Car-and-Safety.com

Ford Crown Victoria 2007 Safety Reports and Reviews



Ford Crown Victoria 2007 Reviews



Ford Crown Victoria 2007 Steering

Ford Crown Victoria 2007 Steering Review #10208481

FORD CROWN VICTORIA 2007 car safety problem was reported on Aug 23, 2007.FORD CROWN VICTORIA 2007, manufactured by FORD MOTOR COMPANY had a problem with STEERING . loss of power steering during abrupt and normal turning. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 10000 miles. Vehicle Identification Number (VIN):2FAHP71W67X. Ford Crown Victoria 2007 problem was reported in CLARKSVILLE, TN. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. Ford Crown Victoria 2007 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. VEHICLE SPEED: 20 mph.

Ford Crown Victoria 2007 Steering Hydraulic Power Assist System

Ford Crown Victoria 2007 Steering Hydraulic Power Assist System Review #10212658

FORD CROWN VICTORIA 2007 car safety problem was reported on Nov 02, 2007.FORD CROWN VICTORIA 2007, manufactured by FORD MOTOR COMPANY had a problem with STEERING:HYDRAULIC POWER ASSIST SYSTEM . during deceleration of the ford cvpi, the vehicle's power steering fails. it makes the police unit very hard to control during routine police vehicle operations such as u-turns, sharp turns, or during any type of situation where the vehicle's speed is quickly slowed, and a turn is initiated. *tr.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FAFP71WX7X. Ford Crown Victoria 2007 problem was reported in CONYERS, GA. Original Owner. Vehicle was purchased on July 01, 2007. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. FUEL SYSTEM:Fuel injection. Ford Crown Victoria 2007 TRANSMISSION TYPE: AUTO. DEALER'S NAME: ALAN VIGIL FORD . DEALER'S CITY: MORROW . DEALER'S STATE CODE: GA.

Ford Crown Victoria 2007 Power Train Driveline

Ford Crown Victoria 2007 Power Train Driveline Review #10228120

FORD CROWN VICTORIA 2007 car safety problem was reported on May 10, 2008.FORD CROWN VICTORIA 2007, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:DRIVELINE . this is a request for a monthly inspection(s) analysis, to determine recalls defects at the following locations: ntb, discount, goodyear, firestones-all makes, brands, models. please check for defects and inspect tire height, sizes, widths for technological and engineering defects. *tr.Ford Crown Victoria 2007 problem was reported in HOUSTON, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Crown Victoria 2007 Unknown Or Other

Ford Crown Victoria 2007 Unknown Or Other Review #10228120

FORD CROWN VICTORIA 2007 car safety problem was reported on May 10, 2008.FORD CROWN VICTORIA 2007, manufactured by FORD MOTOR COMPANY had a problem with UNKNOWN OR OTHER . this is a request for a monthly inspection(s) analysis, to determine recalls defects at the following locations: ntb, discount, goodyear, firestones-all makes, brands, models. please check for defects and inspect tire height, sizes, widths for technological and engineering defects. *tr.Ford Crown Victoria 2007 problem was reported in HOUSTON, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Crown Victoria 2007 Tires Tread/belt

Ford Crown Victoria 2007 Tires Tread/belt Review #10236646

FORD CROWN VICTORIA 2007 car safety problem was reported on July 26, 2008.FORD CROWN VICTORIA 2007, manufactured by FORD MOTOR COMPANY had a problem with TIRES:TREAD/BELT . tl*the contact owns a 2007 ford crown victoria. the vehicle has goodyear eagle ls tires, size p225/60r16. while driving 55 mph, the contact heard a strange noise coming from the rear of the vehicle. he lost control of the steering wheel and almost crashed. he pulled over and noticed that the rear passenger side tire had completely shredded off. there is approximately an inch of rubber remaining around the diameter of the tire. emergency roadside service placed a spare tire on the vehicle. he went to the ford dealer and was informed that they were not responsible for the failure with the tires. the contact was advised to call goodyear; however, he emailed them and was informed to give them a call. the failure mileage was 6,450. updated 09/15/08 *bf updated 09/19/08. *jb.0 person(s) were injured. 0 person(s) died.Mileage was 6450 miles. Vehicle Identification Number (VIN):2FDHP74W07X. Ford Crown Victoria 2007 problem was reported in YARDLEY, PA. Original Owner. Vehicle was purchased on June 30, 2007. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. Ford Crown Victoria 2007 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Crown Victoria 2007 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 55 mph. DEALER'S NAME: WARNOCK FORD . DEALER'S TELEPHONE NUMBER: 973-644-3200 . DEALER'S CITY: MORRISTOWN . DEALER'S STATE CODE: NJ. DEALER'S ZIPCODE: 07962 .

Ford Crown Victoria 2007 Fuel System, Gasoline

Ford Crown Victoria 2007 Fuel System, Gasoline Review #10355856

FORD CROWN VICTORIA 2007 car safety problem was reported on Sept 15, 2010.FORD CROWN VICTORIA 2007, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE . ford crown vic police interceptor,2007: on two previous occasions, upon depressing brake pedal at stop sign, engine would seem to begin to race; however, after stop i would immediately let off brake to go on through stop sign and engine was normal on acceleration. to-day as i left my parking space i approached an automatic gate to pass through and depressed brake pedal to wait for gate to open and engine began to race to the point that i was unable to hold vehicle back and turned off ignition to avoid hitting gate. a large amount of black smoke resulted from racing engine. after engine shut-down, i shifted to park, started engine and had normal idle. i depressed brake to shift into drive and proceeded through gate in normal manner. the only common system that i am aware of (other than possible electrical/computer) to the fuel control is the vacuum system associated with the brake vacuum booster and whatever vacuum may affect the fuel feed. the foot pedal was definitely in an idle position. i am certain that this engine racing problem is initiated by my applying brakes. *tr.Mileage was 68671 miles. Vehicle Identification Number (VIN):2FAHP71W77X. Ford Crown Victoria 2007 problem was reported in CONYERS, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 2 mph.

