Car-and-Safety.com
Ford Crown Victoria 2011 Safety Reports and Reviews
Ford Crown Victoria 2011 Reviews
Ford Crown Victoria 2011 SeatsFord Crown Victoria 2011 Seats Review #10400349 FORD CROWN VICTORIA 2011 car safety problem was reported on May 02, 2011.FORD CROWN VICTORIA 2011, manufactured by FORD MOTOR COMPANY had a problem with SEATS . rental 2011 ford crown victoria. consumer writes in regards to vehicle seating *tgw the consumer stated none of the seats had any lumbar support, there was no leg room and there was also inadequate headrest support in case of an accident. *jb.Ford Crown Victoria 2011 problem was reported in FAIRLAWN, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Ford Crown Victoria 2011 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Crown Victoria 2011 TRANSMISSION TYPE: AUTO. Ford Crown Victoria 2011 Seats Review #10454798 FORD CROWN VICTORIA 2011 car safety problem was reported on Mar 05, 2012.FORD CROWN VICTORIA 2011, manufactured by FORD MOTOR COMPANY had a problem with SEATS . i am a detective with the belleville police department, nj. we are having an ongoing problem with the ford crown victoria 2011 police intertceptor with manual seats. all our officers are reporting lower back pain due to a lower back bolster built in as part of the seat. this bolster is not adjustable. upon bringing this problem to our local fleet dealer, we were advised that it was the design of the seat, and that even if we wanted to replace these seats with the six way power seat for the same year we were advised that ford and our insurance carrier would not allow it due to safety reasons. we have reached out to other police departments if they are having the same problem with these seats, and i am currently building a database of other departments. please contact our department to be included. thank you. *tr.Mileage was 223 miles. Ford Crown Victoria 2011 problem was reported in BELLEVILLE, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Ford Crown Victoria 2011 Seats Review #10462258 FORD CROWN VICTORIA 2011 car safety problem was reported on June 19, 2012.FORD CROWN VICTORIA 2011, manufactured by FORD MOTOR COMPANY had a problem with SEATS . the headrests on the 2011 ford crown victoria are causing the officers to have neck problems. the headrest is so large and does not adjust forward and backward, it is pushing their heads forward and down, as you know they spend at least 8 hours in their vehicles each shift. since we have purchased the 2011 crown vics we have had nothing but complaints. it is very uncomfortable and unsafe for the officers to be driving under these conditions. *js.0 person(s) were injured. 0 person(s) died.Mileage was 12 miles. Vehicle Identification Number (VIN):2FABP7BV3BX. Ford Crown Victoria 2011 problem was reported in SIMI VALLEY, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. Ford Crown Victoria 2011 drive type:RWD. FUEL TYPE: BIFUEL. VEHICLE SPEED: 0 mph. Ford Crown Victoria 2011 Seats Review #10466919 FORD CROWN VICTORIA 2011 car safety problem was reported on May 01, 2012.FORD CROWN VICTORIA 2011, manufactured by FORD MOTOR COMPANY had a problem with SEATS . my police department issued me a 2011 ford crown victoria around september of 2011. ever since, i have spent countless hours adjusting the seat in an attempt to keep my mid-lower back from hurting. i learned that there is a metal bar installed in the seat causing the issues. once the bar is adjusted, the seats aren't as bad. i also have had a great amount of trouble with neck pain. i have since had to see a doctor about this. the head rests that are in the vehicle are causing my head to be pushed forward and straining the muscles in my neck. i'm shocked to learn that this hasn't already been a recall for ford. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 12000 miles. Vehicle Identification Number (VIN):2FABP7BV8BX. Ford Crown Victoria 2011 problem was reported in BROWNSBORO, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 0 mph. Ford Crown Victoria 2011 SteeringFord Crown Victoria 2011 Steering Review #10476620 FORD CROWN VICTORIA 2011 car safety problem was reported on Sept 18, 2012.FORD CROWN VICTORIA 2011, manufactured by Ford Motor Company had a problem with STEERING . inspection found lower bushing of steering column dislodged and shaft working out of spline. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 54000 miles. Vehicle Identification Number (VIN):2FABP7BV6BX. Ford Crown Victoria 2011 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph. Ford Crown Victoria 2011 Steering Review #10476621 FORD CROWN VICTORIA 2011 car safety problem was reported on Sept 19, 2012.FORD CROWN VICTORIA 2011, manufactured by Ford Motor Company had a problem with STEERING . inspection found the lower column bushing dislodged from tube and shaft working out of spline. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 77000 miles. Vehicle Identification Number (VIN):2FABP7BV5BX. Ford Crown Victoria 2011 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 0 mph. Ford Crown Victoria 2011 Steering Review #10478028 FORD CROWN VICTORIA 2011 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2011, manufactured by Ford Motor Company had a problem with STEERING . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 25200 miles. Vehicle Identification Number (VIN):2FABP7BV5BX. Ford Crown Victoria 2011 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 0 mph. Ford Crown Victoria 2011 SuspensionFord Crown Victoria 2011 Suspension Review #10478028 FORD CROWN VICTORIA 2011 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2011, manufactured by Ford Motor Company had a problem with SUSPENSION . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 25200 miles. Vehicle Identification Number (VIN):2FABP7BV5BX. Ford Crown Victoria 2011 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 0 mph. Ford Crown Victoria 2011 SteeringFord Crown Victoria 2011 Steering Review #10478033 FORD CROWN VICTORIA 2011 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2011, manufactured by Ford Motor Company had a problem with STEERING . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 14222 miles. Vehicle Identification Number (VIN):2FABP7BV5BX. Ford Crown Victoria 2011 problem was reported in HERRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 0 mph. Ford Crown Victoria 2011 SuspensionFord Crown Victoria 2011 Suspension Review #10478033 FORD CROWN VICTORIA 2011 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2011, manufactured by Ford Motor Company had a problem with SUSPENSION . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 14222 miles. Vehicle Identification Number (VIN):2FABP7BV5BX. Ford Crown Victoria 2011 problem was reported in HERRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 0 mph. Ford Crown Victoria 2011 SteeringFord Crown Victoria 2011 Steering Review #10522077 FORD CROWN VICTORIA 2011 car safety problem was reported on Oct 11, 2009.FORD CROWN VICTORIA 2011, manufactured by Ford Motor Company had a problem with STEERING . steering this car was a nightmare always pulling to the right. also brakes constantly grabbing and screeching. also headlight and suspension problems. was not happy with this car from start but was slammed into by dealership and chase... i am a senior citizen 76 years old. please help. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 20000 miles. Vehicle Identification Number (VIN):2FABP7EV9BX. Ford Crown Victoria 2011 problem was reported in CENTREVILLE, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 25 mph. Ford Crown Victoria 2011 Service BrakesFord Crown Victoria 2011 Service Brakes Review #10522077 FORD CROWN VICTORIA 2011 car safety problem was reported on Oct 11, 2009.FORD CROWN VICTORIA 2011, manufactured by Ford Motor Company had a problem with SERVICE BRAKES . steering this car was a nightmare always pulling to the right. also brakes constantly grabbing and screeching. also headlight and suspension problems. was not happy with this car from start but was slammed into by dealership and chase... i am a senior citizen 76 years old. please help. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 20000 miles. Vehicle Identification Number (VIN):2FABP7EV9BX. Ford Crown Victoria 2011 problem was reported in CENTREVILLE, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 25 mph. Ford Crown Victoria 2011 SuspensionFord Crown Victoria 2011 Suspension Review #10522077 FORD CROWN VICTORIA 2011 car safety problem was reported on Oct 11, 2009.FORD CROWN VICTORIA 2011, manufactured by Ford Motor Company had a problem with SUSPENSION . steering this car was a nightmare always pulling to the right. also brakes constantly grabbing and screeching. also headlight and suspension problems. was not happy with this car from start but was slammed into by dealership and chase... i am a senior citizen 76 years old. please help. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 20000 miles. Vehicle Identification Number (VIN):2FABP7EV9BX. Ford Crown Victoria 2011 problem was reported in CENTREVILLE, AL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 25 mph. Ford Crown Victoria 2011 StructureFord Crown Victoria 2011 Structure Review #10538335 FORD CROWN VICTORIA 2011 car safety problem was reported on June 06, 2013.FORD CROWN VICTORIA 2011, manufactured by Ford Motor Company had a problem with STRUCTURE . i live in the state of florida, and in may 2013, i purchased a former wisconsin police vehicle, 2011 crown victoria from van horn motors of milwaukee in wisconsin. approximately one month later, after discovering rust particles on my garage floor, i noticed the entire undercarriage, including but not limited to the intermediate steering shaft, mufflers and brake lines are completely covered in rust. this problem was brought to the attention of the dealership via emails with numerous photos attached. no reply was ever received, nor was this problem made aware to me either by landline, email or any other form of communication. in july and part of august 2013, i took it upon myself to physically wash, wire brush, sand, pressure wash, prime and paint the entire undercarriage. since i had to this while lying underneath the vehicle the whole process took me five days to complete and approximately $250.00 in equipment usage, purchases and labor. before and after photos are available effective immediately. i really would like to know, either from the national highway traffic safety administration, the center for auto safety and/or ford motors, how i can please be reimbursed? *js.0 person(s) were injured. 