Car-and-Safety.com

Ford Crown Victoria 2006 Safety Reports and Reviews



Ford Crown Victoria 2006 Reviews



Ford Crown Victoria 2006 Service Brakes, Hydraulic

Ford Crown Victoria 2006 Service Brakes, Hydraulic Review #10164338

FORD CROWN VICTORIA 2006 car safety problem was reported on July 28, 2006.FORD CROWN VICTORIA 2006, manufactured by FORD MOTOR COMPANY had a problem with SERVICE BRAKES, HYDRAULIC . dt*: the contact stated there were on intermittent problems with the brakes. the vehicle has taken the vehicle to the dealer on four occasions for the same problems. while the engine was running and the vehicle was immobile with the brake pads applied, the vehicle surged forward. this almost caused serious accidents or crashes into pedestrians in some incidents. the vehicle was taken to the dealers and they could not duplicate the problem or determined the cause for the problem. after the last incident, the insurance company notified the contact that they would no longer cover the vehicle because of the potential cause of injuries and accidents due to the defect. the insurance company had the vehicle towed to the dealer for further investigation and service. the manufacturer was contacted and they determined the dealer would remedy the problem with the vehicle. dt: the contact stated that the vehicle experiences on going problems with the brakes and has taken the vehicle in to the dealers on four separate occasions for the same, intermittent problems. while the engine is on and the vehicle in a sitting position with the brake pads applied under normal conditions and with no warning, the vehicle surges forward and almost caused serious accidents or crashes into pedestrians in some incidents. the vehicle would be taken to the dealers and they could not duplicate the problem and cannot find the cause for the problem. on the last incident, the insurance company notified the contact that they would no longer cover the vehicle because of the potential cause of injuries and accidents due to the defect. the insurance company had the vehicle towed back to the dealers for further investigation and service. the manufacturer was called and stated that the dealers must remedy the vehicles defect. the vehicle is currently at the dealers under examination for the cause of the problem..Mileage was 12022 miles. Vehicle Identification Number (VIN):2FAFP74V96X. Ford Crown Victoria 2006 problem was reported in ATLANTA, GA. Original Owner. Vehicle was purchased on June 26, 2006. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. Ford Crown Victoria 2006 drive type:RWD. FUEL TYPE: GAS. Ford Crown Victoria 2006 TRANSMISSION TYPE: AUTO. DEALER'S NAME: LOU SOBH FORD .

Ford Crown Victoria 2006 Vehicle Speed Control

Ford Crown Victoria 2006 Vehicle Speed Control Review #10171330

FORD CROWN VICTORIA 2006 car safety problem was reported on Sept 19, 2006.FORD CROWN VICTORIA 2006, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . dt*: the contact stated while driving various speeds after depressing the brake pedal and stopping, the vehicle surged forward intermittently without warning. the vehicle was driven to the dealer several times however; the problem could not be duplicated. .Mileage was 795 miles. Vehicle Identification Number (VIN):2FAFP74V66X. Ford Crown Victoria 2006 problem was reported in CORAL GABLES, FL. Original Owner. Vehicle was purchased on May 08, 2006. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. Ford Crown Victoria 2006 drive type:AWD. FUEL TYPE: GAS. Ford Crown Victoria 2006 TRANSMISSION TYPE: AUTO. DEALER'S NAME: WORLD FORD OF KENDALL . DEALER'S CITY: SOUTH MIAMI . DEALER'S STATE CODE: FL.

Ford Crown Victoria 2006 Engine And Engine Cooling

Ford Crown Victoria 2006 Engine And Engine Cooling Review #10177281

FORD CROWN VICTORIA 2006 car safety problem was reported on Dec 27, 2006.FORD CROWN VICTORIA 2006, manufactured by FORD MOTOR COMPANY had a problem with ENGINE AND ENGINE COOLING . 2006 ford crown victoria purchased in june 2006. problem occurred about 1 mointh after purchase (late june). i was driving out of my apt complex, when i stopped at the gate, the engine suddenly went crazy. it was as if it had max throttle except my foot was on the brake not the accelerator pedal. if i had not had my foot on the brake, i would have crashed into the gate. i put the control into neutral and the engine continued to race for about 6-7 seconds, then it stopped and it was like nothing had happened. i took it to the dealer and they ran diagnostics. nothing wrong. so i said it was a fluke. but now 2 days ago (12-27-06), it happened again. i took it to the dealer and they ran diagnositics - again nothing wrong..0 person(s) were injured. 0 person(s) died.Mileage was 1000 miles. Vehicle Identification Number (VIN):2FAFP73V26X. Ford Crown Victoria 2006 problem was reported in LOVELAND, OH. Original Owner. Vehicle was purchased on June 06, 2006. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. Ford Crown Victoria 2006 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Crown Victoria 2006 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph. DEALER'S NAME: KINGS FORD . DEALER'S TELEPHONE NUMBER: 5136830220 . DEALER'S CITY: CINCINNATI . DEALER'S STATE CODE: OH. DEALER'S ZIPCODE: 45249 .

