Car-and-Safety.com

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10283908

MAZDA MAZDA3 2010 car safety problem was reported on Aug 30, 2009.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . driver seat feels loose and rocks back and forth while i am driving vehicle. i am concerned seat will not hold up in accident. sat in similar car at dealer with same problem. *tr.Vehicle Identification Number (VIN):JM1BL1S67A1. Mazda Mazda3 2010 problem was reported in LA MESA, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility Rearview Mirrors/devices

Mazda Mazda3 2010 Visibility Rearview Mirrors/devices Review #10295772

MAZDA MAZDA3 2010 car safety problem was reported on Dec 07, 2009.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with VISIBILITY:REARVIEW MIRRORS/DEVICES . i was adjusting my rear view mirror on my new 2010 mazda 3 and it came off. when it came off it broke off a chunk of glass from the windshield. mazda refuses to repair the problem! *tr.Mileage was 3500 miles. Mazda Mazda3 2010 problem was reported in TEQUESTA, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Visibility Review #10296113

MAZDA MAZDA3 2010 car safety problem was reported on Dec 16, 2009.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with VISIBILITY . rear glass explosion on 2010 mazda 3 sedan. morning 16 degrees f. approached my car in the morning and heard a crackling noise. i thought the sound was ice. i started the car and the rear defogger. as i sat in my driveway ...approximately 30 seconds after turning on the defogger. the rear glass exploded with a load noise. glass was thrown into the rear passenger seats. the car is 4 months old and under warranty. i took the car to the dealer and they would not repair under warranty. i called mazda customer care at 1-800-222-5500 and was told that this is due to outside influence (ie the same as if a tree branch fell on the car). he indicated that i should expect that this could happen in the cold weather. i can not believe that i should expect that my rear window can explode in cold weather. if my children were in the rear seat they would have been potentially seriously injured by thrown glass. *tr.Mileage was 10048 miles. Vehicle Identification Number (VIN):JM1BL1SF1A1. Mazda Mazda3 2010 problem was reported in BELLBROOK, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Fuel System, Gasoline

Mazda Mazda3 2010 Fuel System, Gasoline Review #10297916

MAZDA MAZDA3 2010 car safety problem was reported on Jan 02, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with FUEL SYSTEM, GASOLINE . 2010 mazda 3, 5 speed. upon shifting from 4th gear into neutral, to prepare for a stop, foot was taken off of accelerator and clutch was fully released; the engine started to rev. this is the 3rd time this has happened in 90 days. each time has been when the vehicle was shifted into neutral from a gear, not gear specific. *tr.Mileage was 13345 miles. Vehicle Identification Number (VIN):JM1BL1SF8A1. Mazda Mazda3 2010 problem was reported in LAS CRUCES, NM. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Mazda Mazda3 2010 Structure Body

Mazda Mazda3 2010 Structure Body Review #10312433

MAZDA MAZDA3 2010 car safety problem was reported on July 15, 2009.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with STRUCTURE:BODY . (2010 mazda3 5-dr with sunroof) when sunroof is fully opened and driving around 35 miles/hr, complete roof starts to vibrate producing loud noise. i took the car to a car dealer and technician noticed the problem as well. i was told that the car is new design and that mazda engineering received a complain. no action taken but advised to purchase a wind deflector. the vibration happens every time i open the sunroof. *tr.Mileage was 300 miles. Vehicle Identification Number (VIN):JM1BL1H66A1. Mazda Mazda3 2010 problem was reported in NORTH BRUNSWICK, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Mazda Mazda3 2010 Latches/locks/linkages

Mazda Mazda3 2010 Latches/locks/linkages Review #10312518

MAZDA MAZDA3 2010 car safety problem was reported on Feb 20, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with LATCHES/LOCKS/LINKAGES . mazda 3 2010 front doors locked and would not unlock-not with key and not from inside car- *tr.Mileage was 4000 miles. Vehicle Identification Number (VIN):JM1BL1SG6A1. Mazda Mazda3 2010 problem was reported in HAUPPAUGE, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Fuel System, Gasoline

Mazda Mazda3 2010 Fuel System, Gasoline Review #10328438

MAZDA MAZDA3 2010 car safety problem was reported on Apr 24, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with FUEL SYSTEM, GASOLINE . while driving slowly through a community center parking lot, the automobile suddenly accelerated and did not respond to braking,resulting in a crash into a brick wall. *tr.Vehicle was involved in a crash. 1 person(s) were injured. 0 person(s) died.Mileage was 1260 miles. Vehicle Identification Number (VIN):JM1BL1H69A1. Mazda Mazda3 2010 problem was reported in ARLINGTON, VA. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 5 mph.

Mazda Mazda3 2010 Vehicle Speed Control

Mazda Mazda3 2010 Vehicle Speed Control Review #10328438

MAZDA MAZDA3 2010 car safety problem was reported on Apr 24, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with VEHICLE SPEED CONTROL . while driving slowly through a community center parking lot, the automobile suddenly accelerated and did not respond to braking,resulting in a crash into a brick wall. *tr.Vehicle was involved in a crash. 1 person(s) were injured. 0 person(s) died.Mileage was 1260 miles. Vehicle Identification Number (VIN):JM1BL1H69A1. Mazda Mazda3 2010 problem was reported in ARLINGTON, VA. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 5 mph.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10329330

MAZDA MAZDA3 2010 car safety problem was reported on May 07, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . 2010 mazda 3 excessive tire wear. bought car new in oct 2009. may 7th 2010 the car has 18,000 miles on it and the rear tires are down to the steel belts. my net searching shows this is a very common problem. how a car can have only 18,000 miles on it and have dangerously worn tires is beyond belief. the dealership considers this "normal on mazda 3's". tires were well maintained with tire pressure by me. my car has never been in an accident or hit a significant road hazard. car is used for mostly straight line highway driving. *tr.Mileage was 18000 miles. Mazda Mazda3 2010 problem was reported in STROUDSBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Engine And Engine Cooling

Mazda Mazda3 2010 Engine And Engine Cooling Review #10331059

MAZDA MAZDA3 2010 car safety problem was reported on Apr 15, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ENGINE AND ENGINE COOLING . smoke came threw the vents of the 2010 mazda3 hatchback and then from under the hood. then flames came out from hood. it burned until the fire department put it out. it was not able to be repaired. *tr.Vehicle was on fire. Mileage was 3500 miles. Vehicle Identification Number (VIN):JM1BL1H51A1. Mazda Mazda3 2010 problem was reported in CHICAGO, IL. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 5 mph.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10332543

MAZDA MAZDA3 2010 car safety problem was reported on May 20, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . tl* the contact owns a 2010 mazda 3. the contact stated while traveling at approximate speeds of 65 mph, the right passenger tire blew out. the contact was able to install the spare tire and drove to a tire facility. the manufacturer of the tires advised the failure was caused by a defect and offered to take liability for 50 percent of the replacement tire. the failure mileage was approximately 700 and the current mileage was approximately 850. updated 08/03/10. *lj updated 08/04/10*jb .Mileage was 700 miles. Vehicle Identification Number (VIN):JM1BL1S6XA1. Mazda Mazda3 2010 problem was reported in MARIETTA, CA. Vehicle was purchased on Apr 01, 2010. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Mazda Mazda3 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 65 mph. DEALER'S NAME: MAZDA OF TEMECULA .

Mazda Mazda3 2010 Air Bags

Mazda Mazda3 2010 Air Bags Review #10340399

MAZDA MAZDA3 2010 car safety problem was reported on May 26, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with AIR BAGS . tl* the contact owns a 2010 mazda, mazda 3. while traveling at 35 mph, the air bag warning light illuminated. the dealer rewired the air bag connection to correct the failure. the failure mileage was 17,000 and the current mileage was 19,000. .Mileage was 17000 miles. Vehicle Identification Number (VIN):JM1BL1SFXA1. Mazda Mazda3 2010 problem was reported in FAIRFAX, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Mazda Mazda3 2010 Steering

Mazda Mazda3 2010 Steering Review #10342587

MAZDA MAZDA3 2010 car safety problem was reported on July 08, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with STEERING . car failed to start. mazda sent tow truck. tow truck operator was able to start the car in neutral. tow truck operator declined to tow the car and sent driver home. later that day the wheel locked, power brakes failed and driver rolled into a ditch. driver turned off ignition, unlocked steering wheel, backed car out of ditch and called mazda for another tow. the consumer stated the day of delivery, the salesman had trouble starting the car and requested a technician make some adjustment to the ignition. the wheel locked and the key would not start the vehicle. after the adjustments, the vehicle appeared to work fine. the dealer stated the vehicle would not start because a cable was bent, which was prohibiting the vehicle from being recognized in park when attempting to start it. updated ivoq 08/19/10*jb updated ivoq 08/20/10*jb *tr.Vehicle was involved in a crash. Mileage was 1000 miles. Vehicle Identification Number (VIN):JM1BL1SF2A1. Mazda Mazda3 2010 problem was reported in DUNWOODY, GA. Vehicle was purchased on June 19, 2010. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph. DEALER'S NAME: JIM ELLSI MAZDA . DEALER'S CITY: MARIETTA . DEALER'S STATE CODE: GA.

Mazda Mazda3 2010 Electrical System

Mazda Mazda3 2010 Electrical System Review #10342587

MAZDA MAZDA3 2010 car safety problem was reported on July 08, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ELECTRICAL SYSTEM . car failed to start. mazda sent tow truck. tow truck operator was able to start the car in neutral. tow truck operator declined to tow the car and sent driver home. later that day the wheel locked, power brakes failed and driver rolled into a ditch. driver turned off ignition, unlocked steering wheel, backed car out of ditch and called mazda for another tow. the consumer stated the day of delivery, the salesman had trouble starting the car and requested a technician make some adjustment to the ignition. the wheel locked and the key would not start the vehicle. after the adjustments, the vehicle appeared to work fine. the dealer stated the vehicle would not start because a cable was bent, which was prohibiting the vehicle from being recognized in park when attempting to start it. updated ivoq 08/19/10*jb updated ivoq 08/20/10*jb *tr.Vehicle was involved in a crash. Mileage was 1000 miles. Vehicle Identification Number (VIN):JM1BL1SF2A1. Mazda Mazda3 2010 problem was reported in DUNWOODY, GA. Vehicle was purchased on June 19, 2010. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph. DEALER'S NAME: JIM ELLSI MAZDA . DEALER'S CITY: MARIETTA . DEALER'S STATE CODE: GA.

Mazda Mazda3 2010 Air Bags

Mazda Mazda3 2010 Air Bags Review #10344230

MAZDA MAZDA3 2010 car safety problem was reported on June 13, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with AIR BAGS . the vehicle crashed into two cars and rolled over and none of the airbags were deployed including side, passenger and driver. *tr.Vehicle was involved in a crash. 1 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1S63A1. Mazda Mazda3 2010 problem was reported in PORTER RANCH, CA. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Steering

Mazda Mazda3 2010 Steering Review #10345067

MAZDA MAZDA3 2010 car safety problem was reported on Mar 06, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with STEERING . intermittent failure of power steering pump while driving in a straight line and when turning. small corrections are needed to maintain travel within a lane and when turning you can feel the power assistance drop in and out giving a jerky feel. this was a rental vehicle. *tr.Mileage was 109 miles. Vehicle Identification Number (VIN):JM1BL1SF3A1. Mazda Mazda3 2010 problem was reported in STOCKTON, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 20 mph.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10345310

MAZDA MAZDA3 2010 car safety problem was reported on July 26, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . 2010 mazda 3 excessive tire wear. bought car new in sept 2009. july 2010 the car has 24,000 miles on it and all tires are worn out in patches and alignment needs to be done on all wheels. ken towery considers this "normal on mazda 3's". i use my car for commuting so mostly highway driving. *tr.Mileage was 24000 miles. Vehicle Identification Number (VIN):JM1BL1H52A1. Mazda Mazda3 2010 problem was reported in LOUISVILLE, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Steering

Mazda Mazda3 2010 Steering Review #10348712

MAZDA MAZDA3 2010 car safety problem was reported on Aug 09, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with STEERING . loss of steering control on my 2010 mazda 3 resulting in accident. also the brakes did not operate as designed. while turning a corner the vehicle steering wheel locked and/or loss steering control , brakes were applied, vehicle begin to stop but before stopping, it turned and ran off the road causing damage to vehicle and property. this was confirmed by driver, 2 passengers and the police. this was the first time this happened. not sure what is wrong with vehicle. damaged being repaired at this time. *tr.Vehicle was involved in a crash. Mileage was 1900 miles. Vehicle Identification Number (VIN):JM1BL1SF2A1. Mazda Mazda3 2010 problem was reported in NAPLES, FL. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 20 mph.

Mazda Mazda3 2010 Air Bags Frontal Sensor/control Module

Mazda Mazda3 2010 Air Bags Frontal Sensor/control Module Review #10357985

MAZDA MAZDA3 2010 car safety problem was reported on July 15, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE . tl*the contact owns a 2010 mazda 3. the contact stated that the air bag warning light illuminated upon starting the vehicle although a passenger was seated in the front passenger seat. the failure occurred intermittently. the vehicle was taken to an authorized dealer where the front passenger seat weight sensor was repaired. the failure continued and the vehicle was taken back to the dealership where the contact was told that the vehicle was functioning as designed. the vehicle had not been repaired again. the failure mileage was 3,500 and the current mileage was approximately 7,900. updated 01/06/11 *bf updated 01/24/11/*jb.Mileage was 3500 miles. Vehicle Identification Number (VIN):JM1BL1H50A1. Mazda Mazda3 2010 problem was reported in SANDY SPRINGS, GA. Original Owner. Vehicle was purchased on Apr 03, 2010. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Mazda Mazda3 2010 TRANSMISSION TYPE: MAN . VEHICLE SPEED: 0 mph. DEALER'S NAME: JIM ELLIS MAZDA . DEALER'S TELEPHONE NUMBER: 770-590-4450 . DEALER'S CITY: MARIETTA . DEALER'S STATE CODE: GA. DEALER'S ZIPCODE: 30060 .

Mazda Mazda3 2010 Power Train Manual Transmission

Mazda Mazda3 2010 Power Train Manual Transmission Review #10361554

MAZDA MAZDA3 2010 car safety problem was reported on Oct 15, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN:MANUAL TRANSMISSION . 2011 mazda speed3. new off the lot and clutch fails in 30 miles...same day! after "repair", clutch again fails next day, ~120 miles. 2 clutch failures in 2 days of use, ~150 miles. failed while driving. dealer/mazda claim "wear" item...our fault! fighting via lemon law and mechantability. *tr.Mileage was 30 miles. Mazda Mazda3 2010 problem was reported in VENTURA, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 10 mph.

Mazda Mazda3 2010 Vehicle Speed Control

Mazda Mazda3 2010 Vehicle Speed Control Review #10362303

MAZDA MAZDA3 2010 car safety problem was reported on June 03, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with VEHICLE SPEED CONTROL . i was stopped with the car running in drive and stepping on the brake pedal only, when the engine began revving uncontrollably. this resulted in increasingly high rpms, and it felt as if the car was about to lurch forward. i ended up turning off the car, and re-starting it. this is an intermittent problem that has happened a total of 3 times, each time while in a stopped position. i purchased the car the end of march 2010. first occurrence happened prior to 6/3/10, and the third, most recent occurrence, happened on 8/26/10. mazda has installed a data recorder to attempt to record the problem, but now they want to remove it before the problem has re-occurred. *tr.Mileage was 1800 miles. Vehicle Identification Number (VIN):JM1BL1SG0A1. Mazda Mazda3 2010 problem was reported in SEATTLE, WA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Vehicle Speed Control Review #10363675

MAZDA MAZDA3 2010 car safety problem was reported on Oct 29, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with VEHICLE SPEED CONTROL . cruise control turns off when going down hills, even small ones. i use my cruise control daily and my drive to work contains many small hills. when cruising at 70, i go down a hill. the cruise control backs off then at the bottom of the hill, it fails to engage. once i have drifted from 70 mph down to 60 mph, it turns itself off. i've had my car 2 months and this has happened 11 times now. the dealership claims there isn't anything wrong and the only way it can turn itself off is if i touch the brake or the clutch. i am doing neither. when on a busy highway, and this begins to happen, the people behind you get very angry. beside the fact i have begun slowing down without my brake lights coming on. there are others with the same problem here http://mazda3revolution.com/forums/2010-mazdaspeed-3-news-discussion/2758-anyone-having-cruise-control-issues.html. *tr.Mileage was 4500 miles. Vehicle Identification Number (VIN):JM1BL1H37A1. Mazda Mazda3 2010 problem was reported in LAWNDALE, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 70 mph.

Mazda Mazda3 2010 Steering

Mazda Mazda3 2010 Steering Review #10364033

MAZDA MAZDA3 2010 car safety problem was reported on July 10, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with STEERING . tl*the contact owns a 2010 mazda3. while driving 65 mph the vehicle lost power within a few seconds and the power steering light illuminated. the steering failed and the contact experienced electrical failure with the passenger door that could not be unlocked from the inside. the sunroof button also would not shut the sunroof. the vehicle was taken to the dealer for diagnostic testing who was unable to locate a failure code; therefore, they stated that nothing was wrong with the vehicle. the manufacturer took report number 132669400. the failure mileage was 13,800. the current mileage was 13,900. .Mileage was 13800 miles. Vehicle Identification Number (VIN):JM1BL1H6XA1. Mazda Mazda3 2010 problem was reported in PROVIDENCE, RI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Mazda Mazda3 2010 Latches/locks/linkages

Mazda Mazda3 2010 Latches/locks/linkages Review #10364033

MAZDA MAZDA3 2010 car safety problem was reported on July 10, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with LATCHES/LOCKS/LINKAGES . tl*the contact owns a 2010 mazda3. while driving 65 mph the vehicle lost power within a few seconds and the power steering light illuminated. the steering failed and the contact experienced electrical failure with the passenger door that could not be unlocked from the inside. the sunroof button also would not shut the sunroof. the vehicle was taken to the dealer for diagnostic testing who was unable to locate a failure code; therefore, they stated that nothing was wrong with the vehicle. the manufacturer took report number 132669400. the failure mileage was 13,800. the current mileage was 13,900. .Mileage was 13800 miles. Vehicle Identification Number (VIN):JM1BL1H6XA1. Mazda Mazda3 2010 problem was reported in PROVIDENCE, RI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Mazda Mazda3 2010 Visibility Sun Roof Assembly

Mazda Mazda3 2010 Visibility Sun Roof Assembly Review #10364033

MAZDA MAZDA3 2010 car safety problem was reported on July 10, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with VISIBILITY:SUN ROOF ASSEMBLY . tl*the contact owns a 2010 mazda3. while driving 65 mph the vehicle lost power within a few seconds and the power steering light illuminated. the steering failed and the contact experienced electrical failure with the passenger door that could not be unlocked from the inside. the sunroof button also would not shut the sunroof. the vehicle was taken to the dealer for diagnostic testing who was unable to locate a failure code; therefore, they stated that nothing was wrong with the vehicle. the manufacturer took report number 132669400. the failure mileage was 13,800. the current mileage was 13,900. .Mileage was 13800 miles. Vehicle Identification Number (VIN):JM1BL1H6XA1. Mazda Mazda3 2010 problem was reported in PROVIDENCE, RI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Mazda Mazda3 2010 Steering

Mazda Mazda3 2010 Steering Review #10365005

MAZDA MAZDA3 2010 car safety problem was reported on Nov 04, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with STEERING . on 11/4, i was on my way to meet my yoga classmate for lunch at 1917 bistro. the restaurant�s parking lot was full. so, i backed out and circled the block to find another parking space. when driving on livernois i noticed a parking lot that�s why i decided to go back around. i pulled into the first empty parking lot which i thought was better than trying to parallel parking in the one space on the street. so, i turned into a graveled parking lot. i made a left then began to pull up to the parking space but the car accelerated and smashed into a building. the car would not stop so i shifted the car into reverse. the car jerked back wildly; it was hard to handle but i got the car to stop. a man came out of the wig shop. i was standing outside of the car examining the damage - white paint from the building and a slight puck on both sides of the bumper. the man looked at me incredulously because he said the impact shook theshop . his mouth was open and it took him a few minutes to close it. a woman came out also because she felt the impact in the shop next to the man's shop. there were no witnesses to my acceleration problem. i did not report the incident because i did not see a police officer (it's detroit). after lunch, i drove back home and sent mazda an email. i heard from mazda friday morning. the car was towed to the dealer in troy. i spoke to amir about the incident and told him that the car was on its way into the dealership (by the way, i even have my oil change at the dealership). when the car arrived i received a call from scott bryant who, in an accusatory manner asked me to repeat what happened despite amir telling him my story. he warned me that it will take all afternoon to look at the car. scott called later to inform me that a field engineer will be coming in on monday to look at the car. he did not offer me a rental. *tr.Vehicle was involved in a crash. Mileage was 49000 miles. Vehicle Identification Number (VIN):JM1BK343671. Mazda Mazda3 2010 problem was reported in DETROIT, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. VEHICLE SPEED: 5 mph.

Mazda Mazda3 2010 Vehicle Speed Control

Mazda Mazda3 2010 Vehicle Speed Control Review #10365005

MAZDA MAZDA3 2010 car safety problem was reported on Nov 04, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with VEHICLE SPEED CONTROL . on 11/4, i was on my way to meet my yoga classmate for lunch at 1917 bistro. the restaurant�s parking lot was full. so, i backed out and circled the block to find another parking space. when driving on livernois i noticed a parking lot that�s why i decided to go back around. i pulled into the first empty parking lot which i thought was better than trying to parallel parking in the one space on the street. so, i turned into a graveled parking lot. i made a left then began to pull up to the parking space but the car accelerated and smashed into a building. the car would not stop so i shifted the car into reverse. the car jerked back wildly; it was hard to handle but i got the car to stop. a man came out of the wig shop. i was standing outside of the car examining the damage - white paint from the building and a slight puck on both sides of the bumper. the man looked at me incredulously because he said the impact shook theshop . his mouth was open and it took him a few minutes to close it. a woman came out also because she felt the impact in the shop next to the man's shop. there were no witnesses to my acceleration problem. i did not report the incident because i did not see a police officer (it's detroit). after lunch, i drove back home and sent mazda an email. i heard from mazda friday morning. the car was towed to the dealer in troy. i spoke to amir about the incident and told him that the car was on its way into the dealership (by the way, i even have my oil change at the dealership). when the car arrived i received a call from scott bryant who, in an accusatory manner asked me to repeat what happened despite amir telling him my story. he warned me that it will take all afternoon to look at the car. scott called later to inform me that a field engineer will be coming in on monday to look at the car. he did not offer me a rental. *tr.Vehicle was involved in a crash. Mileage was 49000 miles. Vehicle Identification Number (VIN):JM1BK343671. Mazda Mazda3 2010 problem was reported in DETROIT, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. VEHICLE SPEED: 5 mph.

Mazda Mazda3 2010 Fuel System, Gasoline

Mazda Mazda3 2010 Fuel System, Gasoline Review #10367388

MAZDA MAZDA3 2010 car safety problem was reported on Oct 07, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with FUEL SYSTEM, GASOLINE . mazda3 rear ended a moving truck. mazda3 was going about 45 mph and truck was not moving. upon impact, the mazda3 immediately caught fire at the front of the car. fire department had to extinguish fire. fire damaged car. car should not have caught fire..Vehicle was involved in a crash. Vehicle was on fire. 0 person(s) were injured. 0 person(s) died.Mileage was 20000 miles. Vehicle Identification Number (VIN):JM1BL1SF4A1. Mazda Mazda3 2010 problem was reported in ST. LOUIS, MO. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10367388

MAZDA MAZDA3 2010 car safety problem was reported on Oct 07, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with UNKNOWN OR OTHER . mazda3 rear ended a moving truck. mazda3 was going about 45 mph and truck was not moving. upon impact, the mazda3 immediately caught fire at the front of the car. fire department had to extinguish fire. fire damaged car. car should not have caught fire..Vehicle was involved in a crash. Vehicle was on fire. 0 person(s) were injured. 0 person(s) died.Mileage was 20000 miles. Vehicle Identification Number (VIN):JM1BL1SF4A1. Mazda Mazda3 2010 problem was reported in ST. LOUIS, MO. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Mazda Mazda3 2010 Power Train Clutch Assembly

Mazda Mazda3 2010 Power Train Clutch Assembly Review #10368669

MAZDA MAZDA3 2010 car safety problem was reported on Oct 30, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN:CLUTCH ASSEMBLY . tl* the contact owns a 2010 mazda mazda3. while driving approximately 60 mph, the contact engaged the clutch and felt an unusual pop under her foot. she stated that the vehicle exhibited an abnormal increase in engine rpms as if she were attempting to drive while in neutral. the vehicle was towed to an authorized dealer where the dealer advised her that the entire clutch would need replacing. the vehicle was repaired. she then contacted the manufacturer and was advised that the clutch was not under warranty and would provide no further assistance. the vehicle was not under recall. the failure mileage was 33,000 and the current mileage was 35,000..Mileage was 33000 miles. Vehicle Identification Number (VIN):JM1BL1SF7A1. Mazda Mazda3 2010 problem was reported in RIVERSIDE, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Mazda Mazda3 2010 Parking Brake

Mazda Mazda3 2010 Parking Brake Review #10368671

MAZDA MAZDA3 2010 car safety problem was reported on Nov 25, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with PARKING BRAKE . lifted parking brake lever to engage parking brake, and it came up way further than normal without offering the normal resistance. after three attempts at resetting the brake, it engaged normally. malfunction occurred again two days later, but this time, i could not get it to engage successfully even after multiple attempts. dealer diagnosed that the brake lever assembly was intermittently sticking and replaced lever assembly. two days later, same problem occurred again. car is 9 months old, 13,500 mi. *tr.Mileage was 13500 miles. Vehicle Identification Number (VIN):JM1BL1H52A1. Mazda Mazda3 2010 problem was reported in LOS LUNAS, NM. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Latches/locks/linkages

Mazda Mazda3 2010 Latches/locks/linkages Review #10370440

MAZDA MAZDA3 2010 car safety problem was reported on Apr 17, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with LATCHES/LOCKS/LINKAGES . tl*the contact owns a 2010 mazda 3. while the vehicle was parked, the contact attempted to unlock the front passenger door but it would not unlock with the remote or key. the vehicle was taken to an authorized dealer who repaired the lock. the failure occurred again on the driver side door. the vehicle was taken to an authorized dealer. the vin was unavailable. the failure mileage was approximately 15,000 and the current mileage was approximately 25,000..Mileage was 15000 miles. Mazda Mazda3 2010 problem was reported in COLUMBIA, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Service Brakes, Hydraulic

Mazda Mazda3 2010 Service Brakes, Hydraulic Review #10370910

MAZDA MAZDA3 2010 car safety problem was reported on Dec 15, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SERVICE BRAKES, HYDRAULIC . i lifted the emergency brake lever to engage the emergency brake and notice that the lever came up the whole way with very little resistance. i had no idea why this was happening. a few days later i realized that after the same issue had occurred there was white smoke coming out of the rear-left wheel brake pad. i took my car to a mazda dealer to have it serviced (since it's barely one year old), and they could not find any problems the first time around. i have done a little bit of searching on the internet and this is not the first time this same issue has happened. i would love to get some feedback from mazda since i almost got into a bad accident yesterday (dec 15) in atlanta due to icy roads and a faulty rear-left brake on a brand new car. *tr.Mazda Mazda3 2010 problem was reported in ATLANTA, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Power Train Driveline

Mazda Mazda3 2010 Power Train Driveline Review #10371142

MAZDA MAZDA3 2010 car safety problem was reported on Dec 15, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN:DRIVELINE . at 5000 miles clutch started to make squeaking sound and vibration when engaging. *tr.Mileage was 5000 miles. Mazda Mazda3 2010 problem was reported in BROOMALL, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Power Train Manual Transmission

Mazda Mazda3 2010 Power Train Manual Transmission Review #10371142

MAZDA MAZDA3 2010 car safety problem was reported on Dec 15, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN:MANUAL TRANSMISSION . at 5000 miles clutch started to make squeaking sound and vibration when engaging. *tr.Mileage was 5000 miles. Mazda Mazda3 2010 problem was reported in BROOMALL, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Power Train Review #10371142

MAZDA MAZDA3 2010 car safety problem was reported on Dec 15, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . at 5000 miles clutch started to make squeaking sound and vibration when engaging. *tr.Mileage was 5000 miles. Mazda Mazda3 2010 problem was reported in BROOMALL, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Engine And Engine Cooling

Mazda Mazda3 2010 Engine And Engine Cooling Review #10372271

MAZDA MAZDA3 2010 car safety problem was reported on Dec 01, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ENGINE AND ENGINE COOLING . tl*the contact owns a 2010 mazda mazda3. the vehicle was parked and turned on when it shut off for approximately five minutes. when the contact attempted to restart the vehicle it would not start. the vehicle was towed to an authorized dealer where they were unable to diagnosed the failure. the failure recurred four times. an authorized dealer was unable to diagnose the failure because the vehicle successfully started after being turned off for an extended period of time. the failure mileage was 14,000 and the current mileage was 14,700. .Mileage was 14000 miles. Vehicle Identification Number (VIN):JM1BL1S69A1. Mazda Mazda3 2010 problem was reported in INTERLACHEN, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Power Train Manual Transmission

Mazda Mazda3 2010 Power Train Manual Transmission Review #10372591

MAZDA MAZDA3 2010 car safety problem was reported on Dec 16, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN:MANUAL TRANSMISSION . i purchased my 2010 mazda 3 in august 2009. in december 2010, i was driving home from work and stopped at a red light. when the light turned green, i engaged the clutch and i felt a pop under my foot and the clutch became stuck. when it finally came back up it vibrated and jerked itself before going back to starting position. i put the car in first gear and attempted to accelerate. the car accelerated but the vehicle did not move. to see if the clutch was catching, i put the car in first gear and took my foot off the clutch without giving it gas. the car did not turn off as it normally would if i did not give it gas while in first gear. the clutch failed without warning at 20,100 miles. the vehicle was towed to an authorized dealer and i was advised that the entire clutch needed to be replaced and i might have to replace the flywheel. i was advised the clutch was considered a wear item and could not be replaced under warranty. however, due to the sudden and premature nature of the failure, i am speaking with mazda in an attempt to have the vehicle fixed under warranty. *tr.Mileage was 20100 miles. Vehicle Identification Number (VIN):JM1BL1SF3A1. Mazda Mazda3 2010 problem was reported in MIAMI SHORES, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10373115

MAZDA MAZDA3 2010 car safety problem was reported on Dec 20, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with UNKNOWN OR OTHER . a low speed rear-end collision resulted in an immediate explosion of the vehicle, causing a large external fire and smoke to enter the cabin upon impact. the structural damage to the vehicle occurred on the front-right; the fire destroyed the entire front 2/3 of the vehicle (totaling the vehicle). the concern is that such a low speed impact should not cause an explosion which could potentially have injured or killed the driver and passengers..Vehicle was involved in a crash. Vehicle was on fire. 0 person(s) were injured. 0 person(s) died.Mileage was 150 miles. Vehicle Identification Number (VIN):JM1BL1S6XA1. Mazda Mazda3 2010 problem was reported in WEST LINN, OR. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Mazda Mazda3 2010 Engine And Engine Cooling

Mazda Mazda3 2010 Engine And Engine Cooling Review #10375076

MAZDA MAZDA3 2010 car safety problem was reported on Dec 22, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ENGINE AND ENGINE COOLING . tl*the contact owns a 2010 mazda 3. the contact stated that while driving approximately 30 mph when the vehicle suddenly stalled causing him to loose control of his steering wheel and was also unable to apply the brakes. he then crashed into a mailbox and the side of a mountain. a police was filed. the driver was not injured after the crash. the vehicle was towed to an independent mechanic. the manufacturer was also contacted and informed him that they were aware of the failure in prior years, but not of the 2010 models. the failure mileage was approximately 6100. updated 03/03/11.Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Mileage was 6100 miles. Vehicle Identification Number (VIN):JM1BL1SG6A1. Mazda Mazda3 2010 problem was reported in LEMONT, PA. Accident was reported to Police. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Mazda Mazda3 2010 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 30 mph.

