Car-and-Safety.com
Mazda 626 1988 Safety Reports and Reviews
Mazda 626 1988 Reviews
Mazda 626 1988 Seat BeltsMazda 626 1988 Seat Belts Review #960052 MAZDA 626 1988 car safety problem was reported on Feb 15, 1995.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . motorized safety belt is stuck in position. this has happen after the recall work was performed. tt.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2425J1. Mazda 626 1988 problem was reported in SELDEN, NY. Vehicle was not using Cruise Control. Mazda 626 1988 Seat Belts Review #481012 MAZDA 626 1988 car safety problem was reported on Feb 05, 1995.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . driver's side motor belt fails to release/move forward when vehicle is shut off. *ak.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2223J1. Mazda 626 1988 problem was reported in SCOTTSDALE, AZ. Vehicle was not using Cruise Control. Mazda 626 1988 Service Brakes, Hydraulic Foundation Components Disc PadsMazda 626 1988 Service Brakes, Hydraulic Foundation Components Disc Pads Review #481012 MAZDA 626 1988 car safety problem was reported on Feb 05, 1995.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:PADS . replaced front brake pads 3 times, also replaced rear brake shoes..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2223J1. Mazda 626 1988 problem was reported in SCOTTSDALE, AZ. Vehicle was not using Cruise Control. Mazda 626 1988 Latches/locks/linkages Doors LatchMazda 626 1988 Latches/locks/linkages Doors Latch Review #481012 MAZDA 626 1988 car safety problem was reported on Feb 05, 1995.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with LATCHES/LOCKS/LINKAGES:DOORS:LATCH . inner/outer door latches failed. *ak.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2223J1. Mazda 626 1988 problem was reported in SCOTTSDALE, AZ. Vehicle was not using Cruise Control. Mazda 626 1988 Seat BeltsMazda 626 1988 Seat Belts Review #961987 MAZDA 626 1988 car safety problem was reported on .MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . left drivers door automatic seat belts is inoperative. tt.0 person(s) were injured. 0 person(s) died.Mazda 626 1988 problem was reported in E. WINDSOR, NJ. Vehicle was not using Cruise Control. Mazda 626 1988 Electrical System Fuses And Circuit BreakersMazda 626 1988 Electrical System Fuses And Circuit Breakers Review #962143 MAZDA 626 1988 car safety problem was reported on .MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with ELECTRICAL SYSTEM:FUSES AND CIRCUIT BREAKERS . when turning the wheel to the right the power window fuse blows ignition switch may be the cause, and 86'and 87' report the same problem. tt.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2244J1. Mazda 626 1988 problem was reported in LINDEN, NJ. Vehicle was not using Cruise Control. Mazda 626 1988 Seat Belts Front Buckle AssemblyMazda 626 1988 Seat Belts Front Buckle Assembly Review #962552 MAZDA 626 1988 car safety problem was reported on Apr 01, 1994.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS:FRONT:BUCKLE ASSEMBLY . problem with seat belts sticking and sometimes not latching. tt.0 person(s) were injured. 0 person(s) died.Mazda 626 1988 problem was reported in PLEASANT GRO, AL. Vehicle was not using Cruise Control. Mazda 626 1988 Seat Belts Review #963821 MAZDA 626 1988 car safety problem was reported on Feb 01, 1994.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . drivers motorized seat belt is jammed and belt does not move. tt.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2425J1. Mazda 626 1988 problem was reported in NEW SMYRNA B, FL. Vehicle was not using Cruise Control. Mazda 626 1988 Structure Body DoorMazda 626 1988 Structure Body Door Review #964334 MAZDA 626 1988 car safety problem was reported on Apr 10, 1994.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with STRUCTURE:BODY:DOOR . door would fly open when window is rolled down mazda offers no assistance. tt.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2427J1. Mazda 626 1988 problem was reported in ATHEN, AL. Vehicle was not using Cruise Control. Mazda 626 1988 Seat BeltsMazda 626 1988 Seat Belts Review #964886 MAZDA 626 1988 car safety problem was reported on Apr 18, 1995.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . faulkner mazda 88v063. recall was not performed correctly. dealership want to charge for completion of campaign. tt.