Ford Crown Victoria 2006 Visibility Power Window Devices And Controls

Ford Crown Victoria 2006 Visibility Power Window Devices And Controls Review #10189832

FORD CROWN VICTORIA 2006 car safety problem was reported on May 04, 2007.FORD CROWN VICTORIA 2006, manufactured by FORD MOTOR COMPANY had a problem with VISIBILITY:POWER WINDOW DEVICES AND CONTROLS . the first problem i was told was a "module sensor" possible o2 sensor. this was within two weeks of buying this brand new 06' ford crown vic. the second problem was a minor window malfunction. the latest problem we have is today my wife and grandson were in a accident. someone pulled out in front of us, we were traveling about 25-30 mph. we hit the other car on the passenger side head on. our airbags did not inflate. i am very very concerned this may be another "problem" with this 6 month old ford, with less that 4,000 miles on it. the websites for both the dealer and ford company are absolutely no help in trying to find answers to my situation. please contact me on how to get this matter resolved. *jb.Vehicle was involved in a crash. Mileage was 4400 miles. Vehicle Identification Number (VIN):2FAFP73V46X. Ford Crown Victoria 2006 problem was reported in LEXINGTON, NC. Accident was reported to Police. Original Owner. Vehicle was purchased on Nov 11, 2006. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. Ford Crown Victoria 2006 drive type:RWD. FUEL TYPE: GAS. Ford Crown Victoria 2006 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 30 mph. DEALER'S NAME: PARKWAY FORD . DEALER'S TELEPHONE NUMBER: 336-724-5921 . DEALER'S CITY: WINSTON-SALEM . DEALER'S STATE CODE: NC. DEALER'S ZIPCODE: 27102 .

Ford Crown Victoria 2006 Air Bags

Ford Crown Victoria 2006 Air Bags Review #10189832

FORD CROWN VICTORIA 2006 car safety problem was reported on May 04, 2007.FORD CROWN VICTORIA 2006, manufactured by FORD MOTOR COMPANY had a problem with AIR BAGS . the first problem i was told was a "module sensor" possible o2 sensor. this was within two weeks of buying this brand new 06' ford crown vic. the second problem was a minor window malfunction. the latest problem we have is today my wife and grandson were in a accident. someone pulled out in front of us, we were traveling about 25-30 mph. we hit the other car on the passenger side head on. our airbags did not inflate. i am very very concerned this may be another "problem" with this 6 month old ford, with less that 4,000 miles on it. the websites for both the dealer and ford company are absolutely no help in trying to find answers to my situation. please contact me on how to get this matter resolved. *jb.Vehicle was involved in a crash. Mileage was 4400 miles. Vehicle Identification Number (VIN):2FAFP73V46X. Ford Crown Victoria 2006 problem was reported in LEXINGTON, NC. Accident was reported to Police. Original Owner. Vehicle was purchased on Nov 11, 2006. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. Ford Crown Victoria 2006 drive type:RWD. FUEL TYPE: GAS. Ford Crown Victoria 2006 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 30 mph. DEALER'S NAME: PARKWAY FORD . DEALER'S TELEPHONE NUMBER: 336-724-5921 . DEALER'S CITY: WINSTON-SALEM . DEALER'S STATE CODE: NC. DEALER'S ZIPCODE: 27102 .