Ford Crown Victoria 2007 Vehicle Speed Control

Ford Crown Victoria 2007 Vehicle Speed Control Review #10355856

FORD CROWN VICTORIA 2007 car safety problem was reported on Sept 15, 2010.FORD CROWN VICTORIA 2007, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . ford crown vic police interceptor,2007: on two previous occasions, upon depressing brake pedal at stop sign, engine would seem to begin to race; however, after stop i would immediately let off brake to go on through stop sign and engine was normal on acceleration. to-day as i left my parking space i approached an automatic gate to pass through and depressed brake pedal to wait for gate to open and engine began to race to the point that i was unable to hold vehicle back and turned off ignition to avoid hitting gate. a large amount of black smoke resulted from racing engine. after engine shut-down, i shifted to park, started engine and had normal idle. i depressed brake to shift into drive and proceeded through gate in normal manner. the only common system that i am aware of (other than possible electrical/computer) to the fuel control is the vacuum system associated with the brake vacuum booster and whatever vacuum may affect the fuel feed. the foot pedal was definitely in an idle position. i am certain that this engine racing problem is initiated by my applying brakes. *tr.Mileage was 68671 miles. Vehicle Identification Number (VIN):2FAHP71W77X. Ford Crown Victoria 2007 problem was reported in CONYERS, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 2 mph.

Ford Crown Victoria 2007 Electrical System

Ford Crown Victoria 2007 Electrical System Review #10373380

FORD CROWN VICTORIA 2007 car safety problem was reported on Dec 29, 2010.FORD CROWN VICTORIA 2007, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . this is the fourth event of increasing engine rpm when depressing brake to stop at a stop sign. as in two other events, no traffic was approaching so i had immediately went from a stop (noting increasing engine rpm) to removing foot from brake pedal to go to gas pedal to proceed on past stop resulting in the increasing engine rpm being a non-event in terms of engine racing out of control. not so with a third event in which i stopped at an automatic gate and had to stay stopped with engine rpm again increasing and continuously to increase to the point that i had to lock down on brake to keep from being pulled into the gate and was able to completely stop by cutting off the ignition. this third racing out of control was reported by confirmation number (odi) 10355856. this third event resulted in the vehicle manufacturer asking me to take car to local dealer where car was left for a day with result of 'no trouble found' and service advisor's opinion "you had foot on brake and gas at the same time". not so. i had specifically checked for this condition at time of attempted stop. this third event occurred 9/15/2010. *tr.Mileage was 73989 miles. Vehicle Identification Number (VIN):2FAHP71W77X. Ford Crown Victoria 2007 problem was reported in CONYERS, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. Ford Crown Victoria 2007 drive type:RWD. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Fuel System, Gasoline

Ford Crown Victoria 2007 Fuel System, Gasoline Review #10373380

FORD CROWN VICTORIA 2007 car safety problem was reported on Dec 29, 2010.FORD CROWN VICTORIA 2007, manufactured by FORD MOTOR COMPANY had a problem with FUEL SYSTEM, GASOLINE . this is the fourth event of increasing engine rpm when depressing brake to stop at a stop sign. as in two other events, no traffic was approaching so i had immediately went from a stop (noting increasing engine rpm) to removing foot from brake pedal to go to gas pedal to proceed on past stop resulting in the increasing engine rpm being a non-event in terms of engine racing out of control. not so with a third event in which i stopped at an automatic gate and had to stay stopped with engine rpm again increasing and continuously to increase to the point that i had to lock down on brake to keep from being pulled into the gate and was able to completely stop by cutting off the ignition. this third racing out of control was reported by confirmation number (odi) 10355856. this third event resulted in the vehicle manufacturer asking me to take car to local dealer where car was left for a day with result of 'no trouble found' and service advisor's opinion "you had foot on brake and gas at the same time". not so. i had specifically checked for this condition at time of attempted stop. this third event occurred 9/15/2010. *tr.Mileage was 73989 miles. Vehicle Identification Number (VIN):2FAHP71W77X. Ford Crown Victoria 2007 problem was reported in CONYERS, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. Ford Crown Victoria 2007 drive type:RWD. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Engine And Engine Cooling

Ford Crown Victoria 2007 Engine And Engine Cooling Review #10409449

FORD CROWN VICTORIA 2007 car safety problem was reported on June 19, 2011.FORD CROWN VICTORIA 2007, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . this is another of an on going acceleration issue when depressing the foot brake. in this instance i had just backed out of a parking space in a shopping center and drove maybe 200' and had just about rolled to a stop sign for ga highway 212 and very slightly depressed the brake pedal to come to a complete stop. as soon as i started pressing the brake pedal, the engine picked up rpm and i immediately moved foot from brake pedal. end of acceleration. by this time vehicle had already rolled to a complete stop. i did not, as ford seems to think, have my foot on both the gas and brake. the very light pressure i had applied would have my foot three to four inches away from the top of the gas pedal. yes, i had my foot on the brake. i had to remove my foot from the gas to get to the brake. this is a vehicle malfunction. not operator error. i am unable to determine a failed component.....fuel? brake? electrical? i don't have a clue..0 person(s) were injured. 0 person(s) died.Mileage was 81243 miles. Vehicle Identification Number (VIN):2FAHP71W77X. Ford Crown Victoria 2007 problem was reported in CONYERS, GA. Vehicle was not using Cruise Control. VEHICLE SPEED: 1 mph.