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2226J1. Mazda 626 1988 problem was reported in PHILADELPHIA, PA. Vehicle was not using Cruise Control. Mazda 626 1988 Seat Belts Review #965095 MAZDA 626 1988 car safety problem was reported on May 10, 1995.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . takata motorized seat belt passenger side, won't go up or down, must operate manually. tt.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2224J1. Mazda 626 1988 problem was reported in LOLO, MT. Vehicle was not using Cruise Control. Mazda 626 1988 Seat Belts Front RetractorMazda 626 1988 Seat Belts Front Retractor Review #967313 MAZDA 626 1988 car safety problem was reported on Jan 01, 1995.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS:FRONT:RETRACTOR . the front driver and passenger seatbelts the inertia reel works only rarely. please explain. tt.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2223J1. Mazda 626 1988 problem was reported in LAKEWOOD, CO. Vehicle was not using Cruise Control. Mazda 626 1988 Seat Belts Review #971151 MAZDA 626 1988 car safety problem was reported on .MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . vehicles seat belt motorized retractor is inoperative on driver side. tt.0 person(s) were injured. 0 person(s) died.Mazda 626 1988 problem was reported in ARCADIA, FL. Vehicle was not using Cruise Control. Mazda 626 1988 Structure Body DoorMazda 626 1988 Structure Body Door Review #485110 MAZDA 626 1988 car safety problem was reported on June 13, 1995.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with STRUCTURE:BODY:DOOR . outside door handle failed prior to recall (93v-174). *ak.0 person(s) were injured. 0 person(s) died.Mazda 626 1988 problem was reported in WINCHESTER, MA. Vehicle was not using Cruise Control. Mazda 626 1988 Power Train Automatic TransmissionMazda 626 1988 Power Train Automatic Transmission Review #475011 MAZDA 626 1988 car safety problem was reported on Oct 19, 1994.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . transmission failure..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2224J1. Mazda 626 1988 problem was reported in HAMMOND, IN. Vehicle was not using Cruise Control. Mazda 626 1988 Power Train Review #475011 MAZDA 626 1988 car safety problem was reported on Oct 19, 1994.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with POWER TRAIN . speedometer cable severed. *tw.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2224J1. Mazda 626 1988 problem was reported in HAMMOND, IN. Vehicle was not using Cruise Control. Mazda 626 1988 Seat BeltsMazda 626 1988 Seat Belts Review #974482 MAZDA 626 1988 car safety problem was reported on Oct 31, 1995.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . driver's side automatic shoulder belt has broken, needs replacement. tt the ribbon spring broke causing the belt to remain in the forward position. *yh.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2220J1. Mazda 626 1988 problem was reported in HURON, OH. Original Owner. Vehicle was using Cruise Control.Mazda 626 1988 drive type:FWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. Mazda 626 1988 TRANSMISSION TYPE: MAN . Mazda 626 1988 Fuel System, Gasoline Storage Tank AssemblyMazda 626 1988 Fuel System, Gasoline Storage Tank Assembly Review #974504 MAZDA 626 1988 car safety problem was reported on Oct 11, 1995.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY . they would not order the part when they were supposed to and then when they did get the part they would not fix the car. please describe. tt.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2223J1. Mazda 626 1988 problem was reported in NORMAN, OK. Vehicle was not using Cruise Control. Mazda 626 1988 Seat BeltsMazda 626 1988 Seat Belts Review #975806 MAZDA 626 1988 car safety problem was reported on Oct 07, 1995.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . shoulder belt is still not working properly. recall # 31805. please describe. tt.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2229J1. Mazda 626 1988 problem was reported in TORRANCE, CA. Vehicle was not using Cruise Control. Mazda 626 1988 Seat Belts Front RetractorMazda 626 1988 Seat Belts Front Retractor Review #976899 MAZDA 626 1988 car safety problem was reported on .MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS:FRONT:RETRACTOR . the driver seat belt retractor is not working right . tt.0 person(s) were injured. 