Ford Crown Victoria 2006 Steering Hydraulic Power Assist System

Ford Crown Victoria 2006 Steering Hydraulic Power Assist System Review #10191422

FORD CROWN VICTORIA 2006 car safety problem was reported on May 17, 2007.FORD CROWN VICTORIA 2006, manufactured by FORD MOTOR COMPANY had a problem with STEERING:HYDRAULIC POWER ASSIST SYSTEM . police track training personnel are reporting momentary power steering loss/lockup when executing hard u-turns with 06/07 production ford crown vic police interceptions. in addition, we are receiving complaints from the field regarding this same issue. concern is that this steering defect could result in an accident during normal patrol responses. this defect impacts at least one third of our active patrol fleet (over 175 cars, perhaps as many as 250). we are monitoring what police fleets in arizona are currently doing per the tsb issued by ford as well as scheduling a meeting with local ford technician., who, at our track demonstrated the problem for me on may 17, 2007. *ak.Vehicle Identification Number (VIN):2FAHP71W16X. Ford Crown Victoria 2006 problem was reported in FAIRFAX, VA. Original Owner. Vehicle was purchased on Sept 29, 2005. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. Ford Crown Victoria 2006 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Crown Victoria 2006 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 25 mph.

Ford Crown Victoria 2006 Vehicle Speed Control

Ford Crown Victoria 2006 Vehicle Speed Control Review #10192362

FORD CROWN VICTORIA 2006 car safety problem was reported on Jan 15, 2007.FORD CROWN VICTORIA 2006, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl*the contact owns a 2006 ford crown victoria. the contact stated that the vehicle accelerates when attempting to brake. the failure occurs intermittently and without warning. the dealer was unable to duplicate the failure. the purchase date was unknown. the current mileage is 27,000 and failure mileage was 24,989. update 07/06/07.*jb.0 person(s) were injured. 0 person(s) died.Mileage was 24989 miles. Vehicle Identification Number (VIN):2FAFP74V76X. Ford Crown Victoria 2006 problem was reported in LINWOOD, NC. Vehicle was purchased on Dec 01, 2006. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. Ford Crown Victoria 2006 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Crown Victoria 2006 TRANSMISSION TYPE: AUTO. DEALER'S NAME: THOMASVILLE FORD . DEALER'S TELEPHONE NUMBER: 336-472-7731 . DEALER'S CITY: THOMASVILLE . DEALER'S STATE CODE: NC.

Ford Crown Victoria 2006 Power Train Automatic Transmission Gear Position Indication (prndl)

Ford Crown Victoria 2006 Power Train Automatic Transmission Gear Position Indication (prndl) Review #10198422

FORD CROWN VICTORIA 2006 car safety problem was reported on Aug 01, 2007.FORD CROWN VICTORIA 2006, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL) . 2006 ford crown victoria. shift-lock mechanism was out of alignment and had a loose bolt preventing the transmission to go fully info park causing car to remain in neutral at failure point. a loose shifter created a "dead" spot between park and reverse gears. car drifted forward. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 35300 miles. Ford Crown Victoria 2006 problem was reported in COCOA, FL. Vehicle was purchased on July 01, 2005. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Crown Victoria 2006 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Crown Victoria 2006 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph. DEALER'S NAME: DMS . DEALER'S CITY: TALLAHASSEE . DEALER'S STATE CODE: FL.

Ford Crown Victoria 2006 Power Train Automatic Transmission Lever And Linkage Column Shift

Ford Crown Victoria 2006 Power Train Automatic Transmission Lever And Linkage Column Shift Review #10198422

FORD CROWN VICTORIA 2006 car safety problem was reported on Aug 01, 2007.FORD CROWN VICTORIA 2006, manufactured by FORD MOTOR COMPANY had a problem with POWER TRAIN:AUTOMATIC TRANSMISSION:LEVER AND LINKAGE:COLUMN SHIFT . 2006 ford crown victoria. shift-lock mechanism was out of alignment and had a loose bolt preventing the transmission to go fully info park causing car to remain in neutral at failure point. a loose shifter created a "dead" spot between park and reverse gears. car drifted forward. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 35300 miles. Ford Crown Victoria 2006 problem was reported in COCOA, FL. Vehicle was purchased on July 01, 2005. Vehicle was using ANTI-LOCK BRAKES.Vehicle was not using Cruise Control. Vehicle had 6 CYLINDERS. Ford Crown Victoria 2006 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Crown Victoria 2006 TRANSMISSION TYPE: AUTO. VEHICLE SPEED: 0 mph. DEALER'S NAME: DMS . DEALER'S CITY: TALLAHASSEE . DEALER'S STATE CODE: FL.