Mazda Mazda3 2010 Power Train Manual Transmission

Mazda Mazda3 2010 Power Train Manual Transmission Review #10375594

MAZDA MAZDA3 2010 car safety problem was reported on Jan 03, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN:MANUAL TRANSMISSION . i have a 2010 mazda 3 spor with 41,000 miles and the clutch totally went. clutch , flywheel had to be replaced for $1800 dollars. mazda refused to admit any defect. *tr.Mileage was 41000 miles. Mazda Mazda3 2010 problem was reported in WINDSOR, CT. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Engine And Engine Cooling

Mazda Mazda3 2010 Engine And Engine Cooling Review #10376702

MAZDA MAZDA3 2010 car safety problem was reported on Dec 22, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ENGINE AND ENGINE COOLING . on december 21, 2010 car stalled and lost steering and brake control on 12/22 happened again resulting in accident and $9,000 in damage. *tr.Vehicle was involved in a crash. Mileage was 6200 miles. Mazda Mazda3 2010 problem was reported in LEMONT, PA. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Mazda Mazda3 2010 Power Train

Mazda Mazda3 2010 Power Train Review #10381147

MAZDA MAZDA3 2010 car safety problem was reported on Feb 08, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . clutch malfunction says it's not defective which is it because the car only has 19,000 miles. *tr.Mileage was 19000 miles. Mazda Mazda3 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 50 mph.

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems Review #10381253

MAZDA MAZDA3 2010 car safety problem was reported on Dec 09, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS . tl*the contact owns a 2010 mazda, mazda3. while parked, the contact noticed the rear driver side tire was low on air and seemed as if the tire was flat. the vehicle was taken to a tire shop where the technicians stated the sensors were damaged and the tire was not flat. the failure also occurred to the front and rear passenger side tires. the vehicle was taken back to the tire shop where the technicians stated all three tire pressure sensors needed to be replaced. the vehicle was not repaired. the dealer was contacted and stated the repairs would not be covered by warranty because the vehicle was originally taken to the tire shop instead of the dealer. the approximate failure mileage was 32,000. .0 person(s) were injured. 0 person(s) died.Mileage was 32000 miles. Vehicle Identification Number (VIN):JM1BL1H53A1. Mazda Mazda3 2010 problem was reported in MONROE, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Air Bags Frontal

Mazda Mazda3 2010 Air Bags Frontal Review #10384019

MAZDA MAZDA3 2010 car safety problem was reported on May 15, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with AIR BAGS:FRONTAL . tl*the contact owns a 2010 mazda, mazda3. while driving approximately 30 mph with a passenger in the front seat, the contact stated that the air bag light illuminated. the vehicle was taken to an authorized dealer who stated that the vehicle was performing to its specifications. the dealer stated that the failure was related to the passenger's weight as they weighed 105 pounds. the failure continued and the vehicle was taken back to the dealer. a representative of the manufacturer stated that the vehicle was performing properly. the failure was intermittent and had been ongoing since 2010. the vehicle had not been repaired. the failure mileage was 3,000 and the current mileage was 11,400. updated 03/29/11*lj.Mileage was 3000 miles. Vehicle Identification Number (VIN):JM1BL1S62A1. Mazda Mazda3 2010 problem was reported in WHITE PLAINS, NY. Original Owner. Vehicle was purchased on Jan 01, 2010. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 30 mph. DEALER'S NAME: WESTCHESTER PLAZA . DEALER'S TELEPHONE NUMBER: 914-682-5151 . DEALER'S CITY: WHITE PLAINS . DEALER'S STATE CODE: NY. DEALER'S ZIPCODE: 10607 .

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10393775

MAZDA MAZDA3 2010 car safety problem was reported on Mar 10, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . i own a 2010 mazda3. a few weeks ago while driving my front seat made a popping sound and began rocking back and forth causing me to lose control of the car momentarily. i took it into the mazda dealership in alexandria virginia (browns mazda on route 1) and asked them to look at it. they determined that welding on my seat bottom had come undone and needed to be replaced. my car's warranty is for 3 years/36 thousand miles and at the time of the incident my car had 45 thousand miles. mazda declined to fix the seat and stated that i am responsible for the repairs. my contention is that the drivers seat is a safety issue and if involved in a collision the seat may dislodge and cause me more bodily injury than if the seat were properly anchored. i have contacted mazda's customer care line and also e-mailed them and on both occasions they have immediately dismissed my claim stating that my vehicle is out of warranty and the repairs are my responsibility. the drivers seat of a vehicle is an integral part of the safety in the car and due to a manufacturer error my seat is now loose and unsafe to drive. *tr.Mileage was 45000 miles. Vehicle Identification Number (VIN):JM1BL1S55A1. Mazda Mazda3 2010 problem was reported in ALEXANDRIA, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. VEHICLE SPEED: 30 mph.

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems Review #10394222

MAZDA MAZDA3 2010 car safety problem was reported on Apr 04, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS . i own a 2010 mazda speed 3. purchased just over a year ago. i have a valve stem that has broken, which released pressure. the valve stems used on the vehicle are incorporated into tire pressure monitoring system (tmps), and the dealer requires that both items be replaced for $125. aftermarket companies, such as dorman offer replacements that are modular, and allow the consumer to replace just the stem, if broken. the factory, conveniently does not offer them component individually. by the looks of online forums, this is a problem that has been around for a couple of years. i have owned vehicles for 30 years now, and i have never encountered a broken valve stem like this. there is no trauma to the wheel itself that would explain a busted stem that does not protrude beyond the rims outer edge. i believe that this dangerous problem could be eliminated if mazda were to redesign the threaded portion of the stem to be thicker. the aluminum stems are machined so thinly, that they fail, or are easily damaged while performing basic maintenance. the mazda dealer does not feel that the parts are faulty, and they refuse to cover this under warranty. the service manager says they have never heard of this broken stem problem. i find that extremely hard to believe. resolution: i need to get my spare tire off the car, so i will be dropping the wheel off at a tire shop to replace the unit with a standard metal stem until i decide what route to take. my research leads me to believe that this will not be the last problem i have like this, until i get the dangerous factory ones off of my vehicle. *tr.Mileage was 24000 miles. Vehicle Identification Number (VIN):JM1BL1H44A1. Mazda Mazda3 2010 problem was reported in ANAHEIM, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Vehicle Speed Control

Mazda Mazda3 2010 Vehicle Speed Control Review #10399385

MAZDA MAZDA3 2010 car safety problem was reported on June 17, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with VEHICLE SPEED CONTROL . tl*the contact owns a 2010 mazda3. the contact stated that while the vehicle was idle, it would lunge forward and the rpms would increase. the failure occurred intermittently. the contact was forced to push the shut off button to stop the vehicle from moving forward. the vehicle was taken to an authorized dealer who could not duplicate the failure. the vehicle was not repaired. the manufacturer had not been notified. the vin was unavailable. the current mileage was approximately 14,000. the failure mileage was 600..Mileage was 600 miles. Vehicle Identification Number (VIN):JM1BL1S65A1. Mazda Mazda3 2010 problem was reported in BRISTOL, NH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Suspension

Mazda Mazda3 2010 Suspension Review #10404371

MAZDA MAZDA3 2010 car safety problem was reported on Dec 09, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SUSPENSION . tl* the contact owns a 2010 mazda, mazda3. while driving at various speeds, the contact heard a humming noise and the vehicle began to vibrate excessively. the vehicle was taken to two different auto mechanics and they both recommended that the tires not be rotated because of poor tread. prior to the failure, both rear tires were replaced. the technician also informed the contact that the failure was contributed to the suspension which caused the tires to prematurely wear. the manufacturer was made aware of the problem. the failure mileage was 10,000..Mileage was 10000 miles. Vehicle Identification Number (VIN):JM1BL1864A1. Mazda Mazda3 2010 problem was reported in MANASSAS, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems Review #10405715

MAZDA MAZDA3 2010 car safety problem was reported on June 08, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS . tire pressure and regulating systems - i own a 2010 mazda 3 automatic (14,542 miles) --also purchased just over a yr ago. i have now had "three" valve stems that have broken; with slow leaks and flat tires. the last one leaving me stranded for 2 hrs until help arrived. this also happened 2 days after i had my car in for service for another tire with a "valve" stem replacement--costing me $198.00. also told there is no recall and it appears mazda having problems now with this for a few years. also thought it funny that when dealership completing my papers they commented that they just completed exact same papers for car before mine !!!! i am a cautious driver and i know my wheel/tires where not damaged and that was the cause of the valve stem. i now have 3 new valves stems thru my cost ---just waiting for last one to go and then will see how long the "newer" ones last. have a feeling this will be an ongoing problem. at least dealership changed the one today as a good will free of charge. *tr.Mileage was 14542 miles. Mazda Mazda3 2010 problem was reported in APOLLO, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Service Brakes, Hydraulic

Mazda Mazda3 2010 Service Brakes, Hydraulic Review #10406946

MAZDA MAZDA3 2010 car safety problem was reported on June 10, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SERVICE BRAKES, HYDRAULIC . while i was making a exit from the freeway onto a local road, i lost control of the steering wheel while slowly braking. afterwards my car spun out of control and i was in a head on collision with the guard rail for the highway ramp. this happened with my car logging close to 21500 miles. inspection at the body shop determined that issues between the brake pads and steering wheel led to the steering wheel stopping. fixing this problem involves replacing brake and possibly steering components according to the body shop. *tr.Vehicle was involved in a crash. Mileage was 21500 miles. Vehicle Identification Number (VIN):JM1BL1SF7A1. Mazda Mazda3 2010 problem was reported in TROY, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. VEHICLE SPEED: 30 mph.

Mazda Mazda3 2010 Steering

Mazda Mazda3 2010 Steering Review #10406946

MAZDA MAZDA3 2010 car safety problem was reported on June 10, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with STEERING . while i was making a exit from the freeway onto a local road, i lost control of the steering wheel while slowly braking. afterwards my car spun out of control and i was in a head on collision with the guard rail for the highway ramp. this happened with my car logging close to 21500 miles. inspection at the body shop determined that issues between the brake pads and steering wheel led to the steering wheel stopping. fixing this problem involves replacing brake and possibly steering components according to the body shop. *tr.Vehicle was involved in a crash. Mileage was 21500 miles. Vehicle Identification Number (VIN):JM1BL1SF7A1. Mazda Mazda3 2010 problem was reported in TROY, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. VEHICLE SPEED: 30 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10408110

MAZDA MAZDA3 2010 car safety problem was reported on June 13, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . there has not been a failure to date, however, adding my vehicle to the other mazda3's in the data base where the design of the vehicle is creating uneven tire wear. as i have read in no less than 5 blogs, the manufacturer intentionally cambers the rear tires to increase the performance and handling and upon normal rotation of the tires, a "bumping" noise can be heard and felt. the tire manufacturer will do nothing and states is a design issue and mazda states i must deal with the tire manufacturer. this uneven tire wear and vibration could lead to additional tire wear as noted by other owners. at 11,000 miles, i should not be faced with replacing the tires..0 person(s) were injured. 0 person(s) died.Mileage was 11000 miles. Vehicle Identification Number (VIN):JM1BL1H5XA1. Mazda Mazda3 2010 problem was reported in DURHAM, NC. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Suspension Rear

Mazda Mazda3 2010 Suspension Rear Review #10412092

MAZDA MAZDA3 2010 car safety problem was reported on May 23, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SUSPENSION:REAR . excessive rear suspension noise over any surface irregularities, dealer fully aware of right rear sway bar link as source of noise, repaired under warranty. *tr.Mileage was 8283 miles. Vehicle Identification Number (VIN):JM1BL1SF2A1. Mazda Mazda3 2010 problem was reported in WILTON MANORS, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 10 mph.

Mazda Mazda3 2010 Power Train Manual Transmission

Mazda Mazda3 2010 Power Train Manual Transmission Review #10412395

MAZDA MAZDA3 2010 car safety problem was reported on July 10, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN:MANUAL TRANSMISSION . clutch failed at 19.5k miles. ive only had her since november, and with the way i drive theres no way in hell the clutch should go out this soon... now as to explain as to what happened, i was driving on the highway when my engine started reving a bit oddly when i barely pressed on the gas pedal. it went from the normal 2900 rpm in 6th gear at about 65 mph and shot up to 3500 way to quickly then dropped back to 2900 and slowly rose how it shouldve to get me to 70mph...it continued doing this when i got off the highway for about 15 minutes, growing steadily worse until i was unable to get into any gear at all. there was never a smell of clutch inside the car the entire time, no odd noises, no grinding, and the clutch was about half as stiff as it normally was. so i called dealer, they towed my car(course it took forever because they sent the truck to the wrong location haha). it took 2 days before they even got to glance at the car to see what needed to be done(not take apart mind u, just looked), and said the clutch was "smoked" no other specifics but wanted me to authorize them for 525 worth of labor plus parts -_-. so now im stuck fighting them to repair this under warranty(i know theres usually not a warranty unless manufacturers defect..but this is definitely defective). information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6) *tt.Mileage was 19500 miles. Mazda Mazda3 2010 problem was reported in SAXONBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Mazda Mazda3 2010 Equipment Mechanical Jacks

Mazda Mazda3 2010 Equipment Mechanical Jacks Review #10426416

MAZDA MAZDA3 2010 car safety problem was reported on May 20, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with EQUIPMENT:MECHANICAL:JACKS . when jacking the vehicle up to change the tire the main rod that supports the jack bent causing the jack to jump out from under the vehicle and the vehicle fell on the ground. *tr.Mileage was 6000 miles. Vehicle Identification Number (VIN):JM1BL1H54A1. Mazda Mazda3 2010 problem was reported in ROCHESTER HILLS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10430745

MAZDA MAZDA3 2010 car safety problem was reported on Dec 13, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . the front driver's seat support bracket has broken at the weld and it results in the front seat not being stable. it rocks back and forth with acceleration and braking. the entire seat is not stable. *tr.Mileage was 50013 miles. Vehicle Identification Number (VIN):JM1BL1SG1A1. Mazda Mazda3 2010 problem was reported in ROCKLAND, ME. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems Review #10432348

MAZDA MAZDA3 2010 car safety problem was reported on Oct 14, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS . while servicing a 2010 mazda3 we checked the customer's tire pressure as required by law. the valve stem snapped off when an air line was attached to inflate the tire. *tr.Mileage was 37539 miles. Vehicle Identification Number (VIN):JM1BL1SG8A1. Mazda Mazda3 2010 problem was reported in PLEASANTON, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10433019

MAZDA MAZDA3 2010 car safety problem was reported on Oct 24, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . tl* the contact owns a 2010 mazda mazda3. the contact heard a squeaking noise coming from the seat when he would sit. the dealer informed the contact that the weld was fractured on the seat pan. the manufacturer was not notified of the failure. the contact was awaiting repairs to the vehicle. the current and the failure mileage was 19,000. the vin was unavailable. .Mileage was 19000 miles. Mazda Mazda3 2010 problem was reported in RENTON, WA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Wheels Rim

Mazda Mazda3 2010 Wheels Rim Review #10435326

MAZDA MAZDA3 2010 car safety problem was reported on July 10, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS:RIM . the tire pressure warning light came out one week after purchasing my new mazda 3 in july 2010. i filled the tire with air but light would come back on several weeks later. took the car to dealer in october 2010 and they couldn't find any problems. took it back to dealer in october 2011 and now they find a bent wheel rim. replaced the rim at my cost -- over 350.00. 4 weeks later, warning light comes back on. i checked the air on all tires and they are fine. my mazda has only 6,000 miles on it. mazda cannot seem to fix the warning light problem and they blame it on change in weather temperature! complained to the dealer and they say to bring the car back in. i refuse to pay a diagnostic fee when this is clearly a mazda problem and the car is under warranty. i've owned mazda cars since 1993; this is my 6th mazda and i am very upset. *tr.Mileage was 100 miles. Mazda Mazda3 2010 problem was reported in FOREST HILLS, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems Review #10435326

MAZDA MAZDA3 2010 car safety problem was reported on July 10, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS . the tire pressure warning light came out one week after purchasing my new mazda 3 in july 2010. i filled the tire with air but light would come back on several weeks later. took the car to dealer in october 2010 and they couldn't find any problems. took it back to dealer in october 2011 and now they find a bent wheel rim. replaced the rim at my cost -- over 350.00. 4 weeks later, warning light comes back on. i checked the air on all tires and they are fine. my mazda has only 6,000 miles on it. mazda cannot seem to fix the warning light problem and they blame it on change in weather temperature! complained to the dealer and they say to bring the car back in. i refuse to pay a diagnostic fee when this is clearly a mazda problem and the car is under warranty. i've owned mazda cars since 1993; this is my 6th mazda and i am very upset. *tr.Mileage was 100 miles. Mazda Mazda3 2010 problem was reported in FOREST HILLS, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Tires Review #10439264

MAZDA MAZDA3 2010 car safety problem was reported on Dec 09, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . the valve stem of my tire pressure monitoring system (tpms) had significant corrosion leading to immediate and rapid deflation of front left tire while removing air hose while tending to tpms warning light. the rapid deflation was due to complete and immediate severance where the threaded portion of valve stem met valve cap without any torque or abnormal pressure applied. the severed edge of the valve stem shows clear evidence of corrosion 360 degrees and inward, with a thin halo (appx. 1/10 of the wall) remaining. both the tire and valve stem showed no sign of leaking and held proper pressure while filling to recommended pressure until removal of air hose caused the stem to split horizontally between the 9th and 10th thread. plastic valve caps were in place on all 4 tires. spare tire also not able to be put in place due to 'stuck' lug nuts on same tire; similar corrosion is suspect, possibly caused by galvanic corrosion due to metals found in disk brakes, shoes or alloy rim. vehicle is still under warranty and needed tow to nearest mazda dealership for repair. when calling the service department about sending my vehicle over i addressed my concerns about the other 3 valve stems needing replacement and was told "they are $150 each so if you want to pay to have the other ones replaced you can, but the dealership isn't going to pay for it" my response: "really? i'm thankful this didn't happen on the highway, i would hope the safety of your customers would come first" ..no im sorry, no we'll look into it for you, just "well can i give you the number for roadside assistance?" *tr.Mileage was 25000 miles. Mazda Mazda3 2010 problem was reported in GLOUCESTER, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10439264

MAZDA MAZDA3 2010 car safety problem was reported on Dec 09, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . the valve stem of my tire pressure monitoring system (tpms) had significant corrosion leading to immediate and rapid deflation of front left tire while removing air hose while tending to tpms warning light. the rapid deflation was due to complete and immediate severance where the threaded portion of valve stem met valve cap without any torque or abnormal pressure applied. the severed edge of the valve stem shows clear evidence of corrosion 360 degrees and inward, with a thin halo (appx. 1/10 of the wall) remaining. both the tire and valve stem showed no sign of leaking and held proper pressure while filling to recommended pressure until removal of air hose caused the stem to split horizontally between the 9th and 10th thread. plastic valve caps were in place on all 4 tires. spare tire also not able to be put in place due to 'stuck' lug nuts on same tire; similar corrosion is suspect, possibly caused by galvanic corrosion due to metals found in disk brakes, shoes or alloy rim. vehicle is still under warranty and needed tow to nearest mazda dealership for repair. when calling the service department about sending my vehicle over i addressed my concerns about the other 3 valve stems needing replacement and was told "they are $150 each so if you want to pay to have the other ones replaced you can, but the dealership isn't going to pay for it" my response: "really? i'm thankful this didn't happen on the highway, i would hope the safety of your customers would come first" ..no im sorry, no we'll look into it for you, just "well can i give you the number for roadside assistance?" *tr.Mileage was 25000 miles. Mazda Mazda3 2010 problem was reported in GLOUCESTER, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10440543

MAZDA MAZDA3 2010 car safety problem was reported on July 01, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . power driver seat rocks forward and backward during acceleration and sudden braking. approx. 1/2" play. the movement is very noticeable and disconcerting. i fear that i may lose control of the vehicle. dealer insists condition is normal. *tr.Mileage was 17500 miles. Vehicle Identification Number (VIN):JM1BL1H50A1. Mazda Mazda3 2010 problem was reported in SANDY SPRINGS, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Power Train

Mazda Mazda3 2010 Power Train Review #10440881

MAZDA MAZDA3 2010 car safety problem was reported on Dec 13, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . i purchased a 2010 mazda 3 as a demo on july 30, 2011 with 4100 miles on it. i now have 8500 miles on it and the clutch has failed. after taking it to the local mazda dealership, i was told it was a normal wear produce and it had been abused so i had to pay for the repair. when i bought the car it had a high release in the clutch pedal but i figured it was normal for the car. since early november, the "intake manifold runner" has been extremely sensitive to the point that i cannot maintain speed up a slight incline without the engine revving up. i was told when i took the car to the dealership this was due to a clutch failure. i don't believe it is acceptable for a clutch to go out after just 8500 miles of driving. my previous vehicle went over 100,000 miles of my same driving and manual transmission without any clutch issues. i am not happy with mazda, mazda parts, and mazda's customer assistance on this issue. *tr.Mileage was 8500 miles. Vehicle Identification Number (VIN):jm1bl1s53a1. Mazda Mazda3 2010 problem was reported in KNOXVILLE, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Power Train Review #10441490

MAZDA MAZDA3 2010 car safety problem was reported on Dec 24, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . at less than 24,000 miles, my clutch has begun to slip terribly and creates a terrible burning smell. i know there are hundreds of other mazda owners who have also had to replace their clutches before they've had to replace brake pads. this is a drain on consumers, and a safety issue to boot. *tr.Mileage was 24000 miles. Mazda Mazda3 2010 problem was reported in SOUTH RIVER, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Engine And Engine Cooling

Mazda Mazda3 2010 Engine And Engine Cooling Review #10441490

MAZDA MAZDA3 2010 car safety problem was reported on Dec 24, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ENGINE AND ENGINE COOLING . at less than 24,000 miles, my clutch has begun to slip terribly and creates a terrible burning smell. i know there are hundreds of other mazda owners who have also had to replace their clutches before they've had to replace brake pads. this is a drain on consumers, and a safety issue to boot. *tr.Mileage was 24000 miles. Mazda Mazda3 2010 problem was reported in SOUTH RIVER, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Service Brakes, Hydraulic

Mazda Mazda3 2010 Service Brakes, Hydraulic Review #10441490

MAZDA MAZDA3 2010 car safety problem was reported on Dec 24, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SERVICE BRAKES, HYDRAULIC . at less than 24,000 miles, my clutch has begun to slip terribly and creates a terrible burning smell. i know there are hundreds of other mazda owners who have also had to replace their clutches before they've had to replace brake pads. this is a drain on consumers, and a safety issue to boot. *tr.Mileage was 24000 miles. Mazda Mazda3 2010 problem was reported in SOUTH RIVER, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Electrical System

Mazda Mazda3 2010 Electrical System Review #10443658

MAZDA MAZDA3 2010 car safety problem was reported on Jan 13, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ELECTRICAL SYSTEM . mazda has issues with condensation in front lights and real lights leading to excessive water building up in light cavity. the water restricts light and has shorted out headlight bulb on several occasions as i drove down the road. this causes a serious issue at night as i am driving. mazda and dealer refuse to fix sighting bulletin from mazda that this is a known problem and not to fix unless light enclosure is full of water. *tr.Mileage was 17500 miles. Vehicle Identification Number (VIN):JM1BL1SF7A1. Mazda Mazda3 2010 problem was reported in CEDAR PARK, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 5 mph.

Mazda Mazda3 2010 Exterior Lighting

Mazda Mazda3 2010 Exterior Lighting Review #10443658

MAZDA MAZDA3 2010 car safety problem was reported on Jan 13, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with EXTERIOR LIGHTING . mazda has issues with condensation in front lights and real lights leading to excessive water building up in light cavity. the water restricts light and has shorted out headlight bulb on several occasions as i drove down the road. this causes a serious issue at night as i am driving. mazda and dealer refuse to fix sighting bulletin from mazda that this is a known problem and not to fix unless light enclosure is full of water. *tr.Mileage was 17500 miles. Vehicle Identification Number (VIN):JM1BL1SF7A1. Mazda Mazda3 2010 problem was reported in CEDAR PARK, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 5 mph.

Mazda Mazda3 2010 Suspension

Mazda Mazda3 2010 Suspension Review #10445739

MAZDA MAZDA3 2010 car safety problem was reported on May 17, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SUSPENSION . my new 2010 mazda 3 hatchback was showing signs of unusual high/irregular tire wear. the tires were rotated as per the company recommended schedule. it was found that the rear trailing arms and lower shock bolts were loose. at 22,000 miles the front tires that had been rotated to the rear were also wearing uneven and at a high rate considering this was only more than a 5,000 mile period. the vehicle was taken to mazda on janurary 17,2012 informing them that i had checked online and this excessive tire wear has been known by mazda for over (5) years. the service manager confirmed this issue and mazda has done nothing to repair/recall the vehicle. the service manager also stated that almost all of the mazda 3 model have the same problem. looking through other mazda owners who have had tires wear out at or around the 25,000 mile range that there is a fix for the problem. i.e. an adjustable camber rod which one owner had done and the car went .....60,000 miles on a set of tires. mazda knows of this problem, has not done anything except produce more vehicles with this problem and there is a damned fix for it..it also is amazing and damning that this adjustable rod is manufactured by...........m a z d a....i would demand an announcement and recall of these vehicles as the inside of the tire wears at an extremely high rate and for those that do not check the tire condition of their car nor to rotate the tires, this will lead to a tire failure/blowout which will create a high accident risk. mazda knows the problem and has done nothing, make it public,demand a recall and ensure compliance to this potential serious problem is resolved. case#415686 information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6) *tt.Mileage was 15449 miles. Vehicle Identification Number (VIN):JM1BL1H63A1. Mazda Mazda3 2010 problem was reported in MECHANICSBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL TYPE: GAS.

Mazda Mazda3 2010 Power Train

Mazda Mazda3 2010 Power Train Review #10447652

MAZDA MAZDA3 2010 car safety problem was reported on Feb 01, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . i have had my 2010 mazda 3s since june of 2010 when i bought it new. i drive to and from work every day. i have 26,000 miles on it, 75% of which are highway miles. i was driving to work last week, and noticed something with the car felt off. every day of the week it got worse and worse, so i finally brought it to my mechanic who told me, as i suspected, that the clutch was slipping and nearing the end of its life. i have yet to replace the brake pads on this car, and to get told that the clutch is gone before i even replace normal maintenance items is just flat out unacceptable. i have had two previous cars with manual transmissions, and never replaced a clutch, even when they had close to 100,000 miles on them. my mechanic suggested before i do anything, to look on forums and see if anyone else has been having similar problems with premature clutch wear. i have spent my whole weekend on mazda and edmunds forums reading about countless people with my model year, 2010, who have had clutches go before 35,000 miles. this is not a one-off case, and it is certainly not a "wear and tear" issue as the dealership says it is. that's their blanket cover-their-[xxx]statement because they know they put out a poor product and don't want to deal with the costs incurred with replacing them. i have no faith anymore in my local dealership, or mazda as a brand at this point. with the significant number of similar issues to mine, the fact that they are still unwilling to admit that they chose an inferior supplier to cut costs for one of the most crucial parts of the car, that isn't covered under warranty, is just piss poor business practice. i don't know what writing this will do, if anything, but i decided that i am done being [xxx] around by the dealer and hopefully this is followed by other mazda owners who share the distaste for their product and service as i do. information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).*tr.Mileage was 26000 miles. Mazda Mazda3 2010 problem was reported in GARDEN CITY, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 25 mph.