0 person(s) died.Mileage was 116034 miles. Vehicle Identification Number (VIN):2FABP7BV9BX. Ford Crown Victoria 2011 problem was reported in SANFORD, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. Ford Crown Victoria 2011 drive type:RWD. Ford Crown Victoria 2011 WheelsFord Crown Victoria 2011 Wheels Review #10549219 FORD CROWN VICTORIA 2011 car safety problem was reported on Feb 15, 2012.FORD CROWN VICTORIA 2011, manufactured by Ford Motor Company had a problem with WHEELS . tl* the contact owns a 2011 ford crown victoria police package. the contact stated that the front rims would become cracked. the vehicle was taken to the dealer where the technician was unable to diagnose the failure however, the vehicle was repaired. the manufacturer was made aware of the failure. the vin was not available. the failure mileage was 10,000 and the current mileage was 10,900. ...updated 12-23-13 *bf .0 person(s) were injured. 0 person(s) died.Mileage was 10000 miles. Vehicle Identification Number (VIN):2FAHP71V89X. Ford Crown Victoria 2011 problem was reported in DEARBORN, MI. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. Ford Crown Victoria 2011 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Crown Victoria 2011 TRANSMISSION TYPE: AUTO. DEALER'S NAME: GORNO FORD . DEALER'S TELEPHONE NUMBER: 734-676-0031 . DEALER'S CITY: WOODHAVEN . DEALER'S STATE CODE: MI. DEALER'S ZIPCODE: 48183 . Ford Crown Victoria 2011 EngineFord Crown Victoria 2011 Engine Review #10553794 FORD CROWN VICTORIA 2011 car safety problem was reported on Nov 15, 2013.FORD CROWN VICTORIA 2011, manufactured by Ford Motor Company had a problem with ENGINE . car stalls when in high speed passing gear. turns over, will not restart. happened multiple times. was told by dealer this model has a history of this event. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 37002 miles. Vehicle Identification Number (VIN):2FABP7EV9BX. Ford Crown Victoria 2011 problem was reported in WAYNE, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 72 mph. Ford Crown Victoria 2011 Power TrainFord Crown Victoria 2011 Power Train Review #10553794 FORD CROWN VICTORIA 2011 car safety problem was reported on Nov 15, 2013.FORD CROWN VICTORIA 2011, manufactured by Ford Motor Company had a problem with POWER TRAIN . car stalls when in high speed passing gear. turns over, will not restart. happened multiple times. was told by dealer this model has a history of this event. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 37002 miles. Vehicle Identification Number (VIN):2FABP7EV9BX. Ford Crown Victoria 2011 problem was reported in WAYNE, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 72 mph. Ford Crown Victoria 2011 SteeringFord Crown Victoria 2011 Steering Review #10568470 FORD CROWN VICTORIA 2011 car safety problem was reported on Mar 03, 2014.FORD CROWN VICTORIA 2011, manufactured by Ford Motor Company had a problem with STEERING . 2011 ford crown victoria. consumer writes in regards to steering column shaft recall notice. *smd the dealer informed the consumer, the vehicle would be inspected. however, the consumer stated according to the recall notice, the part would be replaced, as well as inspecting otter parts. the service representative responded again, by saying, first there would be an inspection to determine if the part needed to be replaced. the consumer stated he did not want to waste a day, just for an inspection. so he decided to make an appointment with another establishment, to have to part replaced.*jb.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FABP7BV4BX. Ford Crown Victoria 2011 problem was reported in HOUSTON, TX. Original Owner. Vehicle was purchased on June 01, 2012. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. Ford Crown Victoria 2011 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. DEALER'S NAME: TOMMY VAUGHN FORD . DEALER'S CITY: HOUSTON . DEALER'S STATE CODE: TX. DEALER'S ZIPCODE: 77008 . |
-
Ford Crown Victoria 2011 Forum
Discuss and Report Ford Crown Victoria Problems -
Service Bulletins
View Recent Ford Crown Victoria 2011 repair guidance -
Recalls
Latest recall and safety Ford Crown Victoria 2011 information
Ford Crown Victoria 2011 Systems
|
Engine 1 Review(s) Power Train 1 Review(s) Seats 4 Review(s) Service Brakes 1 Review(s) Steering 6 Review(s) Structure 1 Review(s) Suspension 3 Review(s) Wheels 1 Review(s) |
Search 1000s of Car Reviews, Recalls and Technical Bulletins
Start by entering a car model, system, manufacturer or any combination of keywords.
Ford Crown Victoria 2011 Reports
my 95 ford exploere engine surges when turn my air conditioner on Ihave a 1994 ford probe which has started to idle very low and stalls at times. It is a 4 cyl. w/ air and a 5 speed. any ideas? I replaced the fuel filter, air flow meter and added HEAT to gas tank to dry and clean fuel system. I think my pcv valv should a standard transmission truck start when it is in gear without the clucth engaged? should a 2005 standard transmission ford ranger start when in gear without the clutch engaged? 96 Ford F250 Emergency brake lever gets caught on the auto adjustment spring, causing brakes to be permanently engaged, also allowing the parking break lever to rub against the hub, which can cut through over time. try pushing the pedals button closer to you. you must have the pedal adjustment button to the left of the radio, looks like a foot, that brings the pedals more inward towards the driver. hope it helped. or look carefully if a wire has corroded. it i would check ur multi switch on ur stearing colum on the pedal whats the sound Just bought an '06 E-350 van. Left d'ship got on highway and noticed shimmy when I got to 60....same problem???? that happened to me last night! If you rock the car back and for while shifting then it should release the safety lock! why does it take turning off the veh. while pulling in on the shifter arm, them starting it again while still holding it inwards ever so slightly??