Ford Crown Victoria 2006 Structure Body

Ford Crown Victoria 2006 Structure Body Review #10257662

FORD CROWN VICTORIA 2006 car safety problem was reported on Jan 13, 2009.FORD CROWN VICTORIA 2006, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE:BODY . we have 21 2006 ford police interceptor police cars. everyone of them is experiencing paint cracks and or paint popping off the roof or quarter panels by the rear window. you can see the gray primer in the exposed areas where the white paint has popped off. ford denies the problem. all of the vehicles in my police fleet have between 50,000 and 65,000 miles. we took delivery of all of these vehicles in january 2006. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 51000 miles. Vehicle Identification Number (VIN):2FAHP71W46X. Ford Crown Victoria 2006 problem was reported in ARNOLD, MO. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2006 Structure Review #10341923

FORD CROWN VICTORIA 2006 car safety problem was reported on May 07, 2010.FORD CROWN VICTORIA 2006, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE . paint is failing all over car: hood, roof, side molding, and bumpers. *tr.Mileage was 93000 miles. Vehicle Identification Number (VIN):2FAFP74VX6X. Ford Crown Victoria 2006 problem was reported in EAGLE LAKE, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2006 Vehicle Speed Control

Ford Crown Victoria 2006 Vehicle Speed Control Review #10359576

FORD CROWN VICTORIA 2006 car safety problem was reported on Aug 16, 2010.FORD CROWN VICTORIA 2006, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2006 ford crown victoria. while driving at an unknown speed the vehicle accelerated. the contact engaged the brakes and placed the vehicle in neutral and the vehicle stopped. the failure only happen once. the vehicle was taken to an authorized dealer and the dealer replaced the brake deactivation switch. the vehicle was repaired. the failure mileage was approximately 140,000 and the current mileage was 143,551. .Mileage was 140000 miles. Vehicle Identification Number (VIN):2FAFP71W66X. Ford Crown Victoria 2006 problem was reported in MEDFORD, WI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Crown Victoria 2006 Vehicle Speed Control Review #10359577

FORD CROWN VICTORIA 2006 car safety problem was reported on Sept 10, 2010.FORD CROWN VICTORIA 2006, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . tl*the contact owns a 2006 ford crown victoria. while driving approximately 20 mph, the vehicle suddenly accelerated. the contact depressed the brake pedal so firmly that the tires began smoking. the brakes would not stop the vehicle. the contact shifted into neutral to stop the acceleration. the vehicle was taken to an authorized dealer where the brake deactivation switch was replaced. the contact filed a complaint with the manufacturer. the current and failure mileages were 108,774. .Mileage was 108774 miles. Vehicle Identification Number (VIN):2FAFP71W06X. Ford Crown Victoria 2006 problem was reported in MEDFORD, WI. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 20 mph.

Ford Crown Victoria 2006 Structure Body

Ford Crown Victoria 2006 Structure Body Review #10458274

FORD CROWN VICTORIA 2006 car safety problem was reported on May 04, 2010.FORD CROWN VICTORIA 2006, manufactured by FORD MOTOR COMPANY had a problem with STRUCTURE:BODY . paint peeled off roof and both "c" pillars. ford has a tsb (09n02) but will not help crown victoria police interceptor owners who are not government agencies or cvpi's that are not in law enforcement/government service. was forced to pay out-of pocket for repaint of effected areas. now i noticed that paint is peeling off hood. i tried the dealer, who called ford corporate and they told the dealership they could not help me because the vehicle is not in service and privately owned. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 48721 miles. Vehicle Identification Number (VIN):2FAHP71W96X. Ford Crown Victoria 2006 problem was reported in DELAWARE, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: DIESEL.

Ford Crown Victoria 2006 Vehicle Speed Control

Ford Crown Victoria 2006 Vehicle Speed Control Review #10468681

FORD CROWN VICTORIA 2006 car safety problem was reported on Feb 01, 2012.FORD CROWN VICTORIA 2006, manufactured by FORD MOTOR COMPANY had a problem with VEHICLE SPEED CONTROL . the driver of the above listed vehicle stated that while pressing the brake of the vehicle, the vehicle unintentionally accelerated and struck a wall. the throttle body unit was replaced at a ford dealership. on approximately july 13, 2012, the driver stated that there was another unintentional acceleration while braking but no accident occurred in this case. we have had other reports of a similar nature with three 2006 ford cvpi's and approximately two 2004 cvpi's..Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Vehicle Identification Number (VIN):2FAHP71W06X. Ford Crown Victoria 2006 problem was reported in ALEXANDRIA, VA. Accident was reported to Police. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was using Cruise Control.Vehicle had 8 CYLINDERS. Ford Crown Victoria 2006 drive type:RWD. FUEL SYSTEM:Fuel injection. FUEL TYPE: GAS. Ford Crown Victoria 2006 TRANSMISSION TYPE: AUTO.