Mazda Mazda3 2010 Engine And Engine Cooling

Mazda Mazda3 2010 Engine And Engine Cooling Review #10447652

MAZDA MAZDA3 2010 car safety problem was reported on Feb 01, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ENGINE AND ENGINE COOLING . i have had my 2010 mazda 3s since june of 2010 when i bought it new. i drive to and from work every day. i have 26,000 miles on it, 75% of which are highway miles. i was driving to work last week, and noticed something with the car felt off. every day of the week it got worse and worse, so i finally brought it to my mechanic who told me, as i suspected, that the clutch was slipping and nearing the end of its life. i have yet to replace the brake pads on this car, and to get told that the clutch is gone before i even replace normal maintenance items is just flat out unacceptable. i have had two previous cars with manual transmissions, and never replaced a clutch, even when they had close to 100,000 miles on them. my mechanic suggested before i do anything, to look on forums and see if anyone else has been having similar problems with premature clutch wear. i have spent my whole weekend on mazda and edmunds forums reading about countless people with my model year, 2010, who have had clutches go before 35,000 miles. this is not a one-off case, and it is certainly not a "wear and tear" issue as the dealership says it is. that's their blanket cover-their-[xxx]statement because they know they put out a poor product and don't want to deal with the costs incurred with replacing them. i have no faith anymore in my local dealership, or mazda as a brand at this point. with the significant number of similar issues to mine, the fact that they are still unwilling to admit that they chose an inferior supplier to cut costs for one of the most crucial parts of the car, that isn't covered under warranty, is just piss poor business practice. i don't know what writing this will do, if anything, but i decided that i am done being [xxx] around by the dealer and hopefully this is followed by other mazda owners who share the distaste for their product and service as i do. information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).*tr.Mileage was 26000 miles. Mazda Mazda3 2010 problem was reported in GARDEN CITY, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 25 mph.

Mazda Mazda3 2010 Vehicle Speed Control

Mazda Mazda3 2010 Vehicle Speed Control Review #10449593

MAZDA MAZDA3 2010 car safety problem was reported on Feb 20, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with VEHICLE SPEED CONTROL . on 2 occasions i was completely stopped, for a red light and stop sign, when the engine revved on its own and the car lurched forward. felt like i was pushing brake pedal through the floor to stop it but it recovered on its own after several seconds. very scary. i am afraid of hitting a car or someone. at the mazda dealer now and has been for a week as they try to find out the problem. *tr.Mileage was 24000 miles. Mazda Mazda3 2010 problem was reported in SPENCERPORT, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Engine And Engine Cooling

Mazda Mazda3 2010 Engine And Engine Cooling Review #10450415

MAZDA MAZDA3 2010 car safety problem was reported on July 10, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ENGINE AND ENGINE COOLING . heat is always hot. there is no temperature contol on the heater. *tr.Vehicle Identification Number (VIN):JM1BL1H54A1. Mazda Mazda3 2010 problem was reported in EATONTON, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda3 2010 Visibility Defroster/defogger System

Mazda Mazda3 2010 Visibility Defroster/defogger System Review #10450415

MAZDA MAZDA3 2010 car safety problem was reported on July 10, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with VISIBILITY:DEFROSTER/DEFOGGER SYSTEM . heat is always hot. there is no temperature contol on the heater. *tr.Vehicle Identification Number (VIN):JM1BL1H54A1. Mazda Mazda3 2010 problem was reported in EATONTON, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda3 2010 Engine And Engine Cooling Cooling System Radiator Assembly

Mazda Mazda3 2010 Engine And Engine Cooling Cooling System Radiator Assembly Review #10451085

MAZDA MAZDA3 2010 car safety problem was reported on Jan 06, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY . i am the original owner of this vehicle, purchased brand new. in january 2012 the heater when turning on made a loud clicking sound for approx. 20 to 30 seconds, each time. upon research on the internet, local mechanics, i found out the heater blend door actuator is the problem. i was going to replace it, but upon further investigation i found that this heater assembly is not only used by mazda, nissan, toyota, chevy, ford, and lexus. this heater is known to have this design error. i then decided to have the mazda dealer change it for $130.00. the dealer then told me the whole assembly needed changing for $250.00 plus labor. this assembly was known for this. also the dealer had unplugged the heater blend door actuator because this unit is known to start a fire in the vehicle. this made me extremely nervous. i consider this to be an unsafe vehicle. *tr *js.Mileage was 57890 miles. Vehicle Identification Number (VIN):JM1BL1SG8A1. Mazda Mazda3 2010 problem was reported in NEW MILFORD, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Visibility

Mazda Mazda3 2010 Visibility Review #10452015

MAZDA MAZDA3 2010 car safety problem was reported on Jan 12, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with VISIBILITY . i am the original owner of this vehicle, purchased brand new. in january 2010. the heater when turning on, made a loud clicking sound for approx. 20- 30 seconds, each time. upon research on the internet, local mechanics, i found out the heater blend door actuator is the problem. i was going to replace it, but upon further investigation i found that this heater assembly is not only used by mazda, nissan, toyota, chevy, ford, and lexus. this is heater is known to have this design error. also the dealer had unplugged the heater blend door actuator because this unit is known to start a fire in the vehicle. this made me extremely nervous. i consider this to be an unsafe vehicle. .0 person(s) were injured. 0 person(s) died.Mileage was 62764 miles. Vehicle Identification Number (VIN):JM1BL1SG8A1. Mazda Mazda3 2010 problem was reported in NEW MILFORD, PA. Original Owner. Vehicle was purchased on Jan 01, 2010. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Electrical System

Mazda Mazda3 2010 Electrical System Review #10452015

MAZDA MAZDA3 2010 car safety problem was reported on Jan 12, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ELECTRICAL SYSTEM . i am the original owner of this vehicle, purchased brand new. in january 2010. the heater when turning on, made a loud clicking sound for approx. 20- 30 seconds, each time. upon research on the internet, local mechanics, i found out the heater blend door actuator is the problem. i was going to replace it, but upon further investigation i found that this heater assembly is not only used by mazda, nissan, toyota, chevy, ford, and lexus. this is heater is known to have this design error. also the dealer had unplugged the heater blend door actuator because this unit is known to start a fire in the vehicle. this made me extremely nervous. i consider this to be an unsafe vehicle. .0 person(s) were injured. 0 person(s) died.Mileage was 62764 miles. Vehicle Identification Number (VIN):JM1BL1SG8A1. Mazda Mazda3 2010 problem was reported in NEW MILFORD, PA. Original Owner. Vehicle was purchased on Jan 01, 2010. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Tires Valve

Mazda Mazda3 2010 Tires Valve Review #10452288

MAZDA MAZDA3 2010 car safety problem was reported on Mar 16, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES:VALVE . while checking and inflating a customer's tires the valve stem broke causing the tire to completely deflate. *js.Mileage was 48844 miles. Mazda Mazda3 2010 problem was reported in PLEASANTON, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10454300

MAZDA MAZDA3 2010 car safety problem was reported on Apr 05, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . drivers side seat broke at welded attachment point to adjuster rail.Mileage was 55790 miles. Vehicle Identification Number (VIN):JM1BL1H56A1. Mazda Mazda3 2010 problem was reported in DECATUR, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph.

Mazda Mazda3 2010 Structure Body

Mazda Mazda3 2010 Structure Body Review #10454574

MAZDA MAZDA3 2010 car safety problem was reported on Feb 08, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with STRUCTURE:BODY . the driver side interior door latch cable broke. this is the second time this has happened with the new mazda 3. *tr.Mileage was 45000 miles. Mazda Mazda3 2010 problem was reported in LYNDHURST, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Vehicle Speed Control

Mazda Mazda3 2010 Vehicle Speed Control Review #10456667

MAZDA MAZDA3 2010 car safety problem was reported on Nov 11, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with VEHICLE SPEED CONTROL . many times but sporadically over the last two years my mazda 3, when coming to a stop and foot firmly on the brake will have a sudden surge in rpm between 1200-2500 rpm and try to accelerate. seems to happen most often first thing in the morning more often. because i am constantly ready there has been no crash, though the time rpms reached 2500 i had difficulty stopping the car, on a freeway on ramp where sudden deceleration was needed. i have found that one pump of the break alleviates the problem if there is room to do so. *tr.Mileage was 5000 miles. Vehicle Identification Number (VIN):JM1BL1SG0A1. Mazda Mazda3 2010 problem was reported in RENTON, WA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 10 mph.

Mazda Mazda3 2010 Power Train

Mazda Mazda3 2010 Power Train Review #10456667

MAZDA MAZDA3 2010 car safety problem was reported on Nov 11, 2010.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . many times but sporadically over the last two years my mazda 3, when coming to a stop and foot firmly on the brake will have a sudden surge in rpm between 1200-2500 rpm and try to accelerate. seems to happen most often first thing in the morning more often. because i am constantly ready there has been no crash, though the time rpms reached 2500 i had difficulty stopping the car, on a freeway on ramp where sudden deceleration was needed. i have found that one pump of the break alleviates the problem if there is room to do so. *tr.Mileage was 5000 miles. Vehicle Identification Number (VIN):JM1BL1SG0A1. Mazda Mazda3 2010 problem was reported in RENTON, WA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 10 mph.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10459135

MAZDA MAZDA3 2010 car safety problem was reported on Apr 02, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . i was driving along and felt the drivers seat shift backwards. from that point on the seat was unsteady and moved forward and backward depending on which i was doing, accelerating or breaking. upon examination, it was found that the weld on the seat bracket had broken. in my opinion, this is a very unusual break and could be very hazardous if it happens upon braking. *tt.0 person(s) were injured. 0 person(s) died.Mileage was 55000 miles. Vehicle Identification Number (VIN):JM1BL1SF9A1. Mazda Mazda3 2010 problem was reported in HOUSTON, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 45 mph.

Mazda Mazda3 2010 Seats Review #10459475

MAZDA MAZDA3 2010 car safety problem was reported on May 18, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . from the start my drivers seat was loose. i have taken it to the dealer and each time the problem was not solved, the replaced the track assembly, tightened things up and after a few hundred miles the problem returned. *tt on the day of my accident, i was stopped at light and was the car behind me. a different car smashed through the car behind me causing that vehicle to hit me from behind and forcing me into the car in front of me. no air bags deployed and no one was hurt. after the incident, i got back into my car and the seat rocked as if it was a rocking chair. driving the car home, the seat rocked to every bump in the road. i have reason to believe if i was impacted with higher force the seat would have came loose from the base..Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Mileage was 30000 miles. Vehicle Identification Number (VIN):JM1BL1H50A1. Mazda Mazda3 2010 problem was reported in ROYAL OAK, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Steering

Mazda Mazda3 2010 Steering Review #10461029

MAZDA MAZDA3 2010 car safety problem was reported on June 07, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with STEERING . tl* the contact owns a 2010 mazda mazda3. the contact stated that while driving 35 mph, he turned left and the steerng wheel seized. the warning light also illuminated on the instrument panel. the steering wheel returned to normal function a few minutes later. the vehicle was not taken to the dealer. the dealer was notified and the contact was informed that there were no recalls addressing the failure. the manufacture was contacted and they also stated that there were not any recalls. the failure and current mileages were 40,700. .0 person(s) were injured. 0 person(s) died.Mileage was 40700 miles. Vehicle Identification Number (VIN):JM1BL1SG8A1. Mazda Mazda3 2010 problem was reported in LAQUINTA, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Mazda Mazda3 2010 Seat Belts

Mazda Mazda3 2010 Seat Belts Review #10462879

MAZDA MAZDA3 2010 car safety problem was reported on May 30, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEAT BELTS . the sensor for passenger air bag off starting staying on, nothing was in the passenger seat. now the sensor thinks someone is in the seat ( when no one is in seat) and keeps flashing the buckle seat belt warning. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 44000 miles. Mazda Mazda3 2010 problem was reported in WINSTON SALEM, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Air Bags

Mazda Mazda3 2010 Air Bags Review #10462879

MAZDA MAZDA3 2010 car safety problem was reported on May 30, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with AIR BAGS . the sensor for passenger air bag off starting staying on, nothing was in the passenger seat. now the sensor thinks someone is in the seat ( when no one is in seat) and keeps flashing the buckle seat belt warning. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 44000 miles. Mazda Mazda3 2010 problem was reported in WINSTON SALEM, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Visibility Sun Roof Assembly

Mazda Mazda3 2010 Visibility Sun Roof Assembly Review #10466594

MAZDA MAZDA3 2010 car safety problem was reported on July 19, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with VISIBILITY:SUN ROOF ASSEMBLY . hi, this morning i was driving on my way to work when all of a sudden my entire sunroof exploded and shattered. there was nothing that hit my car, nor nothing that hit my sunroof. i was traveling at 65mph on i-25 in albuquerque, nm. neither the sunroof nor the car have been changed in anyway from their stock form. the explosion of the sunroof was very scary and almost cause me to crash. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 19000 miles. Vehicle Identification Number (VIN):JM1BL1H50A1. Mazda Mazda3 2010 problem was reported in ALBUQUERQUE, NM. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Mazda Mazda3 2010 Structure Body

Mazda Mazda3 2010 Structure Body Review #10466594

MAZDA MAZDA3 2010 car safety problem was reported on July 19, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with STRUCTURE:BODY . hi, this morning i was driving on my way to work when all of a sudden my entire sunroof exploded and shattered. there was nothing that hit my car, nor nothing that hit my sunroof. i was traveling at 65mph on i-25 in albuquerque, nm. neither the sunroof nor the car have been changed in anyway from their stock form. the explosion of the sunroof was very scary and almost cause me to crash. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 19000 miles. Vehicle Identification Number (VIN):JM1BL1H50A1. Mazda Mazda3 2010 problem was reported in ALBUQUERQUE, NM. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Mazda Mazda3 2010 Tires Valve

Mazda Mazda3 2010 Tires Valve Review #10471870

MAZDA MAZDA3 2010 car safety problem was reported on Aug 21, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES:VALVE . tl* the contact owns a 2010 mazda mazda3. the contact stated that the front passenger side tire valve stem failed. the contact mentioned that the valve stem cracked in half. the vehicle was not taken to the dealer. the manufacturer was made aware of the failure. the vehicle was not repaired. the vin was not available. the failure and current mileage was 24,750. .0 person(s) were injured. 0 person(s) died.Mileage was 24750 miles. Mazda Mazda3 2010 problem was reported in COMMACK, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Steering

Mazda Mazda3 2010 Steering Review #10472056

MAZDA MAZDA3 2010 car safety problem was reported on July 01, 2011.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with STEERING . have had intermittent power steering loss with indicator light illumination for approximately one year. after engine gets up to temp power steering cuts out. it will sometimes resume after stopping to let the engine cool. current recall extends to 2007-2009 model year vehicles until the month before my vehicle was made. mazda refuses to recognize that this could be related and since vehicle is out of warranty won't repair. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 38000 miles. Vehicle Identification Number (VIN):JM1BL1SGXA1. Mazda Mazda3 2010 problem was reported in FOREST GROVE, OR. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 50 mph.

Mazda Mazda3 2010 Steering Review #10474294

MAZDA MAZDA3 2010 car safety problem was reported on Aug 29, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with STEERING . on august 29th while driving with my 2010 mazda 3, going about 30 miles an hour, the power steering wheel locked up, and all the warning/indicator lights came on. i completely lost control of the car. i tried to re-start the car, but the car would not start and the warning/indicator lights came on steady, with the exception of the electronic steering lock warning light, which was flashing red. it was not a battery issue because the radio and lights worked fine. i had the car towed to a mazda dealer. the mazda dealership said that they did not know what the issue was because they could not access the pcm to read the error code to understand what happened, and they ended up replacing the pcm. i called mazda customer assistance and complained and they told me that the pcm failure does not relate to the steering wheel locking up. this is similar to complain #10461029. i do not feel safe driving this car again, and i would like mazda to take it back. it only has 23000 miles, and i have another 6 month to go on my lease. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 23000 miles. Vehicle Identification Number (VIN):JM1BL1SG3A1. Mazda Mazda3 2010 problem was reported in BOONTON, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 30 mph.

Mazda Mazda3 2010 Electrical System

Mazda Mazda3 2010 Electrical System Review #10474294

MAZDA MAZDA3 2010 car safety problem was reported on Aug 29, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ELECTRICAL SYSTEM . on august 29th while driving with my 2010 mazda 3, going about 30 miles an hour, the power steering wheel locked up, and all the warning/indicator lights came on. i completely lost control of the car. i tried to re-start the car, but the car would not start and the warning/indicator lights came on steady, with the exception of the electronic steering lock warning light, which was flashing red. it was not a battery issue because the radio and lights worked fine. i had the car towed to a mazda dealer. the mazda dealership said that they did not know what the issue was because they could not access the pcm to read the error code to understand what happened, and they ended up replacing the pcm. i called mazda customer assistance and complained and they told me that the pcm failure does not relate to the steering wheel locking up. this is similar to complain #10461029. i do not feel safe driving this car again, and i would like mazda to take it back. it only has 23000 miles, and i have another 6 month to go on my lease. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 23000 miles. Vehicle Identification Number (VIN):JM1BL1SG3A1. Mazda Mazda3 2010 problem was reported in BOONTON, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 30 mph.

Mazda Mazda3 2010 Power Train

Mazda Mazda3 2010 Power Train Review #10477007

MAZDA MAZDA3 2010 car safety problem was reported on Sept 20, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . the clutch on my manual transmission 2010 mazda3 suddenly stopped operating properly. it grinds gears and does not change gears when i shift. i drove the vehicle in to a mazda dealer on saturday, with a week left on my warranty. on monday, they called to tell me that their technician could not even drive my car as there was no clutch pad! i wondered how i could drive the car to them, but once it was in their possession, it was suddenly undriveable. i am now being forced to pay $1100 to replace the clutch, because they say my warranty does not cover normal wear and tear. i asked how a completely disintegrated clutch pad is "normal wear and tear" on a vehicle which has only been driven 16k miles! this could have been dangerous had it failed completely while driving! i filed a claim with the better business bureau. i also called the mazda corporate office for assistance, where i was told i could simply voice a complaint. "tom" refused to allow me to speak with a supervisor or anyone higher than himself (he was just a call-center employee). he offered to call the dealership and ask them to provide me with a discount. when i spoke to the dealer today, they said tom did call them, but never asked for any discounts! all he did was explain that mazda has not recalled the clutch, so my warranty would not cover the necessary replacement. mazda sold me a sub-par vehicle, and now they lied about their way of handling the error. i looked online and have found several complaints on the same vehicle claiming the exact same problems on a low-mileage clutch. this clearly is a manufacturing defect, not driver error. it should be recalled as the problem is so common in this exact make and model with such low miles. $1100 later and i get a new shoddy clutch which i will have to replace in another 16k miles. disappointed and will never own another mazda again if this is not resolved. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 16680 miles. Mazda Mazda3 2010 problem was reported in HORSHAM, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Steering

Mazda Mazda3 2010 Steering Review #10477284

MAZDA MAZDA3 2010 car safety problem was reported on Sept 22, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with STEERING . tl* the contact owns a 2010 mazda mazda3. the contact stated that the power steering assist malfunctioned. the vehicle was taken to the dealer where it was confirmed that the power steering assist had failed. the vehicle was not repaired. the manufacturer was contacted about the issue adn provided no assistance. the vehicle was not repaired. the failure and current mileages were 26,000. .0 person(s) were injured. 0 person(s) died.Mileage was 26000 miles. Vehicle Identification Number (VIN):JM1BL1S56A1. Mazda Mazda3 2010 problem was reported in WINCHESTER, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Exterior Lighting

Mazda Mazda3 2010 Exterior Lighting Review #10482622

MAZDA MAZDA3 2010 car safety problem was reported on Oct 16, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with EXTERIOR LIGHTING . the headlights on my 2010 mazda 3s shine 25' distant 7' off the ground mazda says its designed that way. this is a safety issue. mazda says the lights are adjusted as high as possible and nothing can be done. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 8500 miles. Vehicle Identification Number (VIN):JM1BL1S66A1. Mazda Mazda3 2010 problem was reported in HARRISBURG, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda3 2010 Power Train

Mazda Mazda3 2010 Power Train Review #10483641

MAZDA MAZDA3 2010 car safety problem was reported on Oct 26, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . clutches are supposed to be bullet proof. being one of the main parts of the car and necessary to it's basic function, clutches should be included in the 5 year/60,000 miles warranty. but they're not. the clutch on the 2010 mazda3 is only covered for 7500 miles. that's suspicious in and of itself. so here's my story, my clutch gave out after 50,000 miles. no warning or anything. the mechanic i took it to said in the 32 years he's been fixing clutches, he's never seen anything so horrific. he had to have metal fabricators come in and make parts because some of the surrounding equipment was so warped. mazda claims no responsibility for their faulty product. i've read stories online where people report their clutch blowing out at 14,000 miles. edmunds.com, a leader in car resources rates the clutch problem on this specific car at a 9.7/10. it's a faulty part in a car and mazda will not even consider it to be an actual thing. it's not right at all. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 50000 miles. Mazda Mazda3 2010 problem was reported in WINDHAM, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Mazda Mazda3 2010 Power Train Review #10483962

MAZDA MAZDA3 2010 car safety problem was reported on Oct 23, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . i brought my car into an authorized mazda dealer for an oil change and mentioned that i noticed a slight slipping in the clutch. i was later informed by the dealer that even though i had just 33,000 highway miles, the entire clutch assembly needed to be replaced. even though i was still within the warranty period, they told me that it would not be covered. i complained to mazda customer care and got no where. the most frustrating part is that after the dealer completed the repair, they told me that the clutch showed no signs of abuse and that in their professional opinion, this was a premature failure of the clutch. even with this information, mazda itself still would not cover the repair. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 33452 miles. Vehicle Identification Number (VIN):JM1BL1H61A1. Mazda Mazda3 2010 problem was reported in BREWSTER, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10484707

MAZDA MAZDA3 2010 car safety problem was reported on Nov 08, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . tl* the contact owns a 2010 mazda mazda3. the contact stated that the driver's side plastic height adjuster for the seat broke, causing the seat to move whenever the contact completed a turn. the vehicle was taken to the dealer who diagnosed that the height adjuster needed to be replaced. the manufacturer was made aware of the failure who did not offer any assistance since the vehicle was no longer under warranty. the vehicle was not repaired. the failure and current mileage was 47,000. .0 person(s) were injured. 0 person(s) died.Mileage was 47000 miles. Vehicle Identification Number (VIN):JM1BL1S57A1. Mazda Mazda3 2010 problem was reported in HALTOM CITY, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Power Train

Mazda Mazda3 2010 Power Train Review #10485133

MAZDA MAZDA3 2010 car safety problem was reported on Oct 01, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . at around 24,000 miles i experienced a partial clutch failure (couldn't shift out of gear) that went away after pumping the clutch petal. i asked the dealership about this and was told not to worry about it, and that it was probably due to clutch freezing up in the cold. at around 30,000 miles the car started shaking whenever i engaged/disengaged the clutch. in order to get the clutch to engage at all i had to let off the clutch petal much slower than usual. i took the car to the original dealership it was purchased at and was told the friction disc was worn out, and that this was a wear and tear item and therefore not under warranty. in addition, they said that the pilot bearing had failed. after getting these items replaced a loud creaking noise occurs whenever engaging/disengaging the clutch or accelerator pedals. the issue is still not resolved. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 30000 miles. Mazda Mazda3 2010 problem was reported in BLACKSBURG, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10487652

MAZDA MAZDA3 2010 car safety problem was reported on Dec 06, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . new car, mazda m3, purchased in april 2010. yokohama tires were on the car. car currently has approximately 18,000 miles and tires have been rotated. last night while traveling approximately 40mph, the rear passenger tire went flat. upon removing the tire to fix the flat, the sidewall had split from the tread. this happened on the inside of the tire meaning the side of the tire against the car so it was not visible from just looking at the outside of the tire. the split is 15 inches in length and i can see that there are other areas that look like they are about to split as well. i found nhtsa campaign id number: 12t025000 talking about recall of a yokohama tire that seems to match what i have had. i have contacted my car dealer as the recall says the dealer will replace free of charge, but they aren't aware of any recall. i've been on hold for yokohama for 30+ minutes with no luck in speaking to a live person. i can't afford not to have a car and based on all i've read about these tires, i can't afford to have my children ride on tires that perform like this. i can't afford to wait on a process to determine if yokohama will make good on their warranty claims. i have to purchase new tires and will be purchasing 4 new tires and not yokohama. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 18000 miles. Vehicle Identification Number (VIN):JM1BL1K55B1. Mazda Mazda3 2010 problem was reported in THE WOODLANDS, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Mazda Mazda3 2010 Tires Sidewall

Mazda Mazda3 2010 Tires Sidewall Review #10487652

MAZDA MAZDA3 2010 car safety problem was reported on Dec 06, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES:SIDEWALL . new car, mazda m3, purchased in april 2010. yokohama tires were on the car. car currently has approximately 18,000 miles and tires have been rotated. last night while traveling approximately 40mph, the rear passenger tire went flat. upon removing the tire to fix the flat, the sidewall had split from the tread. this happened on the inside of the tire meaning the side of the tire against the car so it was not visible from just looking at the outside of the tire. the split is 15 inches in length and i can see that there are other areas that look like they are about to split as well. i found nhtsa campaign id number: 12t025000 talking about recall of a yokohama tire that seems to match what i have had. i have contacted my car dealer as the recall says the dealer will replace free of charge, but they aren't aware of any recall. i've been on hold for yokohama for 30+ minutes with no luck in speaking to a live person. i can't afford not to have a car and based on all i've read about these tires, i can't afford to have my children ride on tires that perform like this. i can't afford to wait on a process to determine if yokohama will make good on their warranty claims. i have to purchase new tires and will be purchasing 4 new tires and not yokohama. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 18000 miles. Vehicle Identification Number (VIN):JM1BL1K55B1. Mazda Mazda3 2010 problem was reported in THE WOODLANDS, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Mazda Mazda3 2010 Tires Valve

Mazda Mazda3 2010 Tires Valve Review #10490523

MAZDA MAZDA3 2010 car safety problem was reported on Dec 23, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES:VALVE . spontaneous failure of tire valve stem resulting in the near instantaneous decompression of the rear driver's side tire. at the time i was attempting to check the tire pressure of that wheel. the stem separated into two pieces without any prior indication of wear. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 11000 miles. Mazda Mazda3 2010 problem was reported in PITTSBURGH, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10490523

MAZDA MAZDA3 2010 car safety problem was reported on Dec 23, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . spontaneous failure of tire valve stem resulting in the near instantaneous decompression of the rear driver's side tire. at the time i was attempting to check the tire pressure of that wheel. the stem separated into two pieces without any prior indication of wear. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 11000 miles. Mazda Mazda3 2010 problem was reported in PITTSBURGH, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Wheels Review #10492229

MAZDA MAZDA3 2010 car safety problem was reported on Jan 10, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . tl* the contact owns a 2010 mazda mazda3. the contact stated while driving various speeds the tire pressure warning light illuminated. after checking his vehicle the following morning, the driver's side nut that holds the valve stem had fractured. the vehicle was not inspected by a dealer or an independent mechanic. the manufacturer was not notified of the failure. the failure and current mileages was approximately 40,861. .0 person(s) were injured. 0 person(s) died.Mileage was 40861 miles. Vehicle Identification Number (VIN):JM1BL1SFXA1. Mazda Mazda3 2010 problem was reported in FRANKFORT, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Power Train

Mazda Mazda3 2010 Power Train Review #10496748

MAZDA MAZDA3 2010 car safety problem was reported on Jan 28, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . tl* the contact owns a 2010 mazda mazda3. the contact stated that while driving approximately 35 mph, the driver noticed a burning odor in the vehicle. additionally, the contact heard a clicking sound when driving at slow speeds. the vehicle was towed to the dealer for diagnostic testing. the technician stated that the clutch needed to be replaced. the vehicle was not repaired. the approximate failure mileage was 30,000. .Vehicle was on fire. 0 person(s) were injured. 0 person(s) died.Mileage was 30000 miles. Vehicle Identification Number (VIN):JM1BL1SF6A1. Mazda Mazda3 2010 problem was reported in CHARDON, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems Review #10497805

MAZDA MAZDA3 2010 car safety problem was reported on Feb 09, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS . my daughter was driving the mazda 3 headed east on i-94 in brookfield, wi near the moorland road exit on saturday afternoon, february 9, 2013 the car was moving at about 65mph. the low tire pressure warning light came on suddenly. then a few seconds after that the steering became wobbly and the right front tire blew. she was able to get control of the car, decelerate and pull to the shoulder. the right front tire outside sidewall was completely shredded. with the help of state trooper david w. hanson she got the tire changed. on monday, february 11, 2013 i took the car to a trusted mechanic. we found the tire valve and tire pressure sensor inside the shredded tire. the valve stem had blown into the tire. we didn't know what could have caused that. i had the mechanic, rob of erv's service in hartland, wi examine the other tires and valve stems on the remaining wheels of the car. he found another valve stem with a cracked housing that was ready to fail. i had the mechanic remove it and secure the valve stem. i retained the faulty parts. i believe the valve stem assembly failed causing the sudden loss of tire pressure, the shredding of the tire sidewall and near loss of control of the car. this could have resulted in a crash. injuries and possibly loss of life. *tr.Mileage was 25614 miles. Vehicle Identification Number (VIN):JM1BL1SF2A1. Mazda Mazda3 2010 problem was reported in HARTLAND, WI. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Mazda Mazda3 2010 Tires Review #10499940

MAZDA MAZDA3 2010 car safety problem was reported on Feb 01, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . tire pressure warning light came on, so i checked the pressure of each tire. one was low, so i asked my mechanic to fix it. he found the leak was a cracked valve stem assembly, allowing air to escape along the valve stem. fortunately it didn't damage the new tire, but still cost $150 to fix and i found this to be a common complaint for the mazda3. for me, the safety issue is having this problem happen when my wife is driving this car on a trip, sees the warning light come on, and has to find help to fix it or to change the tire for the spare, or the leak becomes fast enough to give her a flat tire. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 55000 miles. Vehicle Identification Number (VIN):JM1BL1SG4A1. Mazda Mazda3 2010 problem was reported in FOGELSVILLE, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10499940

MAZDA MAZDA3 2010 car safety problem was reported on Feb 01, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . tire pressure warning light came on, so i checked the pressure of each tire. one was low, so i asked my mechanic to fix it. he found the leak was a cracked valve stem assembly, allowing air to escape along the valve stem. fortunately it didn't damage the new tire, but still cost $150 to fix and i found this to be a common complaint for the mazda3. for me, the safety issue is having this problem happen when my wife is driving this car on a trip, sees the warning light come on, and has to find help to fix it or to change the tire for the spare, or the leak becomes fast enough to give her a flat tire. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 55000 miles. Vehicle Identification Number (VIN):JM1BL1SG4A1. Mazda Mazda3 2010 problem was reported in FOGELSVILLE, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Wheels Review #10501856

MAZDA MAZDA3 2010 car safety problem was reported on Mar 05, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . tl* the contact owns a 2010 mazda mazda3. the contact stated that while driving 65 mph, the tire pressure warning lamp illuminated and after inspecting the left rear tire, the contact noticed that the sleeve for the tire pressure sensor was corroded. the contact also noticed that both of the rear and the passenger side tire pressure sensor sleeves had developed cracks. the vehicle was taken to the dealer. the technician verified that the sensors were defective and corroded the inside of the tire. as a result, all four sensors and one of the tires needed to be replaced. the manufacturer was not made aware of the failure. the vehicle was repaired. the failure and current mileage was 58,000. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 58000 miles. Vehicle Identification Number (VIN):JM1BL1S64A1. Mazda Mazda3 2010 problem was reported in MIDDLEVILLE, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10501856

MAZDA MAZDA3 2010 car safety problem was reported on Mar 05, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . tl* the contact owns a 2010 mazda mazda3. the contact stated that while driving 65 mph, the tire pressure warning lamp illuminated and after inspecting the left rear tire, the contact noticed that the sleeve for the tire pressure sensor was corroded. the contact also noticed that both of the rear and the passenger side tire pressure sensor sleeves had developed cracks. the vehicle was taken to the dealer. the technician verified that the sensors were defective and corroded the inside of the tire. as a result, all four sensors and one of the tires needed to be replaced. the manufacturer was not made aware of the failure. the vehicle was repaired. the failure and current mileage was 58,000. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 58000 miles. Vehicle Identification Number (VIN):JM1BL1S64A1. Mazda Mazda3 2010 problem was reported in MIDDLEVILLE, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10503267

MAZDA MAZDA3 2010 car safety problem was reported on Mar 15, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . the vehicle involved is a 2010 mazda mazda3. i sat in the front drivers seat and felt the drivers seat shift backwards. from that point on the seat was unsteady and rocked forward and backward depending on which i was doing, accelerating or breaking. upon examination, it was found that the weld on the seat bracket had broken. in my opinion, this is a very unusual break and could be very hazardous if it happens upon braking. this issue happened on 03/15/13. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 46890 miles. Vehicle Identification Number (VIN):JM1BL1SG8A1. Mazda Mazda3 2010 problem was reported in NEW FAIRFIELD, CT. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Seats Review #10504097

MAZDA MAZDA3 2010 car safety problem was reported on Mar 21, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . while accelerating from a stop sign i hit a small pot hole and suddenly my seat flew back. the seat broke completely free from the mounting brackets at the two from mounting points. upon inspection the welds on the mounting bracket snapped clean off. due to the sudden reclining motion my neck was extremely sore from the sudden and abrupt rearward reclining motion this caused. if this were to happen on the highway to a person who is shorter then myself, loss of the control of the vehicle is very possible. once i was able to reach my destination i notified mazda who claims they have never heard of such a problem. upon further searching the internet i found many other mazda 3 owners are having the very same issues. i purchased the car brand new in july of 2009 and it has been maintained. i have not had any other issues with the vehicle. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 60900 miles. Vehicle Identification Number (VIN):JM1BL1SFXA1. Mazda Mazda3 2010 problem was reported in SOUTH BEND, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.