Ford Crown Victoria 2007 Vehicle Speed Control

Ford Crown Victoria 2007 Vehicle Speed Control Review #10409449

FORD CROWN VICTORIA 2007 car safety problem was reported on June 19, 2011.FORD CROWN VICTORIA 2007, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . this is another of an on going acceleration issue when depressing the foot brake. in this instance i had just backed out of a parking space in a shopping center and drove maybe 200' and had just about rolled to a stop sign for ga highway 212 and very slightly depressed the brake pedal to come to a complete stop. as soon as i started pressing the brake pedal, the engine picked up rpm and i immediately moved foot from brake pedal. end of acceleration. by this time vehicle had already rolled to a complete stop. i did not, as ford seems to think, have my foot on both the gas and brake. the very light pressure i had applied would have my foot three to four inches away from the top of the gas pedal. yes, i had my foot on the brake. i had to remove my foot from the gas to get to the brake. this is a vehicle malfunction. not operator error. i am unable to determine a failed component.....fuel? brake? electrical? i don't have a clue..0 person(s) were injured. 0 person(s) died.Mileage was 81243 miles. Vehicle Identification Number (VIN):2FAHP71W77X. Ford Crown Victoria 2007 problem was reported in CONYERS, GA. Vehicle was not using Cruise Control. VEHICLE SPEED: 1 mph.

Ford Crown Victoria 2007 Service Brakes, Hydraulic

Ford Crown Victoria 2007 Service Brakes, Hydraulic Review #10437265

FORD CROWN VICTORIA 2007 car safety problem was reported on Nov 07, 2011.FORD CROWN VICTORIA 2007, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC . tl* the contact owns a 2007 ford crown victoria. the contact stated that while driving up an incline at approximately 30 mph, the brake and the abs lights illuminated. the contact also stated that the vehicle began to experience an increased stopping distance after the lights illuminated. the vehicle was taken to a local repair shop, who performed a diagnostic test that was unable to locate a failure code. the manufacturer was notified of the failure. the vehicle was not repaired. the failure mileage was 90,000 and the current mileage was 90,700. .Mileage was 90000 miles. Vehicle Identification Number (VIN):2FAHP71W77X. Ford Crown Victoria 2007 problem was reported in CORONA, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Ford Crown Victoria 2007 Electrical System

Ford Crown Victoria 2007 Electrical System Review #10445654

FORD CROWN VICTORIA 2007 car safety problem was reported on Jan 27, 2012.FORD CROWN VICTORIA 2007, manufactured by FORD MOTOR COMPANY had a problem with ELECTRICAL SYSTEM . paint peeling on hood and top also, heater blend door not working. *tr .Vehicle Identification Number (VIN):2FAFP74V67X. Ford Crown Victoria 2007 problem was reported in ELLISVILLE, MS. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: BIFUEL.

Ford Crown Victoria 2007 Structure

Ford Crown Victoria 2007 Structure Review #10445654

FORD CROWN VICTORIA 2007 car safety problem was reported on Jan 27, 2012.FORD CROWN VICTORIA 2007, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE . paint peeling on hood and top also, heater blend door not working. *tr .Vehicle Identification Number (VIN):2FAFP74V67X. Ford Crown Victoria 2007 problem was reported in ELLISVILLE, MS. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: BIFUEL.

Ford Crown Victoria 2007 Visibility Defroster/defogger System

Ford Crown Victoria 2007 Visibility Defroster/defogger System Review #10445654

FORD CROWN VICTORIA 2007 car safety problem was reported on Jan 27, 2012.FORD CROWN VICTORIA 2007, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:DEFROSTER/DEFOGGER SYSTEM . paint peeling on hood and top also, heater blend door not working. *tr .Vehicle Identification Number (VIN):2FAFP74V67X. Ford Crown Victoria 2007 problem was reported in ELLISVILLE, MS. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: BIFUEL.

Ford Crown Victoria 2007 Steering

Ford Crown Victoria 2007 Steering Review #10475950

FORD CROWN VICTORIA 2007 car safety problem was reported on Sept 11, 2012.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with STEERING . tuesday sept. 11 stating that while coming to a stop she lost steering on her vehicle. she said that the steering wheel turned freely and the horn was stuck on. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 158038 miles. Vehicle Identification Number (VIN):2FAHP71W57X. Ford Crown Victoria 2007 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 10 mph.

Ford Crown Victoria 2007 Steering Column

Ford Crown Victoria 2007 Steering Column Review #10477701

FORD CROWN VICTORIA 2007 car safety problem was reported on July 01, 2012.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with STEERING:COLUMN . this fleet, even though there were no complete separations of the steering shaft assembly, has experienced steering column issues in which the green sleeve in the upper end of the column closest to the steering wheel has protruded indicating the upper portion of the steering column began to separate. updated 10/25/12*lj updated 10/26/2012 *js.Vehicle Identification Number (VIN):2FAFP71W47X. Ford Crown Victoria 2007 problem was reported in JESSUP, MD. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. Ford Crown Victoria 2007 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Crown Victoria 2007 TRANSMISSION TYPE: AUTO.