Ford Crown Victoria 2006 Steering

Ford Crown Victoria 2006 Steering Review #10474596

FORD CROWN VICTORIA 2006 car safety problem was reported on Sept 05, 2012.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with STEERING . catastrophic failure of the steering column; the steering column retaining ring failed. binding of lower and middle universal joints and believe it is heat related. steering shaft not traveling on a true axis and a result is the retaining ring is being worn and eventually wears out. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 76672 miles. Vehicle Identification Number (VIN):2FAFP71W26X. Ford Crown Victoria 2006 problem was reported in ROCKVILLE, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2006 Steering Review #10474598

FORD CROWN VICTORIA 2006 car safety problem was reported on July 09, 2012.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with STEERING . catastrophic failure of the steering column; the steering column retaining ring failed. binding of lower and middle universal joints and believe it is heat related. steering shaft not traveling on a true axis and a result is the retaining ring is being worn and eventually wears out. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 74718 miles. Vehicle Identification Number (VIN):2FAFP71W16X. Ford Crown Victoria 2006 problem was reported in ROCKVILLE, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2006 Steering Review #10475017

FORD CROWN VICTORIA 2006 car safety problem was reported on Sept 11, 2012.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with STEERING . catastrophic failure of the steering column; the steering column retaining ring failed. binding of lower and middle universal joints and believe it is heat related. steering shaft not traveling on a true axis and a result is the retaining ring is being worn and eventually wears out. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 130725 miles. Vehicle Identification Number (VIN):2FAFP71W46X. Ford Crown Victoria 2006 problem was reported in ROCKVILLE, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2006 Steering Review #10475153

FORD CROWN VICTORIA 2006 car safety problem was reported on Sept 12, 2012.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with STEERING . catastrophic failure of the steering column; the steering column retaining ring failed. binding of the lower and middle universal joints and believe it is heat related? steering shaft not traveling on a true axis and a result is the retaining ring is being worn and eventually wears out. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 103565 miles. Vehicle Identification Number (VIN):2FAFP71W76X. Ford Crown Victoria 2006 problem was reported in ROCKVILLE, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2006 Steering Review #10475578

FORD CROWN VICTORIA 2006 car safety problem was reported on Sept 14, 2012.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with STEERING . catastrophic failure of the steering column; column separating and total failure imminent. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 77118 miles. Vehicle Identification Number (VIN):2FAFP71W06X. Ford Crown Victoria 2006 problem was reported in ROCKVILLE, MD. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2006 Steering Review #10476886

FORD CROWN VICTORIA 2006 car safety problem was reported on Sept 12, 2012.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with STEERING . tl* the contact owns a 2006 ford crown victoria. the contact stated that the vehicle was taken to an independent mechanic for inspection of a steering failure. the mechanic advised the contact that the steering column bushing on the upper steering column was loose. in addition, the mechanic advised the contact of a concurrent investigation pertaining to the failure under nhtsa action number: pe12025 (steering:column). the investigation was for the same year, make and model but only included those vehicles being used as police interceptor (cvpi) vehicles. the vehicle was not repaired. the approximate failure mileage was 88,329. .0 person(s) were injured. 0 person(s) died.Mileage was 88329 miles. Vehicle Identification Number (VIN):2FAFP71W96X. Ford Crown Victoria 2006 problem was reported in LA VERNE, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2006 Steering Review #10478029

FORD CROWN VICTORIA 2006 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with STEERING . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 151080 miles. Vehicle Identification Number (VIN):2FAHP71WX6X. Ford Crown Victoria 2006 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2006 Suspension

Ford Crown Victoria 2006 Suspension Review #10478029

FORD CROWN VICTORIA 2006 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with SUSPENSION . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 151080 miles. Vehicle Identification Number (VIN):2FAHP71WX6X. Ford Crown Victoria 2006 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2006 Steering