Mazda Mazda3 2010 Power Train

Mazda Mazda3 2010 Power Train Review #10504208

MAZDA MAZDA3 2010 car safety problem was reported on Mar 22, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . have had a situation occur about a dozen times since i purchased new in july 2010 with 93 miles - now at ~35500 miles. when coming to a stop on a cold engine that has only been running about 2-3 minutes, clutch pushed in to shift out of gear and brakes applied engine will rev to ~2500 rpm and it will stay there for about 3-4 seconds. first few times it happened i figured i hit the gas as well as the brake, after that i began to check my foot position on occurrence and my foot was nowhere near the accelerator. this has not caused any problems with a car accelerating on its own as it typically occurs as i am pushing the clutch in to come to a stop. only happens when the engine is still cold (generally the first stop of the day) and is very random when it occurs. have not brought to attention of dealership as there are no common factors to be able to reproduce the problem. upon notice of other complaints for this issue i wanted to add my own experience. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 35000 miles. Vehicle Identification Number (VIN):JM1BL1S55A1. Mazda Mazda3 2010 problem was reported in ATLANTA, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 10 mph.

Mazda Mazda3 2010 Engine

Mazda Mazda3 2010 Engine Review #10504208

MAZDA MAZDA3 2010 car safety problem was reported on Mar 22, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ENGINE . have had a situation occur about a dozen times since i purchased new in july 2010 with 93 miles - now at ~35500 miles. when coming to a stop on a cold engine that has only been running about 2-3 minutes, clutch pushed in to shift out of gear and brakes applied engine will rev to ~2500 rpm and it will stay there for about 3-4 seconds. first few times it happened i figured i hit the gas as well as the brake, after that i began to check my foot position on occurrence and my foot was nowhere near the accelerator. this has not caused any problems with a car accelerating on its own as it typically occurs as i am pushing the clutch in to come to a stop. only happens when the engine is still cold (generally the first stop of the day) and is very random when it occurs. have not brought to attention of dealership as there are no common factors to be able to reproduce the problem. upon notice of other complaints for this issue i wanted to add my own experience. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 35000 miles. Vehicle Identification Number (VIN):JM1BL1S55A1. Mazda Mazda3 2010 problem was reported in ATLANTA, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 10 mph.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10504603

MAZDA MAZDA3 2010 car safety problem was reported on Mar 01, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . while driving my mazda3, came to a stop, upon accelerating my seat began to rock slightly, about a week or so later, came to a stop and upon accelerating my whole seat rocked backwards, to the point i could no longer reach the pedals. took the car into the dealership and was told the welds that attach the seat to the seat track had broken. the seat is no longer stable and safe to drive. several calls into mazda, but getting no where because the car is out of warranty. obviously the welds connecting the seat to the seat track, and the subsequent breaking of those welds is a manufacturing defect that causes huge safety risks for all drivers of mazda3s. it is unknown where/when the welds will break. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 67000 miles. Vehicle Identification Number (VIN):JM1BL1SG6A1. Mazda Mazda3 2010 problem was reported in EAST SYRACUSE, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 5 mph.

Mazda Mazda3 2010 Seats Review #10505314

MAZDA MAZDA3 2010 car safety problem was reported on Apr 26, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . while coming off a turn at 35 mph and braking slightly, there was pop noise and the drivers side seat began to rock back and forth. once i had an opportunity to check the seat it had appeared that the welding of the seat had snapped and there was a piece of metal that was once part of the track that had snapped clean off. there was not an accident or hard braking. however, this seems to be a defect in the workmanship of the track that the seat sits on or how it is attached. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 51000 miles. Vehicle Identification Number (VIN):JM1BL1S65A1. Mazda Mazda3 2010 problem was reported in KING OF PRUSSIA, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Mazda Mazda3 2010 Seats Review #10507032

MAZDA MAZDA3 2010 car safety problem was reported on Mar 28, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . driver side seat appeared to have bad welding on the slider and it snapped. mazda has denied fixing the faulty seat, citing the warranty being expired. *tr.0 person(s) were injured. 0 person(s) died.Mazda Mazda3 2010 problem was reported in VISTA, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Seats Review #10508849

MAZDA MAZDA3 2010 car safety problem was reported on Apr 15, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . tl* the contact owns a 2010 mazda 3i. the contact stated that the driver's side seat would independently move back and forth when the contact was driving at any speed. the contact stated that the seat became separated from the base due to defective welding. the manufacturer was made aware of the failure. the vehicle was not repaired. the failure and current mileage was 81,160. .0 person(s) were injured. 0 person(s) died.Mileage was 81160 miles. Vehicle Identification Number (VIN):JM1BL1SG6A1. Mazda Mazda3 2010 problem was reported in CICERO, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10509718

MAZDA MAZDA3 2010 car safety problem was reported on Apr 26, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . checking tire pressure in driveway and tpms sensor - tire valve cracked and failed in 3 of 4 tires/wheels. two today, and the first approx. 3 months ago. imagine what could happen if one of these valves failed while . driving down the highway. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Vehicle Identification Number (VIN):JM1BL1H59A1. Mazda Mazda3 2010 problem was reported in MILFORD, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10509718

MAZDA MAZDA3 2010 car safety problem was reported on Apr 26, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . checking tire pressure in driveway and tpms sensor - tire valve cracked and failed in 3 of 4 tires/wheels. two today, and the first approx. 3 months ago. imagine what could happen if one of these valves failed while . driving down the highway. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Vehicle Identification Number (VIN):JM1BL1H59A1. Mazda Mazda3 2010 problem was reported in MILFORD, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10512593

MAZDA MAZDA3 2010 car safety problem was reported on May 06, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . on or about 4/24/2012, i had to purchase a new set of four tires at the firestone dealership on route 36, west long branch, nj 732-542-0995. please also note i had my mazda 3i for only a little over 2 years at that time. within the last year, i have already had to replace two of those tires due to leaks/blowouts. upon taking my car back to the self-same firestone dealership in west long branch, nj for closer inspection, ed gonzalez, the manager, indicated to me that the tire valve stem on the tire most recently "deceased"� (left rear) had actually fallen out of the tire and into the wheel well without ever being touched by anyone previously (i have photos of defective stems. upon closer inspection, the tire valve stem in the right rear tire is also defective to the eye. i have both defective stems and [xxx] will attest-in writing-to the fact that they are both defective-and the original, factory-installed tire valve stems that i received on my mazda 3i in february, 2010. information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6). *tr.0 person(s) were injured. 0 person(s) died.Mileage was 69500 miles. Vehicle Identification Number (VIN):JM1BL1SF2A1. Mazda Mazda3 2010 problem was reported in NEPTUNE, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 50 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10512593

MAZDA MAZDA3 2010 car safety problem was reported on May 06, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . on or about 4/24/2012, i had to purchase a new set of four tires at the firestone dealership on route 36, west long branch, nj 732-542-0995. please also note i had my mazda 3i for only a little over 2 years at that time. within the last year, i have already had to replace two of those tires due to leaks/blowouts. upon taking my car back to the self-same firestone dealership in west long branch, nj for closer inspection, ed gonzalez, the manager, indicated to me that the tire valve stem on the tire most recently "deceased"� (left rear) had actually fallen out of the tire and into the wheel well without ever being touched by anyone previously (i have photos of defective stems. upon closer inspection, the tire valve stem in the right rear tire is also defective to the eye. i have both defective stems and [xxx] will attest-in writing-to the fact that they are both defective-and the original, factory-installed tire valve stems that i received on my mazda 3i in february, 2010. information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6). *tr.0 person(s) were injured. 0 person(s) died.Mileage was 69500 miles. Vehicle Identification Number (VIN):JM1BL1SF2A1. Mazda Mazda3 2010 problem was reported in NEPTUNE, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 50 mph.

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems Review #10512660

MAZDA MAZDA3 2010 car safety problem was reported on May 18, 1985.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS . bought a used 2010 mazda 3 5-door in january 2013. i was driving down the highway on may 18th 2013 when i suddenly lost control of the vehicle, i cut off traffic to get into the emergency lane. noticed that the driver side front tire was flat, put on the spare and took car to the closest tire repair shop (good year tire). turns out that the tires tpms (tire-pressure monitoring system) sensors threads striped causing the sudden loss of air pressure in the tire. ironically the small little sensor that is supposed to prevent running on low air pressure was at fault in this traffic incident. *tr.Mazda Mazda3 2010 problem was reported in MILWAUKEE, WI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Tires Review #10512767

MAZDA MAZDA3 2010 car safety problem was reported on Apr 09, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . tl* the contact owns a 2010 mazda mazda3. the contact stated that the rear tire pressure sensors failed. the vehicle was taken to a dealer and it was found that the inside of the valve stems had rusted. the dealer determined that the valve stem needed to be replaced with a rubber stem instead of a metal one to prevent rust. the vehicle had not been repaired. the failure mileage was not available. the current mileage was 27,000. *tr.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1S6XA1. Mazda Mazda3 2010 problem was reported in EAST HARTFORD, CT. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10512767

MAZDA MAZDA3 2010 car safety problem was reported on Apr 09, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . tl* the contact owns a 2010 mazda mazda3. the contact stated that the rear tire pressure sensors failed. the vehicle was taken to a dealer and it was found that the inside of the valve stems had rusted. the dealer determined that the valve stem needed to be replaced with a rubber stem instead of a metal one to prevent rust. the vehicle had not been repaired. the failure mileage was not available. the current mileage was 27,000. *tr.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1S6XA1. Mazda Mazda3 2010 problem was reported in EAST HARTFORD, CT. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10514300

MAZDA MAZDA3 2010 car safety problem was reported on June 01, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with VISIBILITY/WIPER . my 2010 mazda 3 drives fine and does not have mechanical issues. the issue involves the interior dashboard. since it was made from some type of rubber, the sun has been melting it. aesthetically it doesn't look good, but while driving toward the direction of the sun, the glare it causes on my front windshield has been affecting my driving. i have spoken to a couple of people at a local mazda dealership and one ridiculous employee gave me recommendations such as to park my car in a garage, or under trees whenever possible. apart from those idiotic remarks, i will have to pay out-of-pocket due to the fact that i am now past my warranty. i previously owned a mitsubishi for 10 years and that never had issues along those lines. i have taken various photographs of how my vision is being obstructed and would happily send them to anyone i need to. the cheap rubber material used for the dashboard should not simply melt because of the sun. the sun will always be present, therefore these things should be taken into consideration during manufacturing. i would love to get this issue resolved before having to lose money and never deal with mazda again. overall i like the car, but i cannot stand the way the interior has diminished in such a short period of time. *tr.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF2A1. Mazda Mazda3 2010 problem was reported in CORAL GABLES, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Structure

Mazda Mazda3 2010 Structure Review #10514300

MAZDA MAZDA3 2010 car safety problem was reported on June 01, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with STRUCTURE . my 2010 mazda 3 drives fine and does not have mechanical issues. the issue involves the interior dashboard. since it was made from some type of rubber, the sun has been melting it. aesthetically it doesn't look good, but while driving toward the direction of the sun, the glare it causes on my front windshield has been affecting my driving. i have spoken to a couple of people at a local mazda dealership and one ridiculous employee gave me recommendations such as to park my car in a garage, or under trees whenever possible. apart from those idiotic remarks, i will have to pay out-of-pocket due to the fact that i am now past my warranty. i previously owned a mitsubishi for 10 years and that never had issues along those lines. i have taken various photographs of how my vision is being obstructed and would happily send them to anyone i need to. the cheap rubber material used for the dashboard should not simply melt because of the sun. the sun will always be present, therefore these things should be taken into consideration during manufacturing. i would love to get this issue resolved before having to lose money and never deal with mazda again. overall i like the car, but i cannot stand the way the interior has diminished in such a short period of time. *tr.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF2A1. Mazda Mazda3 2010 problem was reported in CORAL GABLES, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10514759

MAZDA MAZDA3 2010 car safety problem was reported on June 01, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . my tire pressure light was on, i stopped at the gas station to put some air in and as i removed the plastic valve cap the valve cracked and broke off leaving me with a flat tire. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 51546 miles. Mazda Mazda3 2010 problem was reported in PAWTUCKET, RI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10514759

MAZDA MAZDA3 2010 car safety problem was reported on June 01, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . my tire pressure light was on, i stopped at the gas station to put some air in and as i removed the plastic valve cap the valve cracked and broke off leaving me with a flat tire. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 51546 miles. Mazda Mazda3 2010 problem was reported in PAWTUCKET, RI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10514812

MAZDA MAZDA3 2010 car safety problem was reported on Apr 01, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with UNKNOWN OR OTHER . i have a 2010 mazda 3 with 38,000. the dashboard is melting. *tr.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF6A1. Mazda Mazda3 2010 problem was reported in NORTH PALM BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10516220

MAZDA MAZDA3 2010 car safety problem was reported on June 08, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . tl* the contact owns a 2010 mazda mazda 3. the contact stated that while driving approximately 55 mph, the tire pressure warning light illuminated. the contact inspected the vehicle and noticed that the rear passenger's side valve stem and sensor was corroded. the vehicle was taken to an independent mechanic where the valve stem was replaced. the vehicle was not repaired. the vin was not available. the approximate failure mileage was 80,000. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 80000 miles. Vehicle Identification Number (VIN):JM1BL1SG8A1. Mazda Mazda3 2010 problem was reported in BAYVILLE, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 55 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10516220

MAZDA MAZDA3 2010 car safety problem was reported on June 08, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . tl* the contact owns a 2010 mazda mazda 3. the contact stated that while driving approximately 55 mph, the tire pressure warning light illuminated. the contact inspected the vehicle and noticed that the rear passenger's side valve stem and sensor was corroded. the vehicle was taken to an independent mechanic where the valve stem was replaced. the vehicle was not repaired. the vin was not available. the approximate failure mileage was 80,000. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 80000 miles. Vehicle Identification Number (VIN):JM1BL1SG8A1. Mazda Mazda3 2010 problem was reported in BAYVILLE, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 55 mph.

Mazda Mazda3 2010 Electrical System

Mazda Mazda3 2010 Electrical System Review #10520401

MAZDA MAZDA3 2010 car safety problem was reported on June 15, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ELECTRICAL SYSTEM . tl* the contact owns a 2010 mazda3 . the contact stated while attempting to start the vehicle it failed to start with the illumination of all of the panel lights. the vehicle was towed to the dealer for diagnostic testing. the dealer stated the harness needed to be replaced. the vehicle was not repaired and the manufacturer was notified of the failure. the approximate failure mileage was 46,000. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 46000 miles. Vehicle Identification Number (VIN):JM1BL1SG7A1. Mazda Mazda3 2010 problem was reported in PASSAIC, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda3 2010 Engine

Mazda Mazda3 2010 Engine Review #10520401

MAZDA MAZDA3 2010 car safety problem was reported on June 15, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ENGINE . tl* the contact owns a 2010 mazda3 . the contact stated while attempting to start the vehicle it failed to start with the illumination of all of the panel lights. the vehicle was towed to the dealer for diagnostic testing. the dealer stated the harness needed to be replaced. the vehicle was not repaired and the manufacturer was notified of the failure. the approximate failure mileage was 46,000. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 46000 miles. Vehicle Identification Number (VIN):JM1BL1SG7A1. Mazda Mazda3 2010 problem was reported in PASSAIC, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda3 2010 Power Train

Mazda Mazda3 2010 Power Train Review #10520462

MAZDA MAZDA3 2010 car safety problem was reported on June 13, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . was driving on highway and rpm started to rev up, couldn't switch gears and clutch gave out from underneath me. luckily was able to roll off the highway when i noticed the problem. of course one problem leads to another battery then died at the shop, had to replace as well, this comes not even a month after the rotors for brakes hit the fan. this has got to be one of the most problematic cars i have seen. a clutch dying less then 3 years is very strange and has happened to others as well with this model. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 26000 miles. Vehicle Identification Number (VIN):JM1BL1S60A1. Mazda Mazda3 2010 problem was reported in TUSTIN, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10521349

MAZDA MAZDA3 2010 car safety problem was reported on June 22, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . tire pressure monitoring system sensor failed causing the tire to blowout and go flat on the highway. the stem of the sensor was corroded which caused the incident. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 49000 miles. Mazda Mazda3 2010 problem was reported in QUINCY, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10521349

MAZDA MAZDA3 2010 car safety problem was reported on June 22, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . tire pressure monitoring system sensor failed causing the tire to blowout and go flat on the highway. the stem of the sensor was corroded which caused the incident. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 49000 miles. Mazda Mazda3 2010 problem was reported in QUINCY, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10525030

MAZDA MAZDA3 2010 car safety problem was reported on July 13, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . the documented date above (07/13/13) is my most recent incident with my valve stem/tire pressure monitoring system falling off while driving. in june 2012 with ~34,000 miles, while driving on the highway, my first valve stem/tpms fell out, not being able to drive on that wheel (no air), and the wheel could no longer be used until i had a mazda dealer replace the part. this was a very dangerous experience for my tire to suddenly deflate while moving at fast speeds. this was fixed under my almost terminated warranty. one month later, the valve stem/tpms on another wheel came off while driving and this had to be replaced like the other one. most recently, my third wheel tpmsensor went while also driving on the highway, vigilantly maintaining control on my vehicle until i could pull off the highway. this trend shows a huge safety issue/inadequate parts used during construction. there is no prescribed care for these parts in the mazda owners manual nor is there anyway to know that these would malfunction until they did. 3 out of 4 is unacceptable and unsafe and should show a trend. when i called mazda, they told me that the cost of this recent repair was mine because the vehicle, now at ~55,000 miles was no longer under warranty. these parts were dysfunctional from the beginning and should have all been replaced at my first incident if this was to happen again, and again. i am nervous that this could happen to my fourth wheel while driving, potentially causing an accident. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 55000 miles. Vehicle Identification Number (VIN):JM1BL1SG7A1. Mazda Mazda3 2010 problem was reported in WAKEFIELD, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 55 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10525030

MAZDA MAZDA3 2010 car safety problem was reported on July 13, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . the documented date above (07/13/13) is my most recent incident with my valve stem/tire pressure monitoring system falling off while driving. in june 2012 with ~34,000 miles, while driving on the highway, my first valve stem/tpms fell out, not being able to drive on that wheel (no air), and the wheel could no longer be used until i had a mazda dealer replace the part. this was a very dangerous experience for my tire to suddenly deflate while moving at fast speeds. this was fixed under my almost terminated warranty. one month later, the valve stem/tpms on another wheel came off while driving and this had to be replaced like the other one. most recently, my third wheel tpmsensor went while also driving on the highway, vigilantly maintaining control on my vehicle until i could pull off the highway. this trend shows a huge safety issue/inadequate parts used during construction. there is no prescribed care for these parts in the mazda owners manual nor is there anyway to know that these would malfunction until they did. 3 out of 4 is unacceptable and unsafe and should show a trend. when i called mazda, they told me that the cost of this recent repair was mine because the vehicle, now at ~55,000 miles was no longer under warranty. these parts were dysfunctional from the beginning and should have all been replaced at my first incident if this was to happen again, and again. i am nervous that this could happen to my fourth wheel while driving, potentially causing an accident. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 55000 miles. Vehicle Identification Number (VIN):JM1BL1SG7A1. Mazda Mazda3 2010 problem was reported in WAKEFIELD, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 55 mph.

Mazda Mazda3 2010 Wheels Review #10525181

MAZDA MAZDA3 2010 car safety problem was reported on July 09, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . tpms alerted driver to low air pressure in a tire. checked tire, pressure low (subsequently found screw in tire). once air nozzle place on valve stem, it snapped in half and all the air immediately went out of the tire. others checked and are corroded and brittle. dealer and local auto mechanic both stated likely to happen again without warning. materials used in the valve stem should be changed to make them flexible, like the older ones without the monitoring system. replaced valve stem with $5 stem of flexible material to prevent safety issue in the future. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 32750 miles. Mazda Mazda3 2010 problem was reported in WINTHROP, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10525181

MAZDA MAZDA3 2010 car safety problem was reported on July 09, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . tpms alerted driver to low air pressure in a tire. checked tire, pressure low (subsequently found screw in tire). once air nozzle place on valve stem, it snapped in half and all the air immediately went out of the tire. others checked and are corroded and brittle. dealer and local auto mechanic both stated likely to happen again without warning. materials used in the valve stem should be changed to make them flexible, like the older ones without the monitoring system. replaced valve stem with $5 stem of flexible material to prevent safety issue in the future. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 32750 miles. Mazda Mazda3 2010 problem was reported in WINTHROP, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems Review #10525478

MAZDA MAZDA3 2010 car safety problem was reported on July 14, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS . while checking a customer's tire pressure the tpms sensor broke causing all air to escape the tire, immobilizing the vehicle. we had a new tpms sensor installed and the tire repaired for $81.41. *tr.Mileage was 76111 miles. Vehicle Identification Number (VIN):JM1BL1SG9A1. Mazda Mazda3 2010 problem was reported in PLEASANTON, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10531519

MAZDA MAZDA3 2010 car safety problem was reported on July 11, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . only owner of a 2010 mazda 3. issues with car since purchasing. replaced tires in winter of 2012, few weeks later tire pressure light came on. filled tires with air. few weeks later, same occurrence. brought car to the place were the tires were professionally installed. the inspected over all 4 tires and found that 2 of the 4 tire stems needed to be replaced. called mazda corp and they stated the car needed to go to a dealership to be diagnosed. ( for leaking tire stems ). called my local mazda where the car was purchased, they were great and said they wouldn't charge a fee to diagnose leaking stems as it was obvious. they did find that 2 of the 4 were broken. 1 was actually snapped in half. no driver error noted, or damage to rim. if you google this issue there are other complaints out there regarding this, but mazda still wont recognize this as a safety issue. my question being... what if the stems failed at a high rate of speed ???? *tr.0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Vehicle Identification Number (VIN):JM1BL1SG5A1. Mazda Mazda3 2010 problem was reported in PORT JERVIS, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10531519

MAZDA MAZDA3 2010 car safety problem was reported on July 11, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . only owner of a 2010 mazda 3. issues with car since purchasing. replaced tires in winter of 2012, few weeks later tire pressure light came on. filled tires with air. few weeks later, same occurrence. brought car to the place were the tires were professionally installed. the inspected over all 4 tires and found that 2 of the 4 tire stems needed to be replaced. called mazda corp and they stated the car needed to go to a dealership to be diagnosed. ( for leaking tire stems ). called my local mazda where the car was purchased, they were great and said they wouldn't charge a fee to diagnose leaking stems as it was obvious. they did find that 2 of the 4 were broken. 1 was actually snapped in half. no driver error noted, or damage to rim. if you google this issue there are other complaints out there regarding this, but mazda still wont recognize this as a safety issue. my question being... what if the stems failed at a high rate of speed ???? *tr.0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Vehicle Identification Number (VIN):JM1BL1SG5A1. Mazda Mazda3 2010 problem was reported in PORT JERVIS, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10531763

MAZDA MAZDA3 2010 car safety problem was reported on Mar 15, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . i have a 2010 mazda 3, i have had issues with the tire pressure sensor corroding and causing the tire to lose air quickly. this has happen to me twice within 6 months of each other. i took the other two tire sensors off, which they were also corroded. this issue needs to be addressed as quickly as possible, i got lucky that i wasn't traveling at high speeds at the time my pressure in my tires went out. also at the time i had two children under the age of 5 in the car which thank goodness nothing happen to them! this could very easily cause someone to loose control and wreck their car and cause serious injuries. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 68000 miles. Vehicle Identification Number (VIN):JM1BL1SG2A1. Mazda Mazda3 2010 problem was reported in STERLING, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 45 mph.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10531763

MAZDA MAZDA3 2010 car safety problem was reported on Mar 15, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . i have a 2010 mazda 3, i have had issues with the tire pressure sensor corroding and causing the tire to lose air quickly. this has happen to me twice within 6 months of each other. i took the other two tire sensors off, which they were also corroded. this issue needs to be addressed as quickly as possible, i got lucky that i wasn't traveling at high speeds at the time my pressure in my tires went out. also at the time i had two children under the age of 5 in the car which thank goodness nothing happen to them! this could very easily cause someone to loose control and wreck their car and cause serious injuries. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 68000 miles. Vehicle Identification Number (VIN):JM1BL1SG2A1. Mazda Mazda3 2010 problem was reported in STERLING, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 45 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10531766

MAZDA MAZDA3 2010 car safety problem was reported on July 25, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . tl* the contact owns a 2010 mazda3. the contact stated that while driving 50 mph, the rear passenger's side tire went flat with the illumination of the tire sensor warning light. the vehicle was taken to an independent mechanic for diagnosis where it was stated that the tire sensors were corroded. the vehicle was repaired and the manufacturer was notified. the approximate failure mileage was 65,000. .0 person(s) were injured. 0 person(s) died.Mileage was 65000 miles. Vehicle Identification Number (VIN):JM1BL1SG2A1. Mazda Mazda3 2010 problem was reported in STEERLING, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 50 mph.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10532543

MAZDA MAZDA3 2010 car safety problem was reported on July 18, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . within 2 days of driving, my mazda 3 had two separate incidents, where the valves of the tire pressure monitoring system (tpms) failed, on two separate tires. on monday, july 18, 2013 while traveling at highway speed on rt. 25 in bourne, ma, the tire pressure warning light came on. i stopped at the nearest gas station. the driver's front tire was very flat. when i attempted to fill it with air, the valve pushed into the tire. luckily, i was at a gas station and they were able to repair the tire with "standard" (non-tpms) valve and i was on my way. as i was on vacation. i parked the car for a week. when i returned to my car (july 22), i drove the car for about 50 miles. i stopped to have lunch and noticed that the driver's side rear tire was very flat. when i attempted to put air into the valve, it too pushed into the tire. that is two tpms valves that failed in two days of driving. i called mazda customer service (800-222-5500, ext. 6) explained the situation to jose (ext. 1180). he was sympathetic, but would not commit to mazda repairing the tpms valve at no cost to me. i am having my mechanic put in non-tpms valves in the remaining two tires on the car, as i feel they are a real safety hazard. i will not drive the car until it is repaired. i went on to the internet and there are numerous instances of valve failures on mazda3 cars (http://carproblemzoo.com/mazda/mazda3/tire-pressure-monitoring-system-problems.php). i plan to take the failed components to wellsley mazda, in wellsley ma where the vehicle was purchased, for evaluation. i do not trust the reliability of the tmps system in my mazda3, and apparently there are others who feel the same. the failure of the tpms valves is a serious safety issue and one that the nhtsa should consider investigating. tire failure at highway speed can lead to very serious accidents. .Mileage was 45800 miles. Vehicle Identification Number (VIN):JM1BL1H60A1. Mazda Mazda3 2010 problem was reported in CHELMSFORD, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems Review #10532543