0 person(s) died.Mazda 626 1988 problem was reported in MADISON, CT. Vehicle was not using Cruise Control. Mazda 626 1988 Seat Belts Review #982993 MAZDA 626 1988 car safety problem was reported on .MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . had recall work done on motorized seat belts, they still malfunction. *ak.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2225J1. Mazda 626 1988 problem was reported in TERRE HAUTE, IN. Vehicle was not using Cruise Control. Mazda 626 1988 Seat Belts Review #982993 MAZDA 626 1988 car safety problem was reported on .MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . had recall work done on motorized seat belts, they still malfunction. *ak.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2225J1. Mazda 626 1988 problem was reported in TERRE HAUTE, IN. Vehicle was not using Cruise Control. Mazda 626 1988 Seat Belts Review #983783 MAZDA 626 1988 car safety problem was reported on Apr 01, 1996.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . recall related, 88v063000, contacted dealership 2/1/95, went in on 3/1/96 wrong parts went in again never received parts 88vo63000. *ak.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2222J1. Mazda 626 1988 problem was reported in BRONX, NY. Vehicle was not using Cruise Control. Mazda 626 1988 Seat Belts Review #983783 MAZDA 626 1988 car safety problem was reported on Apr 01, 1996.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . recall related, 88v063000, contacted dealership 2/1/95, went in on 3/1/96 wrong parts went in again never received parts 88vo63000. *ak.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2222J1. Mazda 626 1988 problem was reported in BRONX, NY. Vehicle was not using Cruise Control. Mazda 626 1988 Seat Belts Review #504487 MAZDA 626 1988 car safety problem was reported on Oct 01, 1993.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . motorized seat belts retract without warning while car is in motion. *ak.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2247J1. Mazda 626 1988 problem was reported in COLORADO SPR, CO. Vehicle was not using Cruise Control. Mazda 626 1988 Visibility Power Window Devices And ControlsMazda 626 1988 Visibility Power Window Devices And Controls Review #500836 MAZDA 626 1988 car safety problem was reported on Jan 15, 1996.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with VISIBILITY:POWER WINDOW DEVICES AND CONTROLS . rear window motor failed. *sd.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2225J1. Mazda 626 1988 problem was reported in WINCHESTER, VA. Vehicle was not using Cruise Control. Mazda 626 1988 Structure Body DoorMazda 626 1988 Structure Body Door Review #500836 MAZDA 626 1988 car safety problem was reported on Sept 01, 1993.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with STRUCTURE:BODY:DOOR . front left door fails to open, repaired prior to recall. *sd.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2225J1. Mazda 626 1988 problem was reported in WINCHESTER, VA. Vehicle was not using Cruise Control. Mazda 626 1988 Fuel System, Gasoline Storage Tank AssemblyMazda 626 1988 Fuel System, Gasoline Storage Tank Assembly Review #505427 MAZDA 626 1988 car safety problem was reported on Mar 05, 1996.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY . fuel tank split at weld, causing gasoline leak. *sd.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2222J1. Mazda 626 1988 problem was reported in ORION, MI. Vehicle was not using Cruise Control. Mazda 626 1988 Seat BeltsMazda 626 1988 Seat Belts Review #800381 MAZDA 626 1988 car safety problem was reported on Jan 12, 1996.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . no parts since october 1995. (no other information on form) *slc.Vehicle Identification Number (VIN):JM1GD2226J1. Mazda 626 1988 problem was reported in MARTINS, SC. Vehicle was purchased on Oct 01, 1992. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Mazda 626 1988 drive type:FWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. Mazda 626 1988 TRANSMISSION TYPE: AUTO. Mazda 626 1988 Visibility WindshieldMazda 626 1988 Visibility Windshield Review #8000852 MAZDA 626 1988 car safety problem was reported on Aug 14, 1996.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with VISIBILITY:WINDSHIELD . failure on the driver side door, the driver side door will not open from the outside.