Ford Crown Victoria 2006 Steering Review #10478031

FORD CROWN VICTORIA 2006 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with STEERING . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 124389 miles. Vehicle Identification Number (VIN):2FAHP71W56X. Ford Crown Victoria 2006 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2006 Suspension

Ford Crown Victoria 2006 Suspension Review #10478031

FORD CROWN VICTORIA 2006 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with SUSPENSION . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 124389 miles. Vehicle Identification Number (VIN):2FAHP71W56X. Ford Crown Victoria 2006 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2006 Steering

Ford Crown Victoria 2006 Steering Review #10478038

FORD CROWN VICTORIA 2006 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with STEERING . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 111320 miles. Vehicle Identification Number (VIN):2FAHP71W06X. Ford Crown Victoria 2006 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2006 Suspension

Ford Crown Victoria 2006 Suspension Review #10478038

FORD CROWN VICTORIA 2006 car safety problem was reported on Sept 26, 2012.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with SUSPENSION . inspection found dislocated bushing. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 111320 miles. Vehicle Identification Number (VIN):2FAHP71W06X. Ford Crown Victoria 2006 problem was reported in HARRISBURG, PA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 0 mph.

Ford Crown Victoria 2006 Electrical System

Ford Crown Victoria 2006 Electrical System Review #10481494

FORD CROWN VICTORIA 2006 car safety problem was reported on Oct 22, 2012.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with ELECTRICAL SYSTEM . was driving down hwy when i smelt electrical burning and noticed smoke coming from around the steering wheel. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 159000 miles. Vehicle Identification Number (VIN):2FAFP71W76X. Ford Crown Victoria 2006 problem was reported in KATY, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Crown Victoria 2006 Steering

Ford Crown Victoria 2006 Steering Review #10481494

FORD CROWN VICTORIA 2006 car safety problem was reported on Oct 22, 2012.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with STEERING . was driving down hwy when i smelt electrical burning and noticed smoke coming from around the steering wheel. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 159000 miles. Vehicle Identification Number (VIN):2FAFP71W76X. Ford Crown Victoria 2006 problem was reported in KATY, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 40 mph.

Ford Crown Victoria 2006 Vehicle Speed Control

Ford Crown Victoria 2006 Vehicle Speed Control Review #10500821

FORD CROWN VICTORIA 2006 car safety problem was reported on Feb 14, 2013.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2006 ford crown victoria. the contact stated that while driving around a traffic circle, the engine rpms increased excessively as the vehicle accelerated independently. the contact applied the brakes and continued to depress the pedal until the engine rpms and speed of the vehicle decreased. the failure recurred twice. the initial failure was minor however, the second failure was much worse. the vehicle was not taken to the dealer or a mechanic for inspection or repairs. the contact stated that the vehicle was once used as a police vehicle. the failure mileage was 100,000. .0 person(s) were injured. 0 person(s) died.Mileage was 100000 miles. Vehicle Identification Number (VIN):2FAFP71W46X. Ford Crown Victoria 2006 problem was reported in MIAMI, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Crown Victoria 2006 Steering

Ford Crown Victoria 2006 Steering Review #10505992

FORD CROWN VICTORIA 2006 car safety problem was reported on Apr 09, 2013.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with STEERING . i was driving approax 25 mph when my steering wheel all of a sudden became free and my wheel just spun freely not moving my wheels, upon inspection i found that the bushing dislocated which caused me to loose control of my steering. *tr.Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Mileage was 168329 miles. Vehicle Identification Number (VIN):2FAHP71W16X. Ford Crown Victoria 2006 problem was reported in LUARELVILLE, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 25 mph.

Ford Crown Victoria 2006 Service Brakes

Ford Crown Victoria 2006 Service Brakes Review #10514870

FORD CROWN VICTORIA 2006 car safety problem was reported on Feb 14, 2013.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with SERVICE BRAKES . tl* the contact owns a 2006 ford crown victoria. the contact stated that while driving at 30 mph and depressing the brake pedal, the vehicle hesitated to stop. after the vehicle came to a stop, and while contact slightly removed their foot from the brake pedal. the vehicle then accelerated and crashed into the preceding vehicle. the contact did not sustain any injuries. the contact mentioned that the failure was experienced several times. the vehicle was not repaired. the failure was reported to the manufacturer. the failure mileage was 104,940. the current mileage was 106,000. .Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Mileage was 104940 miles. Vehicle Identification Number (VIN):2FAFP74V06X. Ford Crown Victoria 2006 problem was reported in ALDERSON, WV. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Ford Crown Victoria 2006 Vehicle Speed Control