MAZDA MAZDA3 2010 car safety problem was reported on July 18, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS . within 2 days of driving, my mazda 3 had two separate incidents, where the valves of the tire pressure monitoring system (tpms) failed, on two separate tires. on monday, july 18, 2013 while traveling at highway speed on rt. 25 in bourne, ma, the tire pressure warning light came on. i stopped at the nearest gas station. the driver's front tire was very flat. when i attempted to fill it with air, the valve pushed into the tire. luckily, i was at a gas station and they were able to repair the tire with "standard" (non-tpms) valve and i was on my way. as i was on vacation. i parked the car for a week. when i returned to my car (july 22), i drove the car for about 50 miles. i stopped to have lunch and noticed that the driver's side rear tire was very flat. when i attempted to put air into the valve, it too pushed into the tire. that is two tpms valves that failed in two days of driving. i called mazda customer service (800-222-5500, ext. 6) explained the situation to jose (ext. 1180). he was sympathetic, but would not commit to mazda repairing the tpms valve at no cost to me. i am having my mechanic put in non-tpms valves in the remaining two tires on the car, as i feel they are a real safety hazard. i will not drive the car until it is repaired. i went on to the internet and there are numerous instances of valve failures on mazda3 cars (http://carproblemzoo.com/mazda/mazda3/tire-pressure-monitoring-system-problems.php). i plan to take the failed components to wellsley mazda, in wellsley ma where the vehicle was purchased, for evaluation. i do not trust the reliability of the tmps system in my mazda3, and apparently there are others who feel the same. the failure of the tpms valves is a serious safety issue and one that the nhtsa should consider investigating. tire failure at highway speed can lead to very serious accidents. .Mileage was 45800 miles. Vehicle Identification Number (VIN):JM1BL1H60A1. Mazda Mazda3 2010 problem was reported in CHELMSFORD, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10532543

MAZDA MAZDA3 2010 car safety problem was reported on July 18, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . within 2 days of driving, my mazda 3 had two separate incidents, where the valves of the tire pressure monitoring system (tpms) failed, on two separate tires. on monday, july 18, 2013 while traveling at highway speed on rt. 25 in bourne, ma, the tire pressure warning light came on. i stopped at the nearest gas station. the driver's front tire was very flat. when i attempted to fill it with air, the valve pushed into the tire. luckily, i was at a gas station and they were able to repair the tire with "standard" (non-tpms) valve and i was on my way. as i was on vacation. i parked the car for a week. when i returned to my car (july 22), i drove the car for about 50 miles. i stopped to have lunch and noticed that the driver's side rear tire was very flat. when i attempted to put air into the valve, it too pushed into the tire. that is two tpms valves that failed in two days of driving. i called mazda customer service (800-222-5500, ext. 6) explained the situation to jose (ext. 1180). he was sympathetic, but would not commit to mazda repairing the tpms valve at no cost to me. i am having my mechanic put in non-tpms valves in the remaining two tires on the car, as i feel they are a real safety hazard. i will not drive the car until it is repaired. i went on to the internet and there are numerous instances of valve failures on mazda3 cars (http://carproblemzoo.com/mazda/mazda3/tire-pressure-monitoring-system-problems.php). i plan to take the failed components to wellsley mazda, in wellsley ma where the vehicle was purchased, for evaluation. i do not trust the reliability of the tmps system in my mazda3, and apparently there are others who feel the same. the failure of the tpms valves is a serious safety issue and one that the nhtsa should consider investigating. tire failure at highway speed can lead to very serious accidents. .Mileage was 45800 miles. Vehicle Identification Number (VIN):JM1BL1H60A1. Mazda Mazda3 2010 problem was reported in CHELMSFORD, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Mazda Mazda3 2010 Electrical System

Mazda Mazda3 2010 Electrical System Review #10536017

MAZDA MAZDA3 2010 car safety problem was reported on Aug 09, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ELECTRICAL SYSTEM . vehicle lost power multiple times shuddering on the road. faulty wiring harness was discovered by the dealership. this issue was present on previously produced mazda 3s for the year but the dealership stated that this particular vin didn't fall into the production numbers for the recall. this issue seems to be present on more cars than just the 25,000 that were recalled in 2009. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 79000 miles. Vehicle Identification Number (VIN):JM1BL1S55A1. Mazda Mazda3 2010 problem was reported in FARMINGTON HILLS, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10536323

MAZDA MAZDA3 2010 car safety problem was reported on July 11, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . noticed movement/loose drivers seat, took to dealer, said basic warranty had expired, but mileage low so mazda may cover. mazda covering part, but not labor. the seat is loose, bracket is cracked that holds seat. is this a safety issue that should be covered under the safety warranty? *tr.0 person(s) were injured. 0 person(s) died.Mileage was 33000 miles. Vehicle Identification Number (VIN):JM1BL1H69A1. Mazda Mazda3 2010 problem was reported in FOSTER CITY, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10537540

MAZDA MAZDA3 2010 car safety problem was reported on Aug 16, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . tl* the contact owns a 2010 mazda, mazda3. the contact stated that while having the vehicle serviced, the technician advised that the motor mount was cracked and needed to be replaced. also, the contact mentioned that the front driver's side tire went flat with the illumination of the tire sensor warning light. the vehicle was taken to a private mechanic where it was diagnosed that the tire sensors were corroded and needed to be replaced. the manufacturer was notified of the failure. the vehicle was repaired. the approximate failure and current mileage was 76,000. .0 person(s) were injured. 0 person(s) died.Mileage was 76000 miles. Vehicle Identification Number (VIN):JM1BL1SG6A1. Mazda Mazda3 2010 problem was reported in LAKE TELEMARK, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Engine

Mazda Mazda3 2010 Engine Review #10537540

MAZDA MAZDA3 2010 car safety problem was reported on Aug 16, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ENGINE . tl* the contact owns a 2010 mazda, mazda3. the contact stated that while having the vehicle serviced, the technician advised that the motor mount was cracked and needed to be replaced. also, the contact mentioned that the front driver's side tire went flat with the illumination of the tire sensor warning light. the vehicle was taken to a private mechanic where it was diagnosed that the tire sensors were corroded and needed to be replaced. the manufacturer was notified of the failure. the vehicle was repaired. the approximate failure and current mileage was 76,000. .0 person(s) were injured. 0 person(s) died.Mileage was 76000 miles. Vehicle Identification Number (VIN):JM1BL1SG6A1. Mazda Mazda3 2010 problem was reported in LAKE TELEMARK, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Steering

Mazda Mazda3 2010 Steering Review #10542133

MAZDA MAZDA3 2010 car safety problem was reported on Sept 05, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with STEERING . parked car after short drive. when restarted catastrophic power steering failure very similar in symptoms of the recall for models as late as 2009. would not be surprised to find a 2009 part in the car. the car is not drivable except by person with ample upper body strength to man-handle steering and is a significant safety hazard. *jb.0 person(s) were injured. 0 person(s) died.Mileage was 69958 miles. Vehicle Identification Number (VIN):JM1BL1SF0A1. Mazda Mazda3 2010 problem was reported in GEORGETOWN, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10542204

MAZDA MAZDA3 2010 car safety problem was reported on Aug 01, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . as i was driving i felt an unease movement of the driver's seat. suddenly it started a kind of a "rocking chair" movement. then it felt like something snapped and broke. i move my self forward to keep control of the car and stopped. as soon as i raised my body from the seat i completetly fell backwards. as i looked under the seat there was a piece of metal covered with a clean type of grease or lubricant of about 4" long laying under my seat. .0 person(s) were injured. 0 person(s) died.Mileage was 65000 miles. Vehicle Identification Number (VIN):JM1BL1H50A1. Mazda Mazda3 2010 problem was reported in BARCELONETA, PR. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Mazda Mazda3 2010 Electronic Stability Control

Mazda Mazda3 2010 Electronic Stability Control Review #10545048

MAZDA MAZDA3 2010 car safety problem was reported on Sept 23, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ELECTRONIC STABILITY CONTROL . i was driving to work. road was wet. vehicle gets in front of me and i had to turn quick to avoid hitting this vehicle. i lost control, luckily no one was injured. i know dsc is not supposed to replace a safe driver, but in an emergency situation like this it should of at least helped me out. it turned completely off. the dsc light came on permanently as well as the abs light and the brake light. after turning the vehicle off then back on the lights came off. when i took the car to the mazda dealer and was completely ignored by the service department as to the system having any problem at all. so i decide to go to an empty parking lot and tried to repeat the same emergency situation i was and indeed the system failed again. i went back to the mazda dealer and showed them, and apparently the only solution to them is replace the dsc module. this would of been suficient for me if the system wasn't $700, and since my vehicle has 50000 miles on it and i no longer have their initial warranty effective, then it's a must strive situation. the only reason i'm complaining is because of the poor quality of this system, the hazardous situation it could compromise mazda drivers and others around them, and the fact that mazda is ignoring this despite thousands of customers complaining. .0 person(s) were injured. 0 person(s) died.Mileage was 53266 miles. Vehicle Identification Number (VIN):JM1BL1SF4A1. Mazda Mazda3 2010 problem was reported in SAINT PETERSBURG, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Mazda Mazda3 2010 Service Brakes

Mazda Mazda3 2010 Service Brakes Review #10545048

MAZDA MAZDA3 2010 car safety problem was reported on Sept 23, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SERVICE BRAKES . i was driving to work. road was wet. vehicle gets in front of me and i had to turn quick to avoid hitting this vehicle. i lost control, luckily no one was injured. i know dsc is not supposed to replace a safe driver, but in an emergency situation like this it should of at least helped me out. it turned completely off. the dsc light came on permanently as well as the abs light and the brake light. after turning the vehicle off then back on the lights came off. when i took the car to the mazda dealer and was completely ignored by the service department as to the system having any problem at all. so i decide to go to an empty parking lot and tried to repeat the same emergency situation i was and indeed the system failed again. i went back to the mazda dealer and showed them, and apparently the only solution to them is replace the dsc module. this would of been suficient for me if the system wasn't $700, and since my vehicle has 50000 miles on it and i no longer have their initial warranty effective, then it's a must strive situation. the only reason i'm complaining is because of the poor quality of this system, the hazardous situation it could compromise mazda drivers and others around them, and the fact that mazda is ignoring this despite thousands of customers complaining. .0 person(s) were injured. 0 person(s) died.Mileage was 53266 miles. Vehicle Identification Number (VIN):JM1BL1SF4A1. Mazda Mazda3 2010 problem was reported in SAINT PETERSBURG, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10547956

MAZDA MAZDA3 2010 car safety problem was reported on June 09, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with TIRES . june 9th 2013, vehicle experienced loss of inflation pressure in passenger front tire while driving. dealership confirmed tpms valve seal failure was root cause of air loss. check of other tpm sensors confirmed driver side front seal was also defective and leaking small amounts of air. both replaced under warranty with dealer indicating this as a known issue. september 16th 2013 passenger rear tire experienced airloss while driving vehicle. dealer investigation confirmed tpm valve failure. part not covered under warranty or dealer goodwill. failure of safety-critical part after ~3 years of field exposure is not acceptable. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 35000 miles. Vehicle Identification Number (VIN):JM1BL1S55A1. Mazda Mazda3 2010 problem was reported in MT. JULIET, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10547956

MAZDA MAZDA3 2010 car safety problem was reported on June 09, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . june 9th 2013, vehicle experienced loss of inflation pressure in passenger front tire while driving. dealership confirmed tpms valve seal failure was root cause of air loss. check of other tpm sensors confirmed driver side front seal was also defective and leaking small amounts of air. both replaced under warranty with dealer indicating this as a known issue. september 16th 2013 passenger rear tire experienced airloss while driving vehicle. dealer investigation confirmed tpm valve failure. part not covered under warranty or dealer goodwill. failure of safety-critical part after ~3 years of field exposure is not acceptable. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 35000 miles. Vehicle Identification Number (VIN):JM1BL1S55A1. Mazda Mazda3 2010 problem was reported in MT. JULIET, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Mazda Mazda3 2010 Exterior Lighting

Mazda Mazda3 2010 Exterior Lighting Review #10548296

MAZDA MAZDA3 2010 car safety problem was reported on Apr 02, 2012.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with EXTERIOR LIGHTING . water intrusion and condensation build-up inside the headlamp assembly causing major damage and required whole unit replacement. usually happen after a rainstorm or car wash. this had occurred to both headlamps on my vehicle. the first incident happened in april 2012 to the passenger-side headlamp assembly after i washed the vehicle. the last incident happened in october 2013 to the driver-side headlamp assembly after a rain storm. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 43000 miles. Vehicle Identification Number (VIN):JM1BL1H69A1. Mazda Mazda3 2010 problem was reported in CORONA, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Steering

Mazda Mazda3 2010 Steering Review #10552825

MAZDA MAZDA3 2010 car safety problem was reported on Nov 18, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with STEERING . power steering assist light came on and stayed on. car was very hard to steer. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 53400 miles. Mazda Mazda3 2010 problem was reported in KINGSPORT, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 10 mph.

Mazda Mazda3 2010 Steering Review #10553226

MAZDA MAZDA3 2010 car safety problem was reported on Nov 18, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with STEERING . tl* the contact owns a 2010 mazda, mazda3. the contact was driving 35 mph when the power steering warning lamp illuminated as the power steering assist failed. the vehicle was taken to a dealer for inspection. the contact was informed that the power steering assist module was failing and that the failure could recur sporadically. the vehicle was not repaired. the manufacturer was made aware of the incident. the approximate failure mileage was 54,000. .0 person(s) were injured. 0 person(s) died.Mileage was 54000 miles. Vehicle Identification Number (VIN):JM1BL1SF9A1. Mazda Mazda3 2010 problem was reported in KINGSPORT, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Mazda Mazda3 2010 Exterior Lighting

Mazda Mazda3 2010 Exterior Lighting Review #10554823

MAZDA MAZDA3 2010 car safety problem was reported on Nov 01, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with EXTERIOR LIGHTING . condensation formed inside drivers headlight causing a failure of the drivers side hid (xenon) headlight and ballast. existing tsb (nhtsa reference #10037655 tsb reference #sb-09-057-10) for this condition. this needs to be upgraded to a recall so mazda cannot refuse repair due to out of warranty vehicles for time/mileage. this is a known defect as shown in the above referenced tsb and mazda is refusing to fix when vehicle is out of the 3yr/36,000 mile warranty. corporate mazda has been in contact with local dealership which has verified that hid lamp/ballast failure was directly caused with condensation from above referenced tsb. after verification from local dealership, mazda corporate (800-222-5500) refuses to assist with getting vehicle fixed and operating correctly and safely. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 90000 miles. Vehicle Identification Number (VIN):JM1BL1S55A1. Mazda Mazda3 2010 problem was reported in HEBRON, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Service Brakes, Hydraulic

Mazda Mazda3 2010 Service Brakes, Hydraulic Review #10556685

MAZDA MAZDA3 2010 car safety problem was reported on Dec 02, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SERVICE BRAKES, HYDRAULIC . 2010 mazda 3. consumer writes in regards to vehicle tires, softness of the brake and resurfacing rotors. *smd the consumer stated a visual inspection revealed the transmission fluid needed to be replaced, the tires were wearing unevenly, and the vehicle pulled to the left. also, the battery was replaced. .Vehicle Identification Number (VIN):JM1BL1S5XA1. Mazda Mazda3 2010 problem was reported in LAFAYETTE, IN. Vehicle was purchased on Nov 08, 2013. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. DEALER'S NAME: GUARANTEED TRANSMISSION SERVICE . DEALER'S TELEPHONE NUMBER: 765-447-6012 . DEALER'S CITY: LAFAYETTE . DEALER'S STATE CODE: IN. DEALER'S ZIPCODE: 47905 .

Mazda Mazda3 2010 Suspension

Mazda Mazda3 2010 Suspension Review #10556685

MAZDA MAZDA3 2010 car safety problem was reported on Dec 02, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SUSPENSION . 2010 mazda 3. consumer writes in regards to vehicle tires, softness of the brake and resurfacing rotors. *smd the consumer stated a visual inspection revealed the transmission fluid needed to be replaced, the tires were wearing unevenly, and the vehicle pulled to the left. also, the battery was replaced. .Vehicle Identification Number (VIN):JM1BL1S5XA1. Mazda Mazda3 2010 problem was reported in LAFAYETTE, IN. Vehicle was purchased on Nov 08, 2013. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. DEALER'S NAME: GUARANTEED TRANSMISSION SERVICE . DEALER'S TELEPHONE NUMBER: 765-447-6012 . DEALER'S CITY: LAFAYETTE . DEALER'S STATE CODE: IN. DEALER'S ZIPCODE: 47905 .

Mazda Mazda3 2010 Power Train

Mazda Mazda3 2010 Power Train Review #10556685

MAZDA MAZDA3 2010 car safety problem was reported on Dec 02, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . 2010 mazda 3. consumer writes in regards to vehicle tires, softness of the brake and resurfacing rotors. *smd the consumer stated a visual inspection revealed the transmission fluid needed to be replaced, the tires were wearing unevenly, and the vehicle pulled to the left. also, the battery was replaced. .Vehicle Identification Number (VIN):JM1BL1S5XA1. Mazda Mazda3 2010 problem was reported in LAFAYETTE, IN. Vehicle was purchased on Nov 08, 2013. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. DEALER'S NAME: GUARANTEED TRANSMISSION SERVICE . DEALER'S TELEPHONE NUMBER: 765-447-6012 . DEALER'S CITY: LAFAYETTE . DEALER'S STATE CODE: IN. DEALER'S ZIPCODE: 47905 .

Mazda Mazda3 2010 Electrical System Battery

Mazda Mazda3 2010 Electrical System Battery Review #10556685

MAZDA MAZDA3 2010 car safety problem was reported on Dec 02, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with ELECTRICAL SYSTEM:BATTERY . 2010 mazda 3. consumer writes in regards to vehicle tires, softness of the brake and resurfacing rotors. *smd the consumer stated a visual inspection revealed the transmission fluid needed to be replaced, the tires were wearing unevenly, and the vehicle pulled to the left. also, the battery was replaced. .Vehicle Identification Number (VIN):JM1BL1S5XA1. Mazda Mazda3 2010 problem was reported in LAFAYETTE, IN. Vehicle was purchased on Nov 08, 2013. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. DEALER'S NAME: GUARANTEED TRANSMISSION SERVICE . DEALER'S TELEPHONE NUMBER: 765-447-6012 . DEALER'S CITY: LAFAYETTE . DEALER'S STATE CODE: IN. DEALER'S ZIPCODE: 47905 .

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10558911

MAZDA MAZDA3 2010 car safety problem was reported on Jan 07, 2014.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . driver seat is loose and moves during braking or turning a corner. this can make it hard to control the vehicle. if this would break loose during a crash how would this effect air bag operation. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 57000 miles. Vehicle Identification Number (VIN):JM1BL1SF0A1. Mazda Mazda3 2010 problem was reported in CUYAHOGA FALLS, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 25 mph.

Mazda Mazda3 2010 Exterior Lighting

Mazda Mazda3 2010 Exterior Lighting Review #10558974

MAZDA MAZDA3 2010 car safety problem was reported on Nov 06, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with EXTERIOR LIGHTING . both headlights shorted out at the same time. one minute they worked and the next the did not. had to wait to move car and take to dealership till day light since this happened in the dark. luckily we had stopped so they did not fail while driving. found out upon inspection this is a problem due to the moisture the headlamp case allows inside. we had complained about this moisture previously back in 2011 and 2012. we had been informed it was a defect just as we had been told with our 2004 mazda 3. interesting enough we find out that in the 11 times our vehicle was serviced at galpin mazda in 2012 there had been a service bulletins on this exact issue and recommended to replace the defective headlamps. galpin did nothing. never even mentioned anything but simply responded with " its a known defect." service bulletin #sb-09-003-13. another service bulletin #09-005-11, and another #sb-09-057-10. upon speaking to other mazda mechanics, we learned this has been an ongoing issue. we had experienced it for years with our 2004 as stated previously but never realized it was the inside condensation causing the bulb to blow. the fact that mazda knowingly continued manufacturing these defective headlamp casings and never recalled them is unacceptable. what if we had been driving when they failed? as it was we have spent 2 months now dealing with both mazda and galpin, who both want to wash their hands of any wrong doing. this is unacceptable. this is a safety issue. mazda knows it. dealers know it, yet it is allowed to continue. the cost to replace the parts now are over 3 thousand dollars. we are supposed to pay for their constant and knowing errors. that is not acceptable and they need to be stopped and made to fix this problem before somebody dies in an accident with them failing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 148000 miles. Vehicle Identification Number (VIN):JM1BL1S64A1. Mazda Mazda3 2010 problem was reported in CASTAIC, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10561761

MAZDA MAZDA3 2010 car safety problem was reported on Jan 27, 2014.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . entered the vehicle to go to work. sat down in the driver's seat, immediately heard a pop and the seat became unsteady (wobbly). after work i looked at the bottom of the seat and saw that a weld broke loose from a bar that stabilizes the seat. it is very disconcerting to the driver while operating the vehicle and may contribute to the possibility of future crashes. the safety of the seat during a crash scenario is compromised. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 68000 miles. Vehicle Identification Number (VIN):JM1BL1S64A1. Mazda Mazda3 2010 problem was reported in MARYSVILLE, WA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10561881

MAZDA MAZDA3 2010 car safety problem was reported on Jan 07, 2014.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . tl* the contact owns a 2010 mazda mazda3. the contact stated that while driving approximately 20 mph, she heard an unusual noise outside of the vehicle. the vehicle was maneuvered to the side of the road to inspect the vehicle. the contact noticed the driver's side rear tire pressure monitor sensor was faulty and caused the tire to deflate. the tire was replaced with a spare tire. the vehicle was taken to a dealer for repair. the contact wanted to include that if she were traveling at greats speeds the failure could have been hazardous. the manufacturer was notified of the problem. the approximate failure mileage was 15,850. .0 person(s) were injured. 0 person(s) died.Mileage was 15850 miles. Vehicle Identification Number (VIN):JM1BL1S57A1. Mazda Mazda3 2010 problem was reported in PARMA HEIGHTS, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 20 mph.

Mazda Mazda3 2010 Power Train

Mazda Mazda3 2010 Power Train Review #10563914

MAZDA MAZDA3 2010 car safety problem was reported on Feb 06, 2014.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with POWER TRAIN . clutch failure while driving resulting in difficulty steering and loss of control of the vehicle. as the care had a low mileage and is new you are not expecting this kind of problem. need to investigate why these clutches are failing, specifically in the 2010 model. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 31700 miles. Mazda Mazda3 2010 problem was reported in BUFFALO, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10566252

MAZDA MAZDA3 2010 car safety problem was reported on Feb 20, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with TIRES . rear tire was flat in the morning. could not find visible damage. pumped it up to 32 psi and by next morning it was 20 psi. three days later, a front tire was flat. no noticeable damage, but did notice a cracked tire stem on a third tire. went to a tire dealer to get repairs. was informed that three of my four tire pressure monitor sensors were leaking. had all four replaced at my expense. i do not believe this is a safety improvement over not having the sensors which are now required by law. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 70100 miles. Vehicle Identification Number (VIN):JM1BL1H53A1. Mazda Mazda3 2010 problem was reported in OAK RIDGE, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10566252

MAZDA MAZDA3 2010 car safety problem was reported on Feb 20, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with WHEELS . rear tire was flat in the morning. could not find visible damage. pumped it up to 32 psi and by next morning it was 20 psi. three days later, a front tire was flat. no noticeable damage, but did notice a cracked tire stem on a third tire. went to a tire dealer to get repairs. was informed that three of my four tire pressure monitor sensors were leaking. had all four replaced at my expense. i do not believe this is a safety improvement over not having the sensors which are now required by law. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 70100 miles. Vehicle Identification Number (VIN):JM1BL1H53A1. Mazda Mazda3 2010 problem was reported in OAK RIDGE, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10567770

MAZDA MAZDA3 2010 car safety problem was reported on Jan 22, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with TIRES . tire pressure gauge broke off, resulting in sudden loss of tire pressure and the need to suddenly slow and pull over. after taking it into be serviced, the mazda dealer says all four are corroded, and need to be replaced. at 4 years and less than 40,000 miles, this seems clearly like a potential safety problem with the car in general. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 38000 miles. Vehicle Identification Number (VIN):JM1BL1SF1A1. Mazda Mazda3 2010 problem was reported in MADISON, WI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10567770

MAZDA MAZDA3 2010 car safety problem was reported on Jan 22, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with WHEELS . tire pressure gauge broke off, resulting in sudden loss of tire pressure and the need to suddenly slow and pull over. after taking it into be serviced, the mazda dealer says all four are corroded, and need to be replaced. at 4 years and less than 40,000 miles, this seems clearly like a potential safety problem with the car in general. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 38000 miles. Vehicle Identification Number (VIN):JM1BL1SF1A1. Mazda Mazda3 2010 problem was reported in MADISON, WI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 35 mph.

Mazda Mazda3 2010 Tires

Mazda Mazda3 2010 Tires Review #10568920

MAZDA MAZDA3 2010 car safety problem was reported on Sept 19, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with TIRES . it is now march 2014, and 3 of the tpms valve stems have corroded and are falling apart. the first one was discovered during tire replacement. now 2 more are falling apart. all components are the original, so the claim about galvanic corrosion due to using aftermarket valves with brass is irrelevant. mazda has a serious safety problem and is doing nothing about it. for reference i also own a toyota rav4 and the tpms are still perfect. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 103000 miles. Mazda Mazda3 2010 problem was reported in ST HELENA ISLAND, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Exterior Lighting

Mazda Mazda3 2010 Exterior Lighting Review #10573945

MAZDA MAZDA3 2010 car safety problem was reported on Mar 17, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with EXTERIOR LIGHTING . condensation forms in headlight housing causing hid module to short circuit and headlight to fail. safety concern regarding visibility could lead to accident. manufacturer refuses to take blame for faulty construction leading to malfunction resulting in consumer having to pay full cost of headlight assembly and new hid module. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 49000 miles. Vehicle Identification Number (VIN):JM1BL1S61A1. Mazda Mazda3 2010 problem was reported in CLAYMONT, DE. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda3 2010 Electrical System

Mazda Mazda3 2010 Electrical System Review #10573945

MAZDA MAZDA3 2010 car safety problem was reported on Mar 17, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with ELECTRICAL SYSTEM . condensation forms in headlight housing causing hid module to short circuit and headlight to fail. safety concern regarding visibility could lead to accident. manufacturer refuses to take blame for faulty construction leading to malfunction resulting in consumer having to pay full cost of headlight assembly and new hid module. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 49000 miles. Vehicle Identification Number (VIN):JM1BL1S61A1. Mazda Mazda3 2010 problem was reported in CLAYMONT, DE. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10574034

MAZDA MAZDA3 2010 car safety problem was reported on Jan 01, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . tl* the contact owns a 2010 mazda3. the contact stated that the driver's seat frame separated from the base. the contact's independent mechanic inspected the vehicle and found a defective welding, which caused the base to separate from the seat. the manufacturer was made aware of the failure. the vehicle was not repaired. the vin was not available. the failure mileage was 60,000 and the current the vehicle was 100,000. .0 person(s) were injured. 0 person(s) died.Mileage was 60000 miles. Mazda Mazda3 2010 problem was reported in CHESTERFIELD, MI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Seats Review #10578322

MAZDA MAZDA3 2010 car safety problem was reported on Apr 18, 2013.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with SEATS . tl* the contact owns a 2010 mazda mazda3. the contact stated that the driver's seat frame became separated from the base. the vehicle was taken to a dealer where the technician diagnosed that the seat bracket had fractured and needed to be replaced. the vehicle was not repaired. the manufacturer was made aware of the failure. the failure mileage was 60,000 and the current the vehicle was 86,000. .0 person(s) were injured. 0 person(s) died.Mileage was 60000 miles. Vehicle Identification Number (VIN):JM1BL1H48A1. Mazda Mazda3 2010 problem was reported in LEXINGTON, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Structure Body

Mazda Mazda3 2010 Structure Body Review #10578977

MAZDA MAZDA3 2010 car safety problem was reported on Oct 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE:BODY . the whole dashboard is melting. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 29000 miles. Vehicle Identification Number (VIN):JM1BL1SF3A1. Mazda Mazda3 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10583509

MAZDA MAZDA3 2010 car safety problem was reported on Apr 07, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with SEATS . driver seat is loose and rocks. a piece of metal detached and it looks like very cheap metal and poor welding. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 59888 miles. Mazda Mazda3 2010 problem was reported in MERRICK, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10585520

MAZDA MAZDA3 2010 car safety problem was reported on Apr 29, 2014.MAZDA MAZDA3 2010, manufactured by MAZDA MOTOR CORP had a problem with WHEELS . tl* the contact owns a 2010 mazda 3. the contact stated while driving various speeds, the tpms light illuminated. the contact stated that the failure was experienced multiple times. the vehicle was not diagnosed or repaired. the manufacturer was notified. the failure mileage was 51,850..0 person(s) were injured. 0 person(s) died.Mileage was 51850 miles. Vehicle Identification Number (VIN):JM1BL1SG3A1. Mazda Mazda3 2010 problem was reported in READING, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Structure

Mazda Mazda3 2010 Structure Review #10586044

MAZDA MAZDA3 2010 car safety problem was reported on July 16, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE . car was purchased in 2009 and up until last year i had very few problems and was very happy with the car. however, last year i noticed my dashboard appeared to be very shiny and extremely sticky. it appeared as though some type of glue had been poured on it. when i touched the dashboard the melted material would come off on my fingers. i took it to the dealership who said they had never seen anything like it. they arranged to have the mazda area representative come and look at it. he examined the dashboard and told me he has seen this before, mostly in states like florida, that are basically hot all year. he stated it was the glue used to secure the dashboard which was leaching up. he approved the dealership to replace the part at no charge, however the dealership said it would cost $300.00 to have it installed. if the part was faulty why do i need to pay to have the new part installed. i have done nothing and continue to have a defective dashboard, my concern is will the airbag work correctly inside this defective dashboard? i have recently seen the investigative report on my local news concerning this issue. without question this is a safety issue in my opinion. *tr.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1H58A1. Mazda Mazda3 2010 problem was reported in BOCA RATON, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda3 2010 Engine

Mazda Mazda3 2010 Engine Review #10587446

MAZDA MAZDA3 2010 car safety problem was reported on Nov 15, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with ENGINE . clutch gave out at 33,000 miles. that is absurd. mazda claims its under their "wear and tear" but this is not a new problem for a lot of people. premature clutch failure should have been a recall on mazda 3's back in 2011. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 33000 miles. Mazda Mazda3 2010 problem was reported in WINDHAM, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Power Train

Mazda Mazda3 2010 Power Train Review #10587446

MAZDA MAZDA3 2010 car safety problem was reported on Nov 15, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with POWER TRAIN . clutch gave out at 33,000 miles. that is absurd. mazda claims its under their "wear and tear" but this is not a new problem for a lot of people. premature clutch failure should have been a recall on mazda 3's back in 2011. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 33000 miles. Mazda Mazda3 2010 problem was reported in WINDHAM, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Power Train Review #10588018

MAZDA MAZDA3 2010 car safety problem was reported on May 11, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with POWER TRAIN . i was driving down the road all the sudden my car stopped and would not engage. apparently my clutch just randomly went out. i have to completely replace the entire thing $1000. mazda said its a normal wear and tear at 67000 miles we should not be doing a complete replacement of the clutch. it should not just randomly go out without any warning. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 67000 miles. Vehicle Identification Number (VIN):JM1BL1SF3A1. Mazda Mazda3 2010 problem was reported in HUTCHINSON, KS. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Mazda Mazda3 2010 Structure

Mazda Mazda3 2010 Structure Review #10592449

MAZDA MAZDA3 2010 car safety problem was reported on Feb 03, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE . dashboard is very shiny. started to reflect of windshield and cause a glare. very sticky and is literally melting. has a constant shine can no longer clean it and glare is getting worse and dangerous at this point. *js.0 person(s) were injured. 0 person(s) died.Mileage was 52000 miles. Vehicle Identification Number (VIN):JM1BL1SF5A1. Mazda Mazda3 2010 problem was reported in BOYNTON BEACH, FM. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD.