*ak.Vehicle Identification Number (VIN):JM1GD2220J1. Mazda 626 1988 problem was reported in LEON VALLEY, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Mazda 626 1988 Latches/locks/linkages Doors LatchMazda 626 1988 Latches/locks/linkages Doors Latch Review #8000852 MAZDA 626 1988 car safety problem was reported on Aug 14, 1996.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with LATCHES/LOCKS/LINKAGES:DOORS:LATCH . failure on the driver side door, the driver side door will not open from the outside.*ak.Vehicle Identification Number (VIN):JM1GD2220J1. Mazda 626 1988 problem was reported in LEON VALLEY, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Mazda 626 1988 Seat Belts Front RetractorMazda 626 1988 Seat Belts Front Retractor Review #804473 MAZDA 626 1988 car safety problem was reported on .MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS:FRONT:RETRACTOR . the passenger's side seat belt retractor stopped working . please describe . *ak.Vehicle Identification Number (VIN):JM1GD242XJ1. Mazda 626 1988 problem was reported in FORT WAYNE, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Mazda 626 1988 Power Train Automatic TransmissionMazda 626 1988 Power Train Automatic Transmission Review #522583 MAZDA 626 1988 car safety problem was reported on Mar 01, 1995.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . automatic transmission jumps out of gear..Vehicle Identification Number (VIN):JM1GD2223J1. Mazda 626 1988 problem was reported in TUCSON, AZ. Vehicle was purchased on Mar 15, 1995. Vehicle was using Cruise Control.Mazda 626 1988 drive type:FWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 5 mph. Mazda 626 1988 Seat BeltsMazda 626 1988 Seat Belts Review #819573 MAZDA 626 1988 car safety problem was reported on Nov 25, 1997.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . the driver's side automatic shoulder belt is inoperative due to the belt not staying in the correct position, . consumer has contacted the dealer, dealer has replaced parts. *ak.Vehicle Identification Number (VIN):JM1GD244XJ1. Mazda 626 1988 problem was reported in FISHERS, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Mazda 626 1988 Engine And Engine Cooling Exhaust System Manifold/header/muffler/tail PipeMAZDA 626 1988 car safety problem was reported on Apr 01, 1998.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE . bolts overheat and fall of engine manifold, causing a leak of carbon monoxide in the passenger's compartment..Mazda 626 1988 problem was reported in YORK, PA. Original Owner. Vehicle was purchased on Feb 14, 1989. Vehicle was using Cruise Control.Mazda 626 1988 drive type:FWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. Mazda 626 1988 Structure Body DoorMazda 626 1988 Structure Body Door Review #521555 MAZDA 626 1988 car safety problem was reported on .MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with STRUCTURE:BODY:DOOR . vehicle in for recall work on door, however incomplete when delivered..Mazda 626 1988 problem was reported in LYNN HAVEN, FL. Vehicle was not using Cruise Control. Mazda 626 1988 Electrical System Wiring Front UnderhoodMazda 626 1988 Electrical System Wiring Front Underhood Review #700465 MAZDA 626 1988 car safety problem was reported on Nov 01, 1998.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with ELECTRICAL SYSTEM:WIRING:FRONT UNDERHOOD . fire started under hood. possibly around fuel filter and/or wiring harness area. resulted in severe fire that totaled the vehicle..Vehicle was on fire. 0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2226J1. Mazda 626 1988 problem was reported in FRANKLIN, NH. Accident was reported to Police. Vehicle was purchased on Oct 01, 1998. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Mazda 626 1988 drive type:FWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph. Mazda 626 1988 Seat Belts Front WebbingMazda 626 1988 Seat Belts Front Webbing Review #604289 MAZDA 626 1988 car safety problem was reported on .MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS:FRONT:WEBBING . seat belt shoulder harness failed..Vehicle Identification Number (VIN):JM1GD244XJ1. Mazda 626 1988 problem was reported in CHICAGO, IL. Original Owner. Vehicle was purchased on July 01, 1988. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Mazda 626 1988 drive type:FWD. FUEL SYSTEM:N/A. Mazda 626 1988 TRANSMISSION TYPE: MAN . Mazda 626 1988 Power Train Automatic TransmissionMazda 626 1988 Power Train Automatic Transmission Review #835654 MAZDA 626 1988 car safety problem was reported on Mar 02, 1998.