Ford Crown Victoria 2007 Steering Review #10478035

FORD CROWN VICTORIA 2007 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with STEERING . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 118985 miles. Vehicle Identification Number (VIN):2FAHP71W77X. Ford Crown Victoria 2007 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Suspension

Ford Crown Victoria 2007 Suspension Review #10478035

FORD CROWN VICTORIA 2007 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with SUSPENSION . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 118985 miles. Vehicle Identification Number (VIN):2FAHP71W77X. Ford Crown Victoria 2007 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Suspension Review #10478036

FORD CROWN VICTORIA 2007 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with SUSPENSION . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 104619 miles. Vehicle Identification Number (VIN):2FAHP71W97X. Ford Crown Victoria 2007 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Steering

Ford Crown Victoria 2007 Steering Review #10478036

FORD CROWN VICTORIA 2007 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with STEERING . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 104619 miles. Vehicle Identification Number (VIN):2FAHP71W97X. Ford Crown Victoria 2007 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Steering Review #10478037

FORD CROWN VICTORIA 2007 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with STEERING . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 140909 miles. Vehicle Identification Number (VIN):2FAHP71W27X. Ford Crown Victoria 2007 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Suspension

Ford Crown Victoria 2007 Suspension Review #10478037

FORD CROWN VICTORIA 2007 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with SUSPENSION . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 140909 miles. Vehicle Identification Number (VIN):2FAHP71W27X. Ford Crown Victoria 2007 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Suspension Review #10478039

FORD CROWN VICTORIA 2007 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with SUSPENSION . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 124171 miles. Vehicle Identification Number (VIN):2FAHP71W17X. Ford Crown Victoria 2007 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Steering

Ford Crown Victoria 2007 Steering Review #10478039

FORD CROWN VICTORIA 2007 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with STEERING . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 124171 miles. Vehicle Identification Number (VIN):2FAHP71W17X. Ford Crown Victoria 2007 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Suspension

Ford Crown Victoria 2007 Suspension Review #10478048

FORD CROWN VICTORIA 2007 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with SUSPENSION . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 124650 miles. Vehicle Identification Number (VIN):2FAHP71W07X. Ford Crown Victoria 2007 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Steering

Ford Crown Victoria 2007 Steering Review #10478048

FORD CROWN VICTORIA 2007 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with STEERING . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 124650 miles. Vehicle Identification Number (VIN):2FAHP71W07X. Ford Crown Victoria 2007 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Steering Review #10480750

FORD CROWN VICTORIA 2007 car safety problem was reported on Oct 09, 2012.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with STEERING . steering wheel became very hard to turn and would not bring itself back to straight position on its own. also a clicking noise could be heard from the steering column when turning the steering wheel. ford dealership found that the upper steering shaft had malfunctioned. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 67257 miles. Vehicle Identification Number (VIN):2FAHP71W87X. Ford Crown Victoria 2007 problem was reported in PARIS, KY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Steering Review #10480915

FORD CROWN VICTORIA 2007 car safety problem was reported on Oct 17, 2012.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with STEERING . the steering shaft bushing became dislodged and fell out of position. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 85000 miles. Ford Crown Victoria 2007 problem was reported in WOODBURY, CT. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Crown Victoria 2007 Vehicle Speed Control

Ford Crown Victoria 2007 Vehicle Speed Control Review #10481071

FORD CROWN VICTORIA 2007 car safety problem was reported on Oct 18, 2012.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with VEHICLE SPEED CONTROL . the operator of the vehicle applied the brake and stopped the vehicle, however, it started to accelerate on its own and move forward. the engine continued to rev and the vehicle continued to move forward to the point that the operator had to place two feet on the brake. there have been several other complaints of this nature regarding crown victorias. this vehicle is a 2007 ford crown victoria police vehicle. *tr.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FAHP71W67X. Ford Crown Victoria 2007 problem was reported in ALEXANDRIA, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Engine

Ford Crown Victoria 2007 Engine Review #10481071

FORD CROWN VICTORIA 2007 car safety problem was reported on Oct 18, 2012.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with ENGINE . the operator of the vehicle applied the brake and stopped the vehicle, however, it started to accelerate on its own and move forward. the engine continued to rev and the vehicle continued to move forward to the point that the operator had to place two feet on the brake. there have been several other complaints of this nature regarding crown victorias. this vehicle is a 2007 ford crown victoria police vehicle. *tr.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FAHP71W67X. Ford Crown Victoria 2007 problem was reported in ALEXANDRIA, VA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Engine Review #10486259

FORD CROWN VICTORIA 2007 car safety problem was reported on Jan 03, 2012.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with ENGINE . leaking intake manifold at the coolant crossover (thermostat housing). aluminum crossover becomes separated from the plastic intake manifold which will cause overheating and severe engine damage at all speeds. the entire intake manifold will have to be replaced if this condition occurs. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 104000 miles. Ford Crown Victoria 2007 problem was reported in LEAGUE CITY, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Crown Victoria 2007 Vehicle Speed Control