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems Review #10592677

MAZDA MAZDA3 2010 car safety problem was reported on May 18, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS . in the mazda 3, the tpms sensor is connected to the air valve. the tpms sensors break easily, causing the tire to deflate. if the outside part of the tpms sensor breaks from corrosion or being hit against a curb, the tire will deflate. i have had 3 tpms sensors break since i had the car, which has only been 4 years (approx 39,000 miles), and is expensive to replace. my tires are less than 3 years old. the part of the tpms exposed on the outside will corrode, and if the outside part breaks off, your tires deflate. this is a common problem for mazda owners. these things break and then cause a flat, leaving the driver in a possible emergency situation. the reason for the tpms sensor is so drivers don't have blow outs, but the emergency light is very nonspecific, so the only way you know what the problem is when the flat has already occurred, which is unnecessarily caused by the tpms sensor. this latest incident involved me stranded in the country, yet another tpms sensor replacement ($200 approx), a new tire, and an alignment - almost $500 total. if the tpms sensor hadn't broken, the flat would not have occurred at all. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 39078 miles. Vehicle Identification Number (VIN):JM1BL1S59A1. Mazda Mazda3 2010 problem was reported in CHICAGO, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 55 mph.

Mazda Mazda3 2010 Equipment Adaptive

Mazda Mazda3 2010 Equipment Adaptive Review #10592677

MAZDA MAZDA3 2010 car safety problem was reported on May 18, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with EQUIPMENT ADAPTIVE . in the mazda 3, the tpms sensor is connected to the air valve. the tpms sensors break easily, causing the tire to deflate. if the outside part of the tpms sensor breaks from corrosion or being hit against a curb, the tire will deflate. i have had 3 tpms sensors break since i had the car, which has only been 4 years (approx 39,000 miles), and is expensive to replace. my tires are less than 3 years old. the part of the tpms exposed on the outside will corrode, and if the outside part breaks off, your tires deflate. this is a common problem for mazda owners. these things break and then cause a flat, leaving the driver in a possible emergency situation. the reason for the tpms sensor is so drivers don't have blow outs, but the emergency light is very nonspecific, so the only way you know what the problem is when the flat has already occurred, which is unnecessarily caused by the tpms sensor. this latest incident involved me stranded in the country, yet another tpms sensor replacement ($200 approx), a new tire, and an alignment - almost $500 total. if the tpms sensor hadn't broken, the flat would not have occurred at all. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 39078 miles. Vehicle Identification Number (VIN):JM1BL1S59A1. Mazda Mazda3 2010 problem was reported in CHICAGO, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 55 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10592677

MAZDA MAZDA3 2010 car safety problem was reported on May 18, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with WHEELS . in the mazda 3, the tpms sensor is connected to the air valve. the tpms sensors break easily, causing the tire to deflate. if the outside part of the tpms sensor breaks from corrosion or being hit against a curb, the tire will deflate. i have had 3 tpms sensors break since i had the car, which has only been 4 years (approx 39,000 miles), and is expensive to replace. my tires are less than 3 years old. the part of the tpms exposed on the outside will corrode, and if the outside part breaks off, your tires deflate. this is a common problem for mazda owners. these things break and then cause a flat, leaving the driver in a possible emergency situation. the reason for the tpms sensor is so drivers don't have blow outs, but the emergency light is very nonspecific, so the only way you know what the problem is when the flat has already occurred, which is unnecessarily caused by the tpms sensor. this latest incident involved me stranded in the country, yet another tpms sensor replacement ($200 approx), a new tire, and an alignment - almost $500 total. if the tpms sensor hadn't broken, the flat would not have occurred at all. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 39078 miles. Vehicle Identification Number (VIN):JM1BL1S59A1. Mazda Mazda3 2010 problem was reported in CHICAGO, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 55 mph.

Mazda Mazda3 2010 Steering Electric Power Assist System

Mazda Mazda3 2010 Steering Electric Power Assist System Review #10594497

MAZDA MAZDA3 2010 car safety problem was reported on May 13, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STEERING:ELECTRIC POWER ASSIST SYSTEM . tl* the contact owns a 2010 mazda mazda3. the contact stated that while driving 45 mph, the power steering warning light illuminated as the power steering assist failed. the vehicle was taken to a dealer where it was diagnosed that the power steering assist module needed to be replaced. the vehicle was repaired. the manufacturer was made aware of the failure. the failure mileage and current mileage was 90,000. the vin was not available. dr.0 person(s) were injured. 0 person(s) died.Mileage was 90000 miles. Mazda Mazda3 2010 problem was reported in FORTH WORTH, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Mazda Mazda3 2010 Steering Review #10594497

MAZDA MAZDA3 2010 car safety problem was reported on May 13, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STEERING . tl* the contact owns a 2010 mazda mazda3. the contact stated that while driving 45 mph, the power steering warning light illuminated as the power steering assist failed. the vehicle was taken to a dealer where it was diagnosed that the power steering assist module needed to be replaced. the vehicle was repaired. the manufacturer was made aware of the failure. the failure mileage and current mileage was 90,000. the vin was not available. dr.0 person(s) were injured. 0 person(s) died.Mileage was 90000 miles. Mazda Mazda3 2010 problem was reported in FORTH WORTH, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems Review #10594550

MAZDA MAZDA3 2010 car safety problem was reported on May 22, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS . while driving on the highway my tire pressure monitor system (tpms) light came on to indicate a low tire. i pulled into the gas station near my house right after and check my tire pressures. when checking the driver side rear tire pressure with a tire pressure gauge the tpms sensor and stem pushed in and air blasted out, blowing several pieces of the sleeve that keeps the stem in place off of the wheel/stem. i picked up the 2 remaining pieces (one third of the sleeve was missing and presumed to have fallen off while driving) and they had cracked length-wise and had a large amount of white corrosion in the threads. the remaining stem was also covered in white corrosion on the threads and the tire had lost most of its pressure. i still have those pieces of the cracked tpms sensor sleeve if needed to be examined. i took the vehicle and wheel to the mazda dealership where they inspected that wheel as well as the others. they stated that 2 of my other tpms sensors had cracked sleeves that could come off at any time in addition the one that had failed. if one of those had failed on one of my front wheels this could have caused a loss of control while driving. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 59025 miles. Vehicle Identification Number (VIN):JM1BL1SF5A1. Mazda Mazda3 2010 problem was reported in CRESCENT SPRINGS, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10594550

MAZDA MAZDA3 2010 car safety problem was reported on May 22, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with WHEELS . while driving on the highway my tire pressure monitor system (tpms) light came on to indicate a low tire. i pulled into the gas station near my house right after and check my tire pressures. when checking the driver side rear tire pressure with a tire pressure gauge the tpms sensor and stem pushed in and air blasted out, blowing several pieces of the sleeve that keeps the stem in place off of the wheel/stem. i picked up the 2 remaining pieces (one third of the sleeve was missing and presumed to have fallen off while driving) and they had cracked length-wise and had a large amount of white corrosion in the threads. the remaining stem was also covered in white corrosion on the threads and the tire had lost most of its pressure. i still have those pieces of the cracked tpms sensor sleeve if needed to be examined. i took the vehicle and wheel to the mazda dealership where they inspected that wheel as well as the others. they stated that 2 of my other tpms sensors had cracked sleeves that could come off at any time in addition the one that had failed. if one of those had failed on one of my front wheels this could have caused a loss of control while driving. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 59025 miles. Vehicle Identification Number (VIN):JM1BL1SF5A1. Mazda Mazda3 2010 problem was reported in CRESCENT SPRINGS, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 60 mph.

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems

Mazda Mazda3 2010 Tires Pressure Monitoring And Regulating Systems Review #10596342

MAZDA MAZDA3 2010 car safety problem was reported on Apr 19, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS . on 4/19/14, i had a broken tpms sensor which needed to be replaced. this sensor was on the passenger side, front tire. then again on 6/2/14, i had the same problem on a different tire - the driver side back tire. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 53000 miles. Mazda Mazda3 2010 problem was reported in WILLIAMSVILLE, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10596342

MAZDA MAZDA3 2010 car safety problem was reported on Apr 19, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with WHEELS . on 4/19/14, i had a broken tpms sensor which needed to be replaced. this sensor was on the passenger side, front tire. then again on 6/2/14, i had the same problem on a different tire - the driver side back tire. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 53000 miles. Mazda Mazda3 2010 problem was reported in WILLIAMSVILLE, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Service Brakes

Mazda Mazda3 2010 Service Brakes Review #10596685

MAZDA MAZDA3 2010 car safety problem was reported on June 03, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with SERVICE BRAKES . tl* the contact owns a 2010 mazda mazda3. the contact stated that while driving 45 mph, the vehicle failed to respond to deceleration attempts. the vehicle was not diagnosed or repaired. the manufacturer was made aware of the failure. the failure and current mileage was 60,000..Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Mileage was 60000 miles. Vehicle Identification Number (VIN):JM1BL1SG7A1. Mazda Mazda3 2010 problem was reported in IRVIN, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10596768

MAZDA MAZDA3 2010 car safety problem was reported on June 02, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with SEATS . while driving herd a popping under the drivers seat, the seat then started rocking back in forth. seat is unsafe to drive. noticed several other complaints about the exact same thing obviously there is a problem with the weld points on this model. my 3rd mazda never had any problems with my 1st 2 but the 2010 mazda 3 quality does not hold up to the previous years. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 72000 miles. Mazda Mazda3 2010 problem was reported in FLORENCE, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 15 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10598255

MAZDA MAZDA3 2010 car safety problem was reported on Mar 20, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . approximately 2 years ago i noticed my dash board was wet looking and sticky. it has progressively gotten worse. my dash board is melting. this is a huge saftey hazzard as the glare from the melting dash affects my vision when driving during the daylight. *js.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF5A1. Mazda Mazda3 2010 problem was reported in LAKE CITY, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD.

Mazda Mazda3 2010 Structure Body

Mazda Mazda3 2010 Structure Body Review #10598255

MAZDA MAZDA3 2010 car safety problem was reported on Mar 20, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE:BODY . approximately 2 years ago i noticed my dash board was wet looking and sticky. it has progressively gotten worse. my dash board is melting. this is a huge saftey hazzard as the glare from the melting dash affects my vision when driving during the daylight. *js.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF5A1. Mazda Mazda3 2010 problem was reported in LAKE CITY, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD.

Mazda Mazda3 2010 Structure Review #10598734

MAZDA MAZDA3 2010 car safety problem was reported on July 11, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE . melting dashboard - causes awful glare in window at times of day. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 60000 miles. Mazda Mazda3 2010 problem was reported in PALMETTO, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10598734

MAZDA MAZDA3 2010 car safety problem was reported on July 11, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . melting dashboard - causes awful glare in window at times of day. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 60000 miles. Mazda Mazda3 2010 problem was reported in PALMETTO, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Structure

Mazda Mazda3 2010 Structure Review #10598981

MAZDA MAZDA3 2010 car safety problem was reported on June 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE . within the last year, the heat from the sun has melted the dashboard. it becomes sticky and flaking off. the major issue is the glare it causes on the windshield when driving. *tr.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1S50A1. Mazda Mazda3 2010 problem was reported in BROOKSVILLE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10604895

MAZDA MAZDA3 2010 car safety problem was reported on June 02, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . dashboard melting which causes glare while driving. *tr.0 person(s) were injured. 0 person(s) died.Mazda Mazda3 2010 problem was reported in ORLANDO, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Structure

Mazda Mazda3 2010 Structure Review #10604895

MAZDA MAZDA3 2010 car safety problem was reported on June 02, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE . dashboard melting which causes glare while driving. *tr.0 person(s) were injured. 0 person(s) died.Mazda Mazda3 2010 problem was reported in ORLANDO, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Air Bags

Mazda Mazda3 2010 Air Bags Review #10605484

MAZDA MAZDA3 2010 car safety problem was reported on Jan 06, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with AIR BAGS . in last 6 months my dashboard is melting! i have noticed it was getting shiny and sticky as if someone had poured glue on it. i have tried to use numerous different cleaners and nothing happens. the surface is so shiny it is causing glare when i drive or mt teenagers drive the car. this is unsafe. now i am researching and find numerous complaints about same issue. is this also affecting my airbag? *tr.0 person(s) were injured. 0 person(s) died.Mileage was 80000 miles. Vehicle Identification Number (VIN):JM1BL1SF7A1. Mazda Mazda3 2010 problem was reported in TAMPA, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Structure Body

Mazda Mazda3 2010 Structure Body Review #10605484

MAZDA MAZDA3 2010 car safety problem was reported on Jan 06, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE:BODY . in last 6 months my dashboard is melting! i have noticed it was getting shiny and sticky as if someone had poured glue on it. i have tried to use numerous different cleaners and nothing happens. the surface is so shiny it is causing glare when i drive or mt teenagers drive the car. this is unsafe. now i am researching and find numerous complaints about same issue. is this also affecting my airbag? *tr.0 person(s) were injured. 0 person(s) died.Mileage was 80000 miles. Vehicle Identification Number (VIN):JM1BL1SF7A1. Mazda Mazda3 2010 problem was reported in TAMPA, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Visibility Sun Roof Assembly

Mazda Mazda3 2010 Visibility Sun Roof Assembly Review #10606416

MAZDA MAZDA3 2010 car safety problem was reported on June 26, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY:SUN ROOF ASSEMBLY . while driving on a highway at approximately 65-70 mph, i heard like a gunshot and at first thought there was a terrible accident behind me. however, i immediately realized that there was a gaping hole in my sunroof. at the time, the temperature was approximately 92 degrees and the sunroof was closed. the inside cover, however, was open, so there was glass everywhere inside my car. i was traveling uphill at the time and there was no indication of any debris or rocks. my front windshield and the body of my car was fine. it was just the sunroof that seemed to explode on its own. mazda would not take responsibility for this incident. an insurance claim has been filed. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 80000 miles. Vehicle Identification Number (VIN):VIN: JM1BL1. Mazda Mazda3 2010 problem was reported in SANTA FE, NM. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 65 mph.

Mazda Mazda3 2010 Structure

Mazda Mazda3 2010 Structure Review #10606684

MAZDA MAZDA3 2010 car safety problem was reported on June 28, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE . the dashboard in my 2010 mazda 3 is melting making it look as if a sticky substance is covering it. on touch, fingers stick to the dashboard. the car remains in a covered parking garage at all times, so it is not being exposed to extreme heat conditions. the only exposure to the sun is while driving and during that time, the car's air conditioning is on. the sticky substance causes a glare on the windshield, which in florida is a major safety concern. it seems a very cheap and defective material has been used in the manufacturing of the dashboard. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 41129 miles. Vehicle Identification Number (VIN):JM1BL1SF8A1. Mazda Mazda3 2010 problem was reported in TAMPA, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10607644

MAZDA MAZDA3 2010 car safety problem was reported on Nov 01, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . dashboard started melting, to my surprise when i contacted the dealer they said that was probably by a cleaning product witch wasn't the case. this is very distracting when driving during the day and night by the glare, makes it very difficult. it seems it is the case to many others mazda 3 owners i know. i never saw this happening to any car dashboard before. it concerns me because of my safety when driving. .0 person(s) were injured. 0 person(s) died.Mazda Mazda3 2010 problem was reported in MERCEDITA, PR. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10608472

MAZDA MAZDA3 2010 car safety problem was reported on July 06, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with WHEELS . low tire pressure light came on while driving. pulled in to the gas station to check tires and noticed a flat rear tire. went to put air in and saw the valve stem was gone. had it towed and was told i need to replace all of them. they are all cracked. just got back from a vacation. glad this didnt happen on the tunpike. seems very soon for this to happen. been driving 40 years. this is a first.very expensive and dangerous.40 ,000 miles seems pretty soon for this..0 person(s) were injured. 0 person(s) died.Mileage was 41000 miles. Mazda Mazda3 2010 problem was reported in PITTSBURGH, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10609465

MAZDA MAZDA3 2010 car safety problem was reported on June 02, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . dashboard of my mazda 3 2010 is sticky and melting causing a glare on my windshield. this is very unsafe as i drive during high traffic times.0 person(s) were injured. 0 person(s) died.Mileage was 42000 miles. Mazda Mazda3 2010 problem was reported in SAN ANTONIO, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility Sun Roof Assembly

Mazda Mazda3 2010 Visibility Sun Roof Assembly Review #10609665

MAZDA MAZDA3 2010 car safety problem was reported on July 08, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY:SUN ROOF ASSEMBLY . tl* the contact owns a 2010 mazda3. the contact stated that while driving approximately 45 mph, the sun roof suddenly shattered. the contacted indicated that the sun roof was in the closed position during the incident. the vehicle was taken to the dealer. the manufacturer was notified. no assistance was offered. the failure mileage was 67,000...updated 08-26-14 *bf the consumer stated after researching the matter it found that sunroof explosions are a documented occurrence due to low tempered glass, primarily from mexico. updated 09/2/2014 *js updated 8/20/14*cn.0 person(s) were injured. 0 person(s) died.Mileage was 67000 miles. Vehicle Identification Number (VIN):JM1BL1S67A1. Mazda Mazda3 2010 problem was reported in JACKSON, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. VEHICLE SPEED: 45 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10610700

MAZDA MAZDA3 2010 car safety problem was reported on July 15, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dash cover in the car is melting and the glare from the melted dash is causing problems with visibility..0 person(s) were injured. 0 person(s) died.Mazda Mazda3 2010 problem was reported in WEST MELBOURNE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10614475

MAZDA MAZDA3 2010 car safety problem was reported on July 12, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with SEATS . the driver seat began to wobble back and forth while driving the car. the problem is due to a sheet metal piece (approximately 1/8 inch thick) that holds the seat bottom to the seat slide adjustment. the spring retainer had popped off the locating pin allowing the sheet metal to bend and the pin to come out of its retaining hole. i attempted to replace the spring retainer, but the sheet metal snapped due to work hardening. the failure mechanism appears to occur because the sheet metal is stamped during manufacture and a hole approximately 1/2 the width of the sheet metal is punched through the the sheet metal drastically reducing its strength. i purchased a new slide mechanism because mazda does not have a recall or special service program for this failure. however, when i examined the new slide mechanism, i discovered that mazda has significantly redesigned this part to prevent the type of failure that i experienced. the new piece does not have the punched hole, but instead has a reinforced boss as well as significant amounts of welding to ensure the piece cannot bend or break. my guess is that the new design is at least 100 times more durable than the original design. obviously, mazda considered the old design to be substandard. i believe that this should be the subject of a recall to verify that the seat retention has not failed. this is a safety issue because the failure results in only 3 points of retention for the seat and the driver can possibly lose control due to improper restraint in the seat. i can supply pictures of the new design and defective design if you need them. there are two such pieces per seat so the possibility exists for both to fail in sequence creating a more serious safety issue..0 person(s) were injured. 0 person(s) died.Mileage was 65595 miles. Vehicle Identification Number (VIN):JM1BL1SFXA1. Mazda Mazda3 2010 problem was reported in AUSTIN, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10614623

MAZDA MAZDA3 2010 car safety problem was reported on Dec 17, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dashboard seems to be melting by the front windshield. this is producing a glare on the windshield which is seen while driving..0 person(s) were injured. 0 person(s) died.Mazda Mazda3 2010 problem was reported in SUNRISE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10615052

MAZDA MAZDA3 2010 car safety problem was reported on June 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dashboard on my mazda 3, 2010 is melting. it is soft and sticky.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF8A1. Mazda Mazda3 2010 problem was reported in BIRMINGHAM, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10615196

MAZDA MAZDA3 2010 car safety problem was reported on Dec 04, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . i have had my vehicle for almost 4 yrs.the dashboard started to melt in 2013. it creates a shinny reflection on the front glass which becomes very irritating unable to see clearly..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1H57A. Mazda Mazda3 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10615196

MAZDA MAZDA3 2010 car safety problem was reported on Dec 04, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . i have had my vehicle for almost 4 yrs.the dashboard started to melt in 2013. it creates a shinny reflection on the front glass which becomes very irritating unable to see clearly..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1H57A. Mazda Mazda3 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10615560

MAZDA MAZDA3 2010 car safety problem was reported on May 16, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dashboard on my car has begun to melt, creating a very shiny slick which (when driving at the proper angle) causes the sun to reflect into my eyes. while i have had the car for about 5 years, it has only begun to melt this summer..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1S58A1. Mazda Mazda3 2010 problem was reported in ORLANDO, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10616106

MAZDA MAZDA3 2010 car safety problem was reported on Mar 03, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . i own a 2010 mazda 3. within the last year, the dash has started to melt. i've contacted mazda and because it's out of warranty, they were unable to help in anyway. the car is only 4 years old! .0 person(s) were injured. 0 person(s) died.Mazda Mazda3 2010 problem was reported in PALM BEACH GARDENS, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10616363

MAZDA MAZDA3 2010 car safety problem was reported on June 02, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dashboard of my 2010 mazda3 is melting. i noticed this about a month ago, but whether it started before that i'm not sure. now there is a glossy sheen to the dashboard that impairs my vision when driving in the morning or the evening, when the sun is rising or setting. it creates a glare on the glass..0 person(s) were injured. 0 person(s) died.Mileage was 45000 miles. Mazda Mazda3 2010 problem was reported in WEST PALM BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10617129

MAZDA MAZDA3 2010 car safety problem was reported on June 07, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . top front dashboard is melting. the material is now sticky and can't be cleaned because the rag/towel sticks. when touched black residue sticks to your hands and when driving the sun reflects off the shiny stickiness and causes a driving hazard on the windshield. .0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1S58A1. Mazda Mazda3 2010 problem was reported in TAMARAC, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10617129

MAZDA MAZDA3 2010 car safety problem was reported on June 07, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . top front dashboard is melting. the material is now sticky and can't be cleaned because the rag/towel sticks. when touched black residue sticks to your hands and when driving the sun reflects off the shiny stickiness and causes a driving hazard on the windshield. .0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1S58A1. Mazda Mazda3 2010 problem was reported in TAMARAC, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10617306

MAZDA MAZDA3 2010 car safety problem was reported on Mar 03, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dashboard in my mazda 3 is "melting". the dashboard is sticky, tacky to the touch and deforming. the car is 4.5 years old and the dealership will not cover the issue under the extended warranty, my factory warranty expired last year. this is clearly a manufacturing defect.the dashboard has become shiny in the affected area due to the "melting" and is reflecting the sunlight into my eyes during driving in sunny weather and is becoming a safety issue. .0 person(s) were injured. 0 person(s) died.Mileage was 33000 miles. Vehicle Identification Number (VIN):JM1BL1SF4A1. Mazda Mazda3 2010 problem was reported in COOPER CITY, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other Review #10617479

MAZDA MAZDA3 2010 car safety problem was reported on June 30, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dashboard on my 2010 mazda3 hatchback is melting and sticky. while driving towards the sun, the glare from the shiny sticky area reflects onto the windshield and makes it very difficult to see out. in fact, i didn't even notice the sticky melting dash at first, what i noticed first was the fact that i was having difficulty seeing out of the windshield. i take very good care of my car. i have not used a bunch of cleaners on the dash in the past. i do use a sun shade in the windshield when parked..0 person(s) were injured. 0 person(s) died.Mileage was 30000 miles. Mazda Mazda3 2010 problem was reported in GULF SHORES, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10617479

MAZDA MAZDA3 2010 car safety problem was reported on June 30, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . the dashboard on my 2010 mazda3 hatchback is melting and sticky. while driving towards the sun, the glare from the shiny sticky area reflects onto the windshield and makes it very difficult to see out. in fact, i didn't even notice the sticky melting dash at first, what i noticed first was the fact that i was having difficulty seeing out of the windshield. i take very good care of my car. i have not used a bunch of cleaners on the dash in the past. i do use a sun shade in the windshield when parked..0 person(s) were injured. 0 person(s) died.Mileage was 30000 miles. Mazda Mazda3 2010 problem was reported in GULF SHORES, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper Review #10617899

MAZDA MAZDA3 2010 car safety problem was reported on Apr 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . this car mazda 3 i purchased in 2011 as a 2010 leftover new, and the dash board is melting creating everything to stick to it, and also obstructing my view through the windshield on sunny days due to the nature of how shinny it is. it looks like a wet down dash but the reflection is creating very difficult viewing problems on sunny days, due to the glare on the windshield from it. it is very dangerous. i would appreciate this being looked into..0 person(s) were injured. 0 person(s) died.Mileage was 11000 miles. Vehicle Identification Number (VIN):JM1BL1S53A1. Mazda Mazda3 2010 problem was reported in WIMAUMA, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10617899

MAZDA MAZDA3 2010 car safety problem was reported on Apr 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . this car mazda 3 i purchased in 2011 as a 2010 leftover new, and the dash board is melting creating everything to stick to it, and also obstructing my view through the windshield on sunny days due to the nature of how shinny it is. it looks like a wet down dash but the reflection is creating very difficult viewing problems on sunny days, due to the glare on the windshield from it. it is very dangerous. i would appreciate this being looked into..0 person(s) were injured. 0 person(s) died.Mileage was 11000 miles. Vehicle Identification Number (VIN):JM1BL1S53A1. Mazda Mazda3 2010 problem was reported in WIMAUMA, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10618802

MAZDA MAZDA3 2010 car safety problem was reported on July 27, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . 2010 mazda 3 dash panel/dashboard (p/n: bbm460400h02) is melting. the dash panel soft-touch coating material first turned sticky and eventually disintegrated into a viscous substance. surface finish turned from matte to high gloss. the now reflective dash surface causes a large glare on the windshield and obstructs driver⿿s visibility. .0 person(s) were injured. 0 person(s) died.Mileage was 44000 miles. Vehicle Identification Number (VIN):JM1BL1S58A1. Mazda Mazda3 2010 problem was reported in DANIA BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10618802

MAZDA MAZDA3 2010 car safety problem was reported on July 27, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . 2010 mazda 3 dash panel/dashboard (p/n: bbm460400h02) is melting. the dash panel soft-touch coating material first turned sticky and eventually disintegrated into a viscous substance. surface finish turned from matte to high gloss. the now reflective dash surface causes a large glare on the windshield and obstructs driver⿿s visibility. .0 person(s) were injured. 0 person(s) died.Mileage was 44000 miles. Vehicle Identification Number (VIN):JM1BL1S58A1. Mazda Mazda3 2010 problem was reported in DANIA BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10619177

MAZDA MAZDA3 2010 car safety problem was reported on June 04, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . dashboard melted due to sun exposure - dashboard had to replaced due to glare on windshield..0 person(s) were injured. 0 person(s) died.Mileage was 32000 miles. Vehicle Identification Number (VIN):JM1BL1SF9A1. Mazda Mazda3 2010 problem was reported in HOUSTON, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10620980

MAZDA MAZDA3 2010 car safety problem was reported on Aug 08, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with WHEELS . all four wheels are rusting. rust is so bad that a flat tire cannot be changed, the wheels are rusted completely to the axles. car has never been exposed to salt water and was purchased new.0 person(s) were injured. 0 person(s) died.Mileage was 97000 miles. Vehicle Identification Number (VIN):JM1BL1SGXA1. Mazda Mazda3 2010 problem was reported in NORTH BERGEN, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10621812

MAZDA MAZDA3 2010 car safety problem was reported on Aug 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . vehicle was purchased new. the dashboard is melting. it is sticky to the touch and shiny. the shiny areas reflect sunlight and cause difficulty seeing out of the windshield. this should be replaced by the manufacturer as it is an obvious material defect!.0 person(s) were injured. 0 person(s) died.Mileage was 38000 miles. Vehicle Identification Number (VIN):JM1BL1SF9A1. Mazda Mazda3 2010 problem was reported in KEY WEST, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10621852

MAZDA MAZDA3 2010 car safety problem was reported on Dec 04, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with WHEELS . the tire pressure sensors became corroded. one broke off during getting new tires installed, the second happened while i was filling the tire with air. it just fell apart in my hand..0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Mazda Mazda3 2010 problem was reported in KANSAS CITY, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10622050

MAZDA MAZDA3 2010 car safety problem was reported on July 12, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . dashboard getting very soft in the sun. always remains sticky and continues to leave residue on the windshield causing glare..0 person(s) were injured. 0 person(s) died.Mileage was 20000 miles. Vehicle Identification Number (VIN):JM1BL1S56A1. Mazda Mazda3 2010 problem was reported in LARGO, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10622050

MAZDA MAZDA3 2010 car safety problem was reported on July 12, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . dashboard getting very soft in the sun. always remains sticky and continues to leave residue on the windshield causing glare..0 person(s) were injured. 0 person(s) died.Mileage was 20000 miles. Vehicle Identification Number (VIN):JM1BL1S56A1. Mazda Mazda3 2010 problem was reported in LARGO, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10622146