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . when driving at any speed transmission is slipping, and there is some noise coming from vehicle. consumer brought vehicle into the repair shop. after being repaired, the noise came back.dealer can't determine the problem. *ak.Mazda 626 1988 problem was reported in KINGWOOD, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Mazda 626 1988 TRANSMISSION TYPE: AUTO. Mazda 626 1988 SuspensionMazda 626 1988 Suspension Review #835654 MAZDA 626 1988 car safety problem was reported on Mar 02, 1998.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SUSPENSION . when driving at any speed transmission is slipping, and there is some noise coming from vehicle. consumer brought vehicle into the repair shop. after being repaired, the noise came back.dealer can't determine the problem. *ak.Mazda 626 1988 problem was reported in KINGWOOD, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Mazda 626 1988 TRANSMISSION TYPE: AUTO. Mazda 626 1988 Seat BeltsMazda 626 1988 Seat Belts Review #782362 MAZDA 626 1988 car safety problem was reported on .MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . left front motorized seat belt failed. yh .Vehicle Identification Number (VIN):JM1GD222XJ1. Mazda 626 1988 problem was reported in SHAWNEE, KS. Original Owner. Vehicle was purchased on Oct 01, 1988. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Mazda 626 1988 drive type:FWD. Mazda 626 1988 Latches/locks/linkages Doors LatchMazda 626 1988 Latches/locks/linkages Doors Latch Review #782363 MAZDA 626 1988 car safety problem was reported on May 17, 1999.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with LATCHES/LOCKS/LINKAGES:DOORS:LATCH . drivers side door latch failed. yh .Vehicle Identification Number (VIN):JM1GD222XJ1. Mazda 626 1988 problem was reported in SHAWNEE, KS. Original Owner. Vehicle was purchased on Oct 01, 1988. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Mazda 626 1988 drive type:FWD. Mazda 626 1988 Seat Belts Front AnchorageMazda 626 1988 Seat Belts Front Anchorage Review #707963 MAZDA 626 1988 car safety problem was reported on June 30, 1998.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS:FRONT:ANCHORAGE . whenever the door is opened and the sunvisor has not been returned to its locked position the automatic seatbelt catches on the visor and breaks it while retracting. i have broken three and would have broken more if i had not disconnected the automatic seatbelt. i consider this remedy to be unacceptable..0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2229J1. Mazda 626 1988 problem was reported in SUGAR LAND, TX. Original Owner. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Mazda 626 1988 drive type:FWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph. Mazda 626 1988 Seat Belts Front RetractorMazda 626 1988 Seat Belts Front Retractor Review #842026 MAZDA 626 1988 car safety problem was reported on Apr 12, 1998.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS:FRONT:RETRACTOR . shoulder belts on driver's side/passenger's side retract intermittently. sometimes consumer has to put his hand out of the window to get the shoulder belt to work. dealer can't determine cause of the problem. *ak.Vehicle Identification Number (VIN):JM1GD2249J1. Mazda 626 1988 problem was reported in KERNERSVILLE, NC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Mazda 626 1988 drive type:FWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. Mazda 626 1988 TRANSMISSION TYPE: AUTO. Mazda 626 1988 Electrical System Battery CablesMazda 626 1988 Electrical System Battery Cables Review #844505 MAZDA 626 1988 car safety problem was reported on June 20, 1999.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with ELECTRICAL SYSTEM:BATTERY:CABLES . just parked vehicle & left. neighbors knocked on door to inform owner vehicle was on fire. fire department called & put flames out. was informed the battery was cause of fire. there was no prior warning. *ak *ml.Vehicle was on fire. Vehicle Identification Number (VIN):JM1GD2243J1. Mazda 626 1988 problem was reported in RALEIGH, NC. Vehicle was purchased on June 14, 1999. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Mazda 626 1988 drive type:FWD. FUEL SYSTEM:N/A. Mazda 626 1988 TRANSMISSION TYPE: AUTO. Mazda 626 1988 Latches/locks/linkages Doors LatchMazda 626 1988 Latches/locks/linkages Doors Latch Review #709964 MAZDA 626 1988 car safety problem was reported on July 01, 1999.