Ford Crown Victoria 2007 Vehicle Speed Control Review #10493079

FORD CROWN VICTORIA 2007 car safety problem was reported on Jan 12, 2013.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2007 ford crown victoria. the contact stated that while waiting at a traffic stop sign with the brakes applied, the vehicle lunged forward as the engine rpm's raced. the contact then shifted into neutral as the vehicle continued to lunge forward. the contact was able to move off the road, shut off and restart the vehicle. the vehicle was taken to an independent mechanic where they advised him that the throttle body and position sensor failed due to a build up of carbon. the vehicle was repaired by the replacement of the throttle bottle unit, sensor and a cleaning of the fuel system. the manufacturer was not contacted. the failure and current mileages were approximately 127,350. updated 6/11/13 *cn the consumer also stated upon shifting into neutral and applying the brake, the vehicle stopped half-way through the traffic intersection. also, while in neutral, the vehicle's rpm gauge reached over 3,000 rpm. the consumer shut the vehicle off and re-started it three times. on the 4th re-start, normal idle returned. updated 06/12/13.0 person(s) were injured. 0 person(s) died.Mileage was 127350 miles. Vehicle Identification Number (VIN):2FAHP71W47X. Ford Crown Victoria 2007 problem was reported in GROSSE POINTE, MI. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. Ford Crown Victoria 2007 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Crown Victoria 2007 TRANSMISSION TYPE: AUTO. DEALER'S NAME: AUTO LAB . DEALER'S TELEPHONE NUMBER: 586-360-2500 . DEALER'S CITY: ST. CLAIR SHORES . DEALER'S STATE CODE: MI. DEALER'S ZIPCODE: 48080 .

Ford Crown Victoria 2007 Vehicle Speed Control Review #10505465

FORD CROWN VICTORIA 2007 car safety problem was reported on Mar 25, 2013.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with VEHICLE SPEED CONTROL . the operator of the vehicle applied the brake to stop at traffic light engine started to rev and accelerate on its own and move forward. *tr.0 person(s) were injured. 0 person(s) died.Ford Crown Victoria 2007 problem was reported in NEW BRAUNFELS, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Crown Victoria 2007 Engine

Ford Crown Victoria 2007 Engine Review #10505465

FORD CROWN VICTORIA 2007 car safety problem was reported on Mar 25, 2013.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with ENGINE . the operator of the vehicle applied the brake to stop at traffic light engine started to rev and accelerate on its own and move forward. *tr.0 person(s) were injured. 0 person(s) died.Ford Crown Victoria 2007 problem was reported in NEW BRAUNFELS, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Crown Victoria 2007 Steering

Ford Crown Victoria 2007 Steering Review #10507014

FORD CROWN VICTORIA 2007 car safety problem was reported on Apr 01, 2013.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with STEERING . when making turns steering wheel would make clicking sounds. had mechanic check and he found that the inner shaft of the steering column had slipped down. *tr updated 04/24/13 *bf .0 person(s) were injured. 0 person(s) died.Mileage was 34391 miles. Vehicle Identification Number (VIN):2FAFP73V67X. Ford Crown Victoria 2007 problem was reported in SCOTTSDALE, AZ. Vehicle was purchased on July 21, 2007. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. Ford Crown Victoria 2007 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: BIFUEL. Ford Crown Victoria 2007 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 40 mph. DEALER'S NAME: FIVE STAR FORD . DEALER'S CITY: SCOTTSDALE . DEALER'S STATE CODE: AZ.

Ford Crown Victoria 2007 Structure Body

Ford Crown Victoria 2007 Structure Body Review #10509218

FORD CROWN VICTORIA 2007 car safety problem was reported on Apr 15, 2013.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with STRUCTURE:BODY . steering effort is increasing. the steering column moves and clicks upon acceleration. steering is increasing getting harder to control. also have had the roof repainted by ford while under manufacture warranty due to paint peeling in large sheets of roof, now the front hood has large peeling paint leaving the green coating showing. ford will not cover now as out of warranty. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 48383 miles. Vehicle Identification Number (VIN):2FAFP74V07X. Ford Crown Victoria 2007 problem was reported in WHITING, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. VEHICLE SPEED: 45 mph.

Ford Crown Victoria 2007 Steering

Ford Crown Victoria 2007 Steering Review #10509218

FORD CROWN VICTORIA 2007 car safety problem was reported on Apr 15, 2013.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with STEERING . steering effort is increasing. the steering column moves and clicks upon acceleration. steering is increasing getting harder to control. also have had the roof repainted by ford while under manufacture warranty due to paint peeling in large sheets of roof, now the front hood has large peeling paint leaving the green coating showing. ford will not cover now as out of warranty. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 48383 miles. Vehicle Identification Number (VIN):2FAFP74V07X. Ford Crown Victoria 2007 problem was reported in WHITING, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. VEHICLE SPEED: 45 mph.

Ford Crown Victoria 2007 Vehicle Speed Control

Ford Crown Victoria 2007 Vehicle Speed Control Review #10510474

FORD CROWN VICTORIA 2007 car safety problem was reported on Apr 17, 2013.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with VEHICLE SPEED CONTROL . i drive a ford "program car" - a used 2007 crown victoria (a former rental vehicle). on the day of my accident - after pulling onto a busy street from a parking lot - i almost immediately applied my brakes because i was coming up to a red light where several cars had already come to a stop ahead of me. at first my car slowed normally but, as i applied the brakes to come to a complete stop, the engine began to rev' up. i tried tapping the brake to see if this would help to disengage the throttle's revving. it didn't help. i kept trying this. i had little time to come to a stop before hitting the car in front of me so i really "stood" on the brakes. unfortunately, i hit the back bumper of the car in front of me. luckily, there was no visible damage to either car and no one was hurt. this same situation happened to me about 2-3 weeks before this accident occurred but that occurrence didn't result in an accident. i was able to tap the brake pedal and the revving seemed to instantly go away. i had a passenger with me at the time. i had the same thing happen with another similar car in the past - a mercury grand marquis. it happened more than once and no matter how often i went to the dealership to get help they kept telling me they could not "replicate" the complaint. i took my current crown victoria to the dealership one day after having this minor accident. the car was due for a service visit and i told them about the minor accident and asked them to see what they could find out. again, i was told they could not replicate the complaint. i know i'm not the only person who has had this happen as a class action suit has been filed against ford in march in west virginia on behalf of owners in 14 states! apparently, this is not a one time thing with these vehicles. *tr.Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Mileage was 47362 miles. Vehicle Identification Number (VIN):2FAFP74V27X. Ford Crown Victoria 2007 problem was reported in OPELOUSAS, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph.