MAZDA MAZDA3 2010 car safety problem was reported on May 01, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . dash board is melting. when driving it causes a glare on windshield which is dangerous when driving!.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF8A1. Mazda Mazda3 2010 problem was reported in LAKELAND, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10622296

MAZDA MAZDA3 2010 car safety problem was reported on Feb 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . i'm writing this complaint to officially detail, in writing, that mazda has refused to acknowledge the fact that the dashboard on my 2010 mazda3 has melted! i brought this issue to their attention this past april, 2014, when i had my car at my local shop for other repair issues. my advisor called later that afternoon to say that his manager stated that because my car was "out of warranty", it was my responsibility to replace the dashboard at a cost of approximately $1000 out of pocket! they were not accommodating at all. this is completely ludicrous! cars should not melt! my dashboard is totally ruined! i can never again even wipe it off as it has literally turned into the consistency of flypaper! the melted, sticky, mess gets on/ruins everything it touches! and, this isn't even the worst part! the glare that radiates off of my windshield at certain times of the day is horrific! driving is a total safety hazard!! i am afraid to drive my car! it's so dangerous! i have pictures i can send if you would like to see them! i find this to be completely unacceptable! warranty or not, this is a blatant defect in the manufacturing of this car! my local news channel has done an investigation on this issue and the last i heard, lawyers are getting involved and they had mentioned a class action lawsuit against mazda, lexus, and nissan. something needs to be done. this is not a rare incident! this is a huge, prevalent problem! not to mention, the value of my car is now in the toilet! if i went to trade it in or sell it, even though it only has 59,000 miles, i would take a huge hit on what i would get for it! this is a defect! mazda needs to be held accountable and they need to be forced to replace all of these defects (using new, updated dashboard material so it doesn't happen again), at no cost to the consumer, before someone gets killed because of the glare issue caused by this! .0 person(s) were injured. 0 person(s) died.Mileage was 50000 miles. Vehicle Identification Number (VIN):JM1BL1SF8A1. Mazda Mazda3 2010 problem was reported in PALM SPRINGS, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10625788

MAZDA MAZDA3 2010 car safety problem was reported on Aug 14, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . dashboard is melting, sticky and cracking. while driving during the day when the sun is out, it creates a glare right at eye level causing unsafe visibility issues. it is also a sticky mess, which causes dust, dead bugs and hair to stick to my dashboard. .0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF9A1. Mazda Mazda3 2010 problem was reported in CAPE CORAL, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Structure Body

Mazda Mazda3 2010 Structure Body Review #10626117

MAZDA MAZDA3 2010 car safety problem was reported on July 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE:BODY . the dashboard is melting. the reflection from the melting, shiny, dashboard can make driving difficult at times because the reflections from the dashboard onto the front windshield can negatively affect visibility. .0 person(s) were injured. 0 person(s) died.Mileage was 51000 miles. Vehicle Identification Number (VIN):JM1BL1SF2A1. Mazda Mazda3 2010 problem was reported in ST. PETERSBURG, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 25 mph.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10626117

MAZDA MAZDA3 2010 car safety problem was reported on July 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . the dashboard is melting. the reflection from the melting, shiny, dashboard can make driving difficult at times because the reflections from the dashboard onto the front windshield can negatively affect visibility. .0 person(s) were injured. 0 person(s) died.Mileage was 51000 miles. Vehicle Identification Number (VIN):JM1BL1SF2A1. Mazda Mazda3 2010 problem was reported in ST. PETERSBURG, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 25 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10626346

MAZDA MAZDA3 2010 car safety problem was reported on Aug 12, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dashboard is melting in the florida heat. not much else to explain but that when it's left in the sun it melts..0 person(s) were injured. 0 person(s) died.Mileage was 80000 miles. Vehicle Identification Number (VIN):JM1BL1SF4A1. Mazda Mazda3 2010 problem was reported in MT DORA, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Structure Body

Mazda Mazda3 2010 Structure Body Review #10626346

MAZDA MAZDA3 2010 car safety problem was reported on Aug 12, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE:BODY . the dashboard is melting in the florida heat. not much else to explain but that when it's left in the sun it melts..0 person(s) were injured. 0 person(s) died.Mileage was 80000 miles. Vehicle Identification Number (VIN):JM1BL1SF4A1. Mazda Mazda3 2010 problem was reported in MT DORA, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10626622

MAZDA MAZDA3 2010 car safety problem was reported on Mar 24, 2011.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with WHEELS . replaced 1st of 16 tires to date. since owning this car, we've had to replace tires 1x/year. this is due to the overly aggressive camber on the car. during this time, we've taken it to 2 separate mazda dealers who deny any defect in the car. as a last resort we've contacted mazda, na, who referred us back to one of the dealers we've dealt with in the past. their solution was additional rotations and alignments. you can't align camber when it meets the manufacturer's specifications that cause the tires to wear on the inner side prematurely. we have 80,500 miles on the car and have put on 4 sets of tires. mazda denies any defect, just as they did 20 years ago with a seat belt problem that resulted in a recall after government intervention. the tire issue is a safety issue in that the wear is out of sight. this last pair of tires were purchased due to a blowout on a major road and having to change to the donut while on the shoulder. mazda will not back their vehicles, so don't buy them!.0 person(s) were injured. 0 person(s) died.Mileage was 15489 miles. Vehicle Identification Number (VIN):JM1BL1H65A1. Mazda Mazda3 2010 problem was reported in MILFORD, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10627015

MAZDA MAZDA3 2010 car safety problem was reported on Aug 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . for about a year now i have been noticing that my dashboard has been melting. it has gotten successively worse to the point now that the melting dashboard is reflecting on the windshield. the reflection has gotten so bad during the day when the sun is out that the visibility is greatly impaired. my son was driving the car the other day and he told me he could not see out because of the glare. that is the point where i decided to contact the manufacturer. it seems that they will pay for the part but they are asking me to pay $170.00 for the labor. this is happening through no fault of my own. it is a safety risk for whoever is driving the car and should therefore be covered completely by the manufacturer before there is lives lost through this..0 person(s) were injured. 0 person(s) died.Mileage was 50000 miles. Vehicle Identification Number (VIN):JM1BL1SF7A1. Mazda Mazda3 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Structure

Mazda Mazda3 2010 Structure Review #10627126

MAZDA MAZDA3 2010 car safety problem was reported on July 07, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE . tl* the contact owns a 2010 mazda 3. the contact stated that the dashboard was melting. the vehicle was taken to a dealer for diagnostic testing, but the mechanic was unable to determine the cause of the failure. the vehicle was not repaired and the manufacturer was notified. the approximate failure mileage was 25,250..0 person(s) were injured. 0 person(s) died.Mileage was 25250 miles. Vehicle Identification Number (VIN):JM1BL1SF7A1. Mazda Mazda3 2010 problem was reported in MEMPHIS, TN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10628154

MAZDA MAZDA3 2010 car safety problem was reported on Dec 10, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . dashboard melted from heat, made the dashboard sticky and shinny to the point where visibility can be affected if the sun hits it the right way making it difficult to see spots in the road. potential hazard to hit, property, pets, or even small children. if they can recall mazda for spiders in their engines then we should be able to recall to fix this visibility hazard..0 person(s) were injured. 0 person(s) died.Mazda Mazda3 2010 problem was reported in PLANTATION, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Structure Body

Mazda Mazda3 2010 Structure Body Review #10628423

MAZDA MAZDA3 2010 car safety problem was reported on May 13, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE:BODY . tl* the contact owns a 2010 mazda. the contact stated that the dashboard in the vehicle was melting. the contact mentioned the melted dashboard reflects onto the windshield and caused a glare that would affect the contacts visibility. the vehicle was taken to a dealer. the vehicle was not repaired. the manufacturer was made aware of the failure. the failure was mileage was 38,000. updated 10/09/14*lj.0 person(s) were injured. 0 person(s) died.Mileage was 38000 miles. Vehicle Identification Number (VIN):JM1BL1SF3A1. Mazda Mazda3 2010 problem was reported in PALM COAST, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda Mazda3 2010 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10628609

MAZDA MAZDA3 2010 car safety problem was reported on Apr 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . dashboard is melting and causing glare on windshield. continues to get progressively worse with the heat. visibility getting worse as well. .0 person(s) were injured. 0 person(s) died.Mileage was 48000 miles. Vehicle Identification Number (VIN):JM1BL1H55A1. Mazda Mazda3 2010 problem was reported in ST. PETERSBURG, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10628609

MAZDA MAZDA3 2010 car safety problem was reported on Apr 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . dashboard is melting and causing glare on windshield. continues to get progressively worse with the heat. visibility getting worse as well. .0 person(s) were injured. 0 person(s) died.Mileage was 48000 miles. Vehicle Identification Number (VIN):JM1BL1H55A1. Mazda Mazda3 2010 problem was reported in ST. PETERSBURG, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10628636

MAZDA MAZDA3 2010 car safety problem was reported on Aug 27, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . dashboard is melting on my daughters car.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF1A1. Mazda Mazda3 2010 problem was reported in JUPITER, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10628671

MAZDA MAZDA3 2010 car safety problem was reported on May 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . black 2010 mazda 3, purchased used in december 2011; about a year and a half later the dash started getting sticky and now it is literally melting. i have never used any cleaning products on the interior of the car and when i do clean the inside of my car, i use a soft towel. now i cant even clean my dashboard, due to the stickiness and possibility of ruining it even more. the dash causes a severe glare while driving and i feel this lack of visibility is a hazard to the operator of the vehicle, passengers, other drivers, and pedestrians..0 person(s) were injured. 0 person(s) died.Mileage was 50000 miles. Vehicle Identification Number (VIN):JM1BL1SF0A1. Mazda Mazda3 2010 problem was reported in ROYAL PALM BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10628671

MAZDA MAZDA3 2010 car safety problem was reported on May 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . black 2010 mazda 3, purchased used in december 2011; about a year and a half later the dash started getting sticky and now it is literally melting. i have never used any cleaning products on the interior of the car and when i do clean the inside of my car, i use a soft towel. now i cant even clean my dashboard, due to the stickiness and possibility of ruining it even more. the dash causes a severe glare while driving and i feel this lack of visibility is a hazard to the operator of the vehicle, passengers, other drivers, and pedestrians..0 person(s) were injured. 0 person(s) died.Mileage was 50000 miles. Vehicle Identification Number (VIN):JM1BL1SF0A1. Mazda Mazda3 2010 problem was reported in ROYAL PALM BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other Review #10628919

MAZDA MAZDA3 2010 car safety problem was reported on May 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the top of the dashboard near the windshield is melting. the dashboard is sticky to the touch and has a very glossy look to it. when driving during certain times of the day, the dashboard causes a glare on the windshield in front of the driver making it difficult to see while driving the vehicle..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF4A1. Mazda Mazda3 2010 problem was reported in SPRING HILL, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10628925

MAZDA MAZDA3 2010 car safety problem was reported on May 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . dashboard is melting, which has made the surface highly reflective. this results in poor visibility when it reflects into the windshield. could lead to accident if it remains as-is. .0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF0A1. Mazda Mazda3 2010 problem was reported in TUCSON, AZ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper Review #10629870

MAZDA MAZDA3 2010 car safety problem was reported on Mar 24, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . dashboard melting .0 person(s) were injured. 0 person(s) died.Mileage was 50000 miles. Vehicle Identification Number (VIN):JM1BL1SF4A1. Mazda Mazda3 2010 problem was reported in NORTH LAUDERDALE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10629925

MAZDA MAZDA3 2010 car safety problem was reported on Sept 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . car's dashboard is melting close to the windshield. it is shiny and sticky, and the reflection of the shining dash can sometimes be seen in the windshield. .0 person(s) were injured. 0 person(s) died.Mileage was 37543 miles. Vehicle Identification Number (VIN):JM1BL1SF5A1. Mazda Mazda3 2010 problem was reported in WINTER PARK, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10629925

MAZDA MAZDA3 2010 car safety problem was reported on Sept 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . car's dashboard is melting close to the windshield. it is shiny and sticky, and the reflection of the shining dash can sometimes be seen in the windshield. .0 person(s) were injured. 0 person(s) died.Mileage was 37543 miles. Vehicle Identification Number (VIN):JM1BL1SF5A1. Mazda Mazda3 2010 problem was reported in WINTER PARK, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10629984

MAZDA MAZDA3 2010 car safety problem was reported on Aug 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . vehicle has the melting dashboard issue reported on nissan, mazda, lexus and toyota http://www.abcactionnews.com/money/consumer/taking-action-for-you/hundreds-of-drivers-say-their-dashboard-is-melting-and-car-makers-are-not-issuing-a-recall http://www.mazda3forums.com/showthread.php?t=458121.0 person(s) were injured. 0 person(s) died.Mileage was 34500 miles. Vehicle Identification Number (VIN):JM1BL1H55A1. Mazda Mazda3 2010 problem was reported in TAMPA, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other Review #10630182

MAZDA MAZDA3 2010 car safety problem was reported on Aug 15, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . dashboard is melting. it has not been exposed to any chemicals that would cause it. .0 person(s) were injured. 0 person(s) died.Mileage was 49000 miles. Mazda Mazda3 2010 problem was reported in PORT ORANGE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10630293

MAZDA MAZDA3 2010 car safety problem was reported on Sept 03, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dashboard is melting causing a reflection on the front window which is a driving hazard as the reflection on the window causes limited visibility while driving. dashboard is melted and sticky to the touch, mostly in front of the drivers side but also to a lesser degree on passenger side. no chemicals have been used on the dashboard..0 person(s) were injured. 0 person(s) died.Mazda Mazda3 2010 problem was reported in HOUSTON, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Structure Body

Mazda Mazda3 2010 Structure Body Review #10630524

MAZDA MAZDA3 2010 car safety problem was reported on Jan 06, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE:BODY . the dashboard is melting!! it appears that it is deteriorating causing visibility issues. it is becoming sticky and apparently is a manufacturer defect. as the sun glares down on the windshield, the suns' rays bounce off the shiny dashboard causing me to lose vision in traffic. the mazda dealer is not wanting to replace it stating it is out of warranty. they want me to pay over $400 for the labor and 50% of the part. i even called the mazda hq and they refuse to cover the damage, stating they could do nothing better than the offer the dealership gave me. i requested to speak to higher up management at corporate but was told by the representative that nobody could assist me further. this is so absurd!!! please help before i have an accident. .0 person(s) were injured. 0 person(s) died.Mileage was 28000 miles. Vehicle Identification Number (VIN):JM1BL1SF5A1. Mazda Mazda3 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10630524

MAZDA MAZDA3 2010 car safety problem was reported on Jan 06, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . the dashboard is melting!! it appears that it is deteriorating causing visibility issues. it is becoming sticky and apparently is a manufacturer defect. as the sun glares down on the windshield, the suns' rays bounce off the shiny dashboard causing me to lose vision in traffic. the mazda dealer is not wanting to replace it stating it is out of warranty. they want me to pay over $400 for the labor and 50% of the part. i even called the mazda hq and they refuse to cover the damage, stating they could do nothing better than the offer the dealership gave me. i requested to speak to higher up management at corporate but was told by the representative that nobody could assist me further. this is so absurd!!! please help before i have an accident. .0 person(s) were injured. 0 person(s) died.Mileage was 28000 miles. Vehicle Identification Number (VIN):JM1BL1SF5A1. Mazda Mazda3 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10630524

MAZDA MAZDA3 2010 car safety problem was reported on Jan 06, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dashboard is melting!! it appears that it is deteriorating causing visibility issues. it is becoming sticky and apparently is a manufacturer defect. as the sun glares down on the windshield, the suns' rays bounce off the shiny dashboard causing me to lose vision in traffic. the mazda dealer is not wanting to replace it stating it is out of warranty. they want me to pay over $400 for the labor and 50% of the part. i even called the mazda hq and they refuse to cover the damage, stating they could do nothing better than the offer the dealership gave me. i requested to speak to higher up management at corporate but was told by the representative that nobody could assist me further. this is so absurd!!! please help before i have an accident. .0 person(s) were injured. 0 person(s) died.Mileage was 28000 miles. Vehicle Identification Number (VIN):JM1BL1SF5A1. Mazda Mazda3 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other Review #10630792

MAZDA MAZDA3 2010 car safety problem was reported on Apr 02, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . i have a 2010 mazda 3, bought brand new, off the lot in 2010 and the dashboard is melting, causing a severe glare on the windshield. this is causing me a driving hazard as the glare makes it hard to see! the dash material is also cracking and melting around the ac vents. .0 person(s) were injured. 0 person(s) died.Mazda Mazda3 2010 problem was reported in PALM BEACH GARDENS, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10631099

MAZDA MAZDA3 2010 car safety problem was reported on July 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dashboard of my mazda3 seems to be melting. the bright shiny plastic is creating a glare that hinders my vision while driving. the plastic is sticky to the touch. also, when my car has been sitting for awhile during the day it smells of melted plastic when you get back into it. .0 person(s) were injured. 0 person(s) died.Mazda Mazda3 2010 problem was reported in PORT WENTWORTH, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10631134

MAZDA MAZDA3 2010 car safety problem was reported on Sept 10, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dashboard is melting away, very sticky and very shiny causing the sun to impair vision as i'm driving. .0 person(s) were injured. 0 person(s) died.Mileage was 45000 miles. Vehicle Identification Number (VIN):JM1BL1SF6A1. Mazda Mazda3 2010 problem was reported in SANFORD, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10631285

MAZDA MAZDA3 2010 car safety problem was reported on Sept 06, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . my mazda 2010 dashboard appears to be melting.0 person(s) were injured. 0 person(s) died.Mileage was 57000 miles. Mazda Mazda3 2010 problem was reported in RIVERVIEW, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other Review #10631314

MAZDA MAZDA3 2010 car safety problem was reported on Sept 07, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . my dashboard is melting and has been for the last year. the glare this causes on the windshield makes it hard to see..0 person(s) were injured. 0 person(s) died.Mileage was 20000 miles. Vehicle Identification Number (VIN):JM1BL1SF5A1. Mazda Mazda3 2010 problem was reported in RIVIERA BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10632190

MAZDA MAZDA3 2010 car safety problem was reported on Dec 30, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . the dashboard is melting on the mound above the steering wheel, in direct line of view of road and continues to spread. sticky glue type texture that never dries. unable to put a sun blocker in the vehicle to contain the spreading issue and while driving it creates glare..0 person(s) were injured. 0 person(s) died.Mileage was 20000 miles. Mazda Mazda3 2010 problem was reported in COVINGTON, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10632190

MAZDA MAZDA3 2010 car safety problem was reported on Dec 30, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dashboard is melting on the mound above the steering wheel, in direct line of view of road and continues to spread. sticky glue type texture that never dries. unable to put a sun blocker in the vehicle to contain the spreading issue and while driving it creates glare..0 person(s) were injured. 0 person(s) died.Mileage was 20000 miles. Mazda Mazda3 2010 problem was reported in COVINGTON, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other Review #10632328

MAZDA MAZDA3 2010 car safety problem was reported on Jan 13, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . my mazda3 dashboard is melting. i have never used any chemical substances to clean the interior of my car. i live in south florida and i've recently been using a sunshade protector but that doesn't not seem to be helping. the glare from the dashboard affects my vision of the road. i constantly have to clean my windshield with mild dish soap because the residue transfer from my sunshade onto my windshield. the cost of replacing my dashboard is not included in my extended waranty package. i have complained to my mazda dealer on multiple occasions, but i was told that i would have to pay $1,200.00 to replace this problem. is there anything that can be done? .0 person(s) were injured. 0 person(s) died.Mileage was 63000 miles. Vehicle Identification Number (VIN):JM1BL1SF3A1. Mazda Mazda3 2010 problem was reported in MIRAMAR, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10632427

MAZDA MAZDA3 2010 car safety problem was reported on Sept 05, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . i noticed that my dash board has started to melt creating a visibility problems. it is very sticky..0 person(s) were injured. 0 person(s) died.Mazda Mazda3 2010 problem was reported in PUNTA GORDA, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Exterior Lighting

Mazda Mazda3 2010 Exterior Lighting Review #10632527

MAZDA MAZDA3 2010 car safety problem was reported on May 31, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with EXTERIOR LIGHTING . i have noticed that my headlight assemblies fill up with water and condensation after rain showers or car washes. no modifications have been done to these assemblies..0 person(s) were injured. 0 person(s) died.Mazda Mazda3 2010 problem was reported in SCHAUMBURG, IL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10632969

MAZDA MAZDA3 2010 car safety problem was reported on Sept 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . my dashboard began to melt, and has continued to do so since. the dashboard is sticky and collections dust and grim. the melted material has a glossy shine which reflects a bright glare into the drivers eyes and onto the windshield. it is cosmetically unattractive and causes a driving hazard when operating the vehicle. .0 person(s) were injured. 0 person(s) died.Mileage was 70000 miles. Mazda Mazda3 2010 problem was reported in SLIDELL, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10632969

MAZDA MAZDA3 2010 car safety problem was reported on Sept 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . my dashboard began to melt, and has continued to do so since. the dashboard is sticky and collections dust and grim. the melted material has a glossy shine which reflects a bright glare into the drivers eyes and onto the windshield. it is cosmetically unattractive and causes a driving hazard when operating the vehicle. .0 person(s) were injured. 0 person(s) died.Mileage was 70000 miles. Mazda Mazda3 2010 problem was reported in SLIDELL, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10633478

MAZDA MAZDA3 2010 car safety problem was reported on Aug 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . my daughter's 2010 mazda3 has a dashboard that is melting. she says the glare from it when driving is very bad. this is a major safety issue and from what i am seeing regarding complaints, there are many complaints regarding this. why has this not been addressed as a recall? it is obviously a manufacturer defect?.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF1A1. Mazda Mazda3 2010 problem was reported in JUPITER, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Electrical System

Mazda Mazda3 2010 Electrical System Review #10633500

MAZDA MAZDA3 2010 car safety problem was reported on July 01, 2009.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with ELECTRICAL SYSTEM . when the trunk or door is inadvertently left open for an extended period of time the battery is totally drained. this could leave the driver stranded. if jump started and battery is not fully charged this could cause increased stress on the alternator which could lead to costly replacement..0 person(s) were injured. 0 person(s) died.Mileage was 0 miles. Vehicle Identification Number (VIN):JM1BL1S56A1. Mazda Mazda3 2010 problem was reported in MCKINNEY, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10637340

MAZDA MAZDA3 2010 car safety problem was reported on Sept 09, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . i have a dash that is melting. it is over the instrument cluster and is turning to a tarry like substance. i does have a lot of reflection and could cause some vision impairment from the glare it produces. i think it is a design flaw. the above incident date is when i noticed the dash..0 person(s) were injured. 0 person(s) died.Mileage was 40075 miles. Vehicle Identification Number (VIN):JM1BL1H57A1. Mazda Mazda3 2010 problem was reported in WINSTON SALEM, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Steering

Mazda Mazda3 2010 Steering Review #10637562

MAZDA MAZDA3 2010 car safety problem was reported on Aug 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STEERING . i was driving on a standard 40 mph busy street when i turned a corner and my power steering completely failed, i narrowly missed hitting a pole. i took it into a mazda dealership in hopes that it would be honored in the mazda3 2009 recall or perhaps it could be honored in a warranty, but was told no. i filed an official complaint with mazda but was further denied, they would not help me in any way reconcile the $1200 cost of the repair nor would they issue another recall. my life was at risk and i was put under terrible distress during and after this situation with the cost of repairs to this systematic design flaw. i filed a second complaint with mazda customer experience asking for reimbursement but was still denied. this is a serious issue that persists in models outside of the 2009 power steering recall and mazda needs to take responsibility for the safety of their cars and all drivers..0 person(s) were injured. 0 person(s) died.Mileage was 46199 miles. Vehicle Identification Number (VIN):JM1BL1SG2A1. Mazda Mazda3 2010 problem was reported in ORANGE, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10637681

MAZDA MAZDA3 2010 car safety problem was reported on July 17, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . dashboard on the driver side began to melt, and continued to do so. the dashboard is sticky and collects dust and grim. the melted material has a glossy shine reflecting a bright glare into the drivers eyes and onto the windshield. it causes a driving hazard when operating the vehicle..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1S5XA1. Mazda Mazda3 2010 problem was reported in CAPE CORAL, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10637681

MAZDA MAZDA3 2010 car safety problem was reported on July 17, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . dashboard on the driver side began to melt, and continued to do so. the dashboard is sticky and collects dust and grim. the melted material has a glossy shine reflecting a bright glare into the drivers eyes and onto the windshield. it causes a driving hazard when operating the vehicle..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1S5XA1. Mazda Mazda3 2010 problem was reported in CAPE CORAL, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10637712

MAZDA MAZDA3 2010 car safety problem was reported on Feb 11, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . interior dashboard melting causing blinding glare and stickiness to anything placed on top of it. .0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF5A1. Mazda Mazda3 2010 problem was reported in SUNRISE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10638625

MAZDA MAZDA3 2010 car safety problem was reported on Oct 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dashboard is "melting". the polymers are breaking down, it is sticky, and causing a glare on the road/when driving which is dangerous. .0 person(s) were injured. 0 person(s) died.Mileage was 42000 miles. Vehicle Identification Number (VIN):JM1BL1SF8A1. Mazda Mazda3 2010 problem was reported in HUDSON, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other Review #10640182

MAZDA MAZDA3 2010 car safety problem was reported on Jan 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . my dashboard is melting. the glare gets so bad i can't see out of the windshield..0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Vehicle Identification Number (VIN):JM1BL1SF1A1. Mazda Mazda3 2010 problem was reported in DELTONA, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Exterior Lighting

Mazda Mazda3 2010 Exterior Lighting Review #10640462

MAZDA MAZDA3 2010 car safety problem was reported on Sept 27, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with EXTERIOR LIGHTING . moisture has entered both head lamps causing failure of bulbs and hid control units. complete lighting failure while driving. .0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Vehicle Identification Number (VIN):JM1BL1S56A1. Mazda Mazda3 2010 problem was reported in LARGO, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Mazda Mazda3 2010 Electrical System

Mazda Mazda3 2010 Electrical System Review #10640462

MAZDA MAZDA3 2010 car safety problem was reported on Sept 27, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with ELECTRICAL SYSTEM . moisture has entered both head lamps causing failure of bulbs and hid control units. complete lighting failure while driving. .0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Vehicle Identification Number (VIN):JM1BL1S56A1. Mazda Mazda3 2010 problem was reported in LARGO, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 35 mph.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10640544

MAZDA MAZDA3 2010 car safety problem was reported on June 06, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with SEATS . drivers seat feel loose and wiggles. unknown how it would hold up during a crash..0 person(s) were injured. 0 person(s) died.Mileage was 28000 miles. Vehicle Identification Number (VIN):JM1BL1S56A1. Mazda Mazda3 2010 problem was reported in LARGO, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10641389

MAZDA MAZDA3 2010 car safety problem was reported on June 09, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . the dashboard on my mazda 3 seems to be melting in hot weather. when the sun shines directly on the dash, it causes a horrible glare on the windshield making it very difficult to see what is directly in front of me. it is the worst in afternoon sunny weather..0 person(s) were injured. 0 person(s) died.Mileage was 70000 miles. Vehicle Identification Number (VIN):JM1BL1SF4A1. Mazda Mazda3 2010 problem was reported in NAVARRE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10641587

MAZDA MAZDA3 2010 car safety problem was reported on Oct 04, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . mazda 3 2010 dash is melting. i have been noticing a glare over the last few months from the dash to the windshield that in sunny conditions was making it difficult to see through the glare. i thought it was potentially some adhesive leaking out of the seam of the dash. it was getting worse over time so this weekend i attempted to clean off the substance. i found that it was not a substance but the dash had become soft and sticky. it was not able to be cleaned off. i have used a sunshade since i owned the car (oct 2009). i have lived in south florida since 1985 and have owned multiple cars. i learned the hard way that you must shade your dash to prevent it from being damaged. however, over the last 30 years, no dash has melted and caused a dangerous glare that is a safety hazard..0 person(s) were injured. 0 person(s) died.Mileage was 38797 miles. Vehicle Identification Number (VIN):JM1BL1S56A1. Mazda Mazda3 2010 problem was reported in MARGATE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10641587

MAZDA MAZDA3 2010 car safety problem was reported on Oct 04, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . mazda 3 2010 dash is melting. i have been noticing a glare over the last few months from the dash to the windshield that in sunny conditions was making it difficult to see through the glare. i thought it was potentially some adhesive leaking out of the seam of the dash. it was getting worse over time so this weekend i attempted to clean off the substance. i found that it was not a substance but the dash had become soft and sticky. it was not able to be cleaned off. i have used a sunshade since i owned the car (oct 2009). i have lived in south florida since 1985 and have owned multiple cars. i learned the hard way that you must shade your dash to prevent it from being damaged. however, over the last 30 years, no dash has melted and caused a dangerous glare that is a safety hazard..0 person(s) were injured. 0 person(s) died.Mileage was 38797 miles. Vehicle Identification Number (VIN):JM1BL1S56A1. Mazda Mazda3 2010 problem was reported in MARGATE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Wheels

Mazda Mazda3 2010 Wheels Review #10643076

MAZDA MAZDA3 2010 car safety problem was reported on Oct 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with WHEELS . i have now had two tpms valve stems snap off while needing to inflate my tires. both cracked in half at the threaded part or the stem. cost is $150 each to replace. mazda corporate says this is "normal". i have driven 500,000 in my life and never had a valve stem crack off. this car has had two. forums are littered with this issue. people complaining of failure while driving and tires going flat on the highway. will someone need to die for mazda to change these dangerous monitors?.0 person(s) were injured. 0 person(s) died.Mazda Mazda3 2010 problem was reported in ELKRIDGE, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10643209

MAZDA MAZDA3 2010 car safety problem was reported on June 02, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . dashboard is melting, creating a shiny surface that creates a severe glare and inhibits vision. this is more than just a cosmetic issue. mazda refused to fix the problem for my 2010 mazda3 with only 47000 miles on it..0 person(s) were injured. 0 person(s) died.Mileage was 44000 miles. Vehicle Identification Number (VIN):JM1BL1H52A1. Mazda Mazda3 2010 problem was reported in PLANO, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10643272

MAZDA MAZDA3 2010 car safety problem was reported on Oct 08, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . my dashboard is melting with the consistency of peanut butter. i have brought the car to mazda and they will not stand behind their car..0 person(s) were injured. 0 person(s) died.Mileage was 66000 miles. Vehicle Identification Number (VIN):JM1BL1SF4A1. Mazda Mazda3 2010 problem was reported in DAYTONA BEACH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10643459

MAZDA MAZDA3 2010 car safety problem was reported on Jan 10, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . the dashboard on my 2010 mazda 3 began melting at the beginning of the year. over time, more of the dashboard has become sticky and shiny. sometimes the shininess is so reflective that it makes it difficult for me to see when i am driving on a sunny day. the vehicle resides in hawaii and is kept in a garage when not in use..0 person(s) were injured. 0 person(s) died.Mileage was 30000 miles. Vehicle Identification Number (VIN):JM1BL1SF0A1. Mazda Mazda3 2010 problem was reported in KAILUA-KONA, HI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10643459

MAZDA MAZDA3 2010 car safety problem was reported on Jan 10, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dashboard on my 2010 mazda 3 began melting at the beginning of the year. over time, more of the dashboard has become sticky and shiny. sometimes the shininess is so reflective that it makes it difficult for me to see when i am driving on a sunny day. the vehicle resides in hawaii and is kept in a garage when not in use..0 person(s) were injured. 0 person(s) died.Mileage was 30000 miles. Vehicle Identification Number (VIN):JM1BL1SF0A1. Mazda Mazda3 2010 problem was reported in KAILUA-KONA, HI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other Review #10643941

MAZDA MAZDA3 2010 car safety problem was reported on Oct 10, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dash of my mazda 3 2010 is literally melting. this cause a glare when driving that can't be avoided. this makes driving very dangerous in sunny conditions..0 person(s) were injured. 0 person(s) died.Mileage was 138000 miles. Vehicle Identification Number (VIN):JM1BL1SFXA1. Mazda Mazda3 2010 problem was reported in KINGSTREE, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10643979

MAZDA MAZDA3 2010 car safety problem was reported on Oct 10, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . the dashboard on my 2010 mazda 3 has began melting. the dashboard has become sticky and shiny. sometimes the shininess is so reflective that it makes it difficult for me to see when i am driving on a sunny day. there are chunks of the dash that come off like chewing gum. the dash gets on everything like sticky black tar. i can only imagine that there are dangerous toxins being released into the air to breathe while driving knowing that this synthetic material has now broken down and begun to deteriorate. the car is only four years old and well cared for. who is to blame for my loss loss of value from a poorly made product. .0 person(s) were injured. 0 person(s) died.Mileage was 42000 miles. Vehicle Identification Number (VIN):JM1BL1H54A1. Mazda Mazda3 2010 problem was reported in KAILUA, HI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Structure

Mazda Mazda3 2010 Structure Review #10644800

MAZDA MAZDA3 2010 car safety problem was reported on Oct 14, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE . tl* the contact owns a 2010 mazda 3. the contact stated that the dashboard bega deteriorating. the contact noticed that there was a sticky substance accumulating as the failure was became progressively worse. the vehicle was not diagnosed or repaired. the manufacturer was notified of the failure. the approximate failure mileage was 63,000. .0 person(s) were injured. 0 person(s) died.Mileage was 63000 miles. Vehicle Identification Number (VIN):JM1BL1H50A1. Mazda Mazda3 2010 problem was reported in PFLUGERVIILE, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Service Brakes

Mazda Mazda3 2010 Service Brakes Review #10644947

MAZDA MAZDA3 2010 car safety problem was reported on Oct 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with SERVICE BRAKES . the abs & dsc (dynamic stability control) instrument panel warning lights came on. i have had the car tested at a repair shop and two separate computer readouts show codes c0020, u0140 & u0140 (related to the abs hydraulic unit). the shop provided service bulletin no. 04-002/13, last issued: 7/17/2013 related to this problem. i understand i may not have functional abs or dsc but the brakes, while not having abs, still function. i was advised this may be a very expensive repair but since it is a safety related issue, mazda may fix the problem at no charge. i would argue that not having abs or dsc is most certainly a safety issue and i should have received a recall notice. please advise..0 person(s) were injured. 0 person(s) died.Mileage was 22000 miles. Vehicle Identification Number (VIN):JM1BL1H60A1. Mazda Mazda3 2010 problem was reported in BALTIMORE, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 5 mph.