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with LATCHES/LOCKS/LINKAGES:DOORS:LATCH . front door locks repaired under recall several years ago -- now drivers' side door lock has failed in exactly the manner described in recall notice -- lowering drivers' window caused door to unlatch and fly open!.Vehicle Identification Number (VIN):JM1GD2228J1. Mazda 626 1988 problem was reported in HAMPSTEAD, NH. Original Owner. Vehicle was purchased on Aug 01, 1988. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Mazda 626 1988 drive type:FWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. Mazda 626 1988 Seat BeltsMazda 626 1988 Seat Belts Review #847184 MAZDA 626 1988 car safety problem was reported on Jan 01, 1996.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . automatic shoulder belt is broke, and consumer can't get out of the seat belt. *ak.Mazda 626 1988 problem was reported in LOCUST GROVE, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Mazda 626 1988 Power Train Axle AssemblyMazda 626 1988 Power Train Axle Assembly Review #714769 MAZDA 626 1988 car safety problem was reported on Nov 13, 1999.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with POWER TRAIN:AXLE ASSEMBLY . front axle of car rusted completel,y and broke apart while driving. *ak( dot number: ).Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2223J1. Mazda 626 1988 problem was reported in FARMINGTON HILLS, MI. Original Owner. Vehicle was purchased on Feb 01, 1988. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Mazda 626 1988 drive type:RWD. FUEL TYPE: GAS. VEHICLE SPEED: 60 mph. Mazda 626 1988 Latches/locks/linkages Doors LatchMazda 626 1988 Latches/locks/linkages Doors Latch Review #714788 MAZDA 626 1988 car safety problem was reported on Oct 29, 1999.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with LATCHES/LOCKS/LINKAGES:DOORS:LATCH . passenger door not able to be opened from inside or outside. *ak.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):JM1GD2229J1. Mazda 626 1988 problem was reported in WARREN, MI. Original Owner. Vehicle was purchased on Jan 01, 1989. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Mazda 626 1988 drive type:FWD. FUEL TYPE: GAS. Mazda 626 1988 Seat BeltsMazda 626 1988 Seat Belts Review #723128 MAZDA 626 1988 car safety problem was reported on June 01, 1998.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . automatic motorized shoulder restraints fail to complete cycle upon engine start-up choking passenger. upon opening door at stop, restraints fail to disengage trapping occupant until manually disconnected . recall at dealer failed to yield vin match. also told vehicle too old to repair. problem exists anyway, due to same manufacturer defect as in campaign 88v06300. can cause injury to ocucpants. *ak.Vehicle Identification Number (VIN):JM1GD2228J1. Mazda 626 1988 problem was reported in WARE, MA. Vehicle was purchased on Aug 01, 1990. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Mazda 626 1988 drive type:FWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph. Mazda 626 1988 Seat Belts Review #899894 MAZDA 626 1988 car safety problem was reported on Dec 05, 2001.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with SEAT BELTS . recall 88 v 063 000/passive restraint belt: both driver'sand passenger's motor belts failed to operate. dealer was contacted, and informed consumer that this vehicle was not covered under therecall due to vin. feel free to provide any further information concerning this matter.*ak.Vehicle Identification Number (VIN):JM1GD2227J1. Mazda 626 1988 problem was reported in NEW YORK, NY. Original Owner. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Mazda 626 1988 Fuel System, Gasoline DeliveryMazda 626 1988 Fuel System, Gasoline Delivery Review #8010516 MAZDA 626 1988 car safety problem was reported on Mar 26, 2002.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with FUEL SYSTEM, GASOLINE:DELIVERY . while driving the front of vehicle caught on fire due to fuel lines. *ak consumer states that the fire progressed to the rear underside from center third of underside, the passenger was injured when being escorted out of the vehicle. *slc.Vehicle was on fire. 1 person(s) were injured. Vehicle Identification Number (VIN):JM1GD2225J1. Mazda 626 1988 problem was reported in VIOLA, DE. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Mazda 626 1988 drive type:FWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. Mazda 626 1988 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 65 mph. Mazda 626 1988 Engine And Engine Cooling Exhaust System Manifold/header/muffler/tail PipeMAZDA 626 1988 car safety problem was reported on Jan 07, 2003.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE . defective tailpipe caused carbon monoxide to enter vehicle's interior cabin resulting in consumer contracting carbon monoxide poisoning. dealer diagnosed several holes along top of tailpipe between the catalytic converter and the muffler. ph top seam of exhaust pipe had rotten out between catalytic converter and muffler. *tt.Vehicle Identification Number (VIN):JM1GD2225J1. Mazda 626 1988 problem was reported in CHEROKEE VILLAGE, AR. Original Owner. Vehicle was purchased on Aug 15, 1988. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 4 CYLINDERS. FUEL TYPE: GAS. Mazda 626 1988 TRANSMISSION TYPE: AUTO. DEALER'S NAME: MCGRATH PONTIAC . DEALER'S CITY: CEDAR RAPIDS . DEALER'S STATE CODE: IA. Mazda 626 1988 Engine And Engine Cooling Exhaust System Emission Control Gas Recirculation Valve (egr Valve)MAZDA 626 1988 car safety problem was reported on June 25, 2005.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE) . 1. bought a 1998 mazda 626 lx. 2. at 56000 miles, engine needed a new header. 3. at 57000 miles, starter motor failed. 3. at 60000 miles, transmission failed. 4. currently at 70000 miles, need new exhaust system .Mileage was 50000 miles. Vehicle Identification Number (VIN):1YVGF22C2W5. Mazda 626 1988 problem was reported in FLUSHING, NY. Vehicle was purchased on Apr 14, 2003. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda 626 1988 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Mazda 626 1988 TRANSMISSION TYPE: AUTO. Mazda 626 1988 Communications Back Up AlarmMazda 626 1988 Communications Back Up Alarm Review #10127374 MAZDA 626 1988 car safety problem was reported on June 25, 2005.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with COMMUNICATIONS:BACK UP ALARM . 1. bought a 1998 mazda 626 lx. 2. at 56000 miles, engine needed a new header. 3. at 57000 miles, starter motor failed. 3. at 60000 miles, transmission failed. 4. currently at 70000 miles, need new exhaust system .Mileage was 50000 miles. Vehicle Identification Number (VIN):1YVGF22C2W5. Mazda 626 1988 problem was reported in FLUSHING, NY. Vehicle was purchased on Apr 14, 2003. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda 626 1988 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Mazda 626 1988 TRANSMISSION TYPE: AUTO. Mazda 626 1988 Communications Horn AssemblyMazda 626 1988 Communications Horn Assembly Review #10127374 MAZDA 626 1988 car safety problem was reported on June 25, 2005.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with COMMUNICATIONS:HORN ASSEMBLY . 1. bought a 1998 mazda 626 lx. 2. at 56000 miles, engine needed a new header. 3. at 57000 miles, starter motor failed. 3. at 60000 miles, transmission failed. 4. currently at 70000 miles, need new exhaust system .Mileage was 50000 miles. Vehicle Identification Number (VIN):1YVGF22C2W5. Mazda 626 1988 problem was reported in FLUSHING, NY. Vehicle was purchased on Apr 14, 2003. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda 626 1988 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Mazda 626 1988 TRANSMISSION TYPE: AUTO. Mazda 626 1988 Electrical SystemMazda 626 1988 Electrical System Review #10127374 MAZDA 626 1988 car safety problem was reported on June 25, 2005.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with ELECTRICAL SYSTEM . 1. bought a 1998 mazda 626 lx. 2. at 56000 miles, engine needed a new header. 3. at 57000 miles, starter motor failed. 3. at 60000 miles, transmission failed. 4. currently at 70000 miles, need new exhaust system .Mileage was 50000 miles. Vehicle Identification Number (VIN):1YVGF22C2W5. Mazda 626 1988 problem was reported in FLUSHING, NY. Vehicle was purchased on Apr 14, 2003. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda 626 1988 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Mazda 626 1988 TRANSMISSION TYPE: AUTO. Mazda 626 1988 Electrical System Ignition Anti-theft ControllerMazda 626 1988 Electrical System Ignition Anti-theft Controller Review #10127374 MAZDA 626 1988 car safety problem was reported on June 25, 2005.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with ELECTRICAL SYSTEM:IGNITION:ANTI-THEFT CONTROLLER . 