Ford Crown Victoria 2007 Service Brakes

Ford Crown Victoria 2007 Service Brakes Review #10510474

FORD CROWN VICTORIA 2007 car safety problem was reported on Apr 17, 2013.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with SERVICE BRAKES . i drive a ford "program car" - a used 2007 crown victoria (a former rental vehicle). on the day of my accident - after pulling onto a busy street from a parking lot - i almost immediately applied my brakes because i was coming up to a red light where several cars had already come to a stop ahead of me. at first my car slowed normally but, as i applied the brakes to come to a complete stop, the engine began to rev' up. i tried tapping the brake to see if this would help to disengage the throttle's revving. it didn't help. i kept trying this. i had little time to come to a stop before hitting the car in front of me so i really "stood" on the brakes. unfortunately, i hit the back bumper of the car in front of me. luckily, there was no visible damage to either car and no one was hurt. this same situation happened to me about 2-3 weeks before this accident occurred but that occurrence didn't result in an accident. i was able to tap the brake pedal and the revving seemed to instantly go away. i had a passenger with me at the time. i had the same thing happen with another similar car in the past - a mercury grand marquis. it happened more than once and no matter how often i went to the dealership to get help they kept telling me they could not "replicate" the complaint. i took my current crown victoria to the dealership one day after having this minor accident. the car was due for a service visit and i told them about the minor accident and asked them to see what they could find out. again, i was told they could not replicate the complaint. i know i'm not the only person who has had this happen as a class action suit has been filed against ford in march in west virginia on behalf of owners in 14 states! apparently, this is not a one time thing with these vehicles. *tr.Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Mileage was 47362 miles. Vehicle Identification Number (VIN):2FAFP74V27X. Ford Crown Victoria 2007 problem was reported in OPELOUSAS, LA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 15 mph.

Ford Crown Victoria 2007 Engine

Ford Crown Victoria 2007 Engine Review #10575013

FORD CROWN VICTORIA 2007 car safety problem was reported on July 01, 2007.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with ENGINE . while driving the vehicle at highway speeds (60-70mph) going uphill, while making a sharp turn left or while rocking the steering wheel to make the rear of the car sway slightly to the left, there is a surge and complete loss of power for 1/2 second. this causes a surge/jolt feeling in the vehicle like the vehicle transmission or engine has lost all power. if you try to sway the vehicle immediately a 2nd time nothing happens. if you wait several minutes and sway the rear end again there is again a heavy surge and loss of power. i also observed the tac-ometer show a loss of power for a brief moment. if you are going up hill at highway speeds and the vehicle sways to the right or you swerve the steering wheel to make the vehicle swerve to the right (body rock to the right) nothing will ever happen. it is only on left body rock while at highway speeds on an incline. there are no trouble codes. there is no indicator light or dash flash or buzzer. nothing happens and nothing triggers a diagnostic code. all codes are clear. there are two bulletins posted on the nhtsa website. 1. id# 10024695 & 2. id# 10039053. when calling ford @ 800-392-3673 they are unable to provide any information or help regarding this matter or the bulletins mentioned. they advise there are no bulletins at all for my vehicle. this problem started when the vehicle was brand new. the dealership in california was unable to diagnose the problem because it was intermittent. now at 54,000 miles the problem happens 8 or 10 times in a 30 mile trip. it is very troubling that the vehicle loses power and surges. it causes a panic in the passenger compartment when happening! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 2500 miles. Vehicle Identification Number (VIN):2FAHP74V67X. Ford Crown Victoria 2007 problem was reported in FERNLEY, NV. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 70 mph.

Ford Crown Victoria 2007 Electrical System

Ford Crown Victoria 2007 Electrical System Review #10575013

FORD CROWN VICTORIA 2007 car safety problem was reported on July 01, 2007.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with ELECTRICAL SYSTEM . while driving the vehicle at highway speeds (60-70mph) going uphill, while making a sharp turn left or while rocking the steering wheel to make the rear of the car sway slightly to the left, there is a surge and complete loss of power for 1/2 second. this causes a surge/jolt feeling in the vehicle like the vehicle transmission or engine has lost all power. if you try to sway the vehicle immediately a 2nd time nothing happens. if you wait several minutes and sway the rear end again there is again a heavy surge and loss of power. i also observed the tac-ometer show a loss of power for a brief moment. if you are going up hill at highway speeds and the vehicle sways to the right or you swerve the steering wheel to make the vehicle swerve to the right (body rock to the right) nothing will ever happen. it is only on left body rock while at highway speeds on an incline. there are no trouble codes. there is no indicator light or dash flash or buzzer. nothing happens and nothing triggers a diagnostic code. all codes are clear. there are two bulletins posted on the nhtsa website. 1. id# 10024695 & 2. id# 10039053. when calling ford @ 800-392-3673 they are unable to provide any information or help regarding this matter or the bulletins mentioned. they advise there are no bulletins at all for my vehicle. this problem started when the vehicle was brand new. the dealership in california was unable to diagnose the problem because it was intermittent. now at 54,000 miles the problem happens 8 or 10 times in a 30 mile trip. it is very troubling that the vehicle loses power and surges. it causes a panic in the passenger compartment when happening! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 2500 miles. Vehicle Identification Number (VIN):2FAHP74V67X. Ford Crown Victoria 2007 problem was reported in FERNLEY, NV. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 70 mph.