Mazda Mazda3 2010 Electronic Stability Control

Mazda Mazda3 2010 Electronic Stability Control Review #10644947

MAZDA MAZDA3 2010 car safety problem was reported on Oct 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with ELECTRONIC STABILITY CONTROL . the abs & dsc (dynamic stability control) instrument panel warning lights came on. i have had the car tested at a repair shop and two separate computer readouts show codes c0020, u0140 & u0140 (related to the abs hydraulic unit). the shop provided service bulletin no. 04-002/13, last issued: 7/17/2013 related to this problem. i understand i may not have functional abs or dsc but the brakes, while not having abs, still function. i was advised this may be a very expensive repair but since it is a safety related issue, mazda may fix the problem at no charge. i would argue that not having abs or dsc is most certainly a safety issue and i should have received a recall notice. please advise..0 person(s) were injured. 0 person(s) died.Mileage was 22000 miles. Vehicle Identification Number (VIN):JM1BL1H60A1. Mazda Mazda3 2010 problem was reported in BALTIMORE, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 5 mph.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10649207

MAZDA MAZDA3 2010 car safety problem was reported on Oct 21, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with SEATS . i was driving down the road and heard/felt a clunk and the driver seat tilted back a few inches and became unstable. the seat now moves freely up and down and is not currently safe to drive. this was a result of weld on the seat bracket breaking and the seat losing its support. i looked online and found over 100 complaints for the same issue..0 person(s) were injured. 0 person(s) died.Mileage was 66721 miles. Vehicle Identification Number (VIN):JM1BL1S67A1. Mazda Mazda3 2010 problem was reported in WHITTIER, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10649552

MAZDA MAZDA3 2010 car safety problem was reported on Nov 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . bought this car used in june 2013, and noticed in november of 2013 it started to become sticky on the dashboard as if it is melting.. didnt really become an issue until it began to glare into my windshield causing me to be unable to see. i cannot clean, or touch any part of the dashboard because it is so melted and sticky it sticks to my hands if i do. it is in my direct view of where i should be looking towards the road. huge issue that needs to be addressed. .0 person(s) were injured. 0 person(s) died.Mileage was 58000 miles. Vehicle Identification Number (VIN):JM1BL1SF1A1. Mazda Mazda3 2010 problem was reported in LAKE WORTH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10649552

MAZDA MAZDA3 2010 car safety problem was reported on Nov 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . bought this car used in june 2013, and noticed in november of 2013 it started to become sticky on the dashboard as if it is melting.. didnt really become an issue until it began to glare into my windshield causing me to be unable to see. i cannot clean, or touch any part of the dashboard because it is so melted and sticky it sticks to my hands if i do. it is in my direct view of where i should be looking towards the road. huge issue that needs to be addressed. .0 person(s) were injured. 0 person(s) died.Mileage was 58000 miles. Vehicle Identification Number (VIN):JM1BL1SF1A1. Mazda Mazda3 2010 problem was reported in LAKE WORTH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10650085

MAZDA MAZDA3 2010 car safety problem was reported on Oct 20, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . the dashboard in the car is melting - to the point that the glare is affecting the view.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF1A1. Mazda Mazda3 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper Review #10650508

MAZDA MAZDA3 2010 car safety problem was reported on Oct 27, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . the dashboard on this vehicle is melting. i purchased it used in april and noticed about 1 month later that the dash was sticky. over the last few months, it has gotten progressively worse on the driver's side to the point that the glare causes visibility issues for the driver..0 person(s) were injured. 0 person(s) died.Mileage was 48000 miles. Vehicle Identification Number (VIN):JM1BL1SF3A1. Mazda Mazda3 2010 problem was reported in DENTON, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10650646

MAZDA MAZDA3 2010 car safety problem was reported on July 23, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . dashboard "melted". it's shiny ( bad glare) and very sticky as though the glue has risen up through it..0 person(s) were injured. 0 person(s) died.Mileage was 60000 miles. Vehicle Identification Number (VIN):JM1BL1S55A1. Mazda Mazda3 2010 problem was reported in AVENTURA, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other Review #10651067

MAZDA MAZDA3 2010 car safety problem was reported on July 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dashboard within my vechile is metling. it is a gooey, sticky area all the way across the dashboard. it creates a reflective glare that interferes with my driving. .0 person(s) were injured. 0 person(s) died.Mazda Mazda3 2010 problem was reported in PORT ST LUCIE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10651469

MAZDA MAZDA3 2010 car safety problem was reported on Jan 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the top of my dashboard has melted. it has a sticky, shiny texture now. i live in florida, so i guess it melted from the heat. it's so bad i can't put anything near or on it for fear it might get ruined by the dashboard (ex: parking passes). the glare sometimes gets bad enough where it obstructs my vision while driving. the car is just about 5 years old now, but the dashboard has been melted for a long time. i'm not sure what to do about it. there must be some kind of health risk from driving around with melting plastic in front of your face..0 person(s) were injured. 0 person(s) died.Mazda Mazda3 2010 problem was reported in LAKE WORTH, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10651992

MAZDA MAZDA3 2010 car safety problem was reported on June 01, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . my dash board is melting and during the day it is hard to see out the front windshield due to the glare the melting dash board. the front hood paint is chipping off only on select sections over the engine. .0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF1A1. Mazda Mazda3 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Structure Body

Mazda Mazda3 2010 Structure Body Review #10651992

MAZDA MAZDA3 2010 car safety problem was reported on June 01, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE:BODY . my dash board is melting and during the day it is hard to see out the front windshield due to the glare the melting dash board. the front hood paint is chipping off only on select sections over the engine. .0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF1A1. Mazda Mazda3 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10652401

MAZDA MAZDA3 2010 car safety problem was reported on Nov 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . the glue is melts on my dashbord causing a glare on the window. it makes it difficult for me to see when i'm driving on a sunny day. the dashbord is verry sticky. .0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SFXA1. Mazda Mazda3 2010 problem was reported in ENTERPRISE, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10652401

MAZDA MAZDA3 2010 car safety problem was reported on Nov 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the glue is melts on my dashbord causing a glare on the window. it makes it difficult for me to see when i'm driving on a sunny day. the dashbord is verry sticky. .0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SFXA1. Mazda Mazda3 2010 problem was reported in ENTERPRISE, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10652455

MAZDA MAZDA3 2010 car safety problem was reported on Nov 07, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . unable to see out front windshield due to glare from melting dashboard with sun hitting at certain angles. .0 person(s) were injured. 0 person(s) died.Mileage was 21000 miles. Vehicle Identification Number (VIN):JM1BL1S56A1. Mazda Mazda3 2010 problem was reported in LARGO, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 45 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10652474

MAZDA MAZDA3 2010 car safety problem was reported on Aug 20, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . multiple times, starting in the summer of the vehicle's fourth year, i have been unable to see clearly through the windshield due to the glare from the melting dashboard. luckily it has not caused any injuries or death due to the fact that i was aware of the problem and more diligent of others on the road..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF9A1. Mazda Mazda3 2010 problem was reported in TARPON SPRINGS, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10652728

MAZDA MAZDA3 2010 car safety problem was reported on Sept 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the front dash in my vehicle has been melting and keeps getting worse as time goes on. when i rub a cloth across it, the fabric sticks to the dash. i'm very good about using a sunshield when parked outside, but this has not prevented the melting..0 person(s) were injured. 0 person(s) died.Mileage was 32000 miles. Vehicle Identification Number (VIN):JM1BL1S50A1. Mazda Mazda3 2010 problem was reported in LARGO, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10653374

MAZDA MAZDA3 2010 car safety problem was reported on Jan 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . my dashboard has been increasingly sticky for years now, despite all attempts to clean it. it has increased to the point of reflecting off of the dashboard and distracting me when i drive. i took it into the mazda dealership and they informed me that the dashboard is melting. i cannot imagine the chemicals are good to breathe in..0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Vehicle Identification Number (VIN):JM1BL1SF3A1. Mazda Mazda3 2010 problem was reported in MIAMI SHORES, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Structure Body

Mazda Mazda3 2010 Structure Body Review #10653374

MAZDA MAZDA3 2010 car safety problem was reported on Jan 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE:BODY . my dashboard has been increasingly sticky for years now, despite all attempts to clean it. it has increased to the point of reflecting off of the dashboard and distracting me when i drive. i took it into the mazda dealership and they informed me that the dashboard is melting. i cannot imagine the chemicals are good to breathe in..0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Vehicle Identification Number (VIN):JM1BL1SF3A1. Mazda Mazda3 2010 problem was reported in MIAMI SHORES, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10653374

MAZDA MAZDA3 2010 car safety problem was reported on Jan 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . my dashboard has been increasingly sticky for years now, despite all attempts to clean it. it has increased to the point of reflecting off of the dashboard and distracting me when i drive. i took it into the mazda dealership and they informed me that the dashboard is melting. i cannot imagine the chemicals are good to breathe in..0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Vehicle Identification Number (VIN):JM1BL1SF3A1. Mazda Mazda3 2010 problem was reported in MIAMI SHORES, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other Review #10653745

MAZDA MAZDA3 2010 car safety problem was reported on Nov 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dashboard material is melting. it produces a glare on the windshield on sunny days creating an unsafe driving condition..0 person(s) were injured. 0 person(s) died.Mileage was 30000 miles. Mazda Mazda3 2010 problem was reported in KATY, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10654275

MAZDA MAZDA3 2010 car safety problem was reported on Feb 14, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . i own a 2010 mazda 3 and the dashboard has melted to the point that it produces a glare on the windshield right at eye level. i tried to have mazda replace it but they said because my warranty had expired they would not do it. i bought the car in 2010 any by 2012 it had started melting. this is clearly a safety hazard for me and everyone else on the road as sometimes it prevents me from seeing out the windshield at all. .0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF8A1. Mazda Mazda3 2010 problem was reported in HONOLULU, HI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10654601

MAZDA MAZDA3 2010 car safety problem was reported on June 12, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . over time, my dashboard began to melt as i cleaned it with soap and water it only got worse! they glare from the dashboard is so bad that at certain times of day i cannot see out of my windshield. this is not safe!.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF0A1. Mazda Mazda3 2010 problem was reported in PINELLAS PARK, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10655128

MAZDA MAZDA3 2010 car safety problem was reported on Nov 03, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . my dashboard (on the driver side and middle) appears to be melting (and sticky) and is causing a significant glare on my windshield reducing my visibility. i am experiencing a lot of difficulty seeing out of my windsheild since it is almost impossible to see out of it at times due to the glare. .0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1S59A1. Mazda Mazda3 2010 problem was reported in PORT SAINT LUCIE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10655128

MAZDA MAZDA3 2010 car safety problem was reported on Nov 03, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . my dashboard (on the driver side and middle) appears to be melting (and sticky) and is causing a significant glare on my windshield reducing my visibility. i am experiencing a lot of difficulty seeing out of my windsheild since it is almost impossible to see out of it at times due to the glare. .0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1S59A1. Mazda Mazda3 2010 problem was reported in PORT SAINT LUCIE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Air Bags

Mazda Mazda3 2010 Air Bags Review #10658876

MAZDA MAZDA3 2010 car safety problem was reported on Oct 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with AIR BAGS . tl* the contact owns a 2010 mazda 3. the contact stated that when the vehicle was started, the air bag warning light illuminated. the vehicle was taken to an independent mechanic. the technician stated that the vehicle was operating as designed. the manufacturer was not notified of the failure. the failure mileage was 50,000. .0 person(s) were injured. 0 person(s) died.Mileage was 50000 miles. Vehicle Identification Number (VIN):JM1BL1SF1A1. Mazda Mazda3 2010 problem was reported in FOREST PARK, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10660288

MAZDA MAZDA3 2010 car safety problem was reported on June 02, 2012.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . dash board melting..0 person(s) were injured. 0 person(s) died.Mileage was 30000 miles. Vehicle Identification Number (VIN):JM1BL1SF4A1. Mazda Mazda3 2010 problem was reported in SPRING HILL, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other Review #10660553

MAZDA MAZDA3 2010 car safety problem was reported on July 23, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . i have a 2010 mazda 3i and the dashboard is melting into a black rubber tar alike substance very sticky and is reflecting onto my windshield blocking my view of traffic after noticing it early on i tried using a windshield visor but to no affect due to the amount of melting the image of the shiny melting rubber is reflecting onto my windsheild now to the point i'm seeing it i can not clean it due to its stickiness and the reflection is getting worse if i can not see what's in front of me is that not a safely concern when your field of view is blocked by a defected part made by mazda its .0 person(s) were injured. 0 person(s) died.Mileage was 76489 miles. Vehicle Identification Number (VIN):JM1BL1SF0A1. Mazda Mazda3 2010 problem was reported in KISSIMMEE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10660553

MAZDA MAZDA3 2010 car safety problem was reported on July 23, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . i have a 2010 mazda 3i and the dashboard is melting into a black rubber tar alike substance very sticky and is reflecting onto my windshield blocking my view of traffic after noticing it early on i tried using a windshield visor but to no affect due to the amount of melting the image of the shiny melting rubber is reflecting onto my windsheild now to the point i'm seeing it i can not clean it due to its stickiness and the reflection is getting worse if i can not see what's in front of me is that not a safely concern when your field of view is blocked by a defected part made by mazda its .0 person(s) were injured. 0 person(s) died.Mileage was 76489 miles. Vehicle Identification Number (VIN):JM1BL1SF0A1. Mazda Mazda3 2010 problem was reported in KISSIMMEE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Vehicle Speed Control

Mazda Mazda3 2010 Vehicle Speed Control Review #10660562

MAZDA MAZDA3 2010 car safety problem was reported on Oct 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2010 mazda mazda3. the contact stated that the cruise control sensor illuminated. the vehicle was not inspected or diagnosed. the vin was not available. the manufacturer was notified of the. the approximate failure mileage was 90,000. .0 person(s) were injured. 0 person(s) died.Mileage was 90000 miles. Mazda Mazda3 2010 problem was reported in HEWITT, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10661217

MAZDA MAZDA3 2010 car safety problem was reported on Mar 03, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . the dash has a goo / has melted from heat smells and has caused a shine that causes difficulty to see as driving..0 person(s) were injured. 0 person(s) died.Mileage was 30024 miles. Vehicle Identification Number (VIN):JM1BL1SF8A1. Mazda Mazda3 2010 problem was reported in NORWALK, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other Review #10661230

MAZDA MAZDA3 2010 car safety problem was reported on Sept 24, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . i left my car in the parking lot at work, and when i came back the dashboard had melted. i live in san antonio tx, and it wasn't a particularly hot day but it melted. i took it to the dealership, and they told me they could not fix it because the warranty had expired. it creates a very bad glare on the windshield which in my opinion, and many other cases that i have heard from is a safety hazard. .0 person(s) were injured. 0 person(s) died.Mileage was 40000 miles. Mazda Mazda3 2010 problem was reported in SAN ANTONIO, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10661326

MAZDA MAZDA3 2010 car safety problem was reported on Nov 30, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with SEATS . driver seat broke while driving, very loose after. upon inspection found that a metal bracket on left rail broke (split in half). .0 person(s) were injured. 0 person(s) died.Mileage was 85464 miles. Vehicle Identification Number (VIN):JM1BL1SG1A1. Mazda Mazda3 2010 problem was reported in POUGHKEEPSIE, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Mazda Mazda3 2010 Engine

Mazda Mazda3 2010 Engine Review #10661792

MAZDA MAZDA3 2010 car safety problem was reported on Dec 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with ENGINE . tl* the contact owns a 2010 mazda 3. while refueling the vehicle, the low oil pressure warning light illuminated and smoke emitted from the exhaust pipe. the vehicle was towed to a dealer but was not diagnosed or repaired. the manufacturer was notified of the failure. the approximate failure mileage was 59,537..0 person(s) were injured. 0 person(s) died.Mileage was 59537 miles. Vehicle Identification Number (VIN):JM1BL1H69A1. Mazda Mazda3 2010 problem was reported in BETHEL PARK, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10662077

MAZDA MAZDA3 2010 car safety problem was reported on Oct 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . dashboard melting and tacky to touch, causes glare when driving, attracts lint and debris due to stickiness..0 person(s) were injured. 0 person(s) died.Mileage was 30000 miles. Vehicle Identification Number (VIN):JM1BL1SFXA1. Mazda Mazda3 2010 problem was reported in PORT ST LUCIE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10662077

MAZDA MAZDA3 2010 car safety problem was reported on Oct 01, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . dashboard melting and tacky to touch, causes glare when driving, attracts lint and debris due to stickiness..0 person(s) were injured. 0 person(s) died.Mileage was 30000 miles. Vehicle Identification Number (VIN):JM1BL1SFXA1. Mazda Mazda3 2010 problem was reported in PORT ST LUCIE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10662146

MAZDA MAZDA3 2010 car safety problem was reported on July 16, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with SEATS . i opened my car and sat down in the drivers seat as per usual only to find that the left side of my seat felt loose. as i leaned forward and backwards i could feel the seat moving with me. i got out and looked under my seat to see what may be loose. what i found was that the part of the seat assembly that attaches to the rail system had come out. i looks like a small metal bolt that goes through a metal rail and is either bolted down on the opposite side or welded together. .0 person(s) were injured. 0 person(s) died.Mileage was 72600 miles. Mazda Mazda3 2010 problem was reported in BROADVIEW HEIGHTS, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10662569

MAZDA MAZDA3 2010 car safety problem was reported on Apr 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . my dashboard is melting (and sticky) and is causing a significant glare on my windshield reducing my visibility. i am experiencing a lot of difficulty seeing out of my windsheild since it is almost impossible to see out of it at times due to the glare..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF0A1. Mazda Mazda3 2010 problem was reported in COOPER CITY, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10662569

MAZDA MAZDA3 2010 car safety problem was reported on Apr 01, 2013.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . my dashboard is melting (and sticky) and is causing a significant glare on my windshield reducing my visibility. i am experiencing a lot of difficulty seeing out of my windsheild since it is almost impossible to see out of it at times due to the glare..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1BL1SF0A1. Mazda Mazda3 2010 problem was reported in COOPER CITY, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10663241

MAZDA MAZDA3 2010 car safety problem was reported on Dec 09, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with SEATS . driver's side seat is becoming loose and "clunking" upon cornering and acceleration. a post to a mazda group, as well as google searches results in hundreds of complains of the seat tracks breaking and this being a "common fix". this should be a huge safety concern that could cause an accident, or cause further injury in the case of an accident. .0 person(s) were injured. 0 person(s) died.Mileage was 63000 miles. Vehicle Identification Number (VIN):JM1BL1S67A1. Mazda Mazda3 2010 problem was reported in FOLLANSBEE, WV. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Seats Review #10664562

MAZDA MAZDA3 2010 car safety problem was reported on Dec 09, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with SEATS . sat in drivers seat heard and felt a snap under drivers seat. broken weld on seat brace..0 person(s) were injured. 0 person(s) died.Mileage was 47500 miles. Vehicle Identification Number (VIN):JM1BL1S62A1. Mazda Mazda3 2010 problem was reported in LEEDS, MA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10667288

MAZDA MAZDA3 2010 car safety problem was reported on Dec 08, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . vehicle with continued issue with melting dashboard. requires very frequent cleaning of the inside of the windshield due to the substance build-up from the daily heating in the florida climate. during the day the glare from the sun reflects back onto the windshield causing it to be very difficult to see. polarized sunglasses seems to minimize the issue. at night, certain lighting also highlights the problems especially when sunglasses are not appropriate. on december 8th just after sundown a vehicle began to make a left turn into my right of way at an intersection. the star bursting from the windshield made it impossible to see that they were turning in from of me leading to an impact. i believe that this dashboard issue played a very significant issue contributing to this crash. the fault was obviously the other driver but due to the circumstances i was unable to react quickly..Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Mileage was 42000 miles. Vehicle Identification Number (VIN):JM1BL1S56A1. Mazda Mazda3 2010 problem was reported in LARGO, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Mazda Mazda3 2010 Unknown Or Other

Mazda Mazda3 2010 Unknown Or Other Review #10668521

MAZDA MAZDA3 2010 car safety problem was reported on Dec 27, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with UNKNOWN OR OTHER . there is a hairline crack in my 2010 mazda 3 dashboard. it is directly over the passenger side airbag and i feel this is a safety issue. i live in buffalo and the crack is worse in the winter. i spoke with mazda and said this would be expensive to repair, however, i have checked online and many other drivers of mazda's have had this issue. i would like to get this fixed, however, i am a graduate student and cannot afford this. i would like to make sure this is only cosmetic and not a safety concern..0 person(s) were injured. 0 person(s) died.Mileage was 55000 miles. Vehicle Identification Number (VIN):JM1BL1SG7A1. Mazda Mazda3 2010 problem was reported in AMHERST, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10668778

MAZDA MAZDA3 2010 car safety problem was reported on Aug 10, 2009.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . the dashboard of my mazda 3 is melted from the sun and causes glare on the windshield. it blocks vision of a portion of the road..0 person(s) were injured. 0 person(s) died.Mazda Mazda3 2010 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Mazda Mazda3 2010 Steering

Mazda Mazda3 2010 Steering Review #10669362

MAZDA MAZDA3 2010 car safety problem was reported on Dec 31, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STEERING . i was driving to work today and similar to the previous posts, my power steering light lit up and steering assist failed. 4 times in the 4 mile trip..0 person(s) were injured. 0 person(s) died.Mileage was 65000 miles. Mazda Mazda3 2010 problem was reported in DODGE CITY, KS. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10669511

MAZDA MAZDA3 2010 car safety problem was reported on Dec 30, 2014.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with SEATS . while driving, my front driver seat broke loose from the left rail. after inspecting the seat, i noticed it broke off the part that is welded to the rail. this could have easily caused an accident. i've already seen multiple other related incidents reported. i'm going to the mazda dealer tomorrow and see wheat they will do. ps. i'm 180 pounds, so it seems this seat was poorly welded..0 person(s) were injured. 0 person(s) died.Mileage was 51242 miles. Vehicle Identification Number (VIN):JM1BL1SF3A1. Mazda Mazda3 2010 problem was reported in TRUJILLO ALTO, PR. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 40 mph.

Mazda Mazda3 2010 Visibility/wiper

Mazda Mazda3 2010 Visibility/wiper Review #10670323

MAZDA MAZDA3 2010 car safety problem was reported on Jan 05, 2015.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with VISIBILITY/WIPER . after 3 years of normal commuter use, the dashboard in front of the driver seat has become excessively shiny. it is the top hump of the dashboard closest to the windshield. the shine reflects a glare onto the windshield directly in the driver's field of vision. the glare is sometimes so bad that it hinders the ability to see other vehicles directly in front of the car. the shine is unable to be wiped clean and leaves a sticky black residue when touched. it appears that the dashboard upholstery material and/or adhesive is defective. .0 person(s) were injured. 0 person(s) died.Mileage was 87900 miles. Vehicle Identification Number (VIN):JM1BL1S50A1. Mazda Mazda3 2010 problem was reported in MARGATE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Structure Body

Mazda Mazda3 2010 Structure Body Review #10670323

MAZDA MAZDA3 2010 car safety problem was reported on Jan 05, 2015.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with STRUCTURE:BODY . after 3 years of normal commuter use, the dashboard in front of the driver seat has become excessively shiny. it is the top hump of the dashboard closest to the windshield. the shine reflects a glare onto the windshield directly in the driver's field of vision. the glare is sometimes so bad that it hinders the ability to see other vehicles directly in front of the car. the shine is unable to be wiped clean and leaves a sticky black residue when touched. it appears that the dashboard upholstery material and/or adhesive is defective. .0 person(s) were injured. 0 person(s) died.Mileage was 87900 miles. Vehicle Identification Number (VIN):JM1BL1S50A1. Mazda Mazda3 2010 problem was reported in MARGATE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Mazda Mazda3 2010 Seats

Mazda Mazda3 2010 Seats Review #10672122

MAZDA MAZDA3 2010 car safety problem was reported on Jan 13, 2015.MAZDA MAZDA3 2010, manufactured by Mazda Motor Corp. had a problem with SEATS . sat down, heard a loud pop and seat move violently resulting in me falling away from steering wheel. upon inspection, left side weld on front rail snapped in half. .0 person(s) were injured. 0 person(s) died.Mileage was 61842 miles. Vehicle Identification Number (VIN):JM1BL1SGXA1. Mazda Mazda3 2010 problem was reported in UNION CITY, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Air Bags 5 Review(s)

Air Bags Frontal 1 Review(s)

Air Bags Frontal Sensor/control Module 1 Review(s)

Electrical System 9 Review(s)

Electrical System Battery 1 Review(s)

Electronic Stability Control 2 Review(s)

Engine 5 Review(s)

Engine And Engine Cooling 7 Review(s)

Engine And Engine Cooling Cooling System Radiator Assembly 1 Review(s)

Equipment Adaptive 1 Review(s)

Equipment Mechanical Jacks 1 Review(s)

Exterior Lighting 8 Review(s)

Fuel System, Gasoline 3 Review(s)

Latches/locks/linkages 3 Review(s)

Parking Brake 1 Review(s)

Power Train 17 Review(s)

Power Train Clutch Assembly 1 Review(s)

Power Train Driveline 1 Review(s)

Power Train Manual Transmission 5 Review(s)

Seat Belts 1 Review(s)

Seats 32 Review(s)

Service Brakes 3 Review(s)

Service Brakes, Hydraulic 4 Review(s)

Steering 16 Review(s)

Steering Electric Power Assist System 1 Review(s)

Structure 9 Review(s)

Structure Body 13 Review(s)

Suspension 3 Review(s)

Suspension Rear 1 Review(s)

Tires 22 Review(s)

Tires Pressure Monitoring And Regulating Systems 12 Review(s)

Tires Sidewall 1 Review(s)

Tires Valve 3 Review(s)

Unknown Or Other 72 Review(s)

Vehicle Speed Control 8 Review(s)

Visibility 2 Review(s)

Visibility/wiper 40 Review(s)

Visibility Defroster/defogger System 1 Review(s)

Visibility Rearview Mirrors/devices 1 Review(s)

Visibility Sun Roof Assembly 4 Review(s)

Wheels 32 Review(s)

Wheels Rim 1 Review(s)