on a machine..0 person(s) were injured. 0 person(s) died.Mileage was 5000 miles. Vehicle Identification Number (VIN):1YVHP80C185. Mazda Mazda6 2008 problem was reported in INDIANAPOLIS, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 50 mph.

Mazda Mazda6 2008 Power Train

Mazda Mazda6 2008 Power Train Review #10621764

MAZDA MAZDA6 2008 car safety problem was reported on Aug 10, 2009.MAZDA MAZDA6 2008, manufactured by Mazda Motor Corp. had a problem with POWER TRAIN . my clutch started to get stiff and i couldn't push it. eventually the clutch plate fell apart and the fell through the body of the car. then that clutch plate fell apart. then i got a whole new clutch on 6/7/2013 and it felt bad but the dealership said "it's a self-adjusting clutch, it will loosen up over time." then in may 2014, the noise came back and i could barely push the clutch peddle again so i took it and they said it needed a clutch master and a clutch slave but it made it worse and the car made a horrible sound after they put those parts in, so they said the entire clutch was bad and they'd replace it under warranty, but the noise didn't go away so they said i needed a whole new engine. their faulty clutch blew up my entire engine because the gears were slipping. so a great car had a blown engine because of a faulty clutch..0 person(s) were injured. 0 person(s) died.Mileage was 20000 miles. Vehicle Identification Number (VIN):1YVHP80C185. Mazda Mazda6 2008 problem was reported in INDIANAPOLIS, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 25 mph.

Mazda Mazda6 2008 Engine

Mazda Mazda6 2008 Engine Review #10621764

MAZDA MAZDA6 2008 car safety problem was reported on Aug 10, 2009.MAZDA MAZDA6 2008, manufactured by Mazda Motor Corp. had a problem with ENGINE . my clutch started to get stiff and i couldn't push it. eventually the clutch plate fell apart and the fell through the body of the car. then that clutch plate fell apart. then i got a whole new clutch on 6/7/2013 and it felt bad but the dealership said "it's a self-adjusting clutch, it will loosen up over time." then in may 2014, the noise came back and i could barely push the clutch peddle again so i took it and they said it needed a clutch master and a clutch slave but it made it worse and the car made a horrible sound after they put those parts in, so they said the entire clutch was bad and they'd replace it under warranty, but the noise didn't go away so they said i needed a whole new engine. their faulty clutch blew up my entire engine because the gears were slipping. so a great car had a blown engine because of a faulty clutch..0 person(s) were injured. 0 person(s) died.Mileage was 20000 miles. Vehicle Identification Number (VIN):1YVHP80C185. Mazda Mazda6 2008 problem was reported in INDIANAPOLIS, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 25 mph.

Air Bags 2 Review(s)

Air Bags Side/window 1 Review(s)

Electrical System 3 Review(s)

Electrical System Battery Cables 1 Review(s)

Engine 2 Review(s)

Engine And Engine Cooling 1 Review(s)

Engine And Engine Cooling Engine 1 Review(s)

Fuel System, Diesel 1 Review(s)

Fuel System, Gasoline 3 Review(s)

Power Train 5 Review(s)

Power Train Manual Transmission 1 Review(s)

Seat Belts 1 Review(s)

Service Brakes, Hydraulic 2 Review(s)

Service Brakes, Hydraulic Foundation Components Disc Rotor 1 Review(s)

Steering 3 Review(s)

Structure 1 Review(s)

Structure Body 1 Review(s)

Tires Pressure Monitoring And Regulating Systems 1 Review(s)

Unknown Or Other 1 Review(s)

Visibility 1 Review(s)

Visibility Windshield Wiper/washer 1 Review(s)

Wheels 1 Review(s)