Ford Crown Victoria 2007 Fuel/propulsion System

Ford Crown Victoria 2007 Fuel/propulsion System Review #10575013

FORD CROWN VICTORIA 2007 car safety problem was reported on July 01, 2007.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with FUEL/PROPULSION SYSTEM . while driving the vehicle at highway speeds (60-70mph) going uphill, while making a sharp turn left or while rocking the steering wheel to make the rear of the car sway slightly to the left, there is a surge and complete loss of power for 1/2 second. this causes a surge/jolt feeling in the vehicle like the vehicle transmission or engine has lost all power. if you try to sway the vehicle immediately a 2nd time nothing happens. if you wait several minutes and sway the rear end again there is again a heavy surge and loss of power. i also observed the tac-ometer show a loss of power for a brief moment. if you are going up hill at highway speeds and the vehicle sways to the right or you swerve the steering wheel to make the vehicle swerve to the right (body rock to the right) nothing will ever happen. it is only on left body rock while at highway speeds on an incline. there are no trouble codes. there is no indicator light or dash flash or buzzer. nothing happens and nothing triggers a diagnostic code. all codes are clear. there are two bulletins posted on the nhtsa website. 1. id# 10024695 & 2. id# 10039053. when calling ford @ 800-392-3673 they are unable to provide any information or help regarding this matter or the bulletins mentioned. they advise there are no bulletins at all for my vehicle. this problem started when the vehicle was brand new. the dealership in california was unable to diagnose the problem because it was intermittent. now at 54,000 miles the problem happens 8 or 10 times in a 30 mile trip. it is very troubling that the vehicle loses power and surges. it causes a panic in the passenger compartment when happening! *tr.0 person(s) were injured. 0 person(s) died.Mileage was 2500 miles. Vehicle Identification Number (VIN):2FAHP74V67X. Ford Crown Victoria 2007 problem was reported in FERNLEY, NV. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: BIFUEL. VEHICLE SPEED: 70 mph.

Ford Crown Victoria 2007 Engine And Engine Cooling Exhaust System Manifold/header/muffler/tail Pipe

Ford Crown Victoria 2007 Engine And Engine Cooling Exhaust System Manifold/header/muffler/tail Pipe Review #10583112

FORD CROWN VICTORIA 2007 car safety problem was reported on Mar 24, 2014.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE . intake manifold is subject to extremely high temperatures. ford's current design includes a plastic intake manifold that is susceptible to warping and may cause engine failure if coolant looses pressure due to leak. *tt.0 person(s) were injured. 0 person(s) died.Mileage was 48000 miles. Vehicle Identification Number (VIN):2FAHP71W37X. Ford Crown Victoria 2007 problem was reported in CARSON, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Electrical System

Ford Crown Victoria 2007 Electrical System Review #10605582

FORD CROWN VICTORIA 2007 car safety problem was reported on June 11, 2014.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with ELECTRICAL SYSTEM . i came to normal stop at 4 way stop sign. started across road and vehicle to my left failed to yield right of way and i had to panic stop. as i hit brakes for panic stop, engine rpm went to max, pulling car forward while i was hard on brakes. i missed violator by only inches. as soon as i let off brakes, engine rpm returned to normal. ford dealer has previously concluded i hit gas instead of brakes. this is totally absurd in every instance of this event. had i hit the brakes in this latest incident, i would have totaled the car i was trying to avoid. i am reporting this incident (one of at least a half dozen previous incidents) because this was so close to an accident. in past incidents i have stopped "brake/increase rpm" by simply cutting off ignition. this reported incident happened so fast, i had no time to cut ignition, nor would this have been a good time to cut ignition. *tr.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FAHP71W77X. Ford Crown Victoria 2007 problem was reported in CONYERS, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 4 mph.

Ford Crown Victoria 2007 Vehicle Speed Control

Ford Crown Victoria 2007 Vehicle Speed Control Review #10605582

FORD CROWN VICTORIA 2007 car safety problem was reported on June 11, 2014.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with VEHICLE SPEED CONTROL . i came to normal stop at 4 way stop sign. started across road and vehicle to my left failed to yield right of way and i had to panic stop. as i hit brakes for panic stop, engine rpm went to max, pulling car forward while i was hard on brakes. i missed violator by only inches. as soon as i let off brakes, engine rpm returned to normal. ford dealer has previously concluded i hit gas instead of brakes. this is totally absurd in every instance of this event. had i hit the brakes in this latest incident, i would have totaled the car i was trying to avoid. i am reporting this incident (one of at least a half dozen previous incidents) because this was so close to an accident. in past incidents i have stopped "brake/increase rpm" by simply cutting off ignition. this reported incident happened so fast, i had no time to cut ignition, nor would this have been a good time to cut ignition. *tr.0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FAHP71W77X. Ford Crown Victoria 2007 problem was reported in CONYERS, GA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 4 mph.