Ford Crown Victoria 2006 Vehicle Speed Control Review #10514870

FORD CROWN VICTORIA 2006 car safety problem was reported on Feb 14, 2013.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with VEHICLE SPEED CONTROL . tl* the contact owns a 2006 ford crown victoria. the contact stated that while driving at 30 mph and depressing the brake pedal, the vehicle hesitated to stop. after the vehicle came to a stop, and while contact slightly removed their foot from the brake pedal. the vehicle then accelerated and crashed into the preceding vehicle. the contact did not sustain any injuries. the contact mentioned that the failure was experienced several times. the vehicle was not repaired. the failure was reported to the manufacturer. the failure mileage was 104,940. the current mileage was 106,000. .Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Mileage was 104940 miles. Vehicle Identification Number (VIN):2FAFP74V06X. Ford Crown Victoria 2006 problem was reported in ALDERSON, WV. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.

Ford Crown Victoria 2006 Exterior Lighting

Ford Crown Victoria 2006 Exterior Lighting Review #10532684

FORD CROWN VICTORIA 2006 car safety problem was reported on July 04, 2013.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with EXTERIOR LIGHTING . the headlights on my 2005 ford crown victoria turned off without any indication of a problem beforehand. the lights came on for a while, then went back off and the problem has been repetitive over the past several days. what is alarming about this - is that it happened on the freeway at a speed of 65 mph. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 44228 miles. Vehicle Identification Number (VIN):2FAFP74W65X. Ford Crown Victoria 2006 problem was reported in PALM SPRINGS, CA. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

Ford Crown Victoria 2006 Steering

Ford Crown Victoria 2006 Steering Review #10542794

FORD CROWN VICTORIA 2006 car safety problem was reported on Aug 18, 2013.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with STEERING . steering went out of vehicle. had bad column replaced, and got vehicle back on aug 29, 2013. again steering column failed and went back out on aug 30 , 2013. vehicle was moving approximately 25 mph. fortunately we were to stop the vehicle but ran into hillside, and luckily no one was hurt. the column was replaced again and additionally this time the lower shaft was replaced. *tr.Vehicle was involved in a crash. 0 person(s) were injured. 0 person(s) died.Mileage was 176000 miles. Vehicle Identification Number (VIN):2FAFP71W86X. Ford Crown Victoria 2006 problem was reported in ST. CLAIRSVILLE, OH. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 25 mph.

Ford Crown Victoria 2006 Air Bags

Ford Crown Victoria 2006 Air Bags Review #10548798

FORD CROWN VICTORIA 2006 car safety problem was reported on Oct 01, 2011.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with AIR BAGS . air bag passive restraint system default alarm light and alarm sound goes off when driving down the highway. this happened randomly multiple times over a period of 6-18 months. sometimes i find blown fuses, other times analytical tools suggest bad passive restraint ground. currently unknown condition and unknown if air bag system actually works. car has experienced dozens of failures like this, directional failures, parking brake failure, gas cut off failure, cooling fan failure, paint failure, remote mirror failure, window control switch failure, defrost failure, heat control failure, ignition failure, and many more. passive restraint system failure is just one of the many i have been perplexed by. of all the failures, ford only accepted the gas shut off failure. i can not afford to keep the automobile operating. *tr.0 person(s) were injured. 0 person(s) died.Mileage was 75000 miles. Vehicle Identification Number (VIN):2FAFP74W26X. Ford Crown Victoria 2006 problem was reported in SAN ANTONIO, FL. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 45 mph.

Ford Crown Victoria 2006 Steering

Ford Crown Victoria 2006 Steering Review #10565961

FORD CROWN VICTORIA 2006 car safety problem was reported on Oct 01, 2013.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with STEERING . tl- the contact owns a 2006 crown victoria. the contact stated that her vehicle was included in nhtsa campaign number 13v385000 (steering) and the recall had exceeded a reasonable time for repair. the vehicle also experienced the steering failure. the dealer advised the contact that the part was not available and they did not know when the manufacturer was going to release the part. the contact was placed on a waiting list that will also exceed several months before the vehicle will be repaired. the failure and current mileage was 191,323. rk .0 person(s) were injured. 0 person(s) died.Mileage was 191323 miles. Vehicle Identification Number (VIN):2FAHP71W06X. Ford Crown Victoria 2006 problem was reported in WHITESTONE, NY. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Crown Victoria 2006 Steering Review #10631206