1. bought a 1998 mazda 626 lx. 2. at 56000 miles, engine needed a new header. 3. at 57000 miles, starter motor failed. 3. at 60000 miles, transmission failed. 4. currently at 70000 miles, need new exhaust system .Mileage was 50000 miles. Vehicle Identification Number (VIN):1YVGF22C2W5. Mazda 626 1988 problem was reported in FLUSHING, NY. Vehicle was purchased on Apr 14, 2003. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda 626 1988 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Mazda 626 1988 TRANSMISSION TYPE: AUTO. Mazda 626 1988 Power Train Automatic TransmissionMazda 626 1988 Power Train Automatic Transmission Review #10127374 MAZDA 626 1988 car safety problem was reported on June 25, 2005.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION . 1. bought a 1998 mazda 626 lx. 2. at 56000 miles, engine needed a new header. 3. at 57000 miles, starter motor failed. 3. at 60000 miles, transmission failed. 4. currently at 70000 miles, need new exhaust system .Mileage was 50000 miles. Vehicle Identification Number (VIN):1YVGF22C2W5. Mazda 626 1988 problem was reported in FLUSHING, NY. Vehicle was purchased on Apr 14, 2003. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda 626 1988 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Mazda 626 1988 TRANSMISSION TYPE: AUTO. Mazda 626 1988 Electrical System Alternator/generator/regulatorMazda 626 1988 Electrical System Alternator/generator/regulator Review #10127374 MAZDA 626 1988 car safety problem was reported on June 25, 2005.MAZDA 626 1988, manufactured by MAZDA NORTH AMERICAN OPERATIONS had a problem with ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR . 1. bought a 1998 mazda 626 lx. 2. at 56000 miles, engine needed a new header. 3. at 57000 miles, starter motor failed. 3. at 60000 miles, transmission failed. 4. currently at 70000 miles, need new exhaust system .Mileage was 50000 miles. Vehicle Identification Number (VIN):1YVGF22C2W5. Mazda 626 1988 problem was reported in FLUSHING, NY. Vehicle was purchased on Apr 14, 2003. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 4 CYLINDERS. Mazda 626 1988 drive type:FWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Mazda 626 1988 TRANSMISSION TYPE: AUTO. |
-
Mazda 626 1988 Forum
Discuss and Report Mazda 626 Problems -
Service Bulletins
View Recent Mazda 626 1988 repair guidance -
Recalls
Latest recall and safety Mazda 626 1988 information
Mazda 626 1988 Systems
Search 1000s of Car Reviews, Recalls and Technical Bulletins
Start by entering a car model, system, manufacturer or any combination of keywords.
Mazda 626 1988 Reports
My 2001 626 transmission slips slightly when first put it into drive from park then bucks. After it engages it shifts fine I have a 1998 Mazda Protege LX Touring Edition (4dr) and need to install a rear-facing infant car seat (with base) in the back seat, preferably center position. Because I purchased my Mazda used, I do not have the Owner's Manual. I was told th question is whiseling noise when take off Sorry the question is for Tribute 2010 for whiseling noise when taking off Today I backed up in a narrow parking lot and as I put my 2009 Mazda 6 in drive and with my foot still on the brake the car accelrated unexpectedly over about 10 feet and into a building, the engine revving and smoking as I put it in neutral and t mazda3 2007 radio fuse location my alt light came on and stayed so i disconnected the battery to see if the car would sat running and now both headlaights burnt out the tach is in op no and the air bag lamp stays on all the time what happened? 94 mazda 626 air bag ligt stays on after alt burnt out what is the problem I REALLY THINK I HAVE THE ANSWER, I HOPE. I have an 2002 Mazda tribute it stalls especially in hot weather. The manual says very little, but it said it may be a vapor lock. My car was parked inside a humid garage so when it stalls on me seas Another really difficult thing to diagnose was the engine light, and warning bell sounding off for a yr. the dealer ship misdiagnosed the problem. Charged me for a diagnostic test they did not do. They sold me a battery, and sent me down the r I can't find my Satellitte Radio Number, it appeared originally on my NAV Screen when I would depress the SAT button. It no longer appears. I don't know if that's a malfunction. i have a 2002 millenia , would a 1998 automtic transmission work for car, denny.koch@insightbb.com
I have a 2008 Mazda CX-9 Grand touring with the Navigation touch s