Ford Crown Victoria 2007 Engine

Ford Crown Victoria 2007 Engine Review #10610451

FORD CROWN VICTORIA 2007 car safety problem was reported on July 14, 2014.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with ENGINE . the heat shield covering the left side engine exhaust manifold had corroded around the attaching bolts allowing the shield to fall against the steering shaft. i removed the shield before it could interfere with the steering function..0 person(s) were injured. 0 person(s) died.Mileage was 151200 miles. Vehicle Identification Number (VIN):2FAFP71W37X. Ford Crown Victoria 2007 problem was reported in VALENTINE, NE. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Unknown Or Other

Ford Crown Victoria 2007 Unknown Or Other Review #10610451

FORD CROWN VICTORIA 2007 car safety problem was reported on July 14, 2014.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with UNKNOWN OR OTHER . the heat shield covering the left side engine exhaust manifold had corroded around the attaching bolts allowing the shield to fall against the steering shaft. i removed the shield before it could interfere with the steering function..0 person(s) were injured. 0 person(s) died.Mileage was 151200 miles. Vehicle Identification Number (VIN):2FAFP71W37X. Ford Crown Victoria 2007 problem was reported in VALENTINE, NE. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Steering

Ford Crown Victoria 2007 Steering Review #10614982

FORD CROWN VICTORIA 2007 car safety problem was reported on Dec 13, 2013.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with STEERING . tl* the contact owns a 2007 ford crown victoria. the contact stated that while driving at various speeds, the power steering malfunctioned and the steering wheel became hard to maneuver. the contact mentioned that the vehicle was repaired under recall nhtsa campaign id number: 13v385000 (steering). however, the failure recurred. the authorized dealer had not confirmed if the upper portion of the steering shaft needed to be inspected and repaired when the recall repair was performed. the vehicle was to be taken back to the authorized dealer for further inspection, diagnosis and repair. the manufacturer was notified of the failure and provided no remedy. the approximate failure mileage was 103,000. updated 10/02/14*lj.0 person(s) were injured. 0 person(s) died.Mileage was 103000 miles. Vehicle Identification Number (VIN):2FAFP71W77X. Ford Crown Victoria 2007 problem was reported in BURLINGTON, NJ. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Crown Victoria 2007 Air Bags

Ford Crown Victoria 2007 Air Bags Review #10617590

FORD CROWN VICTORIA 2007 car safety problem was reported on July 12, 2014.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with AIR BAGS . tl* the contact owns a 2007 ford crown victoria. while making a right turn at approximately 20 mph, the passenger side of the vehicle t-boned by another vehicle, that ran a stop sign. the driver side air bag partially deployed. the contact sustained a fractured rib, bruised lungs, and contusions on the head. the passenger seated in the rear was fatally injured. a police report was filed. the vehicle was not repaired and the manufacturer was not notified. the vin was unavailable. the approximate failure mileage was 252,000. updated 8/28/14*cn the consumer stated the air bag caught fire. updated 09/18/14.Vehicle was involved in a crash. Vehicle was on fire. 1 person(s) were injured. 1 person(s) died.Mileage was 252000 miles. Ford Crown Victoria 2007 problem was reported in DETROIT, MI. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 20 mph.

Ford Crown Victoria 2007 Unknown Or Other

Ford Crown Victoria 2007 Unknown Or Other Review #10660312

FORD CROWN VICTORIA 2007 car safety problem was reported on Nov 10, 2014.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with UNKNOWN OR OTHER . had to replace the climate control head and the temperature blend door actuator on a vehicle with only 39,600 miles..0 person(s) were injured. 0 person(s) died.Mileage was 39600 miles. Vehicle Identification Number (VIN):2FAFP74V47X. Ford Crown Victoria 2007 problem was reported in CATONSVILLE, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2007 Steering

Ford Crown Victoria 2007 Steering Review #10661388

FORD CROWN VICTORIA 2007 car safety problem was reported on Nov 30, 2014.FORD CROWN VICTORIA 2007, manufactured by Ford Motor Company had a problem with STEERING . on 3/5/14, owner brought the vehicle, a 2007 ford crown victoria police, to an authorized ford dealer who completed factory recall 13s08 that called for replacing steering shaft assembly. on 11/30/14, when turning at approximately 10mph, the steering became very stiff requiring excessive physical force to turn the wheel. a collision with a pole was barely avoided. steering has remained stiff and sluggish despite checking power steering levels and tire pressure for proper inflation. owner considers the vehicle to be unsafe to drive at this point.. .0 person(s) were injured. 0 person(s) died.Mileage was 138000 miles. Vehicle Identification Number (VIN):2FAFP71W47X. Ford Crown Victoria 2007 problem was reported in HIGHLAND MILLS, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 10 mph.


Ford Crown Victoria 2007 Systems




Search 1000s of Car Reviews, Recalls and Technical Bulletins
Start by entering a car model, system, manufacturer or any combination of keywords.


Ford Crown Victoria 2007 Reports


my 95 ford exploere engine surges when turn my air conditioner on

Ihave a 1994 ford probe which has started to idle very low and stalls at times. It is a 4 cyl. w/ air and a 5 speed. any ideas? I replaced the fuel filter, air flow meter and added HEAT to gas tank to dry and clean fuel system. I think my pcv valv

should a standard transmission truck start when it is in gear without the clucth engaged?

should a 2005 standard transmission ford ranger start when in gear without the clutch engaged?

96 Ford F250 Emergency brake lever gets caught on the auto adjustment spring, causing brakes to be permanently engaged, also allowing the parking break lever to rub against the hub, which can cut through over time.

try pushing the pedals button closer to you. you must have the pedal adjustment button to the left of the radio, looks like a foot, that brings the pedals more inward towards the driver. hope it helped. or look carefully if a wire has corroded. it

i would check ur multi switch on ur stearing colum

on the pedal

whats the sound

Just bought an '06 E-350 van. Left d'ship got on highway and noticed shimmy when I got to 60....same problem????

that happened to me last night! If you rock the car back and for while shifting then it should release the safety lock!

why does it take turning off the veh. while pulling in on the shifter arm, them starting it again while still holding it inwards ever so slightly??

Discuss Ford Crown Victoria


No comments have been provided.