FORD CROWN VICTORIA 2006 car safety problem was reported on Sept 05, 2014.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with STEERING . after driving to xyz location 3 miles from my home i parked my car for a while to pick up stuff from the place. after around 30 minutes i just drove my [xxx] ford crown vic 2006 p71 an ex police car from the parking lot. just as i just accelerated and turned the vehicle towards my intended direction all of a sudden i completely lost control on my steering wheel. recently i have had a recall on a steering wheel shaft and i got it replaced at ford dealership; furthermore i presume that loosing the control of steering wheel this time is related to the previous recall repair. i left my car at ford dealership for further investigation. information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6). *tr.0 person(s) were injured. 0 person(s) died.Mileage was 170000 miles. Vehicle Identification Number (VIN):2FAFP71W96X. Ford Crown Victoria 2006 problem was reported in BEAUMONT, TX. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. Vehicle had 8 CYLINDERS. FUEL TYPE: GAS. VEHICLE SPEED: 10 mph.

Ford Crown Victoria 2006 Steering Review #10637321

FORD CROWN VICTORIA 2006 car safety problem was reported on July 01, 2014.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with STEERING . tl* the contact owns a 2006 ford crown victoria. while making a right turn at an unknown speed, the steering wheel seized and became very difficult to maneuver. the vehicle was repaired according to nhtsa campaign number: 13v385000 (steering); however, the failure persisted. the dealer stated that the upper intermediate shaft needed to be replaced. the vehicle was not repaired and the manufacturer was made aware of the failure. the approximate failure mileage was 130,000. .0 person(s) were injured. 0 person(s) died.Mileage was 130000 miles. Vehicle Identification Number (VIN):2FAFP71W26X. Ford Crown Victoria 2006 problem was reported in DEMOTTE, IN. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control.

Ford Crown Victoria 2006 Electrical System

Ford Crown Victoria 2006 Electrical System Review #10672504

FORD CROWN VICTORIA 2006 car safety problem was reported on Dec 17, 2014.FORD CROWN VICTORIA 2006, manufactured by Ford Motor Company had a problem with ELECTRICAL SYSTEM . i turned on the head lights applied the bright lights and lights went off. the next day the engine indicator went on after purchasing gas. five days later i purchased gas and the low fuel light indicator came on and the gage showed empty after fueling the vehicle up. .0 person(s) were injured. 0 person(s) died.Mileage was 129279 miles. Vehicle Identification Number (VIN):2FAHP71W16X. Ford Crown Victoria 2006 problem was reported in INMAN, SC. Vehicle was not using ANTI-LOCK BRAKES. Vehicle was not using Cruise Control. VEHICLE SPEED: 30 mph.


Ford Crown Victoria 2006 Systems




Search 1000s of Car Reviews, Recalls and Technical Bulletins
Start by entering a car model, system, manufacturer or any combination of keywords.


Ford Crown Victoria 2006 Reports


my 95 ford exploere engine surges when turn my air conditioner on

Ihave a 1994 ford probe which has started to idle very low and stalls at times. It is a 4 cyl. w/ air and a 5 speed. any ideas? I replaced the fuel filter, air flow meter and added HEAT to gas tank to dry and clean fuel system. I think my pcv valv

should a standard transmission truck start when it is in gear without the clucth engaged?

should a 2005 standard transmission ford ranger start when in gear without the clutch engaged?

96 Ford F250 Emergency brake lever gets caught on the auto adjustment spring, causing brakes to be permanently engaged, also allowing the parking break lever to rub against the hub, which can cut through over time.

try pushing the pedals button closer to you. you must have the pedal adjustment button to the left of the radio, looks like a foot, that brings the pedals more inward towards the driver. hope it helped. or look carefully if a wire has corroded. it

i would check ur multi switch on ur stearing colum

on the pedal

whats the sound

Just bought an '06 E-350 van. Left d'ship got on highway and noticed shimmy when I got to 60....same problem????

that happened to me last night! If you rock the car back and for while shifting then it should release the safety lock!

why does it take turning off the veh. while pulling in on the shifter arm, them starting it again while still holding it inwards ever so slightly??

Discuss Ford Crown Victoria


No comments have been provided.